About Us - Page 131 of 177 - DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP

Your easy guide for replacing the Sanyo PLC-XU25 projector lamp

Shelagh McNallyPosted on April 24, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Sanyo PLC-XU25 projector

STEP-BY-STEP INSTRUCTIONS FOR PLC-XU25 LAMP REPLACEMENT

If your projector Sanyo PLC-XU25 lamp no longer turns on, it needs to be replaced. If the picture is dim or looks unnatural the Sanyo POA-LMP55 (service part no 610 309 2706) is reaching its end of life.

If the Replace Lamp Indicator light on the front panel is blinking orange, you must replace the Sanyo POA-LMP55 immediately. Follow our simple step-by-step instructions to replace your lamp in the Sanyo PLC-XU25 projector easily.

Sanyo PLC-XU25 warning light

Replace the Sanyo POA-LMP55 (610 309 2706) immediately with a guaranteed authentic lamp. Be sure to verify that your lamp is authentic and buy from an authorized manufacturer.

If the price of the lamp you’re about to buy seems like an incredible bargain, chances are it’s counterfeit and has been created using inferior parts that can damage the highly sophsticated componenbts in your Sanyo PLC-XU25 projector since it will not fit properly. Buying a knock-off lamp will also void your warranty and should anything happen to the projector you will not be covered.

Before installation

Allow the Sanyo PLC-XU25 projector to thoroughly cool before changing the lamp. Turn off the projector, unplug the AC cord and allow 45 to 60 minutes for the projector to cool. These projectors operate under high heat and there is a possibility of being burned, if the projector is not fully cooled before changing the Sanyo POA-LMP55 (service part no 610 309 2706) lamp.

Replacing the Sanyo POA-LMP55 (610-309-2706) Lamp Assembly

Turn off the Sanyo PLC-XU25 projector.
The lamp cover for the Sanyo PLC-XU25 projector is located at the bottom of the projector. Gently turn over the projector onto its side and loosen the screw holding the cover in place. Place the cover to one side.
Inside you’ll find the Sanyo POA-LMP55 (service part no 610 309 2706) lamp cage. Loosen both screws holding the lamp cage in place. Grab the lamp handle and gently lift the lamp out of its socket. Place to one side. Be sure to dispose of the lamp properly through a local recycling program.
Taking the new Sanyo POA-LMP55 (6103092706) lamp cage by the handle—avoid touching the actual bulb a this can break or damage the lamp. Without forcing the lamp, place it into the slot.
Once the lamp is in, tighten both screws on the Sanyo POA-LMP55 Lamp Assembly. Make sure the screws have been tightened properly or the Sanyo PLC-XU25 projector will not turn on.
Replace the Lamp Cover and tighten the screw. Re-connect the power cord and turn on the Sanyo PLC-XU25 projector. If the Sanyo POA-LMP55 (610-309-2706) lamp does not turn on after the warm-up period, try re-installing the lamp. Reset the Lamp Counter Screen by following the instructions below.

NOTE: Your old Sanyo POA-LMP55 (service part no 610 309 2706) lamp should be properly recycled. These lamps contain mercury and can’t be placed into common garbage.

RESETTING THE LAMP REPLACE COUNTER

In order for the projector to properly track the lamp life of your newly installed Sanyo POA-LMP55 (service part no 610 309 2706)you’ll need to reset the Lamp Replace Counter on the Sanyo PLC-XU25. Failure to do so can result in the Replace Lamp Indicator not tracking the lamp life properly.

Press SELECT (rear click) to have the SETTING DISPLAY screen appear.
Press the POINT DOWN button and a red arrow shows up on screen.
Using the POINT UP/DOWN button, select the LAMP PAGE and then press SELECT.
You’ll see the message “Lamp replace counter reset?“
Move the arrow to YES and press SELECT.
OK is shown for confirmation. Press YES and then the SELECT button.
Move the arrow QUIT and press SELECT to exit the MENU and return to the screen.
Your newly installed Sanyo POA-LMP55 (service part no 610 309 2706) should last between 1,000 to 2,000 hours depending on usage and maintenance.

EXTEND THE LIFE OF THE POA-LMP55 LAMP

Make your newly installed Sanyo POA-LMP55 (service part no 610 309 2706) last longer:

Wait at least five minutes before turning the Sanyo PLC-XU25 projector off.
Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP55 (service part no 610 309 2706) and prevent the Sanyo PLC-XU25 from overheating.

Tagged with: authentic lamps, authentic projector lamps, genuine lamps, genuine projector lamps, lamp, Lamp replacement, lamps, philips, Projector LAMP, replacement lamps, replacement projector lamps, Sanyo PLC-XU25, Sanyo POA-LMP55 (610 309 2706), Sanyo POA-LMP55 (service part no 610 309 2706)

Replace your Sanyo PLC-SL20 in 3 easy steps

Shelagh McNallyPosted on April 23, 2012 Posted in FixYourDLP, Philips Lamps, Projector Lamp Replacement Guides, Projectors — No Comments ↓

Sanyo PLC-SL20 projector

Follow our easy 3-step guide to a new Sanyo PLC-SL20 projector lamp.

Signs you need to replace the Sanyo POA-LMP65 (service parts no 610 307 7925) in the Sanyo PLC-SL20 projector:

1. The Replace Lamp Indicator on the top of the projector is blinking yellow.
2. The screen of the Sanyo PLC-SL20 looks dim.
3. The picture coming from the projector looks unnatural or the color is off.When you see these signs, change the Sanyo POA-LMP65 (610 307 7925) immediately.

STEP ONE: Purchase the correct projector lamp

The lifespan of your Sanyo POA-LMP65 (service parts no 610 307 7925) lamp will vary depending on how much the projector is used and if the filters are cleaned regularly.

The best thing you can do to prolong the life of your Sanyo PLC-SL20 and save money is to invest in an original Sanyo POA-LMP65 (610 307 7925).

projector lamp. Generic lamps look like a great bargain since they are generally cheaper, however, these knock-off lamps are created with inferior materials. They are susceptible to explosions, have a shorter life span and can damage the precise components in your Sanyo PLC-SL20 projector. Installing a knock-off generic lamp also voids your warranty.

Learn more about spotting dangerous projector lamps by reading our article: 7 tips for spotting counterfeits.

Looking for a less expensive option? Are you technically saavy? Watch our step-by-step video on replacing only the Sanyo POA-LMP65 (service parts no 610 307 7925) bulb instead of the entire lamp housing.

STEP TWO: Install the Sanyo POA-LMP65 lamp

NOTE: Allow the Sanyo PLC-SL20 projector to thoroughly cool before changing the lamp. Turn off the projector, unplug the AC cord and allow 45 to 60 minutes for the projector to cool. These projectors operate under high heat and there is a possibility of being burned, if the projector is not fully cooled before changing the lamp.
The lamp cover for the Sanyo PLC-SL20 is at the bottom of the projector. Gently turn projector over and loosen the screw holding the cover in place. Place the cover to one side.
Inside you’ll find the Sanyo POA-LMP65 (service parts no 610 307 7925) lamp cage. Loosen all three screws holding the lamp cage in place.
Grab the lamp handle and gently lift the lamp out of its socket. Place to one side. Be sure to dispose of the used lamp through a local recycling program. Don’t throw this lamp into regular garbage as it contains mercury.
Taking the new Sanyo POA-LMP65 lamp assembly by the handle place it into the slot. Avoid touching the actual bulb as the oil from your fingers can burn a black spot on the lenses or you can accidentally break the bulb. Don’t force the lamp into place — it should slide into the slot easily.
Once the lamp is in, tighten all three screws on the Sanyo POA-LMP65 (6103077925) lamp assembly. Make sure the screws have been tightened properly or the Sanyo PLC-SL20 projector will not turn on.
Replace the Lamp Cover and tighten the screw. Re-connect the power cord and turn on the PLC-SL20 projector. If the Sanyo POA-LMP65 (service parts no 610 307 7925) lamp does not turn on after the warm-up period, try re-installing the lamp.
Reset the Lamp Replacement Counter following the instructions below.

NOTE: Your old Sanyo POA-LMP65 (service parts no 610 307 7925) lamp should be properly recycled. These lamps contain mercury and can’t be placed into common garbage.

STEP THREE: Reset the Sanyo PLC-SL20 Lamp Replace Counter

The Lamp Replace Counter for the Sanyo PLC-SL20 will track the correct age of your newly installed lamp and trigger the Lamp Replacement Indicator. Failure to reset the counter may result in the projector not tracking the end of life for the Sanyo POA-LMP65 (service parts no 610 307 7925) and letting the projector inadvertently use the lamp past its normal life cycle. Your Sanyo PLC-SL20 may stop working suddenly if the Lamp Replace Counter has not been properly set.

Press the MENU Button to display the MAIN MENU. Press the POINT LEFT/RIGHT button and scroll right to select SETTING.
Press the SELECT button to display the SETTING DISPLAY menu.
Press the POINT DOWN button (a red arrow will appear).
Move the red arrow to the LAMP AGE and then press the SELECT button.
The message “Lamp replace counter reset?” appears. Move the arrow down to YES and press the SELECT button.
Move the arrow to QUIT and press the SELECT button.

3 tips for extending the life of the Sanyo POA-LMP65 projector lamp

Extend the life of your newly installed Sanyo POA-LMP65 (610 307 7925) by following these helpful tips:

Wait at least five minutes before turning the PLC-SL20 projector off.
Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP65 (service parts no 610 307 7925) and prevent the PLC-SL20 projector from overheating.

Tagged with: authentic projector lamps, genuine lamps, genuine projector lamps, installation, lamp enclosure, Lamp replacement, Projector LAMP, replacement lamps, replacement projector lamps, Sanyo PLC-SL20, Sanyo POA-LMP65 (610 307 7925), Sanyo POA-LMP65 (service part no 610 307 7925)

Replacing the Sanyo POA-LMP63 (service parts no 610 304 5214) projector lamp

Shelagh McNallyPosted on April 23, 2012 Posted in Projector Lamp Replacement Guides — No Comments ↓

The Sanyo POA-LMP53 (service part no 610 303 5826) should last between 1,000 to 3,000 hours depending on how often the projector is used and whether proper maintenance is done on a regular basis.

Turning the projector off immediately before waiting without a five minute cooling off period, leaving the projector running without at least one hour of rest in a 24 hour period and letting the air filter become clogged with dust will shorten the life of the Sanyo POA-LMP53 (service part no 610 303 5826) projector lamp.

You can also expect an authentic projector lamp to last longer since it’s been manufactured with top quality materials and parts. Avoid knock-offs since they use inferior materials that can damage your projector. If the price of your lamp seems too good to be true–WALK away. The few dollars you save are not worth it since these lamps don’t last as long as the genuine lamps and can explode inside the projector.

Projectors compatible with the Sanyo POA-LMP53 (610-303-5826) projector lamp:

Sanyo PLC-SL15

Sanyo PLC-SE15

Sanyo PLC-SU25

Sanyo PLC-XU36

Sanyo PLC-SU40

Scroll down for links to step-by-step instructions on replacing the Sanyo POA-LMP53 (service part no 610 303 5826) lamps for each of these projectors.

For step-by-step instructions on replacing your Sanyo POA-LMP53 (610 303 5826) lamp, click on your model listed below:

Sanyo PLC-SL15 projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP53 (service part no 610 303 5826) projector bulb for the Sanyo PLC-SL15 projector.

Sanyo PLC-SE15, Sanyo POA-LMP53, service part no 610 303 5826

Sanyo PLC-SE15 projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP53 (service part no 610 303 5826) projector bulb for the Sanyo PLC-SE15 projector.

Sanyo PLC-SU25 projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP53 (service part no 610 303 5826) projector bulb for the Sanyo PLC-SU25 projector.

Sanyo PLC-XU36 projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP53 (service part no 610 303 5826) projector bulb for the Sanyo PLC-XU36 projector.

Sanyo PLC-XU40 projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP53 (service part no 610 303 5826) projector bulb for the Sanyo PLC-SU40 projector.

Tagged with: authentic projector lamps, genuine projector lamps, lamp, Lamp replacement, lamps, philips, replacement, replacement projector lamps, Sanyo PLC-SE15, Sanyo PLC-SL15, Sanyo PLC-SU25, Sanyo PLC-SU40, Sanyo PLC-XU36, Sanyo POA-LMP53 (service part no 610 303 5826), Sanyo POA-LMP53 610 303 5826

Your quick guide to a new Sanyo PLC-XU40 projector lamp

Shelagh McNallyPosted on April 20, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Sanyo PLC-XU40 projector

Your projector lamp has between 1,000 to 3,000 hours and when it has reached end of life the Lamp Replacement Indicator on the Sanyo XU-40 will blink yellow. When you see this yellow light this it’s time to replace the Sanyo POA-LMP53 (service part no 610 303 5826)..

BEFORE INSTALLATION: Buying the correct lamp

Invest in an authentic Sanyo POA-LMP53 (610 303 5826) and avoid the temptation to buy a cheaper priced lamp. These bargain lamps are usually counterfeit lamps and use inferior parts that can damage your projector. They may end up costing you more in the long run. Authentic lamps have been manufactured with reliable parts that work with the sensitive mechanisms in your Sanyo PLC-XU40 projector. These authentic lamps come with a guarantee and won’t make your projector’s warranty invalid. Learn more with our article 7 tips for spotting counterfeits.

REPLACING THE SANYO POA-LMP53 (610-303-5826). LAMP ASSEMBLY

1. Turn off the projector and unplug the AC cord. Allow the Sanyo PLC-XU40 projector to cool to the touch. This can take between 45 to 60 minutes. Don’t open the projector when its still hot since these machines operate under high temperatures and you can burn yourself.

2. The lamps cover for the Sanyo PLC-XU40 is at the back of the projector. Loosen the two screws holding the cover in place. Place the cover to one side.

3. Inside you’ll find the Sanyo POA-LMP53 (service part no 610 303 5826). lamp cage. Loosen both screws holding the lamp cage in place. Grab the handle on the lamp cage and gently lift the lamp out of its socket. Place to one side. Be sure to dispose of the lamp properly through a local recycling program.

4. Take the new Sanyo POA-LMP53 (610 303 5826) lamp cage by the handle—avoid touching the lamp surface as oil from your fingers can cause black spots to appear when the projector is turned on. Gently maneuver the lamp into place. Don’t force the lamp as this may damage it.

5. Once the lamp is in, tighten all both screws on the Sanyo POA-LMP53 Lamp Assembly. Make sure the screws have been tightened properly or the Sanyo PLC-XU40 projector will not turn on. Replace the Lamp Cover and tighten the screw.

6. Re-connect the power cord and turn on the Sanyo PLC-XU40. If the lamp does not turn on after the warm-up period, try re-installing the lamp. Reset the lamp hour using the Lamp Control counter found on the Setting menu.

NOTE: Your old lamp should be properly recycled. These lamps contain mercury and can’t be placed into common garbage.

RESETTING THE SANYO PLC-XU40 LAMP REPLACE COUNTER

You need to reset the Lamp replace counter so the Lamp Notification system will have the same timeline as the newly installed Sanyo POA-LMP53 (service part no 610 303 5826) lamp.

NOTE: RESET the Lamp Replac eCounter ONLY WHEN the lamp has been REPLACED.

Press the MENU Button to display the MAIN MENU.
Press the POINT LEFT/RIGHT button and scroll right to select SETTING.
Press the SELECT button to display the SETTING DISPLAY menu.
Press the POINT DOWN button (a red arrow will appear)
Move the red arrow to the LAMP AGE and then press the SELECT button.
The message “Lamp replace counter reset?” appears. Move the arrow down to YES and press the SELECT button.
The message “OK?” appears. Click on YES.
Move the arrow to QUIT and press the SELECT button.

Extend the life of the Sanyo POA-LMP53 (610-303-5826) projector lamp

Extend the life of your newly installed Sanyo POA-LMP53 (service part no 610 303 5826) by following these helpful tips:

Wait at least five minutes before turning the Sanyo PLC-XU40 projector off.
Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP53 (service part no 610 303 5826) and prevent the Sanyo PLC-XU40 from overheating.

Tagged with: authentic projector lamps, genuine projector lamps, lamp enclosure, replacement projector lamps, Sanyo POA-LMP53 (service part no 610 303 5826), Sanyo POA-LMP53 610 303 5826

Replacing the Sanyo PLC-XU45 projector lamp

Shelagh McNallyPosted on April 20, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Sanyo PLC-SU45 projector

The lifespan of your Sanyo POA-LMP63 (service parts no 610 304 5214) lamp will vary depending on how much the projector is used and if the filters are cleaned regularly.

If your projector Sanyo PLC-XU45 lamp no longer turns on, it needs to be replaced. If the picture is dim or looks unnatural the Sanyo POA-LMP63 is reaching its end of life. If the Replace Lamp Indicator light on the front panel is blinking orange, you must replace the Sanyo POA-LMP63 (service parts no 610 304 5214) immediately.

Follow our simple step-by-step instructions to replace your lamp in the Sanyo PLC-XU45 projector.

Before installation

Only genuine Sanyo POA-LMP63 (service parts number 610 304 5214) lamps should be used in order to keep your projector is good working order. Any authentic lamp you buy has been manufactured to meet the specifications of the Sanyo PLC-XU45 projector.

While knock-off lamps may seem like a bargain due to their low prices, these counterfeit lamps can damage the sensitive and expensive mechanisms in your Sanyo PLC-XU45. Your guarantee on your Sanyo PLC-XU45 projector may also become void if you replace the original with a counterfeit projector lamp.

HOW TO REPLACE THE SANYO PLC-XU45 LAMP

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

1. Underneath the Sanyo PLC-XU45 projector you’ll find the Lamp Hazard cover. Gently turn it upside down protecting the top of the project.Using a Philips screwdriver loosen the screw holding the cover in place. Put the cover to one side.

2. Remove the three screws on on the Sanyo POA-LMP63 (610 304 5214) lamp. Grab the handle on the lamp cage and gently the lamp. Place to one side. Be sure to dispose of the lamp properly through a local recycling program.

3. Take the new Sanyo POA-LMP63 (service parts no 610 304 5214) lamp cage by the handle and gently maneuver it into place.

4. Avoid touching the glass or the bulb. The lamp should slide in easily – don’t force it. Once the lamp is in, tighten the three screws on the Lamp Assembly.

5. Replace the Lamp Hazard Cover and tighten the screw.

6. Re-connect the power cord and turn on the Sanyo PLC-XU45 projector.

Resetting the Lamp Replace counter on the Sanyo PLC-XU45 Projector

Reset the Lamp Replace Counter only when the Sanyo POA-LMP63 (service parts no 610 304 5214) lamp has been replaced.

Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Make sure the Sanyo PLC-XU45 projector is turned on.
Press the Menu option to display the On-Screen Menu.
Press Point left/right button(s) to move a red frame poster to Setting Menu icon.
Press the black arrow point button to move the red framed pointer to the Setting Menu Icon.
Press Point Down button to move the red frame pointer to Lamp counter reset.
Press the Select button.
Another confirmation dialog box appears, select YES.
The Lamp box will disappear and the Lamp Replace Dialog box appears.
Select YES to reset Lamp Replace Counter.

NOTE: When you reset the Lamp Replace Counter the Lamp Replace indicator stops lighting.

Tips to extend the life of the Sanyo POA-LMP53 projector lamp

Extend the life of your newly installed Sanyo POA-LMP63 (service parts no 610 304 5214) by following these helpful tips:

Wait at least five minutes before turning the Sanyo PLC-XU45 projector off.
Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP63 (service parts no 610 304 5214) and prevent the Sanyo PLC-XU45 projector from overheating.

Save money by recycling

Looking for a less expensive but more environmentally friendly option? Want more information? Watch our step-by-step video on replacing just the Sanyo POA-LMP63 bulb instead of the entire lamp housing.

Tagged with: authentic projector lamps, genuine projector lamps, replacement projector lamps, Sanyo PLC-XU45 projector, Sanyo POA-LMP63 ( 610 304 5214), Sanyo POA-LMP63 (service parts no 610 304 5214)

D.I.Y. instructions for replacing the Sanyo PLC-SU40 projector lamp

Shelagh McNallyPosted on April 19, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Sanyo PLC-SU40 projector

The yellow blinking on the panel of your Sanyo PLC-SU40 projector is your warning that projector lamp is approaching end of life. A screen that is gradually becoming dimmer or a picture with unnatural color is also a good indication that’s time to replace the lamp.

Resist the temptation to buy a cheaper counterfeit model as this can damage the sensitive mechanisms in your projector. When you purchase an authentic projector lamp, you’re guaranteed a lamp that has been manufactured with high quality parts and one that won’t damage the sensitive mechanisms in your Sanyo PLC-SU40 projector.

Your lamp number is Sanyo POA-LMP53 (service part no 610 303 5826).

STEP-BY-STEP INSTRUCTIONS FOR REPLACING THE Sanyo POA-LMP53 lamp

Before installation: Turn off the projector and unplug the AC cord. Allow the projector to cool for one hour – it should be cool to the touch. These machines operate under high temperatures and there is a BURN DANGER unless you allow it TO COOL.

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

The lamp cover for the Sanyo PLC-SU40 lamp is located at the bottom of the projector. Gently turn the projector over. Locate the screw holding the lamp cover in place, found on the right side of the projector, alongside the ventilation holes.

Remove the three screws holding the light in place. Grab the handle on the lamp cage and gently remove the lamp. Place to one side. Be sure to dispose of the lamp properly through a local recycling program.
Take the new Sanyo POA-LMP53 (service part no 610 303 5826 lamp cage by the handle and gently maneuver it into place.
Avoid touching the glass or the bulb. The lamp should slide in easily – don’t force it. Once the lamp is in, tighten all three screws on the Lamp Assembly.
Make sure the screws have been tightened properly or the projector will not turn on.
Replace the Lamp Cover and tighten the screw.
Re-connect the power cord and turn on the Sanyo PLC-SU40 lamp projector. If the lamp does not turn on after the warm-up period, try re-installing the lamp.
Reset the lamp hour using the Setting menu.
Your old lamp should be properly recycled. These lamps contain mercury and can’t be placed into common garbage

Resetting PLC-SU40 Lamp Replacement Counter

CAUTION: Don’t operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents. Reset the Lamp Replacement Counter only when the Sanyo POA-LMP53 (service part no 610 303 5826 has been replaced.

Turn the Sanyo PLC-SU40 projector on.
Press the Menu option to display the On-Screen Menu.
Press Point left/right button(s) to Setting Menu icon.
Press Point Down button to move the red frame pointer to Lamp counter reset.
Press the Select button.
Another confirmation dialog box appears, select YES.

NOTE: When you reset the Lamp Replace Counter is reset, the Lamp Indicator will stop blinking.

Extend the life of the Sanyo POA-LMP53 projector lamp

Extend the life of your newly installed Sanyo POA-LMP53 (service part no 610 303 5826) by following these helpful tips:

Wait at least five minutes before turning the Sanyo PLC-SU40 projector off.
Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP53 (service part no 610 303 5826) and prevent the Sanyo PLC-SU40 projector from overheating.

Tagged with: authentic projector lamps, genuine projector lamps, Lamp replacement, replacement projector lamps, Sanyo PLC-SU40, Sanyo POA-LMP53 (service part no 610 303 5826), Sanyo POA-LMP53 610 303 5826

How change the Sanyo PLC-XU36 projector lamp

Shelagh McNallyPosted on April 19, 2012 Posted in FixYourDLP — No Comments ↓

Sanyo PLC-XU36 projector

Depending on usage and the regular maintenance done on your projector, your Sanyo POA-LMP53 (service part no 610 303 5826) lamp should last between 1,000 to 3,000 hours before end of life. When it`s tijme tp change the projector lamp on your Sanyo PLC-XU36 the Lamp Replacement Indicator will start flashing yellow. Replace the Sanyo POA-LMP53 (service part no 610 303 5826) immediately.

Simplify your life and buy an authentic projector lamps. It’s worth paying the few extra dollars to be guaranteed a projector lamp that will work and will keep your warranty intact. Cheaper counterfeit model can damage the sensitive mechanisms in your projector and are prone to explosions. When you purchase an authentic projector lamp, you’re guaranteed a lamp that has been manufactured with high quality parts and one that won’t damage the sensitive mechanisms in your Sanyo PLC-SU36 projector.

Six Steps to replace the Sanyo POA-LMP53 lamp

1. The lamp cover for the Sanyo PLC-SU36 lamp is located at the bottom of the projector. Gently turn the projector over. Locate the screw holding the lamp cover in place, found on the right side of the projector, alongside the ventilation holes.

2. Remove the three screws holding the light in place Grab the handle on the lamp cage and gently remove the lamp. Place to one side. Be sure to dispose of the lamp properly through a local recycling program.

3. Take the new Sanyo POA-LMP53 (service part no 610 303 5826 lamp cage by the handle and gently maneuver it into place.

4. The lamp should slide in easily – don’t force it. Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

5. Once the lamp is in, tighten all three screws on the Lamp Assembly. Make sure the screws have been tightened properly or the projector will not turn on.

6. Replace the Lamp Cover and tighten the screw. Re-connect the power cord and turn on the Sanyo PLC-SU36 lamp projector. If the lamp does not turn on after the warm-up period, try re-installing the lamp. Reset the lamp hour using the Setting menu.

Your Sanyo POA-LMP53 (service part no 610 303 5826 old lamp should be properly recycled. These lamps contain mercury and can’t be placed into common garbage.

Resetting PLC-SU36 Lamp Replacement Counter

CAUTION: Don’t operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accident. Reset the Lamp Replacement Counter only when the Sanyo POA-LMP53 (service part no 610 303 5826 has been replaced.

Turn the Sanyo PLC-SU36 projector on.
Press the Menu option to display the On-Screen Menu.
Press Point left/right button(s) to Setting Menu icon.
Press Point Down button to move the red frame pointer to Lamp counter reset.
Press the Select button.
Another confirmation dialog box appears, select YES.

NOTE: When you reset the Lamp Replace Counter is reset, the LampReplacement Indicator will stop blinking.

Extend the life of the Sanyo POA-LMP53 projector lamp

Extend the life of your newly installed Sanyo POA-LMP53 (service part no 610 303 5826) by following these helpful tips:

Wait at least five minutes before turning the Sanyo PLC-SU36 projector off.
Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP53 (service part no 610 303 5826) and prevent the Sanyo PLC-SU36 projector from overheating.

Tagged with: authentic projector lamps, genuine projector lamps, replacement projector lamps, Sanyo POA-LMP53 (service part no 610 303 5826), Sanyo POA-LMP53 610 303 5826

How to change your Sanyo PLC-SU25 projector lamp

Shelagh McNallyPosted on April 18, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Wondering when it’s time to replace projector lamp? When the Sanyo POA-LMP53 (service part no 610 303 5826)lamp is nearing end of life the Lamp Replacement Indicator on the top of the projector will blink yellow.

The first important step is to buy an authentic projector lamp. Avoid the temptation to purchase a cheaper version of the POA-LMP53 as these are often counterfeit models with less durable parts that can damage the sensitive mechanisms in your Sanyo PLC-SU25 projector. Get smart about counterfeit lamps by reading 7 tips for spotting counterfeits.

Sanyo PLC-SU25 projector

STEP-BY-STEP INSTRUCTIONS FOR LAMP REPLACEMENT

Before installation: Turn off the projector and unplug the AC cord. Allow the Sanyo PLC-SU25 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures.

Replacing the Sanyo POA-LMP53 lamp

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

1. Underneath the Sanyo PLC-SU25 projector you’ll find the Lamp Hazard cover. Gently turn it upside down protecting the top of the project.Using a Philips screwdriver loosen the screw holding the cover in place. Put the cover to one side.

2. Remove the three screws on on the Sanyo POA-LMP53 (service parts no 610 303 5826) lamp. Grab the handle on the lamp cage and gently the lamp. Place to one side. Be sure to dispose of the lamp properly through a local recycling program.

3. Take the new Sanyo POA-LMP53 (610-303-5826) lamp cage by the handle and gently maneuver it into place.

4. Avoid touching the glass or the bulb. The lamp should slide in easily – don’t force it. Once the lamp is in, tighten the three screws on the Lamp Assembly.

5. Replace the Lamp Hazard Cover and tighten the screw.

6. Re-connect the power cord and turn on the Sanyo PLC-SU25 projector.

Resetting the Lamp Replace counter on the Sanyo PLC-SU25 Projector

Reset the Lamp Replace Counter only when the Sanyo POA-LMP53 (service part no 610 303 5826) lamp has been replaced.

Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Make sure the Sanyo PLC-SU25 projector is turned on.
Press the Menu option to display the On-Screen Menu.
Press Point left/right button(s) to move a red frame poster to Setting Menu icon.
Press the black arrow point button to move the red framed pointer to the Setting Menu Icon.
Press Point Down button to move the red frame pointer to Lamp counter reset.
Press the Select button.
Another confirmation dialog box appears, select YES.
The Lamp box will disappear and the Lamp Replace Dialog box appears.
Select YES to reset Lamp Replace Counter.

NOTE: When you reset the Lamp Replace Counter the Lamp Replace indicator stops lighting.

Tips to extend the life of the Sanyo POA-LMP53 projector lamp

Extend the life of your newly installed Sanyo POA-LMP53 (service part no 610 303 5826) by following these helpful tips:

Wait at least five minutes before turning the Sanyo PLC-SU25 projector off.
Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP53 (service part no 610 303 5826) and prevent the Sanyo PLC-SU25 projector from overheating.

Tagged with: authentic projector lamps, genuine projector lamps, replacement projector lamps, Sanyo PLC-SU25, Sanyo POA-LMP53 (service part no 610 303 5826), Sanyo POA-LMP53 610 303 5826

3 steps to a new Sanyo PLC-SL15 projector lamp

Shelagh McNallyPosted on April 18, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Sanyo PLC-SL15 projector

The lifespan of your Sanyo POA-LMP53 (service part no 610 303 5826) lamp will vary depending on how much the projector is used and if the filters are cleaned regularly. When it’s time to replace the lamp, the LAMP REPLACE indicator will flash yellow.

Follow these three easy steps to install a new Sanyo POA-LMP53 (service part no 610 303 5826) in your Sanyo PLC-SL15 projector.

STEP ONE: Purchase the correct projector lamp

Protect your investment and prolong the life of your Sanyo PLC-SL15 projector by investing in an authentic Sanyo POA-LMP53 (service part no 610 303 5826) lamp. The cheaper knock-offs lamps may look like a great deal but these generic lamps are created with inferior materials. The few extra dollars you save will not be worth the trouble when these lamps explode, burn out quickly, void your warranty and damage the precise components in your Sanyo PLC-SL15 projector. Protect yourself by educating yourself about counterfeit lamps by reading 7 tips for spotting counterfeits.

STEP TWO: Install the new Sanyo POA-LMP53 lamp

The Sanyo PLC-SL15 projector should be cool to the touch before changing the Sanyo POA-LMP53 (service part no 610 303 5826) There is a danger of being burned if you open up the projector while it is still hot. Allow 45 minutes for the inside of the projector to cool.
The lamp cover for the Sanyo PLC-XT15 is located at the bottom of the projector. Gently turn projector over and loosen the screw holding the cover in place. Place the cover to one side.
Inside you’ll find the Sanyo POA-LMP53 (service part no 610 303 5826) lamp cage. Loosen the three screws holding the lamp cage in place. Grab the lamp handle and gently lift the lamp out of its socket. Place to one side. Don’t throw this lamp into the regular garbage as it contains mercury — send it to a local recycling program where it can be disposed of properly.

Taking the new Sanyo POA-LMP53 (610 303 5826) lamp assembly by the handle place it into the slot. Don’t force the lamp in and avoid touching the actual bulb since your fingerprint may leave a mark on the bulb that will become a black spot on the lamp when it heats up.
Gently slide the lamp into place and tighten all three screws on the Once the lamp is in, tighten both screws on the Sanyo POA-LMP53 (610 303 5826) lamp assembly.
Replace the Lamp Cover and tighten the screw. Re-connect the power cord and turn on the Sanyo PLC-SL15 projector If the Sanyo POA-LMP53 (service parts no 610 303 5826) lamp does not turn on after the warm-up period, try re-installing the lamp.
Reset the Lamp Replace Counter by following the instructions below.

NOTE: Your old POA-LMP53 (service parts no 610-303- 5826) lamp always should be properly recycled. These lamps contain mercury and can’t be placed into common garbage.

STEP THREE: Reset the Sanyo PLC-SL15 Lamp Replace Counter

The Lamp Replace Counter always needs to be reset after installing a new projector lamp so it can track the age of your lamp and turn the Lamp Replace indicator on when the end of life for the Sanyo POA-LMP53 (service parts no 610-303- 5826) is approaching.

Press the MENU Button to display the MAIN MENU. Press the POINT LEFT/RIGHT button and scroll right to select SETTING.
Press the SELECT button to display the SETTING DISPLAY menu.
Press the POINT DOWN button (a red arrow will appear).
Move the red arrow to the LAMP AGE and then press the SELECT button.
The message “Lamp replace counter reset?” appears. Move the arrow down to YES and press the SELECT button.
Move the arrow to QUIT and press the SELECT button.

Extend the life of the Sanyo POA-LMP53 projector lamp

Extend the life of your newly installed Sanyo POA-LMP53 (service parts no 610-303- 5826) by following these helpful tips:

Wait at least five minutes before turning the Sanyo PLC-SL15 off.
Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP53 (service parts no 610-303- 5826) and prevent the Sanyo PLC-SL15 projector from overheating.

Tagged with: authentic projector lamps, genuine projector lamps, replacement projector lamps, Sanyo PLC-SL15, Sanyo POA-LMP53 (service part no 610 303 5826), Sanyo POA-LMP53 610 303 5826

How to install your new Sanyo PLC-SE15 projector lamp

Shelagh McNallyPosted on April 17, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Sanyo PLC-SE15 projector

When you see the Lamp Replacement light turn yellow on the top of your Sanyo PLC-SE15 it’s time to replace the projector lamp.

Replace the projector lamp immediately with lamp model Sanyo POA-LMP53 (service part no 610 303 5826).

Follow our easy step-by-guide below for a hassle-free installation of your new Sanyo POA-LMP53 (610 303 5826) lamp for the Sanyo PLC-SE15 projector.

Finding the right projector lamp

Avoid hassles by investing in an original Sanyo POA-LMP53 (service part no 610 303 5826) projector lamp for your Sanyo PLC-SE15. Knock-off lamps are created with inferior materials so are susceptible to explosions, have a shorter life span and can damage the precise components in your Sanyo PLC-SE15 projector. Installing a knock-off generic lamp also voids your warranty.

Buying an authentic projector lamp guarantees a lamp created with genuine, non-hazardous materials created by the original manufacturer gives you are lamp with a warranty. These authentic lamps are built to work properly with your projector’s sensitive mechanisms. It’s worth the few extra dollars to eliminate potential problems and be have a money back guarantee. Buy an authentic Sanyo POA-LMP53 (service part no 610 303 5826) projector lamp and make life easier. Learn more about spotting dangerous projector lamps by reading our article: 7 tips for spotting counterfeits.

Installing the new Sanyo POA-LMP53 (610 303 5826) lamps

Allow the Sanyo PLC-SE15 projector to thoroughly cool before changing the lamp. Turn off the projector, unplug the AC cord and allow 45 to 60 minutes for the projector to cool. These projectors operate under high heat and there is a possibility of being burned, if the projector is not fully cooled before changing the Sanyo POA-LMP53 lamp.
The lamp cover for the Sanyo PLC-SE15 is located at the back of the projector. Turn the projector around and loosen the two screws holding the cover in place. Place the cover to one side.
Inside you’ll find the Sanyo POA-LMP53 (service part no 610 303 5826) lamp cage. Loosen the three holding the lamp cage in place. Grab the lamp handle and gently lift the lamp out of its socket. Place to one side. Be sure to dispose of the used lamp through a local recycling program. Don’t throw this lamp into the regular garbage as it contains mercury.

Taking the new Sanyo POA-LMP53 (service part no 610 303 5826) lamp assembly by the handle place it into the slot. Avoid touching the actual bulb as the oil from your fingers can burn a black spot on the lenses or you can accidentally break the bulb. Don’t force the lamp into place — it should slide into the slot easily.
Once the lamp is in, tighten all three screws on the Sanyo POA-LMP53 (service part no 610 303 5826) lamp assembly. Make sure the screws have been tightened properly or the Sanyo PLC-SE15 projector will not turn on.
Replace the Lamp Cover and tighten the screw. Re-connect the power cord and turn on the Sanyo PLC-SE15 projector. If the Sanyo POA-LMP53 (610 303 5826) lamp does not turn on after the warm-up period, try re-installing the lamp.
Reset the Lamp Replace Counter by following the instructions below.

NOTE: Your old Sanyo POA-LMP53 (service part no 610 303 5826) lamp should be properly recycled. These lamps contain mercury and can’t be placed into common garbage.

Reset the Lamp Replace Counter

The Lamp Replace Counter for the Sanyo PLC-SE15 will track the correct age of your newly installed lamp and trigger the Lamp Replacement Indicator. Failure to reset the counter may result in the projector not tracking the end of life for the Sanyo POA-LMP53 (610 303 5826) and letting the projector inadvertently use the lamp past its normal life cycle. Your Sanyo PLC-SE15 may stop working suddenly.

NOTE: RESET the Lamp Replacement Counter ONLY WHEN the lamp has been REPLACED.

Press the MENU Button to display the MAIN MENU.
Press the POINT LEFT/RIGHT button and scroll right to select SETTING.
Press the SELECT button to display the SETTING DISPLAY menu.
Press the POINT DOWN button (a red arrow will appear).
Move the red arrow to the LAMP AGE and then press the SELECT button.
The message “Lamp replace counter reset?” appears. Move the arrow down to YES and press the SELECT button.
The message “OK?” appears. Click YES.
Move the arrow to QUIT and press the SELECT button.

Extend the life of the Sanyo POA-LMP53 projector lamp

Extend the life of your newly installed Sanyo POA-LMP53 (service part no 610 303 5826) by following these helpful tips:

Wait at least five minutes before turning the Sanyo PLC-SE15 projector off.
Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP53 (service part no 610 303 5826) and prevent the Sanyo PLC-SE15 projector from overheating.

Tagged with: authentic projector lamps, genuine projector lamps, replacement projector lamps, Sanyo PLC-SE15 projector, Sanyo POA-LMP53 (service part no 610 303 5826)