The lamp on your Sanyo PLC-XU305/PLC-XU355 projector should last between 1,000 to 2,000 hours before needing to be replaced. The lifespan of the lamp will vary depending on how much the projector is ]]>

Sanyo PLC-XU355 Projector

The lamp on your Sanyo PLC-XU305/PLC-XU355 projector should last between 1,000 to 2,000 hours before needing to be replaced. The lifespan of the lamp will vary depending on how much the projector is used and if the filters are cleaned regularly.

When your POA-LMP131 projector lamp is nearing its end of life you’ll see the Replace Lamp icon appear on the screen and the Lamp Replace Indicator will start flashing red. Depending on the Lamp Mode chosen, the Sanyo PLC-XU305/PLC-XU355 projector may turn off after three minutes.

Invest in an authentic POA-LMP131 and avoid the temptation to buy a cheaper priced lamp. These bargain lamps are usually counterfeit lamps and use inferior parts that can damage your projector. They may end up costing you more in the long run. Authentic lamps have been manufactured with reliable parts that work with the sensitive mechanismsin your Sanyo PLC-XU305/PLC-XU355 projector. These authentic lamps come with a guarantee and won’t make your projector’s warranty invalid.

STEP-BY-STEP INSTRUCTIONS FOR SANYO PLC-XU305/PLC-XU355 LAMP REPLACEMENT

Sanyo PLC-XU305 Projector

NOTE: These instructions can also be applied to the Sanyo PLC-XU305K and PLC-XU355K projectors.

Before installation: Turn off the projector and unplug the AC cord. Allow 45 to 60 minutes for the Sanyo PLC-XU305/PLC-XU355 projector to be cool to the touch. Don’t open the projector when hot since these machines operate under high temperatures and you can burn yourself.

Replacing the POA-LMP131 Lamp Assembly

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

1. The lamp cover for the Sanyo PLC-XU305/PLC-XU355 is located at the top of the projector. Locate the screw holding the lamp cover in place found on the side over top of the ventilation holes. Loosen the screw to remove the cover.

2. Inside there are three screws holding the POA-LMP131 lamp in place. Remove all three screws.  Grab the handle on the lamp cage and gently remove the lamp. Place to one side. Be sure to dispose of the lamp properly through a local recycling program.

3. Take the new POA-LMP131 lamp cage by the handle and gently maneuvere it into place. Avoid touching the glass or the bulb. The lamp should slide in easily – don’t force it.

4. Once the lamp is in, tighten all three screws on the Lamp Assembly. Make sure the screws have been tightened properly or the projector will not turn on.

5. Replace the Lamp Cover and tighten the screw.

6. Re-connect the power cord and turn on the Sanyo PLC-XU305/PLC-XU355 projector. If the lamp does not turn on after the warm-up period, try re-installing the lamp. Reset the lamp hour using the Lamp Control mode found on the Setting menu.

NOTE: Your old lamp should be properly recycled. These lamps contain mercury and can’t be placed into common garbage.

RESETTING THE SANYO PLC-XU305/PLC-XU355 LAMP CONTROL MODE

Reset the Lamp Control Mode only when POA-LMP131 lamp has been replaced.  Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Note: You must wait for at least 10 minutes before changing the Lamp Control mode since the newly installed lamp will need time to stabilize. While your waiting, take the time to clean the air filter as this can extend the life of your newly installed lamp.

Sanyo PLC-XU305/PLC-XU355  projectors have a Lamp control that allows you to change the brightness of the screen and extend the life of your lamp.

Normal mode allows for normal brightness

Eco mode lowers the brightness reducing consumptions thereby extending the lamp life.

To change the mode for the total lighting time:

1. Scroll down to the Setting option. Select Lamp Control. A second screen will appear

2. There are two two modes for Lamp life control. Mode 1 lets the lamp be turned on even after exceeding the recommended total hours of use. Mode 2 lets the lamp be turned on even after exceeding the recommended total hours BUT the projector turns off automatically after 3 minutes.

NOTE: When you reset the Lamp Mode, the Lamp Indicator will stop blinking and the on screen Lamp Icon will disappear.

Turn the Sanyo PLC-XU305/PLC-XU355 projector on and let the lamp stabilize before using.

Prolong the life of your new POA-LMP131 lamp by regular cleaning the the air filter.

Replace the lamp immediately when the Indicator’s yellow light is blinking. When the POA-LMP115 projector lamp is approaching end of life, you’ll see the blinking light on the Sanyo PLC-XU88 projector.

Only genuine POA-LMP115 lamps ]]>

Sanyo PLC-XU88 Projector

Replace the lamp immediately when the Indicator’s yellow light is blinking. When the POA-LMP115 projector lamp is approaching end of life, you’ll see the blinking light on the Sanyo PLC-XU88 projector.

Only genuine POA-LMP115 lamps should be used in order to keep your projector is good working order. The authentic POA-LMP115 has been manufactured to meet the specifications of the Sanyo PLC-XU88.

While knock-off lamps may seem like a bargain due to their low prices, these counterfeit lamps can damage the sensitive and expensive mechanismsin your Sanyo XU88 projector. Your guarantee on your Sanyo PLC- XU88 projector may also be void if you use a counterfeit POA-LMP115 projector lamp.

STEP-BY-STEP INSTRUCTIONS FOR POA-LMP115 LAMP REPLACEMENT

Before installation of the POA-LMP115 lamp: Turn off the projector and unplug the AC cord. The Sanyo PLC-XU88 projector should be cool to the touch before you replace the projector lamp. It usually takes one hour for the projector to fully cool since these projectors operate under high temperatures.

Do not operate the projector while any of the lamps are removed as this may result in malfunctions and may be a fire hazard.

Replacing the POA-LMP115 lamp

Caution: Avoid creating black spots on the projector lamp. Don’t touch the screen or the actual bulb with your finger or hands. Oil from your hands can damaged the lamp.

1. The lamp cover is found underneath the Lamp cover Sanyo PLC-XU88 projector. Gently turn it upside, making sure to protect the top of the projector. Using a screwdriver loosen the screw holding the cover in place. Put the cover to one side.

2. Inside will be the lamp projector cage. Remove the two screws on either side of the POA-LMP115 lamp. Grab the handle on the lamp cage and gently pull out the lamp. Place to one side. You’ll need to recycle the old lamp.

3. Grab then handles of the POA-LMP115 lamp cage and gently maneuvere it into place. Avoid touching the glass or the bulb. The lamp should slide in easily – don’t force it.

4. Once the lamp is in, tighten the screws on the Lamp Assembly.

5. Replace the Lamp Cover and tighten the screw.

6. Re-connect the power cord and turn on the Sanyo PLC-XU88 projector. You’ll need to reset the lamp replacement counter.

Resetting the Lamp Replacement counter on the Sanyo PLC-XU88 Projector

NOTE: Reset the Lamp Replacement Counter only when the POA-LMP115 lamp has been replaced.

• Turn the Sanyo PLC-XU88 projector on.
• Press the Menu option to display the On-Screen Menu.
• Press the left/right button(s) to move to the Setting Menu icon.
• Press the Point Down button to move to Lamp Counter Reset.
• Press the Select button.

• When the next confirmation dialog box appears, press select.
•  The Lamp box will disappear and the Lamp Replace Dialog box appears.
• Select YES to reset Lamp Replace Counter.

NOTE: When you reset the Lamp Replace Counter the Lamp Replace indicator stops blinking.

Clean your filter before before using the Sanyo PLC-XU788 projector to ensure a longer life for your newly installed POA-LMP115 projector lamp.

When it’s time to change your lamp on your  PLC-XF30/ PLC-XF30NL/PLC-XF31 projector, you’ll notice the yellow light blinking on the lamp indicator.

Sanyo PLC-XF30NL Projector

Be sure to use the same type of ]]>

Sanyo PLC-XF31 Projector

When it’s time to change your lamp on your  PLC-XF30/ PLC-XF30NL/PLC-XF31 projector, you’ll notice the yellow light blinking on the lamp indicator.

Sanyo PLC-XF30NL Projector

Be sure to use the same type of Sanyo projector lamp bought from a verified source that has been manufactured to meet the specifications. Use model POA-LLB02 or POA-LMP39 as your Sanyo projector lamp replacement. Resist the temptation to buy a cheaper POALLBO2 or POA-LMP39 counterfeit model as this can damage the sensitive mechanisms in your Sanyo PLCXF30/PLCXF31 projector.

STEP-BY-STEP INSTRUCTIONS FOR PLCXF30/PLCXF31 Lamp Replacement

Before installation

1. Check the number of lamp to be replaced on the Lamp Status Display.
2. Turn off the projector and unplug the AC cord.
3. Allow the Sanyo PLCXF30/ PLCXF30NL/PLCXF31 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures.

Replacing the POA-LLB02/POA-LMP39 Lamp Assembly

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

1. At the back of the Sanyo PLCXF30/ PLCXF30NL/PLCXF31 projector you’ll find the Lamp Hazard cover. Using a Philips screwdriver loosen the three screws that hold the cover in place. Put the cover to one side.
2. Remove the two screws on either side of each of  the POALLB02 or POA-LMP39 lamp. Grab the handle on the lamp cage and gently pull out each lamp. Place those lamps to one side.

3. Take the new POALLB02 or POA-LMP39 lamp cage by the handle and gently maneuvere it into place.

4. Avoid touching the glass or the bulb. It should slide it easily – don’t force it.
5. Tighten the screws on the Lamp Assembly.
6. Replace and tighten the three screws on either side of Lamp Hazard Cover.
7. Re-connect the power cord and turn on the Sanyo PLCXF30/ PLCXF30NL/PLCXF31 projector.

Reset Sanyo PLCXF30/ PLCXF30NL/PLCXF31 Lamp Replacement Counter

Reset the Lamp Replacement Counter only when the POA-LLB02 or POA-LMP39 lamp has been replaced.

Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

• Turn the Sanyo PLCXF30/ PLCXF30NL/PLCXF31 projector on.
• Press the Menu option so the On-Screen Menu will appear.
• Press Point left/right button(s) to move a red frame poster to Setting Menu icon.
• Press Point Down button to move the red frame pointer to Lamp counter reset.
• Press the Select button.
• Move arrow to replace lamp number (Lamp 1 or Lamp 2) and then press Select button. The message “Lamp replace counter Reset?” will be displayed.
• Move the pointer to YES and then press Select button.
• Be sure to reset the correct lamp number otherwise Lamp Replace indicator continues lighting.

• The Lamp box will disappear and the Lamp Replace Dialog box appears.
• Select YES to reset Lamp Replace Counter.
• Do not reset Lamp Replace Counter except after the Projection Lamp has been replaced.
• NOTE: When you reset the Lamp Replace Counter the Lamp Replace indicator stops lighting.

Clean your filter before turning on the PLC-XF30/ PLCX-F30NL/PLC-XF31 projector and you’re good to go.