Install a replacement Optoma DH1011 projector lamp
How to replace the Optoma DH1011 projector lamp
When the Optoma DH1011 projector lamp approaches end of life, a replacement message will flash on screen. You may also notice the picture quality starting to have poor resolution with washed out colors. Change your projector lamp immediately. The projector will not work if the lamp has burnt out or broken.
Buying the right lamp
Your Optoma HD300X projector uses the Optoma BL-FU240A.
Buy this lamp on Amazon from the following authorized dealers:
- Optoma BL-FU240A Projector Housing with Genuine Original Osram P-VIP Bulb
- Optoma BL-FU240A, UHP, 240W Projector Lamp
- BL-FU240A Optoma Projector Lamp Replacement with cage assembly. Projector Lamp Assembly with High Quality Genuine Original Osram PVIP Bulb Inside.
If you are buying over the Internet, avoid projector lamps with a low price tag for the following reasons:
- counterfeit lamps have half the life span of original lamps
- created toxic materials that can damage your health
- prone to explosions
- damage the sensitive electronics in your projectors
- when you buy copy-cat lamps you get no guarantee or refunds
- installing a generic lamp voids your projector’s warranty.
Learn 7 ways to spot a counterfeit projector lamp.
Buy this lamp on Amazon from the following authorized dealers:
- Optoma BL-FU240A, UHP, 240W Projector Lamp
- Optoma BL-FU240A Projector Housing with Genuine Original Osram P-VIP Bulb
BL-FU240A Optoma Projector Lamp Replacement with cage assembly. - Projector Lamp Assembly with High Quality Genuine Original Osram PVIP Bulb Inside.
If you are buying over the Internet, avoid projector lamps with a low price tag for the following reasons:
Installing the Optoma DH1011 lamp
Before replacing the Optoma BL-FU24 follow these important safety tips:
- Switch off the power to the Optoma DH1011 projector by pressing the Power/Standby button.
- Disconnect the power cord.
- Allow the projector to cool down for at least 30 minutes. If should be cool to the touch. These projectors run using high temperatures and you can burn yourself badly if you don’t allow the projector to cool down.
1. Use a screwdriver to undo the two screws holding the lamp cover in place. The screws on the lamp cover and the lamp cannot be removed.
2. Remove the lid and place to one side. Don’t lose the lid as the Optoma DH1011 projector will not turn back on until the lamp cover has been properly installed.
3. Remove the two screws holding the Optoma BL-FU24 in place.
Note: The used Optoma BL-FU24 lamp contains mercury and should be properly recycled. Don’t throw it into regular garbage. Please recycle this lamp.
4. Lift up the wire handle on the Optoma BL-FU24 lamp and slowly remove it from the projector.
Be careful not to bang the lamp against the projector as this may case the bulb to break. Learn how to clean up a broken lamp.
5. Remove the new Optoma BL-FU24 from its packaging. Taking care not to touch the actual bulb, lift up the handle on the new lamp and insert it gently into the Optoma DH1011 projector.
6. Tighten the two screws on the lamp.
7. Replace the lamp cover and tighten its two screws. You are now ready to reset the Lamp Replacement Timer.
Reset the Lamp Replacement Timer
The Optoma DH1011 projector has an automatic lamp timer that tracks the numbers of hours left in the lamp. If you don’t reset the lamp replacement timer you run the risk of the lamp being used beyond its recommended life and possibly exploding in the projector.
To reset the Lamp Replacement Timer:
- Turn on the projector.
- Press MENU.
- Select OPTIONS.
- Select Lamp Settings.
- Select Lamp Reset.
- Select Yes.
- Press MENU to exit.
Tips for extending projector lamp life:
- Keep your air filters clean to avoid overheating the projector.
- Every 24 hours, turn off the projector and let it stand for 1 hour
- Make sure there is enough airflow around the Optoma DH1011 projector particularly if it’s been permanently mounted.
- Learn more with Top tips for extending DLP projector lamp life
Leave a Reply