Your guide to replacing the PowerLite Pro Cinema 9700 UB projector lamp

Epson- PowerLite-Pro-Cinema-9700-UB-projector-Epson- ELPLP49-lampWeak picture? Flashing red lights? Time to replace the Epson PowerLite Pro Cinema 97000 UB projector lamp

Follow out 3-step guide to installing a PowerLite Pro Cinema 9700 UB projector lamp.

Step 1: Know when to replaceEpson-ELPLP49-Lamp-Light

Watch for the signs that it’s time to replace the Epson ELPLP49 projector lamp:

  • The projector image gets darker and starts to deteriorate.
  • The projector lamp flashes red.
  • The warning message REPLACE THE LAMP appears on screen.

A replacement warning message will also appear on screen. You can expect 4000 hours of lamp from the lamp depending on the settings and usage.

Find this authentic lamp on Amazon sold by these authorized dealers:

6 reasons to buy authentic

The Internet has been flooded with companies selling projector lamps.

Many advertised their lamps as “generic and compatible” – a euphemism for a knock-off, copycat technology that produces an inferior and dangerous product. Don’t believe the cheap prices you see as there are hidden costs to installing generic lamps.

You get what you pay for and in the case of generic lamps it’s usually a long list of problems:

Be sure the purchase an authentic Epson ELPLP49 projector lamp for your Epson PowerLite Pro Cinema 9700 UB projector. Save yourself unnecessary headaches and buy authentic from a recognized dealer. You’ll be getting a far superior product with a replacement guarantee and tech support.

Read more about the 7 Ways to Spot a Counterfeit Lamp.

Install a new Epson ELPLP49 lamp

Before installation:

  • Turn power button off wait for light to stop flashing
  • Turn off power swtich on the back of the Epson PowerLite Pro Cinema 9700 UB projector
  • Unplug the power cord
  • Allow the Epson PowerLite Pro Cinema 9700 UB to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
  • Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

 

Epson- PowerLite-Pro-Cinema-9700-UB-projector-Epson- ELPLP49-lamp1. The lamp cover for the Epson PowerLite Pro Cinema 9700 UB.
is found on top of the projector. Take the screwdriver that came with the projector and put it into opening on the lamp cover to release the cover switch. Remove the lamp cover.

Epson- PowerLite-Pro-Cinema-9700-UB-projector-remove-scews-Epson ELPLP49-lamp

2. Remove the two screws on either side of Epson ELPLP49 lamp. Place the screws to either side.

Epson- PowerLite-Pro-Cinema-9700-UB-projector-remove-Epson ELPLP49-lamp

3. Pull the lamp out using the top handle. Be sure to pull it out straight. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP49 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps! 

Epson- PowerLite-Pro-Cinema-9700-UB-projector-install-lamp-Epson ELPLP49-lamp

4. Take the new Epson ELPLP49 lamp by the handle and gently put it into place making sure the lamp is facing in the right direction.

Epson- PowerLite-Pro-Cinema-9700-UB-projector-tighten-lamp-Epson ELPLP49-lamp

5. Replace the Epson ELPLP49 screws on the newly installed lamp.

Epson- PowerLite-Pro-Cinema-9700-UB-projector-lamp-cover-on-Epson ELPLP49-lamp

6. Re-connect the lamp cover. Tighten the screws on the cord and turn on the Epson PowerLite Pro Cinema 9700 UB projector.

7. Re-attach the power cord. Turn the projector on and let it warm up.

8. Reset the Lamp Operating time.

Reset the Epson Lamp Timer

Reset the Epson PowerLite Pro Cinema 9700 UB Lamp Replacement Counter only when the Epson ELPLP49 lamp has been replaced.

Epson- PowerLite-Pro-Cinema-9700-UB-projector-reset-lamp-counter-menu1-Epson- ELPLP49-lamp

  • Turn the Epson PowerLite Pro Cinema 9700 UB projector on.
  • Press MENU to display the configuration menu.
  • Press the down arrow to move down the menu to the Reset option.

 

 

 

pson- PowerLite-Pro-Cinema-9700-UB-projector-reset-lamp-counter-menu2-Epson- ELPLP49-lamp

  • Press Enter to enter the Reset Menu.
  • Press the down arrow to move down the menu to the Reset Lamp Hours option.
  • Press Enter.

 

 

 

 PowerLite-Pro-Cinema-9700-UB-projector-reset-lamp-counter-menu3-Epson- ELPLP49-lamp

  • When the Reset Lamp Hour option has been chosen the Reset Lamp Hours message will appear.
  • Use the cursor to move to the YES option.
  • Press Enter to reset the lamp hours to zero.

Prolong the life of the Epson ELPLP49 lamp:

Extend the life of the newly installed Epson ELPLP49 with the following tips:

  • Keep your air filters clean to avoid overheating the projector.
  • Turn off the Epson PowerLite Pro Cinema 9700 UB and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
  • Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
  • Learn more with Top tips for extending DLP projector lamp life

 

Tagged with: , , ,

Leave a Reply

Your email address will not be published. Required fields are marked *

*

Time limit is exhausted. Please reload CAPTCHA.

This site uses Akismet to reduce spam. Learn how your comment data is processed.