Below are a few snapshots…as more information becomes available we will update this page.

Let us know if you have any information on compatibility, etc.

The new JVC replacement lamp, PK-CL120U, is currently compatible with all the latest 2008 model TVs, including the ultra slim:

HD-65S998 (65" HDILA D-ILA TV) Here’s the user manual for your conveience and reference
HD-58S998 (58" HDILEA D-ILA TV) Here’s the user manual for your conveience and reference

(Please note, the HD-70GC78, although a current generation model, it still uses the older TS-CL110UAA lamp and is not covered in this review)

These new 2008 models, first displayed at the Internation Consumer Electronics Show (CES 2008) are 40% thinner than the average rear projection TV, and actually 43% thinner than JVC’s own previous generation models which featured the TS-CL110UAA lamp. These new TVs are under 12" (actually 10.7" and 11.6" respectfully) and can be wall mounted thanks to the standard VESA mounting, as well as the attractive and sleek from bezel.

The new PK-CL120U user replacement lamp in these JVCs are made by Philips..

The new Ultra Slim TVs are 1080P HD-ILA with a new 2 Million Pixel Structure 0.7″ 3-Chip design. this is the 5th Generation D.I.S.T. with GENESSA and all feature Energy Star compliant circuitry.

Additional Features:
No hassle HD with built-in ATSC tuner and Clear QAM
User replaceable lamp (PK-CL120U)
Dual HDMI w/HDCP Digital Video Inputs

As you can see below, the new lamp is manufactured by Philips Lighting…this is a big positive move on the part of JVC to insure more reliable sets! No longer should JVC fans be discouraged by unreliable UHP lighting!

Philips 100W / 120W 1.0 lamp…

Note this UHP Philips lamp does not have a front glass and resembles more like a typical projector bulb with is small size.

This makes the lamp extremely sensative! If the filament is touched, that could be the end of your bulb…be careful!

Another view of the new Philips JVC Lamp

As you can see, the front cover extends out a bit and give the lamp a little bit of breathing room. The previous generation TVs using the TS-CL110UAA lamp featured a sealed UHP lamp. The new design should allow for better heat dissipation and longer life.

the bulb enclosure has a more aggressive look to it too..hehe..

Share your comments with us!

It’s a terrible feeling… it sucks when you’re anticipating watching your favorite program and “pop,” the lamp in your projection TV fails

Why did it happen? You were just watching TV, it’s not like you were wrestling with it! Why?!?

In our experience, there are a number of factors that can contribute to a premature lamp failure. Keep in mind that there is no fail-safe course of action you can take… these lamps are consumable products… they are designed to need replacing. Nevertheless, there are a few things you can do to insure your lamp has a healthy and long life. The following list is made in order of importance (remember, there is no scientific data yet behind this, just years of experience).

• AVOID Rapid Power Cycling

  Turning on the set, turning it off, turning it on, turning it off… turning it on… turning if off. This is absolutely the worse thing one can do to their TV. If you turn on the TV accidentally, give it a good 15-20 minutes to warm up before turning it down.

• AVOID Excessive Power Cycles

  A power cycle happens every time you press the power button on your remote to turn it on. Think of it as your car starter. Imagine an insanely busy pizza delivery boy who has 50 deliveries a day. Every time he leaves the pizza shop he needs to activate his car starter…every time he leaves a customer’s house, he needs to activate his starter again. There is a good chance this poor guy’s starter (100 starts a day!) is going to fail sooner than someone with an 9 to 5 office job, who starts his/her car once in the morning, once in the afternoon, and once in the evening. The same concept applies here. Do not power cycle your TV set every half hour thinking you’re going to save 10 minutes of lamp life–it doesn’t work that way. You’re doing more damage “sparking” or “striking” the lamp. In short: it’s better to keep the TV on for 5 hours straight rather than watch a one hour program and turn it off only to turn it back on half an hour later.

• AVOID Dust and Dirt

  I cannot stress this enough. Eliminating dust and dirt is another very important aspect of maintaining a healthy projection TV. Take a look at the back of your TV; there is a good chance there’s a lot of dust sitting on the back of the TV. Wipe your finger across the back and you’ll see. With so much dust on the outside of the TV you can imagine some of it must be getting into inside, and as a result, shortening your lamp life. After 5,000+ lamps replaced, I can honestly say maintaining a clean and dust free TV is essential to promoting a long life.

  My recommendations:

• Wipe down the back of your TV once a month with a damp cloth
• Invest ~ $100 in a ionic air purifier and place it close to the TV. This will silently attract all the dust, pollen, smoke, etc. away from the TV set. Do NOT take a can of compressed air and go nuts spray air everywhere inside your TV! In general, these ionic purifiers are practical and good to have anyway. http://www.ionicpro.com/howitworks.html . I use this particular one in the office
• Clean out all of the television’s filters or use a can of compressed air to remove excess dust.

• Surge Protectors

  These are good and bad, but ultimately good if used properly. The manufacturer’s typically recommend against plugging our TVs into surge protectors. Why? Because they are afraid customers might get accustomed to turning off their TVs this way (which is a big no no!). Most projectors and projector TVs need a cool down period after they are shutdown. Most of the time, there is a silent fan running. If there is no power, the fan stops working!

  Surge protectors are important as sudden spikes in voltage can fry your ballast and/or lamp. If your lamp made the infamous “pop” noise, recall seeing if you had a surge protector inline.

• Ventilation and Filters

  Ensure your TV has adequate ventilation. Most sets have at least a vent or fan close by to the lamp. Some have filters. Make sure that the filter is clean. Replace or clean the filter per the manufacturer’s recommendations.

• DO NOT Touch the Lamp

  Never touch the lamp with your bare hands. Our hands are naturally oily and body oil cause “hot spots” on the lamp which may lead to explosions, implosions, or cracks. Always use a clean, non-abrasive, lint free cloth when handling your lamp.

• Movement and Vibration

  Ever moved your TV and noticed it didn’t fire up the first time? Have you noticed a scrambled or distorted picture when adjusting your TV Stand while the TV has been on? What about everyday vibrations of powerful home theater systems? All these can lead to the lamp, light engine, color wheel, etc, etc., from losing alignment. There’s been dozens of times when we’ve fixed a “lamp problem” by just re-seating the lamp or adjusting the lamp cover sensor. All the above recommendations are intuitive suggestions. There isn’t any scientific research behind it, but through experience we know that they play some factor in the life of your lamp. I have not mentioned anything about picture brightness or power settings because there is much debate over this. Some claim by putting your lamp in economy mode or low power this will result in longer lamp life. On the contrary, we believe these options do not promote longer lamp life!

Hope these tips help. Send us your feedback!