About Us - Page 11748 of 11917 - DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP

Replace the Epson Home Cinema 8345 projector lamp

Shelagh McNallyPosted on June 8, 2017 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Use this guide to replace your Epson Home Cinema 8345 projector lamp

Watch for the signs that it’s time to replace the Epson Home Cinema 8345 projector lamp:

The projector image gets darker and starts to deteriorate.
The projector lamp flashes red.
The warning message REPLACE THE LAMP appears on screen.

A replacement warning message will also appear on screen. You can expect 4000 hours of lamp from the lamp depending on the settings and usage. You’ll need model Epson ELPLP49.

Find this authentic lamp on Amazon sold by these authorized dealers:

Installing a new Epson Home Cinema 8345 projector lamp

Before installation:

Turn power button off wait for light to stop flashing
Turn off power switch on the back of the Epson Home Cinema 8345 projector
Unplug the power cord
Allow the Epson Home Cinema 8345 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

1. The lamp cover for the Epson Home Cinema 8345 projector is found on top of the projector. Take the screwdriver that came with the projector and put it into opening on the lamp cover to release the cover switch. Remove the lamp cover.

2. Remove the two screws on either side of Epson Home Cinema 8345 projector lamp. Place the screws to either side.

3. Pull the lamp out using the top handle. Be sure to pull it out straight. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP49 contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

4, Take the new Epson ELPLP49 lamp by the handle and gently put it into place making sure the lamp is facing in the right direction.

5. Replace the Epson ELPLP49 screws on the newly installed lamp.

6. Re-connect the lamp cover. Tighten the screws on the cord and turn on the projector.

Reset the Epson Lamp Timer

Reset the Epson Home Cinema 8345 projector Lamp Replacement Counter only when the Epson ELPLP49 lamp has been replaced.

Turn the Epson Home Cinema 8345 projector projector on.
Press MENU to display the configuration menu.
Press the down arrow to move down the menu to the Reset option.

Press Enter to enter the Reset Menu.
Press the down arrow to move down the menu to the Reset Lamp Hours option.
Press Enter.

When the Reset Lamp Hour option has been chosen the Reset Lamp Hours message will appear.
Use the cursor to move to the YES option.
Press Enter to reset the lamp hours to zero

Prolong the life of the Epson ELPLP49 lamp:

Extend the life of the newly installed Epson ELPLP49 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson EMP-7500 and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life

Protect your projector with original lamps

Only genuine a Epson ELPLP49 genuine projector lamp should be used in order to keep your Epson Home Cinema 8345 projector in good working order. An OEM projector lamp has been manufactured to meet the specifications of the Epson Home Cinema 8345 projector.

Knock-off lamps may seem like a bargain due to their low prices but these counterfeit lamps can damage the sensitive and expensive mechanisms in your Epson Home Cinema 8345 projector. They are also prone to explosions and actually have a much shorter working life that authentic lamps due to the inferior materials used during their production. Even more troubling are the toxic, carcinogenic materials you are exposed to after installing one of these generic lamps.

Learn the 7 Ways to spot a counterfeit lamp.

Install a new Sony VPL-VW50 projector lamp

Shelagh McNallyPosted on June 5, 2017 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Sony VPL-VW50-projector-lamp

Instructions to replace the Sony VPL-VW50 projector lamp

Our guide shows you how to install a replacement Sony VPL-VW50 projector lamp with easy step-by-step instructions.

Buy authentic

Don’t settle for anything but the best for your Sony VPL-VW50 projector and install an authentic projector lamp. Don’t get caught with a counterfeit lamp. They have shorter lamp and are more toxic due to the substitute materials used by counterfeit manufacturers. Fake lamps won’t work properly with the sensitive electronics in your projector and are prone to explosions. Keep your projector working properly and invest in an authentic projector lamp.

Find this lamp on Amazon sold by these authorized dealers:

When to replace?

When the this Sony VPL-VW40 projector lamp projector lamp is reaching end of life, the Lamp/Cover light will continue to flash red in 3 second intervals. The message “Please replace the Lamp/Filter” will also start flashing on screen. If the projector lamp dims or the color looks strange, change it immediately. Sony recommends replacing the air filter at the same as replacing the lamp.

Replacing the Sony VPL-VW40 Lamp and Air Filter

Before installations preparations:

Unplug the AC power cord on the Sony VPL-VW50 projector.
Your Sony VPL-VW40 projector uses the Sony LMP-H200 projector lamp. Before installing the lamp, let the projector cool for at least 40 minutes. It should be cool to the touch. Don’t rush the cooling as these projectors operate using extremely high temperatures and you run the risk of a serious burn.
The projector lamp cover is on the bottom of the projector so you will need to turn it over. Put down a soft cloth on a flat surface to prevent the projector getting scratched. Turn the projector over gently. Don’t lean on the projector and make sure the surface is flat and stable.
Using a Philips screwdriver, loosen the screw holding the projector lamp cover in place. Slide the projector lamp cover. Put it to one side.

Sony-VPL-VW50-projector_Sony-LMP-H200_remove_lamp

Loosen the 3 screws on the Sony LMP-H200 lamp using a Phillips screwdriver. Grab the wire handle on the Sony LMP-H200 projector lamp and gently pull the lamp straight out. Take care not to bang the lamp as you can cause the bulb to break.

NOTE: The Sony LMP-H200 projector lamp contains mercury and should not be thrown into regular garbage. Recycle this lamp!

To finish the projector lamp installation:

Remove the packaging from the new Sony LMP-H200 projector lamp.
Lift up the handle and slowly lower the Sony LMP-H200 projector lamp into the projector.
Push it in securely until it reaches the end.
Tighten the three screws on the lamp.
Also don’t touch the actual bulb in the new lamp as oily fingerprints can burn a black spot on the lamp when it heats up.
Slide the lamp cover back onto the Sony VPL-VW50 projector.
Close the projector lamp cover and tighten the screws.
Remember to install the lamp cover properly as the projector will not turn on if the cover is loose or not installed correctly.

Replacing the Sony VPL-VW50 air filter

Sony-VPL-VW50-projector_Sony-LMP-H200_remove_air_filter_cover

Remove the filter holder. The air filter will be inside the holder. Don’t touch the fan inside as this can damage the projector.
Remove the old Sony VPL-VW50 filter and put it to one side. Attach the new air filter so that is fits into the 10 claws properly on the holder.
Aligning the air filter with the shape of the filter holder will make it easier to install.
Be sure to put the air filter holder back into the projector aligned up properly. If not, the projector will not turn back on!
Wipe off any dust from the ventilation intake holes using a soft cloth. Put the projector back in its original position

Resetting the Sony VPL-VW50 projector lamp timer

To reset the projector lamp timer, plug the AC power cord back into Sony VPL-VW50 projector.
Using the remote, scroll down to the Setup Menu.
Press Enter.

Sony_VPL-VW40_projector_LMP-H200_lamp_replacement_message

A Lamp Setting message will appear asking you if the projector lamp has been replaced.
Click on Yes.

Sony_VPL-VW40_projector_LMP-H200_Final_lamp_replacement_message

You will see a confirmation message and the Projector Lamp Timer will be automatically reset to zero.
You can see the number of hours left on your lamp by going to the Information Menu.

You can extend the life of the Sony LMP-H200 projector lamp by always making sure the filter is clean and there is enough airflow around the projector. Learn how to get a longer projector lamp life with top tips for extending DLP projector lamp life.

Tagged with: authentic lamp, Sony LMP-H200 projector lamp, Sony VPL-VW50 projector lamp, Sony VPL-VW50 projector.

Replace the Smartboard UNIFI 55 projector lamp

Shelagh McNallyPosted on June 1, 2017 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Smartboard_UNIFI55_projector

Follow this replacement guide for a new Smartboard UNIFI 55 projector lamp.

When the projected image gets darker or starts to deteriorate then it’s time to replace the Smartboard UNIFI 55 projector lamp.

Go with authentic

An authentic projector lamp makes all the difference in keeping your Smartboard UNIFI 55 projector working. If the price is too good to true, then you should avoid the lamp. Bargain basement prices mean problems down the road. Scroll down to see more reasons to avoid counterfeit lamps.

Find these lamp on Amazon sold by these authorized dealers:

<br />

When to replace

Smartboard_UNIFI 55_Smartboard_ 20-01032-20_ projector_lamp_warning

When the Smartboard UNIFI 55 projector lamp is reaching end of life you’ll see the warning message appear on screen. Replace the lamps immediately when this message shows up and don’t try to extend the use of the lamp or you may cause the lamp to explode and damage the projector.

Changing the Smartboard projector lamp

Your Smartboard UNIFI 55 projector uses the SmartBoard 20-01032-20 projector lamp.

Important Safety tips BEFORE replacing the projector lamp:

Close the projector lens door to prevent scratching or touching of the lens.
Press the power button twice on the ECP (extended control panel) or on the remote to put the system in Standby mode.
Turn off the power switch and disconnect the power cord and all connected cables.
This projector operates under high temperature and there is a burn risk so be sure to wait at least one hour minutes for the projector’s housing to completely cool.

Step 1: Remove the projector from the boom

Smartboard_UNIFI 55_Smartboard_ 20-01032-20_ projector_lamp_cover

Before you can replace the projector lamp, you must remove the projector from

the boom. You’ll need two people to do this.

Ensure that you remove the projector’s plastic lens cover.

Remove the cable cover and disconnect all cables from the Smartboard UNIFI 55 projector.

To remove the projector from the mount, hold t Smartboard_-885i4_Smartboard_-20-01032-20_-remove_projector_mount he projector and without applying pressure, remove the screw holding the cable cover in place. Lift the cover off.

If you use a projector padlock, make sure that you remove it from the locking loop.

Smartboard_UNIFI 55_Smartboard_ 20-01032-20_ projector_lamp_mount

If you need access to the projector locking

screw, loosen the wingnut and slide the

projector all the way back, away from your interactive whiteboard’s screen, and

then re-tighten the wingnut.

Loosen the wing nut and slide the Smartboard UNIFI 55 projector away from the interactive whiteboard screen. Then remove the single screw on the bracket.

Smartboard_UNIFI 55_Smartboard_ 20-01032-20_ projector_lamp_remove_mount

Take care as the projector will be loose once the screw on the mount have been loosened. Have the second person ready to hold the projector.

Using two hands carefully unhook and remove the projector from the projector boom. Lay the Smartboard UNIFI 55 projector boom flat with the warning lights facing upwards.

Step 2: Remove the old lamp

Smartboard_885i4_Smartboard_20-01032-20_remove_projector_lid-2

Smartboard_880i4_Smartboard_20-01032-20_remove_projector_lid-3 Pull off the outer lamp cover with the your finger and set it aside.

Loosen the two screws holding the SmartBoard 20-01032-20 projector lamp in place.

Press on the tab and pull up with the handle on the old lamp. Release the tab. NOTE: The SmartBoard 20-01032-20 projector lamp contains mercury and should properly recycled and NEVER thrown into regular garbage

Remove all packaging from the new SmartBoard 20-01032-20 projector lamp. Press the tab, put the new lamp into the lamp slot, and push it all the way down. Release the tab.

Put the outer lamp cover back into its original position. Align the cover and tighten the screws until the outer Smartboard UNIFI 55 projector lamp cover is secure.

Tighten the two lamp screws on the SmartBoard 20-01032-2

Replace the projector plate assembly on the projector boom

You will need two people to do this.

Smartboard_885i4_Smartboard_20-01032-20_replace_projector_mount

Using both hands, left the projector and align the hooks on the boom with the slots on the projector. Have someone hold the projector in place.
To place the projector back into the boom, attach the projector plate hinges into the corresponding flange hook on the projector boom.
Secure the projector to the plate with the original screw.
Replace the projector padlock.
Replace the projector cover on the top of the boom. Without applying pressure to the boom, replace and tighten the screw on the cover until it’s secure. Connect all the cables and put the cable cover back on.

Resetting the lamp timer

Your Smartboard UNIFI 55 has a built in lamp timer that tracks the life of the SmartBoard 20-01032-20 projector lamp. Whenever you change the lamp you need to reset the lamp timer back to zero.

Using the remote control, press the following buttons quickly to access the service menu: Down, Up, Up, Left, Up.
Scroll down to the Lamp Hour Reset field and press OK. Both Standard and Economy setting will be reset to zero.
Press the Menu button on the remote control to make the Smartboard UNIFI 55 Setting menu appear.
Select the Lamp Hours to confirm that it’s been reset to zero.
Wait five minutes for the projector lamp to warm up.

Learn how to extend the life of your SmartBoard 20-01032-20 projector lamp with Top tips for extending DLP projector lamp life.

6 reasons to avoid generic lamps:

shorter lamp life
created with toxic materials and carcinogenic parts including Krypton-85
prone to explosions
can damage the sensitive electronics in your projectors
no safeguards to protect your eyesight
no guarantee or refunds offered.

Tagged with: authentic lamp, SmartBoard 20-01032-20, Smartboard UNIFI 55 projector lamp

Replace the Infocus IN1124 projector lamp

Shelagh McNallyPosted on May 18, 2017 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Install a replacement Infocus IN1124 projector lamp using this guide.

Replace the Infocus IN1124 projector lamp quickly by following this guide.

Why go with authentic

Buy an authentic replacement projector lamp and avoid the headaches associated with counterfeit lamps. Find the 6 most common problems associated with counterfeits at the end of this post.

Find this lamp on Amazon sold by these authorized dealers:

Infocus IN1126 Assembly Lamp with Projector Bulb Inside

<br>

Install the replacement projector lamp

Your InFocus IN1124 projector needs the InFocus SP-LAMP-076 replacement projector lamp. Follow these important safety steps BEFORE installing the replacement

Turn off the InFocus IN1124 projector and unplug the power cord.
To avoid getting burned, let the projector fully cool before changing the lamp.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Infocus_IN1124_projector_Infocus_SP-LAMP-076_cover

Loosen the two captive screws on the lamp cover.
Remove the lamp cover.
Remove the two screws from the lamp module.
Lift the module handle up. Pull firmly on the module handle to remove the lamp module.
NOTE: The InFocus SP-LAMP-076 contains mercury and should not be thrown into regular garbage. Recycle this used lamp!

Infocus_IN1124_projector_Infocus_SP-LAMP-076_insert

Place the new lamp into the projector being sure to line it up properly. Align the lamp module with the connector and ensure it is level to avoid damage.
Make sure the lamp is sitting securely in place and the lamp connector must be
connected properly before tightening the screws.
Tighten the two screws on the lamp.
Replace the lamp cover and tighten the screws.

To reset the lamp timer:

Press MENU
Select INSTALLATION II/ ADVANCED. Press Enter
Scroll down to select LAMP HOUR RESET. Press Enter
Press the left arrow, then down arrow, then up arrow and double arrows
Press the MENU button to get back to INSTALLATION II

Tips for longer lamp life

Keep your air filters clean to avoid overheating the projector.
Turn off the Infocus IN1124 and let it stand for at least one hour ever 24 hours.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Top tips for extending DLP projector lamp life

Top reasons to avoid counterfeit lamps:

Buy from a legitimate source to keep your projector under warranty and working properly.

Tagged with: authentic lamp, InFocus IN1124 projector, InFocus SP-LAMP-076 replacement projector lamp

How to clean your projector lens properly

Shelagh McNallyPosted on May 10, 2017 Posted in Articles, FixYourDLP — No Comments ↓

projector_lens

Dust on your projector lens? Here’s how to clean it.

Your projector lens is similar to a camera and should be cleaned the same way. You can get everything you need to clean your projector lens at a camera store.

Before cleaning:

Turn off the projector
Unplug the power cable
Let the projector cool down. It should be cool to the touch.

Keep it clear

Avoid permanently fogging your lens. Never use alcohol or other abrasive solvents to clean your projector, especially your lens. Avoid putting lens cleaner directly on the lens as well. Both of these action will create a permanent haze giving your image a foggy look.

Proper steps

Step 1: Used compressed air or a small blower brush to remove any dust or debris from the lens. Don’t try cleaning the lens before using the compressed air or you can scratch the lens. Be sure to stand at least seven inches away from the lens . Purchase the right type of compressed air that is suitable for lens.

Step 2: If the lens is still dirty, use a camera microfiber cloth to gently wipe the lens in a circular motion staring from the center. If the lens is sticky, then put one or two drop of lens cleaning solution onto lens tissue and gently wipe the lens – again in a circular motion. You can also use a carbon-based lens using its soft brush pen to clean the lens. Avoid using rags that will leave any lint. Paper towels or tissues as the hard fibers in this material can scratch the lens while leaving particles behind.

Step 3: Let the lens dry if you have used the solution. Give another blast to compressed air to remove any dust from the cloth. Avoid touching the lens directly. Oil from your fingers will leave a mark.

Learn more about cleaning your projector:

Replace the Optoma EH500 projector lamp

Shelagh McNallyPosted on May 5, 2017 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Follow this guide to replace the Optoma EH500 projector

When it’s time to replace the Optoma EH500 projector lamp you’ll notice the picture quality is diminishing or the color appears off. The projector automatically detects the lamp life. When the lamp life is nearing the end of use, you will receive a warning message. Optoma_EH500_projector_Optoma_BL-FU310B_lamp_warning

Go with authentic

With so many choices, it can be confusing finding the correct projector lamp It’s easy to get duped into buying counterfeit projector lamp posing. The Optoma EH500 uses the Optoma BL-FU310B projector lamp. Look for the seal of approval and watch for telltale signs you are about to purchase a counterfeit lamp:

low price that seems too good to be true.
labelling that looks amateurish
Mismatched elements, glue on the edges.
Bulb that is scratched inside its cage

See below for more reasons to avoid counterfeit lamps.

Find this lamp on Amazon sold by these authorized dealers:

Installing the projector lamp

Before installing the Optoma EH500 projector lamp follow these safety precaution

Turn off the projector
Unplug the power cord
Allow the Optoma EH500 projector to cool down for at least 30 minutes. If should be cool to the touch to prevent to getting burned.

To replace the lamp

Remove the button covering the cover screw. Loosen to screw to remove the projector cover
Slide the top cover forward, and lifting the top cover off.
Remove the screw on the Optoma BL-FU310B projector lamp cover and then open it up.
Loosen the three screws from the Optoma BL-FU310B projector lamp.

Optoma_EH500_projector_Optoma_BL-FU310B_replace_projector_lamp

Raise the handle and pull out the Optoma BL-FU310B projector lamp. NOTE: The Optoma BL-FU310B projector lamp contains mercury and should not be thrown into regular garbage. Recycle this lamp.
Insert the replacement Optoma BL-FU310B projector lamp.
Tighten the four screws on the lamp.
Replace the project cover and tighten the screw.
You are now ready to reset the lamp timer.

Reset the Optoma EH500lamp timer

Your Optoma EH500 comes equipped with an automatic lamp timer that tracks the number of hours left on the projector lamp. Each time you change the lamp you need to reset the lamp timer.

Optoma_EH500_projector_Optoma_BL-FU310B_lamp_hours

Open the Options Menu from the Menu.
Scroll down to the Lamp Reset option.Press Enter.

Optoma_EH500_projector_Optoma_BL-FU310B_reset_lamp_timer

A second screen appears asking if you want to reset the lamp hours to zero. Scroll over and choose Yes. Press Enter. The lamp timer will be reset to zero.

Longer lamp life

Learn the TOP Tips for extending the lamp life in your Optoma EH500 projector lamp projector.

Reasons to avoid counterfeit lamps

Counterfeit lamps have a much shorter life
Often these lamps use toxic chemicals as substitutes
Counterfeit lamps are more prone to overheat and explode
Not properly calibrated to work with the sensitive electronics in projectors and installing can void the guarantee

Replace the Hitachi CP-X450 projector lamp

Shelagh McNallyPosted on April 29, 2017 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Install a new Hitachi CP-X450 projector lamp

Watch for these signs that indicated the Hitachi CP-X450 projector lamp is reaching its end of life:

Both the Hitachi CP-X460 Power and Lamp Indicators are flashing red while the Temp Indicator is turned off.
Color tone on the screen may also appear weak or washed out.
Picture has poor color quality.

Invest in authentic

The only replacement projector lamp that will keep your projector working is the Hitachi DT00841 (CPX401) bought from an OEM manufacturer. While knock-off lamps appear to be a bargain, they will actually end up costing you more money due to their various problems:

shorter life than original lamps
prone to explosions that can damage your projector
created with toxic substitute parts that are a health hazard
usually missing the proper safeguards to protect your eyesight from damage
no calibrated properly so damage the sensitive optics in your Hitachi CP-X200 projector

Learn to spot copycat lamps posing as authentic lamps. Keep track of projector lamp life so you’ll know when to replace the projector lamp.

Find this lamp on Amazon sold by these authorized dealers:

<br />

Installing the Hitachi CP-X450 projector lamp

Safety steps before installing the new lamp

Turn off the Hitachi CP-X450 projector.
Unplug the power cord.
Allow the projector to cool for at least 45 minutes. It should be cool to the touch. This projector works using high heat and there is danger you can be burned.
NOTE: If the projector is mounted on the ceiling, don’t stand underneath the projector while opening the cover.
Prepare the new Hitachi CP-X450 projector lamp. If the projector is mounted on a ceiling, or if the lamp has broken, contact your dealer for assistance.
Loosen the screw (marked by arrow) of the lamp cover and then slide the lamp cover to the side to remove it.
Loosen the 2 screws (marked by arrow) of the projector lamp, and slowly pick up the lamp by the handles. Be careful not the bang the lamp. The Hitachi DT00841 projector lamp contains mercury and must be recycled properly. Do not throw it in regular garbage.
Insert the new lamp, taking care not to touch the actual bulb. Oil in your fingers will cause a dark spot on the lamp when it heats up.
Tighten the two screws of the Hitachi DT00841 projector lamp that were loosened to remove the old projector lamp.
Slide the lamp cover back in place and firmly fasten the screw of the lamp cover.
Turn on the projector and set the lamp timer:

To reset the projector lamp timer:

Note: Reset the projector lamp time only when you have replaced the lamp so the Hitachi CP-X450x projector can properly track the lamp life. Otherwise you run the risk of using the lamp beyond its lamp life. HitachiCP-X450_projector_Hitachi-DT00841_projector_lamp_reset_timer

Press the MENU button
Scroll down to the GO TO ADVANCED MENU option. Press ENTER
Scroll down to the OPTION menu in the left column and press ENTER.
Scroll down to LAMP TIME. Press ENTER To make a dialogue field appear
Scroll up to the RESET option on the dialogue box.
The lamp setting will be set to zero.

Replacing the air filters

Get more hours from your by Hitachi CP-X450x keeping your air filters clean to avoid overheating the projector.

Pull the filter frame’s knob up while holding the filter cover. The filter frame will come off and the air filter will appear.
Take out the old air filter and insert the new air filter.
Put the filter frame back.
Put the filter unit back into the projector
Turn the projector on and reset the filter time using the FILTER TIME item in the EASY MENU.

Learn more with top tips for extending DLP projector lamp life.

Tagged with: authentic lamps, Hitachi CP-X450 projector, Hitachi CP-X450 projector lamp, Hitachi DT00841 projector lamp

Tips to make your projector lamp last longer

Shelagh McNallyPosted on April 19, 2017 Posted in Articles, FixYourDLP — No Comments ↓

A few simple maintenance tips can make your projector lamp last longer.

Learn how to create a simple maintenance routine that will keep your projector working at its best while prolonging projector lamp life. Here are some top tips to get you started.

Filter Cleaning

Your projector creates heat, especially from the projector lamp Every projector is cooled by fans that pull air inside. This air must pass through a filter that stops dirt and dust from getting inside the projector. When the filter gets clogged the projector can’t cool properly so overheats. When a projector runs too hot it puts stress on the circuitry and makes the lamp overheat so it wears out faster. Sometimes the lamp can explode from getting too hot. Cleaning your filter regularly is the simplest way to extend the life of your projector lamp. Follow your instruction manual to learn how to change the filter in your particular model.

Check airflow

Mounting your projector on the ceiling is a great way to save space and create a cinema-like experience. You’ll want to make sure there is enough airflow around your projector so it doesn’t overheat. If the filters can’t get enough air intake, your projector will overheat and your projector lamp won’t last as long.

Let it cool

Sudden changes in temperatures are not good for your projector lamp. Let the fans run for at least two minutes before switching it off. Suddenly turning off the projector puts the projector under too much pressure.

Don’t be trigger happy

Turning your projector constantly on and off creates a power surge that will make your projector wear out faster. It puts unnecessary stress on the projector lamp as well since it’s heating and cooling constantly. If you plan to use the projector throughout the day, let it go into sleep mode. A good rule to follow is for every 24 hours of use give it a 2-hour rest period.

Go Green

More and more projectors are coming equipped with a power saver mode sometimes called Eco Mode. It lowers the amount of light used and extends the life of your projector lamp. Running in Eco Mode is perfect for viewing in a dark room since you don’t need as much light. Without having to use maximum brightness, the life of the projector lamp is extended sometimes upwards of an extra 1,000 hours or more. Eco Mode also gets your projector to run quieter.

Watch the lamp life

Every projector has a built in timer to track lamp life. Most projectors will give you a status update when it’s time to replace the projector lamp. Be sure to pay attention to these warnings. Never reset the lamp time without changing the projector lamp as this can make the lamp work beyond it’s ended use and possible explode. Change the lamp immediately when your projector prompts you. Projector lamps tend to gradually get dimmer as they approach end of life so watch for that sign as well.

Hands off

Never touch a hot lamp or you can end up with one nasty burn. Never touch a cool lamp bulb either since the oil from your skin leaves a residue on the glass. Once the lamp heats up the oil residue will burn, creating a black spot on the lamp that shows up on the screen. A large enough oil spot can cause the lamp to shatter.

Invest in the right lamp

When it’s time to change your lamp be sure to buy from a recognized OEM manufacturer. These dealers will offer you a variety of safe options for projector lamps to suit your budgets and needs as well as a guarantee.

Save

Tagged with: authentic lamp, projector maintenance

Install a replacement NEC NP1000 projector lamp

Shelagh McNallyPosted on April 10, 2017 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

How to install a replacement NEC NP1000 projector lamp

End of life warnings

When the NEC NP1000 projector lamp is reaching end of life you’ll see a warning message about replacing the lamp appear on screen. The LAMP INDICATOR on the projector will also start blinking red. You may also see that colors are off and the picture has become faded. When any of this signs show, replace the NEC NP310 projector lamp immediately.

The projector will turn off and go into standby mode after 2100 (up to 3100 hours in Eco mode) hours of service. If this happens, be sure to replace the lamp.

Find this lamp on Amazon sold by these authorized dealers:

AuraBeam Professional Replacement Projector Lamp for NEC NP07LP With Housing (Powered by Ushio)
AuraBeam Economy Replacement Lamp for NEC NP07LP with Housing
NEC NP07LP Replacement Lamp. REPLACEMENT LAMP F/ NP300 NP400 NP500 NP600 NP500W NP610 NP610S PJ-LMP. 210W – 3000 Hour Normal, 4000 Hour ECO
NEC NP07LP OEM/Philips UHP Original Replacement Lamp
<br>

Invest in authentic lamps

The best type of projector lamp for your NEC NP1000 projector is an OEM authentic lamp. You’ll need model NEC NP01LP.

While counterfeits appear of be a bargain they often end up costing more in the long run since they are prone to explosions and have a much shorter lamp life. The other concerns are the lack of proper safety guards for your eyesight and damaging the sensitive electronics in your NEC NP1000 projector.

Changing the projector lamp

NEC_NP1000_projector_NEC-NP01LP_replacement_lamp

Follow these important safety instructions before installing the new NEC NP01LP projector lamp

- turn off the NEC NP1000 projector.
- unplug the projector from its power source.
- unplug the power cable.
- wait until the projector is cool to the touch to avoid getting burned.

Push and pull to remove the lamp cover.
Loosen the two screws holding the NEC NP07LP projector lamp in place. (The screws will not come out only loosen.)
Remove the projector lamp by holding the indent and pulling up. Take care not to knock the bulb against the projector as this may cause it to break.

NEC_NP1000_projector_NEC-NP01LP_install_new_lamp

Insert a new lamp housing gently pushing until the lamp housing is plugged into the socket. Take care not to touch the actual bulb as your finger prints can leave oil marks that burn black marks onto the bulb.
Secure it in place with the two screws.
Be sure to tighten the screws.
Re-attach the NEC NP1000 lamp cover. Tighten the screw. You are ready to reset the lamp timer

Reset the lamp timer

NEC_NP1000_projector_reset_NEC-NP01LP_lamp_timer

Once the NEC NP01LP projector lamp has been replaced you’ll need to reset the timer back to zero so the . You want the NEC NP1000 projector to be able to accurately track the projector lamp life. To reset:

Plug in the power cord into the wall outlet.
Turn on the projector.
From the MENU select RESET.
Choose CLEAR LAMP HOURS. A confirmation message appears.
Select YES.

Extending the projector lamp life

Keep your air filters clean to avoid overheating the projector.
Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours
Learn more with Top tips for extending DLP projector lamp life.

Tagged with: authentic lamp, NEC NP01LP projector lamp, NEC NP1000 projector

Get your laptop connected to your projector

Shelagh McNallyPosted on April 5, 2017 Posted in Articles, FixYourDLP — No Comments ↓

Get connected with our guide

Whether it’s a PC or Mac, getting your laptop connected to a projector or a TV depends on getting the right cable. The age of your computer will determine which kind of cable your need.

This guide shows the choices out there from the newest to the oldest.

Display Port

DisplayPort_connector Display Port is a digital display interface found on many PC laptops used to connect a video source to a display device – usually a computer monitor to a projector or TV screen.

It’s able to transit an audio and video signals from 144Hz up to 4K. It can also separate the signals to transmit only video or only audio. The video displays between 6-bit up to 16-bit color and the audio broadcasts between 8 to 24 channels. It is NOT compatible with DVI, HDMI or analog VGA without the use of an active adapter to convert the signal.

DVI

DVI-connector Digital Visual Interface (DVI) is a video connection found on some older PC laptops and on many desktop computers and is used to display 144Hz to 1080p resolution. A DVI connector is usually needed to connect a computer to any LCD TV. This interface has been designed to transmit uncompressed digital video so is often compatible with the older VGA interface and often found on DVD players. There are three different cable types:

DVI-A: analog only
DVI-D: digital
DVI-I: analog and digital

HDMI

High-Definition Multimedia Interface (HDMI) has quickly become the industry standard. It the one-cable solution since it’s able to carry uncompressed video and audio works into most multimedia devices such as computer monitors, video projectors, digital TVs or audio devices.

HDMI is found all newer PC laptops and older Macbooks and is still considered the best TV to PC connector. HDMI is only compatible with DVI with a special adapter to transmit video properly.

There are different versions of HDMI cables:

HDMI 1.0: Type A – Standard has a 19 pin connector . Reliably transmits 1080i or 720p video. Standard HDMI Cable with Ethernet allows for a dedicated data channel for device networking.
HDMI 1.0 Type B – Extended Pin has a 29 pin connector. Reliably transmits 1080i or 720p video
HDMI 1.0 Type C – Mini is used to smaller connections to portable equipment and is 40% smaller.
HMDI 1.4: Bandwidth maximum of 10.2 Gbps/s which is suitable for most smart TVs. It displays 8-bit colour and transmits 1080i or 720p video. A micro version was introduced for smart phones to display HD video.
HMDI 2.0: Needed to display any 4K high definition images. It has a bandwidth at 18 Gbps/s and transmits 10-bit or 12-bit color. Also known as the High Speed HDMI Cable

Thunderbolt

I_Thunderbolt_vs_Thunderbolt3_TM_v1 Thunderbolt is the hardware interface that is installed on all newer MacBooks and iMacs.

Thunderbolt 1 and Thunderbolt 2 use a Mini DisplayPort (MDP) while Thunderbolt 3 uses USB Type-C–currently considered the best laptop connection. You’ll need an adapter to connect to a TV or projector.

Versions 1 and 2 (photo 1) both use one type of connector while Version 3 (photo 2) has slightly larger cable.

VGA

A Video Graphics Array (VGA) is type of connector found on older desktop computers monitors, older laptop computers and early HD TVs.

You’ll recognize it by the bulky three-row, 15 pin connector although a small mini-VGA port was sometimes used in place of the full-sized VGA connector.

It’s has been phased out and replaced by the compact HDMI and DisplayPort interface.

Tagged with: Display Port, DVI, HDMI, laptop to projector, Thunderbolt, VGA