About Us - Page 59 of 176 - DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP

Easy instructions for your Epson EMP-8300 projector lamp

Shelagh McNallyPosted on April 16, 2014 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

This 3-step instruction guide will show you how to replace the Epson EMP- 8300 projector ;a,[.

Step 1: Buy authentic projector lamps!

Your Epson EMP-8300 uses the Epson ELPLP23 projector lamp. It’s important to purchase the right Epson EMP-8300 projector lamp. Look for the seal of approval and avoid purchasing copycat, generic lamps for your Epson EMP- 8300 projector

6 Reasons for avoiding generic lamps:

no safety guards to protect your eyesight.
shorter life so end up costing more.
prone to explosions.
created with toxic substitutes
not operly calibrated
damage the sensitive and expensive electronics optics

Learn how to spot the copycat fake lamps: 7 Ways to Spot a Counterfeit Lamp.

Find this lamp on Amazon sold by these authorized dealers:

Step 2: When to replace

When the projector lamp is reaching end of life, the “REPLACE LAMP” message appears on screen. The lamp indicator on the Epson EMP-8300 projector will also start flashing orange. You may notice the image has gotten darker on screen. Replace the projectorlamp immediately when you see any of these signs.

Expected life span

Life span for your projector lamp will vary depending on how often the air filters are cleaned but also on the brightness setting:

With continuous use at high brightness: Approx. 1900 hours
With continuous use at low brightness: Approx. 2900 hours

Consult the About menu to see how many hours are left until the Epson ELPLP23 (V13H010L233) projector lamp reaches end of life.

Step 3: Install the Epson EMP-8300 projector lamp

Do these safety steps BEFORE installing the new Epson ELPLP23 (V13H010L233) projector lamp:

Turn off the projector by pressing the power button.
Wait 30 second for the cool-down period before disconnecting the power cable.
Continue to let the Epson EMP-8300 cool down for one hour before replacing the lamp. This projector operates under high temperatures and there is danger of being burned if the projector has not cooled down.

To replace the V13H010L233 projector lamp:

Remove the lamp cover on the Epson EMP-8300 projector by loosening the two keeping it in place. (The cover is at the back of the projector.) Take extra precaution if the projector is mounted on the ceiling. If you have installed the rear cover after mounting on the ceiling, you should remove that cover first.

Loosen the three screws holding the projector lamp in place (screws don’t come out the whole way).

Fold out the wire handle and pull the Epson ELPLP23 – V13H010L233 projector lamp straight out while supporting it with one hand. If replacing the lamp yourself, be careful to avoid pieces of broken glass. Pulling too quickly can cause the bulb to shatter. Learn how to clean up a broken lamp.

NOTE: The Epson ELPLP23 contains mercury and should be properly recycled. Don’t place it into regular garbage.

Gently insert the new Epson ELPLP23 – V13H010L233 projector lamp using the wire handle while supporting it with the other. Be careful not to touch the actual glass bulb as your fingerprint will burn into a black spot when the lamp heats up. This will cause black spots on the screen.

Once the projector lamp is fully inserted, tighten three screws that will hold the lamp in place.

Replace the Epson EMP-8300 projector cover and tighten the screws holding the cover in place.

You must now reset the lamp operating timer.

Resetting the Lamp Operating Timer

The Epson EMP-8300 has a lamp timer than can accurately track the lamp life and send the Lamp replacement message when it’s time for the Epson ELPLP23 – V13H010L233 projector lamp to be replaced. Each time you replace the lamp you must reset the lamp timer. Failure to reset the lamp operating timer and you will not know when end of life is being reached. NOTE: Resetting the timer before installing a new Epson ELPLP23 – V13H010L233 projector lamp can cause serious damage to your projector.

Press the MENU button on the remote control projector’s control panel to open the main menu.
Use the pointer buttons on the remote control to scroll down the menu on the left and highlight the ABOUT option.
Scroll down to RESET LAMP TIMER.

Press ENTER to bring up the Execute prompt.
Select YES.
Press ENTER.
Press ESC or MENU.

Get more hours from your Epson ELPLP23 projector lamp by following these maintenance tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson EMP-8300 projector and let it stand unused for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life.

Tagged with: epson authentic lamps, Epson ELPLP23 lamp, Epson EMP-8300 projector

Install a new Studio Experience Matinee 1HD projector lamp

Shelagh McNallyPosted on April 15, 2014 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Use our step-by-step guide to change Studio Experience Matinee 1HD projector lamp.

The Studio Experience Matintee 1HD projector lamp is a division of Boxlight but uses the Sanyo POA-LMP54 (service parts no 610 302 5933) lamp.

When the Studio Experience Matinee 1HD projector lamp is reaching end of life, the Lamp Indicator will begin to start blinking yellow. The Lamp Indicator is found on the top control panel.

Authentic lamps are crucial

Invest in an authentic Sanyo POA-LMP54 (610 302 5933) lamp to keep your Studio Experience Matinee 1HD working at its best. Look for the seal of approval before buying and avoid generics.

6 Reasons for avoiding generic lamps:

generics offer no safety guards to protect your eyesight
generics have a much shorter life so end up costing more
copycat lamps are prone to explosions
fake lamps are created with toxic substitutes
non generic lamps can’t be not properly calibrated
damage the sensitive and expensive electronics optics

Looking for a less expensive option? Want more information? Watch our step-by-step video on replacing only the Sanyo POA-LMP54 (service parts no 610 302 5933) bulb instead of the entire lamp housing.

Replacing the POA-LMP54 lamp

Before replacing the Sanyo POA-LMP54 (610 302 5933) lamp follow these important safety steps:

Turn off the projector
Unplug the AC cord.
Allow the Matinee 1HD projector to cool for 45 to 60 minutes. It should be cool to the touch before opening the projector. The Matinee 1HD operates using high temperatures and not waiting for it cool can result in a bad burn.

1. The lStudio Experience Matinee 1HD lamp cover is located at the bottom of the projector. Gently turning it over and place it on a soft surface. Loosen the screw holding the cover in place and remove the cover.

2. Loosen the two screws holding the Sanyo POA-LMP54 lamp in place. Grab the handle on the lamp cage and gently remove the lamp. Place to one side. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter. NOTE: Your old Sanyo POA-LMP54 (service parts no 610 302 5933) lamp should be properly recycled. These lamps contain mercury and can’t be placed into common garbage.

3. Carefully place the new Sanyo POA-LMP54 (6103025933) lamp in the projector using the wire handle. Avoid touching the glass or the bulb since the oil from your fingers may cause black spots on the bulb when the projector heats up. The lamp should slide in easily – don’t force it. Pulling too quickly can cause the bulb to shatter. Learn how to clean up a broken lamp.

5. Tighten the two screws on the Lamp Assembly for the Sanyo POA-LMP54.

6. Replace and tighten the two screws on either side of Lamp Cover. Let the projector stand for five minutes so the lamp can stabilize. Re-connect the power cord and turn on the Studio Experience Matinee 1HD projector. You’ll need to reset the Lamp Counter.

Reset the lamp counter

Reset the Lamp counter only when Sanyo POA-LMP54 lamp has been replaced. Do not operate the projectors while any of the lamps are removed as this may result in the lamp exploding from being used beyond it’s life expectancy.

Turn the Studio Experience Matinee 1HD projector on.
Press the Menu option to display the On-Screen Menu.
Scroll down to the Setting option.
Select Lamp Control.
A second screen will appear.
Press Point left/right button(s) to move to move the red frame pointer to Lamp counter reset.
Press the Select button.
Another confirmation dialog box appears, select YES.
The Lamp box will disappear and the Lamp Replace Dialog box appears.
Select YES to reset Lamp Replace Counter.

Make your new Sanyo POA-LMP54 lamp last longer:

Wait at least five minutes before turning the Studio Experience Matinee 1HD projector off.
Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
Clean the air filter regularly.
Buy authentic.

Tagged with: authentic lamps, Sanyo POA-LMP54, Studio Experience Matinee 1HD

Replacement guide for the Canon LV-7545 projector lamp

Shelagh McNallyPosted on April 15, 2014 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Our guide shows how to change the Canon LV-7545 projector lamp

Avoid generics

Be sure to buy authentic Canon LV-7545 projector lamp. The Internet has been swamped with companies selling generic, compatible lamps that are just not as good as original OEM lamps.

Created with carcinogenic, toxic substances as well as inferior parts, shoddy workmanship make these generic lamps vulnerable to explosions. Counterfeit generica lamps also compromise your health and safety and installing one voids your warranty. Spend the few extra dollars for a genuine OEM lamp and keep your Canon LV-7545 projector working properly. Learn how to spot a counterfeit

End of life signs

When the Canon LV-LP13 projector lamp has reached its end of life – between 2000 to 3000 hours depending on maintenance and settings – the LAMP REPLACE on the projector will light up orange. Replace the lamp immediately when you see this.

Other warning signs may be a dim picture, colour that appears washed and a image that is fading.

Before changing the projector lamp:

Let the Canon LV-7575 cool down for at least 45 minutes. This projector operates at an extremely high temperature and you could get badly burned if it’s still hot. Don’t rush it.
Be sure to unplug the electrical cord so there is no chance the projector could get turned on during the installation. This could damage your projector.

Turn off the Canon LV-7545 projector and unplug the AC power cord.
Allow the projector to cool for at least 45 minutes.
Loosen the two screws and open the lamp cover.
Loosen the two screws on the Canon LV-LP13 projector lamp assembly by using the built in handle.
NOTE: The used LV-LP13 projector lamp contains mercury and should be properly recycled. Don’t throw it into regular garbage.
Pulling too quickly can cause the bulb to shatter. Learn how to clean up a broken lamp.

Replace the projector lamp assembly with a new Canon LV-LP13. Be careful not to touch the actual bulb as oil from your fingers can leave black marks on the lamp.
Tighten the two screws on the lamp.
Put back the projector lamp cover and tighten its two screws.
Connect the AC power cord to the Canon LV-7545 projector and turn on the projector to reset the lamp timer.

Reset the lamp timer

After replacing the Canon LV-LP13 projector lamp, you’ll need to turn off the LAMP REPLACE indicator by resetting the LAMP REPLACE COUNTER. The counter tracks the number of hours the lamp has been used and triggers the warning light when the lamp is reaching its end of life. Not resetting it after may stop your projector from turning back on.

Turn the projector on and press the MENU.
The On-Screen menu will be displayed on the left.
Using the arrow buttons, mover the red frame pointer to the SETTING menu icon.
Press the up/docwn buttons, move to the LAMP COUNTER option.

Press OK to open up as the RESET LAMP COUNTER box.
Click on the RESET option to open a confirmation window.

Click on YES.
Press OK.
The lamp hours will be reset to zero.

Longer life for the Canon LV-7545 projector lamp

Extend the life of the lamp by more than 1,000 hours by changing the brightness of the screen.

Auto mode: Brightness according to the input signal.
Normal mode: Normal brightness and standard setting
Silent mode: Lowers brightness to reduce the power consumed by the lamp and extending lamp life.

Learn more with Top tips for extending DLP projector lamp life.

Save money and go green

Looking for a green alternative? Try replacing only the bulb and re-using the same plastic cage. Watch this Canon LV-LP28 Projector Lamp Replacement Video Guide to find out more.

Tagged with: authentic lamps, Canon LV-7545 projector, Canon LV-LP13 (7670A001) lamp

3 steps to replace the Hitachi CP-X268A projector lamp

Shelagh McNallyPosted on April 14, 2014 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Changing the Hitachi CP-X268A projector lamp is simple and fast.

Step 1: Be prepared with the right lamp

With the right Hitachi CP-X268A projector lamp and by following our step-by-step guide, you will be able to install a new lamp in under 15 minutes. Keep your Hitachi CP-X268A projector working at its best by always using authentic OEM Lamps. Look for the seal of approval before purchasing a

so you can be sure to be getting the real deal. It can be confusing to shop on line and get the right lamp. Your key to knowing if the Hitachi CP-X268A projector lamp is authentic or not: If the price seems to be too good to be true, it’s a copycat lamp. These counterfiet lamp just don’t deliver and have many problems, which make them more expensive in the end.

Why avoid generics:

With their inferior parts, counterfeit lamps are prone to exploding
generics have a shorter life
these lamps are created using toxic chemicals as substitutes
can’t be calibrated properly so deliver a much poorer image
make your warranty void.

Keep your projector working and go with an authentic Hitachi DT00751 CPX260 lamp.

Step 2: Watch for end of life with the Hitachi CP-X268A projector lamp

Your Hitachi CP-X268A projector uses the Hitachi DT00751 CPX260 lamp and when it reaches end of life, there will be several tell tale signs:

Hitachi CP-X268A Lamp Indicator light will start flashing red.
Color tone on the screen may also appear weak or washed out.
Picture has poor colour quality.
You may notice the Hitachi DT00751 starts to go dark after being used for long period of time.

The Hitachi DT00751 CPX260 lamp has a finite life and trying to force it beyond its normal lamp life can damage your Hitachi CP-X268A.

Find this lamp on Amazon sold by these authorized dealers:

DT00751 Hitachi CP-X260 Projector Lamp
<br>

Step 3: Installing the Hitachi DT00751 CPX268 lamp

Before installing a new lamp be sure to turn off the Hitachi CP-X268A and let the projector cool down for at least one hour. This projector operates using high temperatures and there is a risk of you burning yourself if the projector has not cooled.

Turn off the projector by pressing the power button.
Unplug any power cords.
Loosen the Hitachi CP-X268A lamp cover screw
Slide the lamp cover to the side to remove it.

Loosen the screws on the lamp. Gently lift up the wire handle and pull out the Hitachi DT00751 CPX260 lamp.
NOTE: The Hitachi DT00751 contains mercury and should be properly recycled. Don’t place it into regular garbage.
Take the new DT00751 lamp out of its packaging.
Pick up the Hitachi DT00751 lamp by the handle and gently insert the lamp into the projector making sure not to bang the lamp. Pulling too quickly can cause the bulb to shatter. Learn how to clean up a broken lamp.
Avoid touching the actual bulb as oil from your fingers can leave marks on the bulb that will burn into black spots.
Slide the Hitachi CP-X265A lamp cover back in place and firmly fasten the lamp cover a screw.
Turn the projector on and reset the lamp time.

Resetting the Hitachi CP-X268A lamp timer

Reset the lamp time only when you have replaced the lamp so the Hitachi CP-X268A projector can properly track the lamp life. Otherwise you run the risk of using the lamp beyond its lamp life.

Press the MENU button
When the EASY MENU has appeared press Enter to choose
Scroll down to the ADVANCED MENU option.
Scroll down to OPTION menu.
Press ENTER.
Scroll down to LAMP TIME.
A dialog field will appear.
Choose RESET on the dialog field.
Press ENTER.
The lamp time will be reset to 0.
Press the MENU button to exit.

Get more hours from your Hitachi DT00751 CPX260 lamp by keeping your air filters clean to avoid overheating the projector. Learn more with Top tips for extending DLP projector lamp life.

Tagged with: authentic lamps, Hitachi CP-X268A projector, Hitachi CP-X268A projector lamp, Hitachi DT00751 CPX260 lamp

Install a NEC M260WS projector lamp

Shelagh McNallyPosted on April 11, 2014 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Follow this step-by-step guide to install new lamp in your NEC M260WS projector lamp.

Buy authentic!

The first thing to do is buy an OEM replacement NEC M260WS projector lamp. Your NEC M260WS projector uses the NEC NP15LP projector lamp. Avoid the cheaper generic lamps with their shorter lamp life and toxic materials. They are prone to explosions and often damage the sensitive electronics in your NEC M260w projector.

NOTE: New air filters are shipped with the lamp and it’s recommended you replace them at the same time.

Find this lamp sold on Amazon by these authorized dealers:

Lutema for NEC NP15LP Replacement DLP/LCD Cinema Projector Lamp – Philips Inside
NP15LP NEC NP15LP Projector Lamp
NP15LP – Lamp With Housing For Nec NP-M300X, NP-M260X, M300X, M260X, M260W, NP-M260W, NP-M230X, M260XSG, M260XS, M260WS, M230X Projectors
NP15LP – Lamp With Housing For Nec NP-M300X, NP-M260X, M300X, M260X, M260W, NP-M260W, NP-M230X, M260XSG, M260XS, M260WS, M230X Projectors

When to replace the NEC M260WS projector lamp

How will you know the the NEC M260WS projector lamp needs to be replaced and is reaching end of life? Watch for the following signs:

the LAMP indicator will begin to blink red
message on screen reads LAMP HAS REACHED THE END OF ITS USABLE LIFE. PLEASE REPLACE THE LAMP AND FILTER.
colour looks off
picture is faint or has deteriorated

Checking projector lamp end of life

Track the life of the NEC NP15LP projector lamp with the usage time menu. The progress indicator shows the percentage of remaining bulb life:

Go to INFO menu
Scroll down to USAGE TIME to display the LAMP LIFE REMAINING and LAMP HOURS USED
When the lamp usage reaches 0, the Lamp Life REMAINING starts a count down from 100 hours
When the count down reaches 0, the projector will turn off and not turn on.

Changing the NEC NP15LP projector lamp

Follow these important safety instructions before installing the new NEC NP15LP projector lamp

turn off the NEC M260WS projector.
unplug the projector from its power source.
unplug the power cable.
wait until the projector is cool to the touch to avoid getting burned.

Loosen the NEC M260W projector lamp cover screw.

Push and slide the lamp NEC M260WS projector cover off.

Loosen the two screws holding the NEC NP15LP projector lamp in place. (The screws will not come out only loosen.) Remove the lamp by holding the indent and pulling up. Pulling too quickly can cause the bulb to shatter. Learn how to clean up a broken lamp.

NOTE: Your NEC NP15LPprojector lamp should be properly recycled. These lamps contain mercury and can’t be placed into common garbage.

Install a new lamp housing into the NEC M260WS projector, gently pressing the lamp housing into the socket. Take care not to touch the actual bulb as your finger prints can leave oil marks that burn black marks onto the bulb.

Push the top center on the lamp to secure it. Tighten the screw on the lamp.

Reattach the NEC M260WS projector lamp cover by sliding the cover until it snaps into place. Tighten the screw on the lamp cover.

Replacing the filters

There are four filters in the NEC M260WS projector:

Honeycomb hard filter – large and small
Accordion soft filter — large and small

Replace all four filters at the same time. Before replacing the filters wipe off any dust and dirt that came loose from the old filters. NOTE: The filters are made with two different types of material in the membrane. Both perform the same.

Push the catch to release the NEC M260WS filter and gently pull it out.

The filter cover is fixed at six separate points in the projector. Bow the filter cover by pushing it slightly until it releases.

Remove the dark sponge filter and clean the filter unit and cover. Attach the new non-woven white material filters.

Filter unit: Attach two honeycomb hard filters to the NEC M260WS filter unit.
Filter cover: Attach the two accordion soft filters to the filter cover. Be sure to align the accordion slits with the protrusions of the filter cover.

Attach the filter cover back to the filter unit. Align the filter until with the filter cover and push the protrusions into place. Make sure all the six mounting points are aligned properly.

Insert the two catches of the top of the filter into the groove of the cabinet. Push the filter until it clicks into place.

Reset the projector lamp timer

Once the NEC NP15LP projector lamp and NEC M260WS projector filter have both been replaced you will need to reset the timer for both. You want the projector to be able to accurately track the lamp life.

Clear usage hours and reset hours

Plug in the power cored into the wall outlet.
Turn on the projector.
From the MENU select RESET.
Choose CLEAR LAMP HOURS.
A confirmation message appears.
Select YES.

Reset the filter hours:

Scroll up to CLEAR Filter HOURS.
A second submenu will appear.
Select YES. Press the ENTER button.

Extending the life of the NEC NP15LP lamp

Get your newly installed NEC NP15LP projector lamp will last longer by choosing the ECO option. The ECO MODE increases lamp life by lowering the power consumption. There are three modes to choose from:

Auto Mode: 4000 hours
Normal: 5000 hours
Eco ModeL 8000 hours

Learn more tips to extend the life of the NEC NP15LP projector lamp.

Tagged with: authentic lamps, NEC lamps, NEC M260WS projector, NEC NP15LP lamp

3 steps to a new Vivitek H1081 projector lamp

Shelagh McNallyPosted on April 10, 2014 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

No need to call the technician! Our guide shows you how to replace Vivitek H1081 projector lamp in three easy steps.

Step 1: Watch your hours

Check the Vivitek H1081 projector lamp life if you notice the picture becoming distorted or the Power LED flashing 5 times consecutively.

To check the lamp hours:

Press the Menu button to open the OSD menu.
Press left/right arrow keys to move button to move to the STATUS Menu.
The LAMP HOUR field displays the number of hours the lamp has been in use.
You can expect 2000 hours lamp life. 3000 hours if Eco Mode has been turned on.

Step 2: Buy the right projector lamp!

Your Vivitek H1081 projector uses the Vivitek 5811116206-S projector lamp. Be sure the purchase an authentic projector lamp and avoid the temptation of a the generic lamps with their bargain prices. There are several problems associated with generics that you want to avoid and these include

shorter lamp life
prone to explosions.
manufactured with toxic and dangerous substitutes
can’t be properly calibrated.
voids your projector warranty if you install a generic.

Save yourself hassle and go an authentic Vivitek 5811116206-S projector lamp.

Step 3: Replace the 5811116206-S projector lamp

Before changing the Vivitek 5811116206-S projector lamp:

Reduce the risk of electrical shock by disconnecting the power cord on the Vivitek H1080 projector.
Reduce the risk of severe burns by allowing the projector to cool for at least 45 minutes.

Turn the projector around to locate the lamp cover screw. Remove the captive screw holding the lamp cover place.

Gently slide off the lamp cover and place it to one side. You will need to re-install the cover before turning on the Vivitek H1081 projector again.

Remove the 3 screws holding the Vivitek 5811116206-S lamp in place.

Using the wire handle, gently pull out the Vivitek 5811116206-S projector lamp. Pulling too quickly can cause the bulb to shatter. Learn how to clean up a broken lamp.

NOTE: The 5811116206-S projector lamp contains mercury and should not be thrown into regular garbage. Recycle your used projector lamps!

Lift up the wire handle on the new Vivitek 5811116206-S projector lamp and gently guide it into the H1081 projector.
Take care not to touch the actual bulb as the oil from your fingers will smudges that will burn into a black spots when the projector heats up.
Tighten the lamp screw.
Re-install the H1081 lamp cover and tighten the screw.
Reset the total lamp hour timer.

Resetting the Lamp Hour Timer

It’s important to only reset the lamp timer when the Vivitek 5811116206-S projector lamp has been replaced. Resetting the lamp timer without changing the lamp can make it work beyond its recommended hours and cause harm to your Vivitek H1080 projector.

Press the Menu button to open the OSD menu.
Press left/right arrow keys to move to the Setup menu.
Press up/down arrows to move to the Advanced menu
Press Enter.
Press the cursor up/down arrows button to Lamp Hour Reset.
Press Enter.
A message will appear saying the Lamp Hour has been reset to zero.
Press the Menu button to return to the main Setup menu.

Extending the life of the Vivitek 5811116206-S projector lamp:

Keep your air filters clean to avoid overheating the projector.
Use the Lamp Power option on the Vivitek H1081 projector and set to Eco Mode to reduce the amount of power used but extend lamp life.
Learn more with Top tips for extending DLP projector lamp life.

Tagged with: authentic lamps, Vivitek 5811116206-S lamp, Vivitek H1081 projector

NEC M300X projector lamp replacement

Shelagh McNallyPosted on April 8, 2014 Posted in FixYourDLP, Projector Lamp Replacement Guides — 8 Comments ↓

Change the NEC M300X projector lamp hassle free using our handy step-by-step guide.

Buy authentic!

Buying an authentic NEC NP15LP projector lamp will keep your NEC 300X projector working at its best. Avoid a generic NEC M300X projector lamp even though their cheaper price tag is tempting. They have been created using a toxic materials and prone to explosions with a shorter lamp life. Installing them often damages the sensitive electronics in your NEC M300X projector. NOTE: New air filters are shipped with the lamp and it’s recommended you replace them at the same time.

Find this lamp sold on Amazon by these authorized dealers:

Lutema for NEC NP15LP Replacement DLP/LCD Cinema Projector Lamp – Philips Inside
NP15LP NEC NP15LP Projector Lamp
NP15LP – Lamp With Housing For Nec NP-M300X, NP-M260X, M300X, M260X, M260W, NP-M260W, NP-M230X, M260XSG, M260XS, M260WS, M230X Projectors
NP15LP – Lamp With Housing For Nec NP-M300X, NP-M260X, M300X, M260X, M260W, NP-M260W, NP-M230X, M260XSG, M260XS, M260WS, M230X Projectors

When to replace the NEC M300X projector lamp

How will you know the the NEC NP15LP projector lamp needs to be replaced and is reaching end of life? Watch for the following signs:

the LAMP indicator will begin to blink red
message on screen reads LAMP HAS REACHED THE END OF ITS USABLE LIFE. PLEASE REPLACE THE LAMP AND FILTER.
colour looks off
picture is faint or has deteriorated

Checking end of life of the NEC M300X projector lamp

Track the life of the NEC NP15LP lamp with the usage time menu. The progress indicator shows the percentage of remaining bulb life:

Go to INFO menu
Scroll down to USAGE TIME to display the LAMP LIFE REMAINING and LAMP HOURS USED
When the lamp usage reaches 0, the Lamp Life REMAINING starts a count down from 100 hours
When the count down reaches 0, the projector will turn off and not turn on.

Changing the NEC NP15LP projector lamp

Follow these important safety instructions before installing the new NEC NP15LP projector lamp

turn off the NEC M300X projector.
unplug the projector from its power source.
unplug the power cable.
wait until the projector is cool to the touch to avoid getting burned.

Loosen the NEC M300X projector lamp cover screw.

Push and slide the lamp NEC M300X projector lamp cover off.

Loosen the two screws holding the NEC NP15LP projector lamp in place. (The screws will not come out only loosen.

Remove the projector lamp by holding the indent and pulling up.

NOTE: Your NEC NP15LP projector lamp should be properly recycled. These projector lamps contain mercury and can’t be placed into common garbage.

Install a new projector lamp housing the NEC M300X projector, gently pressing the lamp housing into the socket. Take care not to touch the actual bulb as your finger prints can leave oil marks that burn black marks onto the bulb.

Push the top center on the projector lamp to secure it. Tighten the screw on the projector lamp.

Reattach the NEC M300X projector lamp cover by sliding the cover until it snaps into place. Tighten the screw on the lamp cover.

Replacing the filters

There are four filters in the NEC M300X projector:

Honeycomb hard filter – large and small
Accordion soft filter — large and small

Push the catch to release the NEC M300X filter and gently pull it out.

The filter cover is fixed at six separate points in the projector. Bow the filter cover by pushing it slightly until it releases.

Remove the dark sponge filter and clean the filter unit and cover. Attach the new non-woven white material filters.

Filter unit: Attach two honeycomb hard filters to the NEC M300X filter unit.
Filter cover: Attach the two accordion soft filters to the filter cover. Be sure to align the accordion slits with the protrusions of the filter cover.

Attach the filter cover back to the filter unit. Align the filter until with the filter cover and push the protrusions into place. Make sure all the six mounting points are aligned properly.

Insert the two catches of the top of the filter into the groove of the cabinet. Push the filter until it clicks into place.

Reset the projector lamp timer

Once the NEC NP15LP projector lamp and NEC M300X projector filter have both been replaced you will need to reset the timer for both.

Clear usage hours and reset hours

Plug in the power cored into the wall outlet.
Turn on the projector.
From the MENU select RESET.
Choose CLEAR LAMP HOURS.
A confirmation message appears.
Select YES.

Reset the filter hours:

Scroll up to CLEAR Filter HOURS.
A second submenu will appear.
Select YES. Press the ENTER button.

Extending the life of the NEC NP15LP lprojector amp

Auto Mode: 4000 hours
Normal: 5000 hours
Eco ModeL 8000 hours

Learn more tips to extend the life of the NEC NP15LP projector lamp.

Tagged with: authentic lamps, NEC M300X projector, NEC NP15LP lamp

Replacing the Optoma EP716MX projector lamp

Shelagh McNallyPosted on April 8, 2014 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

It’s takes less than 15 minutes to replace the Optoma EP716MX projector lamp. Our guide shows you how.

Your Optoma EP716MX uses the Optoma BL-FU180A (SP.82G01.001) projector lamp. Watch for the warning message that appears on screen letting you know the Optoma EP716MX projector lamp needs replacing.

Watch for these telltale signs that the projector lamp is reaching end of life:

faded image
colours are off or not as vivid
blinking LED lights on the Optoma EP716MX projector

The importance of authentic lamps

Copycat manufacturers offer no guarantee or refunds and the warranty on your Optoma EP716MX projector lamp will become void. Look for the seal of approval before buying and get the best lamp possible — an authentic OEM one!

Why avoid generic lamps:

no safety guards to protect your eyesight.
shorter life so end up costing more.
prone to explosions.
created with toxic substitutes
not operly calibrated
damage the sensitive and expensive electronics optics

Learn how to spot the copycat fake lamps with 7 Ways to Spot a Counterfeit Lamp.

Buy this lamp on Amazon sold by these authorized dealers:

Installing a new Optoma EP716MX projector lamp

Follow these important safety steps before installing a new Optoma BL-FU180A (SP.82G01.001) projector lamp:

Switch off the power to the Optoma EP716MX projector by pressing the Power/Standby button.
Disconnect the power cord.
Allow the projector to cool down for at least 30 minutes. Be sure it is cool to the touch before opening the projector or you could burn yourself badly. These projectors work under extremely high temperatures.

Step 1: Place something soft underneath the Optoma EP716MX and then turn the projector onto it’s back. Remove the two screws holding the cover in place.

Step 2: Push the cover up to remove it.

Step 3: Use a screwdriver to remove the two screws holding the Optoma BL-FU180A (SP.82G01.001) projector lamp module in place.

Slowly put out the old projector lamp by grabbing the edge of the lamp. Be careful not to bang the lamp against the projector as this may case the bulb to break. Learn what to do if the lamp has exploded inside the projector.

NOTE: The used projector lamp contains mercury and should be properly recycled. Don’t throw it into regular garbage.

Step 4: Place the new Optoma BL-FU180A (SP.82G01.001) projector lamp into the Optoma EP716MX projector. Tighten the two screws on the lamp. Replace the lamp cover and tighten its two screws. You must now reset the Lamp Replacement Timer.

Reset the projector lamp timing on the Optoma EP7169MX

The Optoma EP7169MX projector has an automatic projector lamp reset timer that tracks the life of the lamp and triggers the lamp replacement warning. You need to reset the timer each time the lamp is replaced.

Press the Menu option on either the remote or on the projector.
Scroll over the Lamp Setting. Press enter.
Select Reset Lamp Hours. Press Enter
The Execute/Cancel command line will appear.
Scroll over to choose Execute. Press Enter. The lamp hours is reset to zero.

Make the Optoma BL-FU180A (SP.82G01.001) projector lamp last longer with these tips:

Turning on the Eco Mode to lower power consumption and extend the lamp life by 130%.
Keep your air filters clean to avoid overheating the projector.
Turn off the Optoma EP716MX projector and let it stand for at least one hour ever 24 hours.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Top tips for extending DLP projector lamp life

Tagged with: authentic Optoma lamps, Optoma BL-FU180A, Optoma BL-FU180A (SP.82G01.001), Optoma EP716MX

Lamp replacement guide for the Eiki LC-SX4 projector lamp

Shelagh McNallyPosted on April 7, 2014 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Our guide shows you how to replace the Eiki LC-SX4 projector lamp.

The Eiki LC-SX4 projector is equipped with two projection lamps to provide a brighter image. It’s recommended that you change both Eiki POA-LMP39 projector lamps at the same time. Be sure to invest in a Optoma EP716MX projector lamp.

The importance of authentic lamps

Copycat manufacturers offer no guarantee or refunds and the warranty on your Eiki LC-SX4 projector will become void. Look for the seal of approval before buying a projector lamp and get the best projector lamp possible — an authentic OEM one!

6 Reasons for avoiding generic lamps:

generics offer no safety guards to protect your eyesight
generics have a much shorter life so end up costing more
copycat lamps are prone to explosions
fake lamps are created with toxic substitutes
non generic lamps can’t be not properly calibrated
damage the sensitive and expensive electronics optics

Buy authentic Eiki POA-LMP39 projector lamp and save yourself hassles.

Find this lamp sold on Amazon by these authorized dealers:

When to replace the projector lamp

Lamp Mode Changeover: Lamp Management Function automatically changes combination of lighting lamp (Lamp Mode) by detecting status of lamp. When any of the two lamps goes out, Lamp Mode is changed over from 2 lamps to 1 lamp. Lamp Mode can be switched to 2 lamps or 1 lamp manually. Check number of lamp to be replaced on Lamp Status.

Lamp Status

The Lamp Management Function detects status of two lamps and shows the status on screen The lamp status is also displayed for 5 seconds when the projector is turned on. The LAMP REPLACE indicator lights yellow when either lamp is nearing end of life.

On screen status:

ON: Yellow lamp on screen: Lamps are functioning normally.
OFF: Dim Lamp: Projector lamp is turned off and not in use.
NEAR END: Red lamp: Projector lamp is nearing its end. When image becomes darker or color becomes unnatural, replace lamp. (The Lamp replace light on the projector lights yellow at the same time.
OUT: X Mark on lamp: The lamp has reached its end of life and fails to turn on. It may also be defective. Replace lamp corresponding with number marked X.

How to replace the Eiki POA-LMP39 projector lamp

Follow these important safety steps before replacing the Eiki POA-LMP39 projector lamp.

The Eiki LC-SX4 projector operates under very high temperatures. Let it cool for one full hour before attempting to replace the lamp in order to avoid being burned.
Turn off the projector by pressing the power button. Wait for the light to stop flashing.
Turn off the power switch at the back on the projector
Unplug any power cords.

NOTE: To maintain quality of picture (better balance of color and brightness in entire screen), replacing both lamps at the same time.

Loosen the three screws on Lamp Cover and remove Lamp Cover.

Loosen the 2 screws. Using the wire handle and pull out the lamp. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.
Replace the Lamp Assembly. NOTE: The Eiki POA-LMP39 projector lamp contains mercury and should be properly recycled. Don’t place it into regular garbage.
Make sure that Lamp Assembly is set properly. Tighten the 2 screws on the new lamp
Replace Lamp Cover and tighten 3 screws. Connect AC Power Cord to a projector and turn projector on.
Reset Lamp Replacement Counter.

Reset lamp counter

When the Lamp Replace Counter is reset, the LAMP REPLACE indicator stops lighting.
Turn projector on, press MENU button and ON-SCREEN MENU will appear.
Press POINT LEFT/RIGHT button(s) to move the red frame pointer to SETTING Menu icon. Press POINT DOWN button to move a red frame pointer to “Lamp counter reset.”
Press SELECT button.
Move arrow to select either lLamp 1 or Lamp 2. Press SELECT button.

Message “Lamp replace counter Reset?” is displayed.
Move pointer to YES and then press SELECT button.
NOTE: Be sure to reset correct lamp number otherwise LAMP REPLACE indicator continues lighting.
Another confirmation dialog box appears and select YES to reset Lamp Replace Counter.
Do not reset Lamp Replace Counter except after Projection lamp is replaced.

Extend the life of the Eiki POA-LMP39 projector lamp

Get more hours from your Eiki POA-LMP39 projector lamp by following these maintenance tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Eiki LC-SX4 projector and let it stand unused for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life.
Press the MENU button to exit.

Save money, go green

Looking for a green alternative? Try replacing only the projector lamp bulb and re-using the same plastic cage.

Watch this how to video guide to learn more.

Tagged with: authentic lamps, Eiki LC-SX4 projector, Eiki POA-LMP39

Changing the Dell 7609WU projector lamp

Shelagh McNallyPosted on April 4, 2014 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Changing the Dell 7609WU projector lamp is easy when you follow our step-by-step guide.

You’ll know it’s time to replace the Dell 7609WU projector lamp when the lamp light on the Dell 7609WU control panel blinks amber. (It’s number one on the control panel with the light bulb icon.)

The most important thing you can do is to is avoid generics with their much shorter life. Copycat manufacturers also offer no guarantee or refunds. They also creating these knock-off lamps without calibrating them properly so they can damage the sensitive optics in your Dell 7609WU projector. There lamps are also a health hazard. Save yourself hassles and protect your Dell 7609WU projector from being damaged, buy Dell 725-10127 authentic lamps!

To replace the Dell 725-10127 projector lamp

Before replacing the Dell 725-10127 projector lamp be sure to turn the projector off and disconnect from the AC plug. Let the projector cool down for at least 30 minutes. It should be cool to the touch. Don’t attempt to change the lamp when the projector is still hot as there is a good chance you can get severely burned.

Place the Dell 7609WU on a soft surface and turn in upside down to access the lamp cover. Loose the two screws that hold the projector lamp cover in place.
Loosen the two screws that secure the projector lamp.
Pull the projector lamp up by its metal handle. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter. NOTE: Don’t throw the Dell 725-10127 into regular garbage! Since it contains mercury, this lamp must be properly recycled.
Install the new projector lamp.
Tighten the two screws that secure the projector lamp.
Replace the projectorlamp cover and tighten the two screws.

You are now ready to reset the lamp timer.

Resettting the projector lamp counter

The Dell 7609WU projector tracks the life of the Dell 725-10127 projector lamp and will trigger the warning signals when it’s time to replace. Each time you replace the Dell 725-10127 projector lampeset the lamp timer to zero. Failure to do so can result in you using the projector past the optimum lamp life and causing the lamp to explode.

To access the MAIN Menu press the left or right buttons on your projector’s control panel or remote control.
Scroll over the the LAMP submenu. Press ENTER to access.
Press the up or down keys on your projector’s control panel or remote control to scroll down to LAMP RESET.
Scroll over to YES. Press ENTER.

Extend Dell 725-10127 projector lamp life by using some of the options on the LAMP MENU:

POWER SAVING: Set the time the projector waits without an input signal. If there is no signal, the projector will go into power saving mode. The projector will turn back on automatically when it detects and input signal. After two hours of being in power saving mode without a signal, it turns off. The default setting for the Power Saving delay is 12o minutes. However, you can set it to 5, 15, 30, 45, 60, or 120 minutes.

ECO MODE: When on the lamp operates at a lower power level that prolongs the lamp life. Select off to operate at the 300 Watts power level.

QUICK SHUTDOWN: Select Yes to turn off the projector with a single press of the Power button with accelerated fan speed.

Learn more with Top tips for extending DLP projector lamp life.

Save money and go green

Looking for a green alternative? Try replacing only the projector lamp bulb and re-using the same plastic cage.

Watch this how to video guide to see more.

Tagged with: authentic lamps, Dell 725-10127 lamp, Dell 7609WU projector, Dell authentic lamps