Color Wheel BP96-00674A SAMSUNG
|
Replacement of the SAMSUNG Color Wheel BP96-00674A Color Wheel Replacement No.:
Click below to buy this Color Wheel now: There are some Samsung DLP-TV production series that use two different kind of color wheel in the optic system, one is a ball bearing based system and the other is an air suspension system. While the two color wheels have the same diameter and look the same they are not compatible in any way, and cannot be swapped. The only way around this is to change the complete housing and wheel from one type and replace it with the other complete assembly type. To do this you must firs consider the following conditions.
 Location of jumper CN810 inside TV  DMD board with aluminum cover on  Back of DMD board attached to Light Engine  Highlight of Jumper CN810  Close up of jumper location. Remember:
Here are the differences between both color wheels.
Click below to buy this Color Wheelnow: Check out this site, not only do they carry and sell this color wheel, but also lots of spare parts for your TV / DLP / Plasma and LCD. They deliver to most city in the world.
http://www.discount-merchant.com
|
17
sean says:
November 3, 2008 at 10:48 pm
hello,
i recently changed my color wheel on my 42″ samsung dlp tv. the noise has stopped but now the color and alignment is off. everybody on the tv looks blue. please let me know what i can do to fix this. thanks!
Neil says:
February 28, 2009 at 7:14 pm
I have hte same problem. Did you get an answer to your query?
Drew says:
March 25, 2009 at 9:57 am
Is there a way to find out which color wheel my TV has before I open it up? I have a 46″ Samsung DLP.
FixYourDLP.com says:
March 25, 2009 at 1:52 pm
Drew,
We could probably help you out but we need the model # of your TV. Also, check out http://www.fixyourdlp.com/forum/
Donna says:
May 16, 2010 at 9:19 am
I am looking for detailed installation instructions on “How to replace a Color Wheel” in my HLP5063W DLP does anyone know where I might find these? I have searched and can only come up with some pictures, but not from start to finish. Thanks
Mark says:
August 27, 2010 at 7:00 am
There is a good video on youtube that covers the HPL5063W. Just search for Samsung color wheel. It’s 5 parts. It only took me about 15 minutes to remove the old one after watching that a few times.
Paul Rueger says:
August 16, 2010 at 8:19 pm
You guys ROCK! Never have I seen so much detail for anything related electronics as I have with your site. I have shopped with you guys before but I almost feel I want to quit my job and do TV repair after the things I learn on your site!
keep up the good work!!
Paul
Nicole says:
February 14, 2011 at 1:07 pm
I have an HLP6163W and bought and installed a color wheel (http://www.discount-merchant.com/product-p/samsung-bp96-00674a-cw-enc.htm?1=1&CartID=0). However, the area on my TV where this jumper is supposed to be (pictured above) is covered by a black plastic piece that is screwed on from the inside (ie I can’t remove it). I haven’t tested the TV yet, but is there anyone else who ran into this problem, or any moderator who can help me? Thanks.
James says:
June 18, 2011 at 5:40 am
Would this colour wheel work on a Samsung SP46L3HX? It looks like it fits
Brian Nordquist says:
September 14, 2011 at 7:59 pm
Thank you so much for the info about removing the pin..you saved me a lot of time and aggravation!!!
Chris Noshad says:
September 29, 2011 at 12:51 pm
I have an HLP6163W. I brught and installed a color wheel samsung-bp96-00674a. I also removed the jumper. However, the TV does not turn on when I plug the power. Even the projectopr lamp does not light up. The blinking light on the front of the TV turn on botton says “lamp”.
Is there anyone else who ran into this problem, or any moderator who can help me?
Thanks.
Chris Noshad says:
September 29, 2011 at 12:53 pm
PS,
I forgot to mention that the projector lamp is new and it was installed 5-6 months ago.
Chris Noshad says:
September 30, 2011 at 7:27 am
I have another confession to make. The Stand By/Temp light on the power button is also flashing!
Also, the two wires that connect to the projector lamp base are not hot or live when the power is on. No power is coming to the projector lamp. Any advise please.
Thor Sloan says:
October 5, 2011 at 7:23 am
Hey Chris..I ran across the same problem. I hate to say it, but you need to pull your unit back out and check to make sure you have your ribbon to the color wheel plugged in properly. It will fit both ways, you need to have the metallic strips facing the pins in the connector. My light is in and now all I have is colored squares. Now I need to investigate that. I do have sound, but no clear picture. Anyone have any ideas ?? Thanks again..
Thor Sloan
Evan says:
October 27, 2011 at 9:28 am
http://www.ebay.com/itm/Samsung-Color-wheel-BP96-00674A-HOUSING-/260477735472?pt=LH_DefaultDomain_0&hash=item3ca5aed230
Great place to purchase the BP96-00674A color wheel with housing.
Ken says:
January 6, 2012 at 4:11 pm
What happens if the CN810 Jumper is wrong? I removed and replaced a silver “Air Bearing” color wheel but the CN810 Jumper is “Inserted” How can I tell if this is right or not?