We're now Screen and Projector! For updated content, visit ScreenAndProjector.com and follow @screenandproj on social media!
Home › About Us › Page 176

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Boxlight_CP-11t_projector_Boxlight_CP13T-930_projector_lampA yellow blinking light means it’s time to replace the Boxlight CP-11t projector lamp. Let our guide help you switch to a new projector lamp.

Warning messages

When the Boxlight CP-11t projector lamp is approaching end of life the  LAMP REPLACEMENT lights starts flashing yellow.
You may also notice the image becomes darker or the image color becomes unnatural. Change the projector lamp immediately.

The importance of OEM projector lamps

There are many choices being offered on the Internet and it can be tempting to purchase a generic lamp due to their low prices. However, you get what you pay for and with generics that means a long list of problems that can end up damaging your Boxlight CP-11t projector. Stick to an authentic OEM projector lamp and keep your Boxlight CP-11t  projector working at its best.

6 Reasons to avoid generics

Find this lamp sold on Amazon by these authorized dealers:

Replacing the Boxlight CP10T-930 projector lamp

Before replacing the Boxlight CP10T-930 projector lamp follow these safety tips:

  • Disconnect the power cord on the Boxlight CP-11t projector.
  • Reduce the risk of severe burns by allowing the Boxlight CP-11t projector to cool for at least 45 minutes. These projectors operate using high temperatures and you run the risk of severe burns if you don’t allow it to cool down.

Boxlight_CP-11t_projector_Boxlight_CP13T-930_replace_projector_lampPlace the projector on a soft surface and turn it over. Loosen the screw holding the lamp cover in place.

Remove the two screws holding the Boxlight CP10T-930 projector lamp in place.

Using the wire handle on the Boxlight CP10T-930 projector lamp and gently remove the lamp. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: Be sure to recycle the Boxlight CP10T-930 projector lamp as contains mercury and should not be thrown into regular garbage. Recycle it!

Insert the new CP10T-930 and avoid touching the actual bulb as this can result in black spots from the oil on your hands.

Tighten the two screws on the Boxlight CP10T-930 projector lamp . Place the cover back onto the Boxlight CP-11t projector and tighten the lamps screw. You must now reset the lamp timer.

Boxlight_CP-11t_projector_Boxlight_CP13T-930_reset_projector_lamp_timerResetting the Boxlight SP-50m lamp counter

Once the Boxlight CP10T-930 projector lamp has been replaced, you will need to reset the lamp counter so the Boxlight CP-11t projector can accurately track the number of lamp hours remaining:

  • Turn the projector on, and press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select SETTING and press the SELECT button.
  • Another dialog box SETTING MENU will appear.
  • Press the POINT DOWN button and a red-arrow icon will appear.
  • Move the arrow to Lamp age, and then press the SELECT button. The message “Lamp replace monitor Reset?” is displayed.
  • Select [Yes] to reset the Timer.
    When the Lamp Replacement Monitor Timer is reset, the LAMP REPLACEMENT indicator stops lighting.

Learn how to extend the life of the Boxlight CP10T-930 projector lamp. Check out Top tips for extending DLP projector lamp life

Interested in a green alternative?

Boxlight_CP-11t_projector_Boxlight_CP13T-930_Video_InstructionsThis projector has the option of also just replacing the actual bulb to re-use the plastic cage. This reduces waste and is a great way to green your projector. Watch our training video to learn more.

 

 

 

Tagged with: , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

BenQ _MX760_projector_5J.J3J05.001_projector_lampDon’t call the technician. Follow this easy guide to replace the BenQ MX760 projector lamp.

Warning signs for end of projector lamp

When the BenQ MX760 projector lamp is reaching end of life the lamp indicator on the projector will start flashing orange. Warning messages will also begin to appear on screen. You may notice the image deteriorating or the color looking off. To obtain the lamp hour information: BenQ-_MX760_projector_5J.J3J05.001_projector_lamp_warning

  • Press MENU/EXIT and then press / to highlight the SYSTEM SETUP: Advanced
  • Press to highlight Lamp Settings and press MODE/ENTER. The Lamp Settings page is displayed.
  • You will see the Equivalent Lamp Hour information appearing on the menu.
  • To leave the menu, press MENU/EXIT.
  • You can also get the lamp hour information on the INFORMATION menu.

Setting the projector to economic mode will extend the projector lamp life.

Find this lamp on Amazon from these authorized dealers:

Why an authentic projector lamp is crucial

Be ready to replace the lamp by first buying the correct BenQ 5J.J3J05.001 projector lamp for your BenQ MX760 projector. An authentic OEM projector lamps is the only lamp that will keep your BenQ MX760 projector working properly. Why avoid generic lamps? Here are 6 good reasons:

Replace the BenQ 5J.J3J05.001 projector lamp

Before changing the lamp:

  • Reduce the risk of electrical shock by disconnecting the power cord on the BenQ MX760 projector.
  • Reduce the risk of severe burns by allowing the projector to cool for at least 45 minutes.

BenQ-_MX760_projector_5J.J3J05_projector_lamp_remove_cover_screw

 

Loosen the screw holding the lamp cover onto the BenQ MX760 projector.

BenQ-_MX760_projector_5J.J3J05_projector_lamp_remove_cover

Lift up the cover. Remove and dispose of the lamp protection film. Do not insert your fingers between the lamp and the projector. The sharp edges inside the projector may cause injuries.

 

BenQ-_MX760_projector_5J.J3J05_disconnect_projector_lamp

Disconnect the projector lamp connector from the projector (Step #2). Loosen the screw that secures the BenQ 5J.J3J05.001 projector lamp.

BenQ-_MX760_projector_5J.J3J05_remove_old_projector_lampSlowly and gently pull the BenQ 5J.J3J05.001 projector lamp out of the projector. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The BenQ 5J.J3J05.001 projector lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps! If you bought from an authentic manufacturer they will recycle the lamp for you at no extra cost (another reason to buy authentic lamps).

 

BenQ-_MX760_projector_5J.J3J05_install_new_projector_lampInsert the new BenQ 5J.J3J05.001 projector lamp first into the connector on the projector and reconnect the lamp connector.

BenQ-_MX760_projector_5J.J3J05_tighten_projector_lamp_screw

Make sure the handle is fully locked. Tighten the projector lamp screw. If the screw is too loose or too tight, the projector may not turn on.

BenQ-_MX760_projector_5J.J3J05_projector_lamp_install_coverRe-install the BenQ MX760 lamp cover and tighten the screw. Reset the total lamp operation timer.

 

 

Reset the projector lamp counter

BenQ-_MX760_projector_5J.J3J05_reset_projector_lamp_timerWhen the BenQ 5J.J3J05.001 projector lamp in the BenQ MX760 projector has been changed the projector lamp timer must be reset:

  • Turn on the BenQ MX760 projector.
  • After the startup logo, open the On-Screen Display (OSD) menu.
  • Go to the SYSTEM SETUP.
  • Scroll over to Advanced > Lamp Settings menu.
  • Press MODE/ENTER to display Lamp Settings page is displayed.
  • Highlight Reset lamp timer. A warning message is displayed asking if you want to reset the lamp timer.
  • Highlight Reset and press MODE/ENTER. The lamp time will be reset to “0”.

Extend the life of the BenQ 5J.J3J05.001 projector lamp last longer with the following tips:

  • Keep your air filters clean to avoid overheating the projector.
  • Use the Lamp Power option on the BenQ MX760 and set to Economic Mode to reduce the amount of power used but extend lamp life.
  • Learn more with Top tips for extending DLP projector lamp life.

BenQ-MX760_projector_5J.J3J05_projector_lamp_Video_guide

Green your BenQ MX760 projector lamp

The  BenQ MX760 projector lamp has the option of replacing only the bulb in the BenQ 5J.J3J05.001 projector lamp. You re-use the plastic cage and reduce waste. You can green your projector while saving money. Our instructional video shows you how step-by-step.

 

 

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Proxima_Pro_AV_9500_projector_SP-LAMP-004_projector_lampThis guide shows you how to replace the ASK Proxima DP-9500 projector lamp in 3 easy steps.

Your ASK Proxima DP-9500 projector uses the ASK Proxima SP-LAMP-004 projector lamp. The expected ASK Proxima DP-9500 projector lamp life is approximately 1,500 hours. The length may vary depending on usage and maintenance.

To find out how much time is left on the lamp you can also check the ABOUT screen found on the MAIN Menu. It will list the number of hours used.

Switching projector lamps

Proxima_Pro_AV_9500_SP-LAMP-004_projector_lamp_indicators

 

The ASK Proxima DP-9500 projector is equipped with two projector Lamp. You can switch between using one or two lamps. Use one lamp to extend the life of the projector lamp.
To change over Lamp Mode:
1. Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to select SETTING and press SELECT button. Setting dialog box appears.
2. Press POINT DOWN button to move a red frame pointer to “Lamp mode”.  Set “2 lamps mode” or “1 lamp mode” by pressing POINT LEFT/RIGHT button(s). When Lamp Mode is set from “2 lamps mode” to “1 lamp mode” image becomes little darker. When Lamp Mode is set from “1 lamp mode” to “2 lamps mode” image become brighter gradually.

Step 1: Finding the right projector lamp

There are so many choices on the Internet for a Ask Proxima SP-LAMP-004 projector lamp that finding the correct lamp can be overwhelming. Go with authentic OEM lamps and ignore the sites offering generic “compatible” projector lamps even though the prices seems to be a bargain.

This generic lamps are made with counterfeit materials and are prone to explosions, offer poor picture quality and actually have a shorter lamp life than authentic projector lamps. Installing generic lamps into your ASK Proxima C300HB projector will void the warranty leaving you unprotected should any of the sensitive components inside be damaged due to the inferior workings of these lamps. More importantly, these “compatible” lamps are often made with toxic materials such as the carcinogenic Krypton-85.

Protect your investment and your health. Reduce hassles and problems. Buy an authentic ASK Proxima SP-LAMP-004 projector lamp.

Find this lamp sold on Amazon by these authorized dealers:

Step 2: Know when to replace the projector lamp

Proxima_Pro_AV_9500_SP-LAMP-004_projector_lamp_statusWhen the ASK Proxima SP-LAMP-004 needs to be replaced you will see the lamp replace indicator will flash yellow. You may noticed the picture start to dim or the colors appear off.

Look for a change on the lamp indicator;

  • Yellow Lamp: Projection Lamp lights normally.
  • Dim Lamp: Projection Lamp is turned off.
  • Red Lamp: Projection Lamp is nearing its end. When image becomes darker or color becomes unnatural, replace lamp. (LAMP REPLACE indicator lights yellow.)
  • X Mark on Lamp: (LAMP REPLACE indicator flashes yellow.) Projection lamp is defective or fails to be turned on. Restart a projector on, and make sure lamp is on. If this mark still appears, replace lamp corresponding with number marked X.

Step 3: Installing the ASK Proxima SP-LAMP-004 projector lamp

Before installing the ASK Proxima SP-LAMP-004 projector lamp:

  • Let the ASK Proxima DP-9500 cool down to avoid burning yourself. It should be cool to the touch.
  • Unplug the AC cord.

Proxima_Pro_AV_9500_SP-LAMP-004_replace_projector_lamp1. The lamp cover will be found at the back of the ASK Proxima DP-9500 projector. Loosen the two screws holding  ASK Proxima SP-LAMP-004 projector lamp in place. Remove and place to one side.
2. Loosen the two screws holding the ASK Proxima SP-LAMP-004 projector Lamp Assembly in place.
3. Grab onto the ASK Proxima SP-LAMP-004 projector lamp handle and pull the lamp from the projector. Place to one side. Be sure to dispose of the used lamp through a local recycling program. Don’t throw this lamp into the regular garbage as it contains mercury.

The ASK Proxima SP-LAMP-004 projector lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

4. Place the new ASK Proxima SP-LAMP-004 projector lamp into the socket being careful not to touch the bare lamp (this can form black spots on the bulb that will ruin the projected image).
5. Tighten the two screws holding the ASK Proxima SP-LAMP-004 projector lamp Assembly in place.
6. Put the ASK Proxima DP-9500 cover back in place and tighten the two screws.
7. Put the power cord back into the projector and turn it on. You are now ready to Reset the Lamp Replace Counter.

Resetting the projector lamp timer

It’s important to reset the projector lamp timer of the ASK Proxima DP-9500 in order to properly track lamp life. Failure to reset the timer may result in the projector not knowing when the lamp is finished and shutting down suddenly.

To reset the projector lamp timer:

Be sure to reset Lamp Counter when Lamp Assembly is replaced. When Lamp Replace Counter is reset, LAMP REPLACE indicator stops lighting.

Proxima_Pro_AV_9500_SP-LAMP-004_reset_projector_lamp_timer_screen2

  • Turn projector on, press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button(s) to move a red frame pointer to SETTING Menu icon.
  • Press POINT DOWN button to move a red frame pointer to “Lamp counter reset” and then press SELECT button.
  • Move arrow to replaced lamp number (Lamp 1 orProxima_Pro_AV_9500_SP-LAMP-004_reset_projector_lamp_timer_screen1 Lamp 2) and then press SELECT button. Message “Lamp replace counter Reset?” is displayed. Move pointer to [Yes] and then press SELECT button. Move pointer to Lamp counter reset and thenpress SELECT button.
  • Another confirmation dialog box appears and select [Yes] to reset Lamp Replace Counter. Do not reset Lamp Replace Counter except after Projection lamp is replaced.
  • Be sure to replace the procedure for both lamps.

Learn more: Top tips for extending DLP projector lamp life.

The green projector lamp

ASK_Proxima_Pro_AV_9500_training_video

The ASK Proxima DP-9500 projector has the option of  just replacing the actual bulb and re-use the plastic cage. This reduces waste and is a great way to green your projector.

Watch our training video to learn more.

Tagged with: , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Acer_XD1250P_projector_ACER EC.J2101.001_projector_lampSwitching from an old to a new Acer XD1250P projector lamp is simple and quick when you use our step-by-step guide.

Be prepared with an authentic projector lamp

Your Acer XD1250P projector uses the Acer EC.J2101.001 projector lamp. Be sure to buy your Acer XD1250P projector lamp from an authorized dealer to keep your Acer XD1250P projector working properly. Cheap knock-offs will damage the sensitive optics in your XD1250P projector and have a much shorter life span. These knock off projector lamps are also created with toxic materials that pose a health threat. Authentic OEM are less likely to explode and come with a money-back guarantee as well as keeping your warranty intact. Protect yourself from buying counterfeit lamps.

End of life warning signs

You can expect the Acer EC.J2101.001 projector lamp to last 2000 hours on Standard mode and 3000 hours on Eco mode. (You can turn Eco Mode on or off from the Management menu.) Track the lamp life for the Acer EC.J2101.001 projector lamp on the Managment menu under Lamp Hour Relapse.

Watch for the warning message that will flash on screen indicating its time for a replacement projector lamp: Lamp is approaching the end of its useful life in full power opera­tion. Replacement Suggested!” When your Acer XD1250P projector lamp is coming to its end of life, the LAMP indicator will light solid red and the Acer XD1250P projector will automatically shut down. Replace the Acer EC.J2101.001 projector lamp immediately.

Find this lamp sold on Amazon by these authorized dealers:

Replacing the Acer EC.J2101.001 projector lamp

Before installation follow these important safety steps:

  • Turn off the Acer XD1250P projector and unplug the AC cord.
  • These projectors operate under high temperatures and there is a risk of burning if the projector has not cooled enough. Allow the XD1170D to cool for one hour. It should be cool to the touch.

Acer_XD1250P_projector_ACER-EC.J2101_remove_projector_lamp_coverAcer_XD1250P_projeAcer_XD1250P_projector_ACER-EC.J2101_remove_projector_lamp_cover-2

 

1. Use a screwdriver to remove the two screws from the cover.

2 Lift the cover off the projector and place it to one side.

Acer_XD1250P_projector_ACER-EC.J2101_remove_projector_lamp_screws

 

3. Use a screwdriver to remove the two screws holding the Acer XD1250P projector lamp in place. screw from the cover. Lift the wire handle on the Acer EC.J2101.001 bulb and gently pull the lamp up to remove it. Don’t throw the old Acer EC.J2101.001 projector lamp into regular garbage as it contains mercury — send it to a local recycling program.Acer_XD1250P_projector_ACER-EC.J2101_install_new_projector_lamp

4. Take the new Acer EC.J2101.001 projector lamp using the wire handle. Avoid touching the bare bulb; the oil on your finger can leave a black mark on the lamp affecting the projected image. Tighten the screws on the new Acer EC.J2101.001projector lamp.

Acer_XD1250P_projector_ACER-EC.J2101_reinstall_projector_lamp_coverPut the lid back onto the projector. Tighten the screw holding the lid in place. Plug the AC cables back into the projector. Turn the project on so you can reset the lamp timer.

Resetting the projector lamp timer

Acer_XD1250P_projector_ACER-EC.J2101

 

It’s important to always reset the lamp timer after replacing the projector lamp in your XD1250P projector. You want the projector to track how many hours the lamp has been used and send out warning messages when the Acer EC.J2101.001 reaches end of life.

To reset the Projector Lamp timer:

  • Open the MAIN MENU. Press ENTER.
  • Scroll down to the MANAGEMENT menu. Press ENTER.
  • Scroll down to the Lamp Hour reset option.
  • Press the right arrow.
  • The lamp will be reset to zero.
  • You can set the Eco Mode and Lamp Hours left plus time remaining.

Learn more tips for extending lamp life.

Acer_XD1250P_Replacement_Bulb_Acer_EC-J2101-001_ projector_lampA green alternative

The Acer XD1250P projector has the option of also just replacing the actual bulb and re-use the plastic cage. This reduces waste and is a great way to green your projector.

Watch our training video to learn more.

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Eiki-LC-X4L_projector_lamp_Eiki_610-292-4848_POA-LMP39Replace the Eiki LC-X4L projector lamp by following our step-by-step manual.

Buy the right projector lamp

Always install an authentic Eiki LC-X4L projector lamp in your Eiki LC-X4L to keep it working properly. Look for the seal of approval before buying Eiki POA-LMP39 and avoid generics for the following reasons:

Go with original OEM projector lamps and save yourself hassles.

Find this lamp sold on Amazon by these authorized dealers:

Watch for end of life warnings

The Eiki LC-X4L uses two Eiki POA-LMP39 projector lamps, so it’s recommended you change both at the same time. Watch for signs indicating it’s time to change the projector lamp. There are several key functions that will help you manage end of life for the projector lamp.

Lamp Status

Eiki_LC-X4L_Eiki_POA-LMP39_projector_lamp_mode

The Lamp Management Function detects the status of bots lamps and displays it on screen. The lamp status is also displayed for 5 seconds when the projector is turned on. The LAMP REPLACE indicator lights yellow when either lamp is nearing end of life.

Eiki LC-X4L_Eiki_POA-LMP39_projector_lamp_remove_coverOn screen status:

  • ON: Yellow lamp on screen: Lamps are functioning normally.
  • OFF: Dim Lamp: Lamp is turned off and not in use.
  • NEAR END: Red lamp: Projection Lamp is nearing its end. When image becomes darker or color becomes unnatural, replace lamp. (The Lamp replace light on the projector lights yellow at the same time.
  • OUT: X Mark on lamp: The lamp has reached its end of life and fails to turn on. It may also be defective. Replace lamp corresponding with number marked X.

Lamp Mode Changeover: Lamp Management Function automatically changes the combination of lighting lamp (Lamp Mode) by detecting the status of each projector lamp. When any of the two lamps goes out, Lamp Mode is changed over from 2 lamps to 1 lamp. Lamp Mode can be switched to 2 lamps or 1 lamp manually. Check the number of lamps being used on the Lamp Status.

Changing the Eiki POA-LMP39 projector lamp

Follow these important safety steps before replacing the Eiki POA-LMP39 projector lamp.

  • The Eiki LC-X4L projector operates under very high temperatures. Let it cool for one full hour before attempting to replace the lamp in order to avoid being burned.
  • Turn off the projector by pressing the power button. Wait for the light to stop flashing.
  • Turn off the power switch at the back on the projector
  • Unplug any power cords.

NOTE: To maintain quality of picture (better balance of color and brightness in entire screen), replacing both lamps at the same time.

Eiki_LC-X4L_Eiki_POA-LMP39_remove_projector_lamp

  • Loosen the three screws on Lamp Cover and remove Lamp Cover.

 

Eiki_LC-X4L_Eiki_POA-LMP39_replace_projector_lamp

  • Loosen the 2 screws. Using the wire handle and pull out the projector lamp. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.
  • Replace the Lamp Assembly. NOTE: The Eiki POA-LMP39 contains mercury and should be properly recycled. Don’t place it into regular garbage.
  • Make sure that Lamp Assembly is set properly. Tighten the 2 screws on the new lamp
  • Replace Lamp Cover and tighten 3 screws. Connect AC Power Cord to a projector and turn projector on.
  • Reset Lamp Replacement Counter.

Reset Eiki LC-X4L lamp counter

Your Eiki LC-X4LA projector has a built in lamp counter to determine when the projector lamp should be replaced. It needs to be reset every time you replace the Eiki POA-LMP39 projector lamps. When the Lamp Replace Counter is reset, the LAMP REPLACE indicator stops lighting.

Eiki_LC-X4L_Eiki_POA-LMP39_reset_projector_lamp_timer

  • Turn projector on, press MENU button and ON-SCREEN MENU will appear.
  • Press POINT LEFT/RIGHT button(s) to move the red frame pointer to SETTING Menu icon. Press POINT DOWN button to move a red frame pointer to “Lamp counter reset.”
  • Press SELECT button.
  • Move arrow to select either Lamp 1 or Lamp 2. Press SELECT button.

 

Eiki_LC-X4L_Eiki_POA-LMP39_reset_projector_lamp_timer_2

  • Message “Lamp replace counter Reset?” is displayed.
  • Move pointer to YES and then press SELECT button.
  • NOTE: Be sure to reset correct lamp number otherwise LAMP REPLACE indicator continues lighting.
  • Another confirmation dialog box appears and select YES to reset Lamp Replace Counter.
  • Do not reset Lamp Replace Counter except after Projection lamp is replaced.

Extend the life of the Eiki POA-LMP39 projector lamp

Get more hours from your Eiki POA-LMP39 lamp by following these maintenance tips:

  • Keep your air filters clean to avoid overheating the projector.
  • Turn off the Eiki LC-X4L projector and let it stand unused for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
  • Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
  • Learn more with Top tips for extending DLP projector lamp life.
  • Press the MENU button to exit.

Save money, go green

Video_Changing_Lamp_for_Eiki_LC-X4LA_projector_lampLooking for a green alternative? Try replacing only the bulb and re-using the same projector lamp cage for the Eiki LC-X4L projector. You save money and reduce waste.

Watch our how to video guide to learn more.

 

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

NEC_NP-M230X_projector_NP15LP_projector_lampChange the NEC NP-M230X projector lamp in three easy steps.

Step 1: Knowing when to replace the projector lamp

How will you know the the NEC NP-M230X projector lamp needs to be replaced and is reaching end of life? Watch for the following signs:

  • the LAMP indicator will begin to blink red
  • message on screen reads LAMP HAS REACHED THE END OF ITS USABLE LIFE. PLEASE REPLACE THE LAMP AND FILTER.
  • colour looks off
  • picture is faint or has deteriorated

NEC_NP-M230X_check_NECNP15LP_projector_lamp_usageTrack the life of the NEC NP15LP projector lamp with the usage time menu. The progress indicator shows the percentage of remaining bulb life:

  • Go to INFO menu
  • Scroll down to USAGE TIME to display the LAMP LIFE REMAINING and LAMP HOURS USED
  • When the lamp usage reaches 0, the Lamp Life REMAINING starts a count down from 100 hours
  • When the count down reaches 0, the projector will turn off and not turn on.

Step 2: Buy authentic

Avoid using a generic projector lamp in your NEC NP-M230X projector. Be sure to always install an authentic NEC NP15LP lamp. Generics have been created using toxic materials including Krypton-85 and they are prone to explosions with a shorter lamp life. Installing them often damages the sensitive electronics in your NEC NP-M230Xprojector.

NOTE: New air filters are shipped with the lamp and it’s recommended you replace them at the same time.

Find this lamp sold on Amazon by these authorized dealers:

Step 3: Changing the NEC NP15LP projector lamp

Follow these important safety instructions before installing the new NEC NP15LP projector lamp

  • turn off the NEC NP-M230X projector.
  • unplug the projector from its power source.
  • unplug the power cable.
  • wait until the projector is cool to the touch to avoid getting burned.

NEC_NP-M230XNEC_NP16LP_projector_lamp_remove_lamp_screwLoosen the NEC NP-M230X projector lamp cover screw.

 

 

 

 

NEC_NP-M230X_projector_lamp_NEC_NP16LP_remove_lamp_cover

Push and slide the NEC NP-M230X projector cover off.

 

 

 

 

NEC_NP-M230X_remove_NEC_NP16LP_projector_lamp_screws

 

Loosen the two screws holding the NEC NP15LP projector lamp in place. (The screws will not come out only loosen.)

 

 

NEC_NP-M230X_remove_NEC_NP16LP_projector_lamp

Remove the projector lamp by holding the indent and pulling up.

NOTE: Your NEC NP15LP lamp should be properly recycled. These lamps contain mercury and can’t be placed into common garbage.

 

 

NEC_NP-M230X_projector_lamp_install_new_NEC_NP16LPInstall a new lamp housing into the NEC NP-M230X projector, gently pressing the projector lamp housing into the socket. Take care not to touch the actual bulb as your finger prints can leave oil marks that burn black marks onto the bulb.

 

 

 

NEC_NP-M230X_projector_tighten_NEC_NP16LP_projector_lamp_screws

Push the top center on the projector lamp to secure it. Tighten the screw on the projector lamp.

 

 

 

NEC_NP-M230X_projector_replace_lamp_cover_NEC_NP16LP_projector_lamp

Reattach the NEC NP-M230X lamp cover by sliding the cover until it snaps into place. Tighten the screw on the lamp cover.

 

 

Replacing the filters

There are four filters in the NEC NP-M230X projector:

  • Honeycomb hard filter – large and small
  • Accordion soft filter — large and small

Replace all four filters at the same time. Before replacing the filters wipe off any dust and dirt that came loose from the old filters. NOTE: The filters are made with two different types of material in the membrane. Both perform the same.

 

NEC_NP-M230X_projector_lamp_NEC_NP16LP_remove_air_filterPush the catch to release the NEC NP-M230X filter and gently pull it out.

 

NEC_NP-M230X_projector_lamp_NEC_NP16LP_detach_filter_cover

The filter cover is fixed at six separate points in the projector. Bow the filter cover by pushing it slightly until it releases.

 

 

 

NEC_NP-M230X_projector_lamp_NEC_NP16LP_replace_dark_filtersRemove the dark sponge filter and clean the filter unit and cover. Attach the new non-woven white material filters.

 

 

NEC_NP-M230X_projector_lamp_NEC_NP16LP_replace_four_filters

  • Filter unit: Attach two honeycomb hard filters to the NEC NP-M230X filter unit.
  • Filter cover: Attach the two accordion soft filters to the filter cover. Be sure to align the accordion slits with the protrusions of the filter cover.

 

NEC_NP-M230X_projector_lamp_NEC_NP16LP_attach_filter_cover

Attach the filter cover back to the filter unit. Align the filter until with the filter cover and push the protrusions into place. Make sure all the six mounting points are aligned properly.

 

 

 

NEC_NP-M230X_projector_lamp_NEC_NP16LP_attach_filter

Insert the two catches of the top of the filter into the groove of the cabinet. Push the filter until it clicks into place.

 

Reset the lamp timer

Once the NEC NP15LP projector lamp and NEC NP-M230X projector filter have both been replaced you will need to reset the timer for both. You want the projector to be able to accurately track the projector lamp life.

NEC_NP-M230X_projector_lamp_NEC_NP16LP_lamp_timer

Clear usage hours and reset hours

  • Plug in the power cored into the wall outlet.
  • Turn on the projector.
  • From the MENU select RESET.
  • Choose CLEAR LAMP HOURS.
  • A confirmation message appears.
  • Select YES.

Reset the filter hours:

  • Scroll up to CLEAR Filter HOURS.
  • A second submenu will appear.
  • Select YES. Press the ENTER button.

Extending the life of the NEC NP15LP projector lamp

Get your newly installed NEC NP15LP lamp will last longer by choosing the ECO option. The ECO MODE increases projector lamp life by lowering the power consumption. There are three modes to choose from:

  • Auto Mode: 4000 hours
  • Normal: 5000 hours
  • Eco ModeL 8000 hours

Learn more tips to extend the life of the NEC NP15LP lamp.

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Hitachi_CP-X600_projector_Hitachi DT00771_projector_lampReplacing the Hitachi CP-X600 projector lamp is simple and fast — just follow our guide!

 When does projector lamp needs to be replaced?

Watch for these signs that indicated the Hitachi CP-X600 projector lamp is reaching its end of life:

  • Hitachi CP-X600 Lamp Indicator light will start flashing red.
  • Color tone on the screen may also appear weak or washed out.
  • Picture has poor colour quality.
  • You may notice the Hitachi DT00771 CPX605 starts to go dark after being used for long period of time. It does have a finite life and trying to force it to work beyond its normal life can damage your Hitachi CP-X600 projector.

Invest in an authentic projector lamp

Be sure to install an authentic projector lamp to keep your Hitachi CP-X600 projector working at its best. You’ll need a Hitachi DT00771 CPX605 projector lamp.

Avoid generics. With their inferior parts, combined with a shorter life means counterfeit projector lamps cost you more in the end. Avoid exposure to the toxic materials and parts used to create the lamps and keep your warranty in place. Look for the seal of approval to make sure you are getting an authentic projector lamp.

Find this lamp on Amazon sold by these authorized dealers:

Replace the projector lamp

Hitachi-CP-X600_Hitachi_DT00771_projector_lamp_cover_screwTurn the Hitachi CP-X600 projector off, and unplug the power cord. Allow the projector to cool for at least 45 minutes. It should be cool to the touch. This projector works using high heat and there is danger you can be burned.

NOTE: If the projector is mounted on the ceiling, don’t stand underneath the projector while opening the cover.

 

 

 

Hitachi-CP-X600_Hitachi_DT00771_projector_lamp_remove_coverLoosen the screw on the lamp cover (marked with an X). Slide the cover to off the projector and set it one side.

Hitachi-CP-X600_Hitachi_DT00771_projector_lamp_handlesLoosen the three screws holding the Hitachi DT00771 CPX605 projector lamp in place. Slowly pick up the projector lamp by its handle and pull out taking care not to bang the bulb on the side of the projector. If you do shatter the bulb, you will need take time to properly clean the projector. Learn how to clean up a broken lamp.

NOTE: The Hitachi DT00771 projector lamp contains mercury and should be properly recycled. Don’t place it into regular garbage.

Finish the installation:

  • Insert the new Hitachi DT00771 CPX605 projector lamp making sure to line it up properly and tighten the three lamp screws.
  • Slide the cover back onto the projector, lock it in place and fasten the screw.
  • Turn on the projector and set the lamp time:

To reset the projector lamp timer:

Hitachi CP-X600_reset_projector_lamp_timerNote: Reset the projector lamp time only when you have replaced the lamp so the Hitachi CP-X600 projector can properly track the lamp life. Otherwise you run the risk of using the lamp beyond its lamp life.

Press the MENU button

  • Scroll down to the GO TO ADVANCED MENU option. Press ENTER
  • Scroll down to the OPTION menu in the left column and press ENTER.
  • Scroll down to LAMP TIME. Press ENTER To make a dialogue field appear
  • Scroll up to the RESET option on the dialogue box.
  • The lamp setting will be set to zero.

Get more hours from your Hitachi DT00771 CPX605 by keeping your air filters clean to avoid overheating the projector. Learn more with Top tips for extending DLP projector lamp life.

Go green, save money

Hitachi_Replace_BulbIf you are looking for a green alternative, why not consider changing only the bulb and leaving the housing for the bulb. Our training video shows you how simple it is.

 

 

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Optoma_DX623_Optoma_BL-FU185A_SP.8EH01GC01_projector_lampThis four-step guide will show you how to install a new replacement Optoma DX623 multimedia projector lamp.

Invest in authentic replacement projector lamps

Be sure to have your back-up replacement Optoma DX623 multimedia projector lamp ready so you can replace the lamp immediately when needed. Keep your Optoma DX623 multimedia projector working at optimum levels by investing in an authentic projector lamp. When buying on the Internet, make sure you are buying an OEM and look for the seal of approval. Generic lamps have a shorter lamp life than original lamps and are created with toxic materials. When you buy copy-cat lamps you get no guarantee or refunds and they can damage the sensitive electronics in your projectors. Learn How to spot a counterfeit.

Find this lamp sold on Amazon by these authorized dealers:

End of life warnings

Optoma_DX623_Optoma_BL-FU185A_SP.8EH01GC01_replacement_warning_projector_lampWhen the Optoma BL-FU185A projector lamp is reaching end of life, you will notice the Lamp-LED light flashing red. A lamp warning message also appears on screen.

If you hear a loud pop when turning on the projector, the Optoma BL-FU185A (SP.8EH01GC01) projector lamp has broken. Learn what to do if the projector lamp has exploded inside the projector.

4-steps to installing the Optoma BL-FU185A projector lamp

Follow these important safety tips before replacing the Optoma BL-FU185A  projector lamp:

  • Switch off the power to the Optoma DX623 multimedia projector by pressing the Power/Standby button.
  • Disconnect the power cord.
  • Allow the Optoma DX623 multimedia projector to cool down for at least 30 minutes. If should be cool to the touch. These projectors run using high temperatures and you can burn yourself badly if you don’t allow the projector to cool down.

Optoma_DX623_Optoma_BL-FU185A_SP_projector_lamp_warningSteps to remove the lamp

1. Use a screwdriver to undo the two screws holding the projector lamp cover in place. The screws on the lamp cover and the lamp cannot be removed.

2. Remove the lid and place to one side. Don’t lose the lid as the Optoma DS623 projector will not turn back on until the lamp cover has been properly installed.

3. Remove the two screws holding the Optoma BL-FU185A projector lamp in place.

Note: The used Optoma BL-FU185A  projector lamp contains mercury and should be properly recycled. Don’t throw it into regular garbage.

4. Lift up the wire handle on the Optoma BL-FU185A  projector lamp and slowly remove it from the projector. Be careful not to bang the lamp against the projector as this may case the bulb to break. Learn how to clean up a broken lamp.

Steps to install the new projector lamp:

1. Remove the new Optoma BL-FU185A  projector lamp from its packaging. Taking care not to touch the actual bulb, lift up the handle on the new lamp and insert it gently into the Optoma DS623 projector.

2. Tighten the two screws on the projector lamp.

3. Replace the lamp cover and tighten its two screws.

Reset the Projector Lamp Replacement Timer

Optoma_DX623_Optoma_BL-FU185A_SP_reset_timerThe Optoma DX623 multimedia projector has an automatic projector lamp timer that tracks the numbers of hours left in the lamp. If you don’t reset the lamp replacement timer you run the risk of the lamp being used beyond its recommended life and possibly exploding in the projector.

To reset the Projector Lamp Replacement Timer:

  • Turn on the projector.
  • Using the remote press MENU
  • Select OPTIONS
  • Select LAMP SETTINGS
  • Select LAMP RESET
  • Select YES.
  • Press MENU to exit.

Tips for extending Optoma BL-FU185A  projector lamp life:

  • Chose the “STD” mode to to dim the projector lamp and lower power consumption. This will extend the lamp life by up to 130%.
  • Keep your air filters clean to avoid overheating the projector.
  • Every 24 hours, turn off the projector and let it stand for 1 hour
  • Make sure there is enough airflow around the Optoma DX623 multimedia projector particularly if it’s been permanently mounted.
  • Learn more with Top tips for extending DLP projector lamp life.

Green your Optoma DX623 projector

Optoma-BL-FU185A_replacement_bulb_training_videoThe Optoma DX623 projector has the option of re-using the existing lamp cage and replacing only the actual bulb. A great way to reduce and recycle. Watch our Optoma BL-FU185A training video to learn more.

Tagged with: , , ,

by avatarShelagh McNallyPosted on Posted in Articles, FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Extreme summer heat and humidity can be deadly for your projector.

Keep your projector safe from summer heat and humidity with these tips.

  • Travel with your projector on a well-padded case that fits properly.
  • Never leave your projector inside the car for hours. Summer heat can turn your car into a dangerous oven that warps the internal components.
  • Inside or outside, store your projector away from direct sunlight and summer heat.
  • Avoid using the your projector in a room with more than 80% humidity. The excess moisture in the air can damage the projector’s electronic.
  • Projectors are designed to disperse heat via their exhaust ventilation. Taking the projector out of its carrying case will cool it down after it’s been exposed from summer heat.
  • When temperatures climb and summer storms happen, you may experience power outages. Using surge protectors, power invertors or spare batteries can stop your projector from electrical shortages.
  • Projectors are happiest working on a temperature range of 50 to 95 degrees Fahrenheit (10 to 35 degrees Celsius). Don’t operate in extreme heat.
  • Going from extreme summer heat to colder air conditioned rooms can damage the optics in your projector. When coming into an air-conditioned room from the hot outdoors, let your projector cool down before turning it on.
  • Keep your air filters clean so when the projector is working it can stay cool and dissipate the heat. If you are working the projector in a dusty environment, clean the filter regularly.
  • Make sure there is enough room around the projector’s air vents so airflow is not restricted. Make sure there is no clutter around the projector. Restricted airflow may cause the projector to shut down due to overheating.
  • Use the eco mode or dimmer lighting on the projector to keep the temperature down.
  • After use, let the projector sit and cool off before moving it and taking it back outside into summer heat.

Read more maintenance tips for your projectors:

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in uncategorized — No Comments ↓

Proudly-Made-in-the-USA_projector_lamps

Only a few companies sell authentic projector lamps made in the North America. Make sure you’re buying from a recognized authorized dealer.

The Internet has been flooded with companies selling “generic” projector lamps claiming to be authentic. The truth is these projectors are shipped from overseas and have been created by copycat manufacturers. These projector lamps may have a cheaper price tag but actually end up damaging your projector.

Projector lamp technology

DLP Projectors use high pressure to generate light and this pressure needs to be controlled inside the  projector lamp. An authentic OEM (Original Equipment Manufacturer) projector lamp has been calibrated to the exact wattage so they are able to handle the pressure. Generic lamps have not designed to handle the subtleties in wattage and pressure. They give off either too much wattage so are prone to overheating and explosions. When generic lamps give off too little pressure the result is low light and poor picture quality.

 Beware_generic_lamps_authentic_projector _lampNot all projeector lamps are equal

The official  projector lamp brand is manufactured by Philips Lighting. It handles over 60% of the projector lamp market. They’ve spent millions of dollars creating a product that works with the sophisticated mechanism in various projector brands. Philips creates every projector lamp with he correct materials unlike copycat manufacturers who use toxic substitutes. Philips OEM projector lamps are also created with the highest safety standards unlike generic lamps thrown together in order to sell quickly.

Seal_of_approval_from_Philip_authentic_projector _lamps

Look for the seal of approval

When you purchase from an authorized manufacturer and dealer, you know you’re receiving a Philips projector lamp that is reliable, durable and safe. Philips gives select companies its Global Premium Partner status. This seal of approval guarantees that the company is selling high quality lamps guaranteed to deliver the best performance while protecting your health and your projector.

Generic brands sold through the Internet can’t offer this kind of guarantee, particularly those manufactured in China, where the standards are lower and regulations not as strict. Installing a cheaper brand may actually damage other sensitive components connected to your projectors operating system. You may also find your warranty has become void after installing these third-party parts.

The few dollars you save with generic “compatible” lamps is not worth it in the long run. Save yourself unnecessary headaches — buy a You’ll be getting a far superior product with a replacement guarantee and tech support.

6 good reasons to avoid generics

Protect yourself and ask for the Philips seal of approval before buying any projector lamps off the Internet.

Learn the 7 Ways to spot a counterfeit lamp.

 

Tagged with: , , ,
Join the discussion on Facebook! All your questions, answered! The Screen & Projector Group