Be sure to use the same type of projector lamp bought from a verified source that has been manufactured to meet the specifications. See below for the correct POA-LLB02 / POA-LMP39 (service part no 610 292 4848) lamp to use with your particular model and links for step-by-step instructions for replacing the lamps in all Sanyo PLC-EF30/PLC-EF31/PLC-XF30/PLC-XF31 projectors.

Resist the temptation to buy a cheaper counterfeit model  as this can damage the sensitive mechanisms in your Sanyo PLC-EF30/PLC-EF31/PLC-XF30/PLC-XF31 projectors. Check your model to see if you’ll need two replacement lamps for your projector.

Sanyo Lamp Replace Indicator

As the lamp reaches its end of life, the Lamp Replace indicator lights turns yellow indicating it’s time for a new POA-LLB02 / POA-LMP39 (610-292-4848) as the current lamp is nearing end of life. If the POA-LLB02 / POA-LMP39 (service part no 610 292 4848)9 light does  burn out, then the indicator light will be flashing. If your projector has more than one lamps, check the number of the lamp shown on screen as Lamp Status Display on the Sanyo PLC-EF30/PLC-EF31/PLC-XF30/PLC-XF31 projectors so you can determine which lamp needs to be replaced.

On Screen Indicators

The Lamp Status Display appears on screen showing the status of each lamp. This will be the same menu for  all Sanyo PLC-EF30/PLC-EF31/PLC-XF30/PLC-XF31 projectors.

Yellow Lamp: Lamp lights normally and is ON

Dim Lamp: Projection Lamp is turned off.

Red Lamp: Projections Lamp is nearing its end. When image becomes darker replace lamp. The LAMP REPLACE indicator will be flashing yellow.

X mark on Lamp: Projection lamp is defective or fails to be turned on. Restart the projector and if the X still appears, replace the lamp marked with the X.

Sanyo Lamp Mode Changeover

When a lamp is no longer working, the Lamp Management Function (Lamp Mode) automatically changes the combination of lighting from either two lamps to one lamp being used.

The Sanyo PLC-EF30/PLC-EF31/PLC-XF30/PLC-XF31 projectors series gives you the option of extending your lamp life by manually changing the Lamp Mode to use only one lamp. To do this:

1. Press Menu button to get to the On-Screen Menu.
2. Press Point left/right buttons to select Setting and press Select button. Setting dialog box appears.
3. Press Point Down button to move a red frame pointer to Lamp Mode.
4. Set the 2 Lamp Mode to 1 Lamp Mode lamp mode by pressing Point left/right buttons.
5. When you switch the Lamp Mode from using 2 lamps to using 1 lamp the image becomes a little darker.
6. When you switch the Lamp Modefrom using 1 lamp to using 2 lamps, the image becomes a little brighter gradually.

You must wait for 90 seconds after changing Lamp Mode before you can access this option again.

Click on your Sanyo Projector for step-by-step instructions on how to replace your lamp.

Lamp series: POA-LLB02/POA-LLB02 / POA-LMP39 (610 292 4848)

Sanyo PLC-EF30

Click here for step-by-step instructions on how to change the  PLC-EF30 lamp.

Sanyo PLC-EF31/ PLC-EF31NL / PLC-EF31N/ PLC-EF32

Click here for step-by-step instructions on how to change the PLC-EF31/EF32 series lamp

Sanyo PLC-XF31

Click here for step-by-step instructions on how to change the PLC XF31 series lamp.

Sanyo PLC-XF30/ XF30NL

Click here for step-by-step instructions on how to change PLC-XF30 series lamp.

The green alternative

If you are looking an option that is more eco-friendly and can save you some money, consider replacing only the lamp and re-using the original lamp cage. Watch our step-by-step tutorial to show you what is needed.

The post When to change your Sanyo POA-LLB02 and POA-LMP39 lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Be sure to use the same type of Sanyo projector lamp bought from a verified source that has been manufactured to meet the specifications. Use model POA-LLB02 / POA-LMP39 (service part no 610 292 4848)  as your Sanyo projector lamp replacement. Resist the temptation to buy a cheaper POA-LLBO2 or POA-LMP38 counterfeit model as this can damage the sensitive mechanisms in your Sanyo PLCEF30 projector.

STEP-BY-STEP INSTRUCTIONS FOR SANYO PLC-EF30 Lamp Replacement

Before installation

1. Check the number of Sanyo POA-LLB02 / POA-LMP39 (service part no 610 292 4848) lamps needing to replaced on the Lamp Status Display. You may need to replace both lamps.
2. Turn off the projector and unplug the AC cord.
3. Allow the Sanyo PLC-EF30 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures.

Replacing the POA-LMP39 (610-292-4848) Lamp Assembly

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

1. At the back of the Sanyo PLC-EF30 projector you’ll find the Lamp Hazard cover. Using a Philips screwdriver loosen the three screws that hold the cover in place. Put the cover to one side.
2. Remove the two screws on either side of each the Sanyo POA-LLB02 / POA-LMP39 (service part no 610 292 4848) lamp. Grab the handle on the lamp cage and gently pull out each lamp. Place those lamps to one side.
3. Take the new Sanyo POALLB02 / POA-LMP30 (6102924848) lamp cage by the handle and gently maneuver it into place.
4. Avoid touching the glass or the bulb. It should slide it easily – don’t force the lamp.
5. Tighten the screws on the Sanyo POA-LLB02 / POA-LMP39 (service part no 610 292 4848) Lamp Assembly
6. Replace and tighten the three screws on either side of Lamp Hazard Cover.
7. Re-connect the power cord and turn on the Sanyo PLC-EF30 projector.

Reset the Sanyo PLC-EF30 Lamp Replacement Counter

Reset the Lamp Replacement Counter only when the Sanyo POA-LLB02 / POA-LMP39 (service part no 610 292 4848) lamp has been replaced.

Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

• Turn the Sanyo PLC-EF30 projector on.
• Press the Menu option so the On-Screen Menu will appear.
• Press Point left/right button(s) to move a red frame poster to Setting Menu icon.
• Press Point Down button to move the red frame pointer to Lamp counter reset and then press the Select button.
• Move arrow to replace lamp number (Lamp 1 or Lamp 2) and then press Select button. The message “Lamp replace counter Reset?” will be displayed.
• Move the pointer to YES and then press Select button. Be sure to reset the correct lamp number otherwise Lamp Replace indicator continues lighting.

• The Lamp box will disappear and the Lamp Replace Dialog box appears.
• Select YES to reset Lamp Replace Counter.
• Do not reset Lamp Replace Counter except after the Projection Lamp has been replaced. NOTE: When  the Lamp Replace Counter is reset, the Lamp Replace indicator stops lighting.

Prolong the life of your newly installed Sanyo POA-LLB02 / POA-LMP39 (service part no 610 292 4848) by waiting at least five minutes before turning the Sanyo PLC-SU32 projector off and turning the projector off for at least one hour turned off every 24 hours. Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LLB02 / POA-LMP39 (service part no 610 292 4848).

Save money, save resources

If you are looking an option that is more eco-friendly and can save you some money, consider replacing only the lamp and re-using the original lamp cage. Watch our step-by-step tutorial to learn more.

The post Changing the Sanyo PLC-EF30 lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.