Sanyo POA-LMP48 (service part no 610 301 7167)

The life expectancy of your Sanyo POA-LMP48 (service part no 610 301 7167) lamp depends on the amount of usage and whether the air filters are cleaned on a regular basis. A build up of dust on the filters will reduce the cooling fans effectiveness and may cause the lamp to overheat.

The life of the Sanyo POA-LMP48 (service part no 610 301 7167) lamp runs anywhere from 1,000 to 3,000 hours. It’s always a good idea to keep a spare lamp on hand so you can replace the lamp immediately and not wait to use the projector.

The best type of lamp to buy is one that has been guaranteed authentic and created by approved manufacturers who use the correct parts for the lamp. Knock-off lamps use counterfeit parts that can explode inside the projector or not fit properly thereby damaging the sensitive mechanism in the projector. The initial low cost of these counterfeit lamps may end up costing you more money in the long run if your projector is ruined. Buy an authentic Sanyo POA-LMP48 (service part no 6103017167) will maintain your warranty while providing you with a manufacturer’s guarantee.

Looking for a less expensive option? Are you technically adept?  Watch our step-by-step video on replacing only the Sanyo POA-LMP48 (service part no 610 301 7167) bulb instead of the entire lamp housing.

The Sanyo POA-LMP48 (service part no 610 301 7167) can be used in the following projectors:

• Sanyo PLC-XT10
• Sanyo PLC-XT15

For step-by-step instructions on how to replace the Sanyo POA-LMP48 (610 301 7167)4 projector lamp, please click on your specific model listed below:

Click here for step-by-step instructions on how to change the Sanyo POA-LMP48 (service part no 610 301 7167) projector lamp for the Sanyo PLC-XT10 projector.

Click here for step-by-step instructions on how to change the Sanyo POA-LMP48 (service part no 610 301 7167) projector lamp for the Sanyo PLC-XT15 projector.

Prolong the life of your new Sanyo POA-LMP48 (6103017167) lamp

To maintain the life of your newly installed Sanyo POA-LMP48 (service part no 610-301-7167), follow these three suggestions:

• Wait at least five minutes before turning the Sanyo PLC-XT10 projector off.
• Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
• Clean the air filters regularly so the projector won’t overheat putting undue stress on on the Sanyo POA-LMP48 (service part no 610-301-7167) lamp.
  

The post When to replace the POA-LMP48 (610 301 7167) projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

STEP-BY-STEP INSTRUCTIONS FOR SANYO PLC-XT10 LAMP REPLACEMENT

When it’s time to change your lamp on your Sanyo PLC-XT10 projector, you’ll notice the yellow light blinking on the Lamp Replacement Indicator.

Be sure to buy an authentic Sanyo POA-LMP48 (service part no 610 301 7167)  for your replacement lamp bought from a verified source. Buying an authentic replacement lamp will ensure that you’re installing a lamp manufactured with work properly and not damage your projector. Resist the temptation to buy a cheaper  counterfeit model as this can damage the sensitive mechanisms in your Sanyo PLC-XT10 projector.

Looking for a less expensive option? Are you technically adept?  Watch our step-by-step video on replacing only the Sanyo POA-LMP48 (service part no 610 301 7167) bulb instead of the entire lamp housing

Before Installing the Sanyo POA-LMP48 Projector Lamp

1. Turn off the projector and unplug the AC cord.
2. Allow the Sanyo PLC-XT10 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures. Without letting the projector cool properly there is  burn danger.

Replacing the Sanyo POA-LMP48 (6103017167) Lamp Assembly

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

• At the back of the Sanyo PLC-XT10 projector you’ll find the Lamp Cover. Using a Philips screwdriver loosen the screw holding the cover in place. Put the cover to one side.
• Remove the two screws on either side of each of the Sanyo POA-LMP48 (service part no 610-301-7167)  lamp. Grab the handle on the lamp cage and gently pull the lamp out. Place the used lamp to one side. Be sure to dispose of the used lamp through a local recycling program. Don’t throw this lamp into the regular garbage as it contains mercury.

• Take the new Sanyo POA-LMP48 (service part no 6103017167) lamp cage by the handle and gently manuever it into place.
• Avoid touching the glass or the bulb. It should slide it easily – don’t force it. Tighten the two screws on the Lamp Assembly. Make sure they are tightened properly otherwise the projector will not turn back on.
• Replace the Lamp Cover and tighten the screw. Let the projector stand for five minutes so the lamp can stabilize. Re-connect the power cord and turn the  Sanyo PLC-XT10 projector on. If the projector doesn’t turn, check that all the screws have been tightened. Try repeating the installation steps.

NOTE: Your old  Sanyo POA-LMP48 (service part no 610-301-7167) lamp should be properly recycled. These lamps contain mercury and can’t be placed into common garbage.

Reset the Sanyo PLC-XT10 Lamp Replacement Counter

Reset the Lamp Replacement Counter only when the Sanyo POA-LMP48 (service part no 610-301-7167) lamp has been replaced.

Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

• Turn the Sanyo PLC-XT10 projector on.
• Press the Menu option so the On-Screen Menu will appear.
• Press Point left/right button(s) to move a red frame poster to Setting Menu icon.
• Press Point Down button to move the red frame pointer to Lamp counter reset.
• Press the Select button. The message “Lamp replace counter Reset?” will be displayed.
• Move the pointer to YES and then press Select button. 

Prolong the life of your new Sanyo POA-LMP48 (6103017167) lamp

To maintain the life of your newly installed Sanyo POA-LMP48 (service part no 610-301-7167), follow these three suggestions:

• Wait at least five minutes before turning the Sanyo PLC-XT10 projector off.
• Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
• Clean the air filters regularly so the projector won’t overheat putting undue stress on on the Sanyo POA-LMP48 (service part no 610-301-7167) lamp.
  

The post How to install your new Sanyo PLC-XT10 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Sanyo PLC-XT15 projector

Replace your Sanyo PLC-XT15 projector lamp in 3 easy steps.

If the picture on your Sanyo PLC-XT15  projector is dim or looks unnatural the Sanyo POA-LMP48 (service part no 610 301 7167) is reaching its end of life. You may also notice the Replace Lamp Indicator light on the front panel is yellow. Replace the Sanyo POA-LMP48  in the Sanyo PLC-XT15 projector easily following the step-by-step below.

The lifespan of your Sanyo POA-LMP48 (service part no 610 301 7167)  lamp will vary depending on how much the projector is used and if the filters are cleaned regularly.

Looking for a less expensive option? Are you technically adept?  Watch our step-by-step video on replacing only the Sanyo POA-LMP48 (service part no 610 301 7167) bulb instead of the entire lamp housing

STEP ONE: Purchasing the correct projector lamp

The best thing you can do to prolong the life of your Sanyo PLC-XT15  and save money is to invest in an original Sanyo POA-LMP48 (service part no 6103017167) projector lamp. Generic lamps look like a great bargain since they are generally cheaper, however, these knock-off lamps are created with inferior materials. They are susceptible to explosions, have a shorter life span and can damage the precise components in your Sanyo PLC-XT15 projector.   Installing a knock-off generic lamp also voids your warranty. Learn more about spotting dangerous projector lamps by reading our article: 7 tips for spotting counterfeits.

Looking for a less expensive option? Are you technically adept?  Watch our step-by-step video on replacing only the Sanyo POA-LMP48 (service part no 610 301 7167) bulb instead of the entire lamp housing.

STEP TWO: Installing the new Sanyo POA-LMP48 (6103017167) lamp

• Allow the Sanyo PLC-XT15 projector to thoroughly cool before changing the lamp. Turn off the projector, unplug the AC cord and allow 45 to 60 minutes for the projector to cool. These projectors operate under high heat and there is a possibility of being burned, if the projector is not fully cooled before changing the Sanyo POA-LMP48 (service part no 610 301 7167) lamp.
• The lamp cover for the Sanyo PLC-XT15 is at the bottom of the projector. Gently turn projector over and loosen the screw holding the cover in place. Place the cover to one side.
• Inside you’ll find the Sanyo POA-LMP48 (service part no 610-301-7167) lamp cage. Loosen both screws holding the lamp cage in place. Grab the lamp handle and gently lift the lamp out of its socket. Place to one side. Be sure to dispose of the used lamp through a local recycling program. Don’t throw this lamp into the regular garbage as it contains mercury.

• Taking the new Sanyo POA-LMP48 lamp assembly by the handle place it into the slot. Avoid touching the actual bulb as the oil from your fingers can burn a black spot on the lenses or you can accidentally break the bulb. Don’t force the lamp into place — it should slide into the slot easily.
• Once the lamp is in, tighten both screws on the Sanyo POA-LMP48 (service part no 6103017167) lamp assembly. Make sure the screws have been tightened properly or the Sanyo PLC-XT15 projector will not turn on.
• Replace the Lamp Cover and tighten the screw. Re-connect the power cord and turn on the Sanyo PLC-XT15 projector If the Sanyo POA-LMP48 lamp does not turn on after the warm-up period, try re-installing the lamp.
• Reset the Lamp Replacement Counter by following the instructions below.

NOTE: Your old  Sanyo POA-LMP48 (service part no 610-301-7167) lamp should be properly recycled. These lamps contain mercury and can’t be placed into common garbage.

STEP THREE: Reset the Sanyo PLC-XT15 Lamp Replace Counter

The Lamp Replacement Counter for the Sanyo PLC-XT15 will track the correct age of your newly installed lamp and trigger the Lamp Replace Indicator. Failure to reset the counter may result in the projector not tracking the end of life for the  Sanyo POA-LMP48 (service part no 6103017167) and letting the projector inadvertently use the lamp past its normal life cycle. Your Sanyo PLC-XT15 may stop working suddenly if the Lamp Replace Counter has not been properly set.

• Press the MENU Button to display the MAIN MENU. Press the POINT LEFT/RIGHT button and scroll right to select SETTING.
• Press the SELECT button to display the SETTING DISPLAY menu.
• Press the POINT DOWN button (a red arrow will appear).
• Move the red arrow to the LAMP AGE and then press the SELECT button.
• The message “Lamp replace counter reset?”  appears. Move the arrow down to YES and press the SELECT button.
• Move the arrow to QUIT and press the SELECT button.

Extend the life of the Sanyo POA-LMP48 projector lamp

Extend the life of your newly installed  Sanyo POA-LMP48 (service part no 610 301 7167) by following these helpful tips:

• Wait at least five minutes before turning the Sanyo PLC-XT15 off.
• Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
• Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP48 (service part no 6103017167) and prevent the Sanyo PLC-XT15 projector from overheating.

The post 3 Easy steps to replace the Sanyo PLC-XT15 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.