Sanyo POA-LMP36

You can expect between 1,000 to 3,000 hours of use from the Sanyo POA-LMP36 (service part no 610 293 8210). when installed properly. The life cycle of this projector lamp depends on how much the projector is used and whether the air filters have been cleaned regularly. (Clogged air filters cause the projector to heat up and this puts stress on the lamp.)

Avoid knock-offs since they use inferior materials that can damage your projector. If the price of your lamp seems too good to be true–WALK away. The few dollars you save are not worth it since these lamps don’t last as long as genuine lamps and can explode inside the projector.

Looking for a less expensive option? Are you technically adept?  Watch our step-by-step video on replacing only the Sanyo POA-LMP36 (610 293 8210) bulb instead of the entire lamp housing.

Projectors compatible with the Sanyo POA-LMP36 orprojector lamp:

• Sanyo PLC-SW20
• Sanyo PCL-XW20

Scroll down for links to step-by-step instructions on replacing the Sanyo POA-LMP36 (service part no 610 293 8210) lamps for each of these projectors.

When it’s time to replace the Sanyo POA-LMP36 (service part no 610 293 8210), your projector’s Lamp Replacement Indicator will turn yellow. Be sure to buy an genuine projector lamp. It’s worth paying the few extra dollars to be guaranteed a projector lamp that will work and will keep your warranty intact.

For step-by-step instructions on replacing your Sanyo POA-LMP36 (service part no 610 293 8210) lamp, click on your model listed below:

Sanyo PLC-SW20 projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP36 (service part no 610 293 8210) projector bulb for the Sanyo PLC-SW20 projector.

Sanyo PLC-XW20 projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP36 (service part no 610 293 8210) projector bulb for the Sanyo PCL-XW20 projector.

The post When to replace the Sanyo POA-LMP 36 appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Sanyo PLC-XW20 projector

One of the most important components in your Sanyo PLC-XW20 projector is the projector lamp. It’s primary role is to provide the right amount of light needed to transfer the images from the projector onto the screen. When the projector bulb goes, your Sanyo PLC-XW20 projector is not going to work.

Fortunately the projector bulb is one of the easiest components to replace. You’ll know when your projector lamp is nearing its end of life–the Lamp Indicator on the projector’s front control panel will start blinking yellow. That’s your clue to replace the projector lamp with a new Sanyo POA-LMP36 (service part no 610 293 8210).

Follow our hassle-free instructions below to get your projector back up an running in under 10 minutes. Be sure to read our instructions on finding the correct Sanyo POA-LMP36 (service part no 610 293 8210) for your Sanyo PLC-XW20 projector before replacing the existing projector bulb.

Go with original Sanyo POA-LMP36 lamps

You’ll notice right away there are hundreds of websites selling your replacement Sanyo POA-LMP36 (service part no 610 293 8210) projector lamp. It can be overwhelming trying to pick the right manufacturer. Let price be your first clue — cheaper priced projector lamps are usually generic knock-offs. While the lower price is tempting, keep in mind these lamps are usually made with cheaper parts that don’t have the original specifications for your Sanyo PLC-XW20 and these counterfeit lamps have not been calibrated to work with the high-tech mechanism in your projector.

Knock-off lamps often have a shorter life-span and can explode inside the projector causing significant damage to your projector when they overheat, break the ballast or explode inside. Learn more about how to protect yourself in our article: 7 Tips for spotting counterfeits.

Look for the company offering OEM genuine lamps with a hassle free warranty. These authentic Sanyo POA-LMP36 (service part no 610 293 8210) projector lamps will be slightly higher in price but are guaranteed to keep your projector working.

Looking for a less expensive option? Are you technically adept?  Watch our step-by-step video on replacing only the Sanyo POA-LMP36 (610 293 8210) bulb instead of the entire lamp housing.

Quick installation for the Sanyo POA-LMP36 projector lamp

Follow these six steps to a new Sanyo POA-LMP36 (610 293 8210) and a workingSanyo PLC-XW20 projector!

1. Turn the projector off. Disconnect the AC cord. Allow the Sanyo PLC-XW20 projector to cool down for at least 45 minutes. The inside of the projector gets extremely hot — don’t attempt to change the lamp with the projector running or you will burn yourself badly.

2. The lamp cover is on the bottom. Turn the projector over and remove the single screw holding the cover in place. Put the lamp cover to one side.

3. Remove the two screws holding the lamp assembly in place. Grab the handle and pull out the used Sanyo POA-LMP36 (610 293 8210) projector lamp. Be sure to send the lamp to your local recycling program.

4. Take the new Sanyo POA-LMP36 (6102938210) by the handle. Avoid touching the actual bulb since any fingerprints leave a black mark on the lamp when it heats up and give you black spots on your images. Using the handle, gently push the lamp into place.

5. Tighten the two screws on the Sanyo POA-LMP36 (service part no 610 293 8210) lamp assembly. Put the lamp cover back in place and tighten the single screw.

6. Re-connect the AC cord. Reset the Lamp Replace Counter following the step-by-step instructions below.

Resetting the Sanyo PLC-XW20 Lamp Replace Counter

NOTE: Reset the Lamp Replace Counter ONLY WHEN the Sanyo POA-LMP36 (service part no 610 293 8210) lamp has been REPLACED.

• Press the MENU Button to display the MAIN MENU.
• Press the POINT LEFT/RIGHT button and scroll right to select SETTING.
• Press the SELECT button to display the SETTING DISPLAY menu.
• Press the POINT DOWN button (a red arrow will appear).
• Move the red arrow to the LAMP AGE and then press the SELECT button.
• The message “Lamp replace counter reset?”  appears. Move the arrow down to YES and press the SELECT button.
• The message “OK?” appears. Click on YES.
• Move the arrow to QUIT and press the SELECT button.

In order for the projector to properly track the life cycle of your Sanyo POA-LMP36 (service part no 610 293 8210) projector lamp you’ll need to reset the Lamp Replace Counter. Once reset it will properly track the correct age of your newly installed Sanyo POA-LMP36 (service part no 610 293 8210) projector bulb and trigger the Lamp Indicator on your Sanyo PLC-SW20 projector.

Prolong the life of your Sanyo POA-LMP36 lamp

Follow these easy tips to make your Sanyo POA-LMP36 (service part no 610 293 8210) last longer!

• Wait at least five minutes before turning the Sanyo PLC-XW20 projector off.
• Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
• Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP36 (service part no 610 293 8210) and prevent the Sanyo PLC-XW20 projector from overheating.

The post Installing a new projector lamp for Sanyo PLC-XW20 appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Sanyo PLC-SW20 projector

Follow our easy 10-minute guide to installation.  It will take less than 10 minutes!

The lamp in your projector is one of the most important pieces of equipment. Projector lamps, also known as projector light bulbs or projector bulbs, come in different wattage and are created to match the specifications in your projector.

When the projector lamp in your Sanyo PLC-SW20 projector is nearing it’s end of life, you’ll see a yellow blinking light on the top of the control panel. This is the Lamp Indicator warning you that it’s time to replace the projector bulb. Follow our easy 3-step guide to replacing your projector bulb.

STEP ONE: Buy the right projector lamp

Your replacement projector lamp is Sanyo POA-LMP36 (service part no 610 293 8210). One of the best things you can do to prolong the life of your projector and get the optimum use out of your Sanyo PLC-SW20 is to invest in an genuine lamp from the original manufacturer. Unlike generic lamps, these original projector bulbs use authentic parts that work properly in your projector. Knock-off lamps may sell at a slightly cheaper price but they have not been made with original materials and the toxic products they use are inferior. They can actually damage your projector. (Your warranty also becomes invalid.)

There are plenty of  knock-off Sanyo POA-LMP36 lamps on the market posing as the real thing. Your biggest clue will be the price. What may seem like a bargain though may actually end up costing you more money. Protect yourself, spot the knock-off before buying and go with the guaranteed genuine Sanyo POA-LMP36 (610 293 8210) projector lamp for your Sanyo PLC-SW20 projector.

Looking for a less expensive option? Are you technically adept?  Watch our step-by-step video on replacing only the Sanyo POA-LMP36 (610 293 8210) bulb instead of the entire lamp housing.

STEP TWO: Installing the Sanyo POA-LMP36 lamp

Important Safety Steps:

• Turn the projector off. Disconnect the AC cord. Allow the Sanyo PLC-SW20 projector to cool down for at least 45 minutes. The inside of the projector gets extremely hot — don’t attempt to change the lamp with the projector running or you will burn yourself badly.

• The lamp cover is on the bottom. Turn the projector over and remove the single screw holding the cover in place. Put the lamp cover to one side.
• Remove the two screws holding the lamp assembly in place. Grab the handle and pull out the used Sanyo POA-LMP36 (6102938210) projector lamp. Be sure to send the lamp to your local recycling program. 
• Take the new Sanyo POA-LMP36 (service part no 610 293 8210) by the handle. Avoid touching the actual bulb since any fingerprints leave a black mark on the lamp when it heats up and give you black spots on your images. Using the handle, gently push the lamp into place.
• Tighten the two screws on the lamp assembly.
• Put the lamp cover back in place and tighten the single screw.
• Re-connect the AC cord.
• Move onto Step three to reset the Lamp Replace Counter.

DON’T throw this used Sanyo POA-LMP36 (service part no 610 293 8210) lamp into the garbage since it contains mercury and needs to be properly recycled.

STEP THREE: Resetting the Sanyo PLC-SW20 Lamp Replace Counter

NOTE: Reset the Lamp Replace Counter ONLY WHEN the Sanyo POA-LMP36 (service part no 610 293 8210) lamp has been REPLACED.

• Press the MENU Button to display the MAIN MENU.
• Press the POINT LEFT/RIGHT button and scroll right to select SETTING.
• Press the SELECT button to display the SETTING DISPLAY menu.
• Press the POINT DOWN button (a red arrow will appear).
• Move the red arrow to the LAMP AGE and then press the SELECT button.
• The message “Lamp replace counter reset?”  appears. Move the arrow down to YES and press the SELECT button.
• The message “OK?” appears. Click on YES.
• Move the arrow to QUIT and press the SELECT button.

In order for the projector to properly track the life cycle of your Sanyo POA-LMP36 (service part no 610 293 8210) projector lamp you’ll need to reset the Lamp Replace Counter. Once reset it will properly track the correct age of your newly installed Sanyo POA-LMP36 (service part no 610 293 8210)projector bulb and trigger the Lamp Indicator on your Sanyo PLC-SW20 projector.

Want to prolong the life of your Sanyo POA-LMP36 projector bulb?

Follow these easy tips to make your Sanyo POA-LMP36 (service part no 610 293 8210) last longer!

• Wait at least five minutes before turning the Sanyo PLC-SW20 projector off.
• Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
• Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP36 (service part no 610 293 8210) and prevent the Sanyo PLC-SW20 projector from overheating.

The post 3 Easy steps to replacing the Sanyo PLC-SW20 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.