Installing a NEC M260X projector lamp

NEC_M260X_projectr_NE_NP15LP_projector_lampWhen it comes time to change the NEC M260X projector lamp we have you covered. Follow our step-by-step guide.

How will you know the NEC M260X projector lamp needs to be replaced and is reaching end of life?

Watch for the following signs:

  • the LAMP indicator will begin to blink red
  • message on screen reads LAMP HAS REACHED THE END OF ITS USABLE LIFE. PLEASE REPLACE THE LAMP AND FILTER.
  • colour is off
  • picture is faint or has deteriorated

Checking end of projector lamp life

NEC_M260X_check_NE_NP15LP_lamp_usageTrack the life of the NEC NP15LP projector lamp with the usage time menu. The progress indicator shows the percentage of remaining bulb life:

  • Go to INFO menu
  • Scroll down to USAGE TIME to display the LAMP LIFE REMAINING and LAMP HOURS USED
  • When the lamp usage reaches 0, the Lamp Life REMAINING starts a count down from 100 hours.
  • When the count down reaches 0, the projector will turn off and not turn on.

The importance of authentic projector lamp

The first thing to do is make sure you have bought an OEM projector replacement lamp. Avoid the cheaper generic lamps with their shorter lamp life and toxic materials. You don’t want to install one and have it explode or damage the sensitive electronics in your NEC M260X projector.

Installing a generic lamp will also void your warranty. Save yourself unnecessary headaches and buy an authentic You’ll be getting a far superior product with a replacement guarantee and tech support when you buy an OEM NEC NP15LP lamp from a recognized dealer.

NOTE: Your NEC M260X projector uses the NEC NP15LP lamp. New air filters are shipped with the lamp and it’s recommended you replace them at the same time.

Find this lamp sold on Amazon by these authorized dealers:

Changing the NEC NP15LP projector lamp

Follow these important safety instructions before installing the new projector lamp

  • turn off the NEC M260X projector.
  • unplug the projector from its power source.
  • unplug the power cable.
  • wait until the projector is cool to the touch to avoid getting burned.

 

NEC_NP M311X_NEC_NP16LP_remove_projector_lamp_screwLoosen the NEC M260X projector lamp cover screw.

NEC_M260X_projector_NEC_NP16LP_remove_projector_lamp_cover

Push and slide the lamp NEC M260X projector lamp cover off.

NEC_NP M311X_remove_NEC_NP16LP_projector_lamp_screws

Loosen the two screws holding the NEC NP15LP projector lamp in place. (The screws will not come out only loosen.)

NEC_NP M311X_remove_NEC_NP16LP_projector_lamp

Remove the projector lamp by holding the indent and pulling up.

NOTE: Your NEC NP15LP projector lamp should be properly recycled. These lamps contain mercury and can’t be placed into common garbage.

NEC_M260X_projector_install_new_NEC_NP16LP_projector_lampInstall a new projector lamp housing into the NEC M260X projector by gently pressing the lamp housing into the socket. Take care not to touch the actual bulb as your finger prints can leave oil marks that burn black marks onto the bulb.

NEC_M260X_projector_tighten_NEC_NP16LP_projector_lamp_screws

Push the top center on the projector lamp to secure it. Tighten the screw on the projector  lamp.

NEC_M260X_projector_replace_projector_lamp_cover_NEC_NP16LP_projector_lamp

Reattach the  NEC M260X lamp cover by sliding the cover until it snaps into place. Tighten the screw on the lamp cover.

Replacing the filters

There are four filters in the NEC M260X projector:

  • Honeycomb hard filter – large and small
  • Accordion soft filter — large and small

Replace all four filters at the same time. Before replacing the filters wipe off any dust and dirt that came loose from the old filters. NOTE: The filters are made with two different types of material in the membrane. Both perform the same.

 

NEC_M260X_projector_NEC_NP16LP_remove_air_filter_after_installing_projector_lampPush the catch to release the filter and gently pull it out.

NEC_M260X_projector_NEC_NP16LP_detach_filter_cover_replacing_projector_lamp

The filter cover is fixed at six separate points in the projector. Bow the filter cover by pushing it slightly until it releases.

 

NEC_M260X_projector_NEC_NP16LP_replace_dark_filtersRemove the dark sponge filter and clean the filter unit and cover. Attach the new non-woven white material filters.

NEC_M260X_projector_NEC_NP16LP_replace_four_filters

  • Filter unit: Attach two honeycomb hard filters to the NEC M260X filter unit.
  • Filter cover: Attach the two accordion soft filters to the filter cover. Be sure to align the accordion slits with the protrusions of the filter cover.

NEC_M260X_projector_NEC_NP16LP_attach_filter_cover

Attach the filter cover back to the filter unit. Align the filter until with the filter cover and push the protrusions into place.

Make sure all the six mounting points are aligned properly.

NEC_M260X_projector_NEC_NP16LP_attach_filter

Insert the two catches of the top of the filter into the groove of the cabinet.

Push the filter until it clicks into place.

Reset the projector lamp timer

Once the NEC NP15LP projector lamp and NEC M260X projector air filter have both been replaced you will need to reset the timer for both. You want the projector to be able to accurately track the lamp life.

 NEC M260X projector_NEC_NP16LP_lamp_timerClear usage hours and reset hours

  • Plug in the power cored into the wall outlet.
  • Turn on the projector.
  • From the MENU select RESET.
  • Choose CLEAR LAMP HOURS.
  • A confirmation message appears.
  • Select YES.

Reset the filter hours:

  • Scroll up to CLEAR Filter HOURS.
  • A second submenu will appear.
  • Select YES. Press the ENTER button.

Extending the life of the NEC NP15LP projector lamp

Get your newly installed NEC NP15LP projector lamp will last longer by choosing the ECO option. The ECO MODE increases lamp life by lowering the power consumption. There are three modes to choose from:

  • Auto Mode: 4000 hours
  • Normal: 5000 hours
  • Eco ModeL 8000 hours

Learn more tips to extend the life of the NEC NP15LP projector lamp.

Tagged with: , ,
One comment on “Installing a NEC M260X projector lamp
Join the discussion on Facebook! All your questions, answered! The Screen & Projector Group
  1. avatar Tess Soto says:

    Replaced lamp and lamp light, status light and power light remain on and projector will not turn on. Any idea why?

Leave a Reply

Your email address will not be published. Required fields are marked *

*

Time limit is exhausted. Please reload CAPTCHA.

This site uses Akismet to reduce spam. Learn how your comment data is processed.