Epson EB-410W projector lamp

Follow this step-by-step guide to replace Epson EB-410W projector lamp

Watch for the warning signs that it’s time to replace the Epson EB-410W projector lamp.

Dark image
Image that has deteriorated
On warning message appears on screen
Lamp light flashes orange

You can expect close to 2900 hours at high brightness and close to 3900 hours at low brightness.

Authentic vs generic lamps

The Internet has been flooded with many different choices for lamps. Unfortunately many are not authentic lamps and have been created by copycat manufacturers.

In order to keep your Epson EB-410W working at its optimum levels and to prevent damage, you’ll want to buy an authentic projector lamp. The Internet is flooded with companies offering “generic” compatible lamps. Although they seem like a bargain, these should be avoided. They have some very serious flaws:

generic have a much shorter lamp life than OEM lamps
copycat lamps are often created with toxic materials and carcinogenic parts including Krypton-85
compatible lamps are prone to explosions
generic lamps are not calibrated properly and can the sensitive electronics in projectors
copycat manufacturers offer no guarantee or refunds
the warranty on your Epson EB-410W projector will become void.

Learn how to spot the copycat fake lamps with 7 Ways to Spot a Counterfeit Lamp.

Buy this lamp on Amazon sold by these authorized dealers:

Installing the Epson ELPLP42

Before installation:

Turn off power switch on the back of the Epson EB-410W projector.
After you turn off the projector’s power and the confirmation buzzer beeps twice, disconnect the power cable
Allow the Epson EB-410W projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

1. The lamp cover is found on top of the Epson EB-410W projector. Loosen the lamp cover screw — you can’t remove it only loosen it.

2. Slide the Epson EMP-410W projector lamp cover off.

3. Loosen the two screws holding the Epson ELPLP42 lamp in place.

4. Grab the Epson ELPLP42 lamp by the two indents on the lamp. Gently remove the lamp. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP42 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

5. Gently insert the Epson ELPLP42 lamp making sure it’s facing the right way. NOTE: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

6. Tighten the screws on the new Epson ELPLP42 lamp.

7. Replace the lamp cover and tighten the screw on the Epson EB-410W projector lamp cover.

8. Reset the lamp timer.

Reset the lamp timer

Reset the Epson EB-410W projector Lamp Replacement Counter only when the Epson ELPLP42 lamp has been replaced.

Press the MENU button on the remote control. The Lamp Reset Menu will appear.
Scroll down to the RESET. Press ENTER.
Click on RESET ALL.
A prompt appears asking if you want to replace the lamp.
Select YES and press ENTER.Press MENU to exit.

Prolong the life of the Epson ELPLP42 lamp:

Extend the life of the newly installed Epson ELPLP42 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson EB-410W projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life

How to replace the Epson EB-410W projector lamp