Sanyo PLC-XW300 Projector

STEP-BY-STEP INSTRUCTIONS FOR SANYO PLC-XW300 LAMP REPLACEMENT

When your Sanyo POA-LMP132 (service parts no 610 345 2456) projector lamp is nearing its end of life you’ll see the  Lamp Replace Indicator on the projector flash yellow.

The Replace Lamp icon will also appear on the projector screen.

The lifespan of your Sanyo POA-LMP132 (service parts no 610 345 2456) lamp will vary depending on how much the projector is used and if the filters are cleaned regularly.

Before installation:

Buy your Sanyo POA-LMP132 (service parts no 610 345 2456) from an authorized manufacturer and avoid the lower-priced knock-off lamps. These fake lamps are usually made with counterfeit parts that are inferior and can damage the sensitive mechanisms in your Sanyo PLC-XW300 projector. They may end up costing you more if they damage your projector since they also void your warranty. Buying from a legitimate source keeps your projector under warranty and gives you a solid guarantee that the lamp you are installing is suitable for your projector.

For additional savings, you can replace only the POA-LMP132 bulb and keep the original lamp cage. Watch our video guide and learn how.

Replacing the POA-LMP132 Lamp Assembly

1. Safety steps:

• Turn off the projector and unplug the AC cord.
• Allow the Sanyo PLC-XW300 projector to cool to the touch. This can take between 45 to 60 minutes. Don’t open the projector when its still hot since these machines operate under high temperatures and you can burn yourself.

2. Remove the lamp cover for the  Sanyo PLC-XW300—it’s  located at the top of the projector towards the back. Locate the screw holding the lamp cover in place found on the side over top of the ventilation holes. Loosen the screw to remove the cover.

3. Inside you’ll find the Sanyo POA-LMP132 (service parts no 610 345 2456) lamp cage. Loosen all three screws holding the lamp cage in place. Grab the handles on the lamp cage and gently lift the lamp out of its socket. Place to one side. Be sure to dispose of the lamp properly through a local recycling program.

4. Take the new Sanyo POA-LMP132 (service parts no 610 345 2456) lamp cage by the handle—avoid touching the lamp surface as oil from your fingers can cause black spots to appear when the projector is turned on. Gently maneuver the lamp into place. Don’t force the lamp as this may damage it.

5. Tighten all three screws on the Sanyo POA-LMP132 (service parts no 610 345 2456) Lamp Assembly. Make sure the screws have been tightened properly or the Sanyo PLC-XW300  projector will not turn on. Replace the Lamp Cover and tighten the screw.

6. Re-connect the power cord and turn on the Sanyo PLC-XW300. If the lamp does not turn on after the warm-up period, try re-installing the lamp. Reset the lamp hour using the Lamp Control mode found on the Setting menu.

NOTE: Your old Sanyo POA-LMP132 (service parts no 610 345 2456) lamp should be properly recycled. These lamps contain mercury and can’t be placed into common garbage.

RESETTING THE SANYO PLC-XW300 LAMP CONTROL MODE

Resetting the lamp replacement counter will ensure your projector correctly tracks the hours left in your newly installed Sanyo POA-LMP132 (service parts no 610 345 2456) lamp.

• Turn the Sanyo PLC-XW300 projector on.
• Press the Menu option to display the On-Screen Menu.
• Press Point left/right button(s) to move a red frame poster to Setting Menu icon.
• Press the black arrow point button to move the red framed pointer to the Setting Menu Icon.
• Press Point Down button to move the red frame pointer to Lamp counter reset.
• Press the Select button.
• Another confirmation dialog box appears, select YES.
• The Lamp box will disappear and the Lamp Replace Dialog box appears.
• Select YES to reset Lamp Replace Counter.

• There are two modes for Lamp life control. Mode 1 lets the lamp be turned on even after exceeding the recommended total hours of use. Mode 2 lets the lamp be turned on even after exceeding the recommended total hours BUT the projector turns off automatically after 3 minutes.
• The Sanyo PLC-XW300 projector has a Lamp control that allows you to change the brightness of the screen and extend the life of your lamp. High Mode: Brighter than the Normal mode. It will shorten the lamp life using this mode. Normal Mode: Normal brightness. Eco Mode: Lowers the brightness and reduces the lamp power consumption thereby extending the lamp life.  NOTE: When you reset the Lamp Replace Counter the Lamp Replace indicator stops lighting.

Prolong the life of your new POA-LMP132 lamp

You can prolong the life of your newly installed Sanyo POA-LMP132 (service parts no 610 345 2456) lamp by:

• regular cleaning the the air filter
• allowing the Sanyo PLC-XW300 projector to stand for five minutes per turning the projector off.
• wait at least five minutes before turning the Sanyo PLC-XW300 projector off.
• don’t operate the projector continuously without letting it stand for at least one hour
• turned off every 24 hours
  

The post 6 Steps to replacing the Sanyo PLC-XW300 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Sanyo PLC-XW200 Projector

STEP-BY-STEP INSTRUCTIONS FOR PLC-XW200/ PLC-XW250 LAMP REPLACEMENT

When your Sanyo POA-LMP132 (service parts no 610 345 2456) projector lamp is nearing its end of life you’ll see the  Lamp Replace Indicator on the projector flash yellow and the Replace Lamp icon appear on the projector screen.

The lifespan of your Sanyo POA-LMP132 (service parts no 610 345 2456)  lamp will vary depending on how much the projector is used and if the filters are cleaned regularly.

Before installation

Buy your  Sanyo POA-LMP132 (service parts no 610 345 2456) from an authorized manufacturer and avoid the lower-priced knock-off lamps. These counterfeit lamps are usually made with inferior parts that can damage your projector; they may end up costing you more if they damage the  sensitive mechanisms in your Sanyo PLC-XW200/ PLC-XW250 projector. Buying from a legitimate source keeps your projector under warranty and gives you a solid guarantee.

For additional savings, you can replace only the POA-LMP132 bulb and keep the original lamp cage. Watch our video guide and learn how.

Replacing the Sanyo POA-LMP132 Lamp Assembly

NOTE: These instructions can also be applied to the Sanyo PLC-XW200K/ PLC-XW250K projectors.

1. Turn off the projector and unplug the AC cord. Allow the Sanyo PLC-XW200/ PLC-XW250 projector to cool for 45 to 60 minutes. Opening the projector while still hot is dangerous due to the high temperatire. You can burn yourself badly.

2. Remove the lamp cover for the  Sanyo PLC-XW200/ PLC-XW250—it’s  located at the top of the projector towards the back. Locate the screw holding the lamp cover in place found on the side over top of the ventilation holes. Loosen the screw to remove the cover.

3. Inside you’ll find the Sanyo POA-LMP132 (service parts no 610 345 2456) lamp cage. Loosen all three screws holding the lamp cage in place. Grab the handles on the lamp cage and gently lift the lamp out of its socket. Place to one side. Be sure to dispose of the lamp properly through a local recycling program.

4. Take the new Sanyo POA-LMP132 (service parts no 610 345 2456) lamp cage by the handle—avoid touching the lamp surface as oil from your fingers can cause black spots to appear when the projector is turned on. Gently maneuver the lamp into place. Don’t force the lamp as this may damage it.

5. Once the lamp is in, tighten all three screws on the Sanyo POA-LMP132 (service parts no 610 345 2456) Lamp Assembly. Make sure the screws have been tightened properly or the Sanyo PLC-XW200/ PLC-XW250  projector will not turn on.

6. Replace the Lamp Cover and tighten the screw. Re-connect the power cord and turn on the Sanyo PLC-XW200/ PLC-XW250 projector. If the Sanyo POA-LMP132 (service parts no 610 345 2456) lamp does not turn on after the warm-up period, try re-installing the lamp.

Reset the lamp hour using the Lamp Control mode found on the Setting menu.

NOTE: Your old Sanyo POA-LMP132 (service parts no 610 345 2456) lamp should be properly recycled. These lamps contain mercury and can’t be placed into common garbage.

RESETTING THE SANYO PLC-XW200/ PLC-XW250 LAMP CONTROL MODE

Resetting the lamp counter will ensure your projector accurately tracks the hours left in your newly installed Sanyo POA-LMP132 (service parts no 610 345 2456)) lamp.

• Turn the Sanyo PLC-XW200/ PLC-XW250 projector on.
• Press the Menu option to display the On-Screen Menu.
• Press Point left/right button(s) to move a red frame poster to Setting Menu icon.
• Press the black arrow point button to move the red framed pointer to the Setting Menu Icon.
• Press Point Down button to move the red frame pointer to Lamp counter reset.
• Press the Select button.

• Another confirmation dialog box appears, select YES.
• The Lamp box will disappear and the Lamp Replace Dialog box appears.
• Select YES to reset Lamp Replace Counter.
• There are two modes for Lamp life control. Mode 1 lets the lamp be turned on even after exceeding the recommended total hours of use. Mode 2 lets the lamp be turned on even after exceeding the recommended total hours BUT the projector turns off automatically after 3 minutes.

• The  Sanyo PLC-XW200/ PLC-XW250 has a Lamp control that allows you to change the brightness of the screen and extend the life of your lamp. High Mode: Brighter than the Normal mode. It will shorten the lamp life using this mode. Normal Mode: Normal brightness. Eco Mode: Lowers the brightness and reduces the lamp power consumption thereby extending the lamp life.

NOTE: When you reset the Lamp Replace Counter the Lamp Replace indicator stops lighting.

Prolong the life of your new Sanyo POA-LMP132 (610 345 2456) lamp

To maintain the life of your newly installed Sanyo POA-LMP132 (service parts no 610 345 2456), wait at least five minutes before turning the Sanyo PLC-XW200/ PLC-XW250 projector off. Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours. Regular cleaning of the air filter will also prolong lamp life.

The post Easy instructions for replacing the Sanyo PLC-XW200/ PLC-XW250 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Sanyo PLC-XR301 Projector

The lamp on your Sanyo PLC-XR301 projector should last between 1,000 to 2,000 hours depending on the usage and regular maintenance.

When the Sanyo POA-LMP132 (service parts no 610 345 2456) projector lamp is nearing its end of life you’ll see the Replace Lamp icon appear on the projector screen and the Lamp Replace Indicator will begin flashing yellow. Depending on the Lamp Mode chosen, the Sanyo PLC-XR301 projector may also  turn off after three minutes.

Be sure to buy an authentic Sanyo POA-LMP132 (service parts no 610 345 2456) from an authorized manufacturer. Knock-off lamps may be cheaper in the beginning but since these lamps are usually made with counterfeit parts that can damage your projector–they may end up costing you more in the long run. Authentic lamps have been manufactured with reliable parts that work with the sensitive mechanisms in your Sanyo PLC-XR301 projector. They also come with a guarantee and won’t void your projector’s warranty.

The lifespan of your Sanyo POA-LMP132 (service parts no 610 345 2456)  lamp will vary depending on how much the projector is used and if the filters are cleaned regularly.

For additional savings, you can replace only the POA-LMP132 bulb and keep the original lamp cage. Watch our video guide and learn how.

STEP-BY-STEP INSTRUCTIONS FOR SANYO PLC-XR301 LAMP REPLACEMENT

Before installation: Turn off the projector and unplug the AC cord. Allow the Sanyo PLC-XR301 projector to cool to the touch. This may take between 45 to 60 minutes. Don’t open the projector when hot since these machines operate under high temperatures and you can burn yourself.

Replacing the Sanyo POA-LMP132 (610 345 2456) Lamp Assembly

1. Remove the lamp cover for the  Sanyo PLC-XR301—it’s  located at the top of the projector towards the back. Locate the screw holding the lamp cover in place found on the side over top of the ventilation holes. Loosen the screw to remove the cover.

2. Inside you’ll find the Sanyo POA-LMP132 (service parts no 610 345 2456) lamp cage. Loosen all three screws holding the lamp cage in place. Grab the handles on the lamp cage and gently lift the lamp out of its socket. Place to one side. Be sure to dispose of the lamp properly through a local recycling program.

3. Take the new Sanyo POA-LMP132 (service parts no 610 345 2456) lamp cage by the handle—avoid touching the lamp surface as oil from your fingers can cause black spots to appear when the projector is turned on. Gently maneuver the lamp into place. Don’t force the lamp as this may damage it.

4. Once the lamp is in, tighten all three screws on the Sanyo POA-LMP132 (service parts no 610 345 2456) Lamp Assembly. Make sure the screws have been tightened properly or the Sanyo PLC-XR301 projector will not turn on.

5. Replace the Lamp Cover and tighten the screw.

6. Re-connect the power cord and turn on the Sanyo PLC-XR301 projector. If the Sanyo POA-LMP132 (service parts no 610 345 2456)lamp does not turn on after the warm-up period, try re-installing the lamp. Reset the lamp hour using the Lamp Counter mode found on the Setting menu.

NOTE: Your old Sanyo POA-LMP132 (service parts no 610 345 2456) lamp should be properly recycled. These lamps contain mercury and can’t be placed into common garbage.

RESETTING THE SANYO PLC-XR301 LAMP COUNTER

Resetting the Lamp Control Mode will ensure your projector tracks the hours in your Sanyo POA-LMP132 (service parts no 610 345 2456) accurately.

• Turn the Sanyo PLC-XR301 projector on.
• Press the Menu option to display the On-Screen Menu.
• Press Point left/right button(s) to move a red frame poster to Setting Menu icon.
• Press the black arrow point button to move the red framed pointer to the Setting Menu Icon.
• Press Point Down button to move the red frame pointer to Lamp counter reset.
• Press the Select button.

• Another confirmation dialog box appears, select YES.
• The Lamp box will disappear and the Lamp Replace Dialog box appears.
• Select YES to reset Lamp Replace Counter.

• There are two modes for Lamp life control. Mode 1 lets the lamp be turned on even after exceeding the recommended total hours of use. Mode 2 lets the lamp be turned on even after exceeding the recommended total hours BUT the projector turns off automatically after 3 minutes.
• The Sanyo PLC-XR301 projector has a Lamp control that allows you to change the brightness of the screen and extend the life of your lamp. High Mode: Brighter than the Normal mode. It will shorten the lamp life using this mode. Normal Mode: Normal brightness. Eco Mode: Lowers the brightness and reduces the lamp power consumption thereby extending the lamp life.

NOTE: When you reset the Lamp Replace Counter the Lamp Replace indicator stops lighting.

Prolong the life of your new Sanyo POA-LMP132  (610 345 2456) lamp

Prolong the life of your new Sanyo POA-LMP132 (service parts no 610 345 2456) lamp by:

• regular cleaning the the air filter
• allow the Sanyo PLC-XR301 projector to stand for five minutes per turning the projector off.
• don’t operate the projector continuously without letting it stand for at least one hour every 24 hours.
  

The post How to replace the projector lamp in the Sanyo PLC-XR301 projector appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Sanyo PLC-XR251 projector

When the Sanyo POA-LMP132 (service parts no 610 345 2456) nears the end of life, the Lamp life control menu will begin blinking yellow on your Sanyo PLC-XR201/PLC-XR251 projector. The Lamp replacement icon will also appear on screen. If Mode 2 has been selected in the Lamp life control menu, the projection will turn off automatically after 3 minutes as soon as the Lamp Replacement icon appears.

Replace the Sanyo POA-LMP132 (service parts no 610 345 2456) immediately with a guaranteed authentic lamp. Be sure to verify that your lamp is authentic and buy from an authorized manufacturer. If the price of the lamp you’re about to buy seems like an incredible bargain, chances are it’s counterfeit and has been created using inferior parts that can damage the inside of your projector since it will not fit properly. Buying a knock-off lamp will also void your warranty and should anything happen to the projector you will not be covered.

The lifespan of your Sanyo POA-LMP132 (service parts no 610 345 2456)  lamp will vary depending on how much the projector is used and if the filters are cleaned regularly. To maintain the life of your lamp, wait at least five minutes before turning it off. Don’t operate the projector continuously without letting it stand for at least one hour every 24 hours.

STEP-BY-STEP INSTRUCTIONS FOR PLC-XR201/PLC-XR251 LAMP REPLACEMENT

Before installation: Turn off the projector and unplug the AC cord. Allow the Sanyo PLC-XR201/PLC-XR251 projector to cool to the touch. This can tke between 45 to 60 minutes. Don’t open the projector when hot since these machines operate under high temperatures and you can burn yourself.

Replacing the Sanyo POA-LMP132 Lamp Assembly

1. Remove the lamp cover for Sanyo PLC-XR201/PLC-XR251 projector—it’s  located at the top of the projector towards the back. Locate the screw holding the lamp cover in place found on the side over top of the ventilation holes. Loosen the screw to remove the cover.

2. Inside you’ll find the Sanyo POA-LMP132 (service parts no 610 345 2456) lamp cage. Loosen all three screws holding the lamp cage in place. Grab the handles on the lamp cage and gently lift the lamp out of its socket. Place to one side. Be sure to dispose of the lamp properly through a local recycling program.

3. Take the new Sanyo POA-LMP132 (service parts no 610 345 2456) lamp cage by the handle—avoid touching the lamp surface as oil from your fingers can cause black spots to appear when the projector is turned on. Gently maneuver the lamp into place. Don’t force the lamp as this may damage it.

4. Once the lamp is in, tighten all three screws on the Sanyo POA-LMP132 (service parts no 610 345 2456) Lamp Assembly. Make sure the screws have been tightened properly or the Sanyo PLC-XR201/PLC-XR251 projector will not turn on.

5. Replace the Lamp Cover and tighten the screw.

6. Re-connect the power cord and turn on the Sanyo PLC-XR201/PLC-XR251. If the Sanyo POA-LMP132 (service parts no 610 345 2456) lamp does not turn on after the warm-up period, try re-installing the lamp. Reset the lamp hour using the Lamp Control mode found on the Setting menu.

NOTE: Your old Sanyo POA-LMP132 (service parts no 610 345 2456) lamp should be properly recycled. These lamps contain mercury and can’t be placed into common garbage.

For additional savings, you can replace only the POA-LMP132 bulb and keep the original lamp cage. Watch our video guide and learn how.

RESETTING THE SANYO PLC-XR201/PLC-XR251 LAMP CONTROL MODE

Resetting the lamp control mode means your projector will be able to accurately track the number of hours left in your newly installed Sanyo POA-LMP132 (service parts no 610 345 2456) lamp.

• Turn the Sanyo PLC-XR201/PLC-XR251 projector on.
• Press the Menu option to display the On-Screen Menu.
• Press Point left/right button(s) to move a red frame poster to Setting Menu icon.
• Press the black arrow point button to move the red framed pointer to the Setting Menu Icon.
• Press Point Down button to move the red frame pointer to Lamp counter reset.
• Press the Select button.

• Another confirmation dialog box appears, select YES.
• The Lamp box will disappear and the Lamp Replace Dialog box appears.
• Select YES to reset Lamp Replace Counter.

• There are two modes for Lamp life control for the Sanyo PLC-XR201/PLC-XR251 . Mode 1 lets the lamp be turned on even after exceeding the recommended total hours of use. Mode 2 lets the lamp be turned on even after exceeding the recommended total hours BUT the projector turns off automatically after 3 minutes.
• The Sanyo PLC-XE33 projector has a Lamp control that allows you to change the brightness of the screen and extend the life of your lamp. High Mode: Brighter than the Normal mode. It will shorten the lamp life using this mode. Normal Mode: Normal brightness. Eco Mode: Lowers the brightness and reduces the lamp power consumption thereby extending the lamp life.

NOTE: When you reset the Lamp Replace Counter the Lamp Replace indicator stops lighting.

Prolong the life of your new Sanyo POA-LMP132 (service parts no 610 345 2456) lamp by regular cleaning the the air filter and allowing the Sanyo PLC-XR201/PLC-XR251 projector to stand for five minutes per turning the projector off.

The post Replacing POA-LMP132 in the Sanyo PLC-XR201/PLC-XR251 projector appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

This guide shows you how to replace the Sanyo PLC-XE33 projector lamp

When the Sanyo POA-LMP132 (service parts no 610 345 2456) nears the end of life, the Lamp life control menu will begin blinking yellow on your Sanyo PLC-XE33 projector.

The Lamp replacement icon will also appear on screen. If Mode 2 has been selected in the Lamp life control menu, the projection will turn off automatically after 3 minutes as soon as the Lamp Replacement icon appears.

Replace the Sanyo POA-LMP132 (service parts no 610 345 2456) immediately with a guaranteed authentic lamp. Be sure to verify that your lamp is authentic and buy from an authorized manufacturer.

For additional savings, you can replace only the POA-LMP132 bulb and keep the original lamp cage. Watch our video guide and learn how.

Buy authentic

If the price of the Sanyo POA-LMP132 (service parts no 610 345 2456) lamp you’re about to buy seems like an incredible bargain, chances are it’s counterfeit and has been created using inferior parts that  can damage the inside of your projector since it will not fit properly. Buying a knock-off lamp will also void your warranty and should anything happen to the projector you will not be covered.

The lifespan of your Sanyo POA-LMP132 (service parts no 610 345 2456)  lamp will vary depending on how much the projector is used and if the filters are cleaned regularly. To maintain the life of your lamp, wait at least five minutes before turning it off. Don’t operate the projector continuously without letting it stand for at least one hour every 24 hours.

STEP-BY-STEP INSTRUCTIONS

Before installation: Turn off the projector and unplug the AC cord. Allow the Sanyo PLC-XE33 projector to cool to the touch. This can take between 45 to 60 minutes. Don’t open the projector when hot since these machines operate under high temperatures and you can burn yourself.

Replacing the Sanyo POA-LMP132 (610 345 2456) Lamp Assembly

1. Remove the lamp cover for the Sanyo PLC-XE33 projector—it’s  located at the top of the projector towards the back. Locate the screw holding the lamp cover in place found on the side over top of the ventilation holes. Loosen the screw to remove the cover.

2. Inside you’ll find the Sanyo POA-LMP132 (service parts no 610 345 2456) lamp cage. Loosen all three screws holding the lamp cage in place. Grab the handles on the lamp cage and gently lift the lamp out of its socket. Place to one side. Be sure to dispose of the lamp properly through a local recycling program.

3. Take the new Sanyo POA-LMP132 (service parts no 610 345 2456) lamp cage by the handle—avoid touching the lamp surface as oil from your fingers can cause black spots to appear when the projector is turned on. Gently maneuver the lamp into place. Don’t force the lamp as this may damage it.

4. Once the lamp is in, tighten all three screws on the Sanyo POA-LMP132 (service parts no 610 345 2456) Lamp Assembly. Make sure the screws have been tightened properly or the Sanyo PLC-XE33 projector will not turn on.

5. Replace the Lamp Cover and tighten the screw.

6. Re-connect the power cord and turn on the Sanyo PLC-XE33 projector. If the Sanyo POA-LMP132 (service parts no 610 345 2456) lamp does not turn on after the warm-up period, try re-installing the lamp. Reset the lamp hour using the Lamp Control mode found on the Setting menu.

NOTE: Your old Sanyo POA-LMP132 (service parts no 610 345 2456) lamp should be properly recycled. These lamps contain mercury and can’t be placed into common garbage.

RESETTING THE SANYO PLC-XE33 LAMP TRACK

Resetting the lamp contol mode will let your projector accurately track the number of hours left in your Sanyo POA-LMP132 (service parts no 610 345 2456) projector lamp.

• Turn the Sanyo PLC-XE33 projector on.
• Press the Menu option to display the On-Screen Menu.
• Press Point left/right button(s) to move a red frame poster to Setting Menu icon.
• Press the black arrow point button to move the red framed pointer to the Setting Menu Icon.
• Press Point Down button to move the red frame pointer to Lamp counter reset.
• Press the Select button.

• Another confirmation dialog box appears, select YES.
• The Lamp box will disappear and the Lamp Replace Dialog box appears.
• Select YES to reset Lamp Replace Counter.

• There are two modes for Lamp life control. Mode 1 lets the lamp be turned on even after exceeding the recommended total hours of use. Mode 2 lets the lamp be turned on even after exceeding the recommended total hours BUT the projector turns off automatically after 3 minutes.
• The Sanyo PLC-XE33 projector has a Lamp control that allows you to change the brightness of the screen and extend the life of your lamp. High Mode: Brighter than the Normal mode. It will shorten the lamp life using this mode. Normal Mode: Normal brightness. Eco Mode: Lowers the brightness and reduces the lamp power consumption thereby extending the lamp life.

NOTE: When you reset the Lamp Replace Counter the Lamp Replace indicator stops lighting.

Prolong the life of your new Sanyo POA-LMP132 (service parts no 610 345 2456) lamp by regular cleaning the the air filter and allowing the Sanyo PLC-XE33 projector to stand for five minutes per turning the projector off.

The post Six easy steps for replacing the Sanyo PLC-XE33 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.