RCA-265866 How To Guide Replacement Proyector Lamp Guide

Click below to buy this lamp now:

Lowest Prices Anywhere!

Compatible TV Models: RCA HD44LPW134YX1, RCA HD50LPW164YX2(M1), RCA HD50LPW52YX2(M1), RCA HD61LPW164YX3(M1), RCA HD44LPW164YX1(M1), RCA HD50LPW164YX3, RCA.

Assembly part numbers: 1644987, 1645417, 784050819, 16436090, 7214.

NORMAL DISCLAIMER:
— Do NOT purchase generic brand lamps such as LTI, APO or third-party manufacturers such as OSRAM. These lamps were NOT engineered with and for your TV…only your Philips lamp has been engineered to work flawlessly and output the best possible color. Above that, it just doesn’t make sense to choose an aftermarket lamp for a $5-$10 difference (and in many cases they are more expensive!!).

Be a smart consumer and shop around, do your research! Discount-Merchant.com promises to be the low price leader in all Projection Lamps they carry…if this is not true, let us know and we’ll fix it!

Tools Required: 1 Torx T10 screwdriver (6 point star tip), 1 Torx T8 screwdriver (6 point star tip), 1 Pair of Pliers, & A new lamp.

Time Required: About 15 minutes.

Abstract: This guide is being published to show how easy it is to replace your original RCA 265866 Lamp.

NOTE: We recommend you to use latex gloves when handling the new bulb, to avoid any dirt or oil. Our hands are naturally oily…The oil residue from our hands can cause premature failure of the lamp if the front side of the lamp is not wiped down after the installation. It doesn’t hurt to do a final wipe with a clean, non-abrasive, lint-free cloth before reinstalling your lamp…

	RCA 265866 Lamp casing			1.- To begin, turn the lamp facedown so it will look like this.
	2.- Unscrew the nut on the top of the lamp, with help of a pair of pliers.			3.- Use a Torx T10 screwdriver, and remove the screw that is holding the cable to the side of the lamp.
	4.- Using a Torx T8 screwdriver, uninstall the screws holding the lamp vent.			5.- Remove the second screw holding the first lamp vent.
	6.- Repeat same steps to the second lamp vent.			7.- Now your lamp vents are free and safe to be remove.
	8.- Uninstall booth lamp vents.			9.- Remove your old lamp, by pulling it out.
	A.- Take out your new bulb and reinstall it, the same way you took out the old bulb.			B.-Install your new PHILIPS E22 UHP 100W/120W 1.0 lamp to the lamp holder.
	C.- Place back the lamp vents to their original position.			D.- Place them carefully preventing damage on the lamp.
	E.- Secure the lamp vent by putting back the screws with a Torx T8 screwdriver.			F.- Repeat same step to the second lamp vent.
	G.- Reconnect the cable to the side of the lamp using the Torx T10 screwdriver.			H.- Reinstall the cable to the top of the lamp by tightening the nut with a pair of pliers.
	I.- And it will look like this.			J.-And you’re finished, Congratulations!

IMPORTANT: After installing the replacement bulb, you should wipe it with a clean cloth to avoid any dirt or oil. Our hands are naturally oily…this could reduce considerably the life span of the new lamp.

Again, Discount-Merchant.com promises to be the low price leader in all Projection TV Lamps they carry…if this is not true, let us know and we’ll fix it

Click below to buy this lamp now:

Lowest Prices Anywhere!

RCA Lamp RCA-265866 How-To Replacement Guide