3 steps to a new Epson PowerLite 760c projector lamp

PowerLite-760c_projector_ELPLP32_projector_lampFollow this 3-step replacement guide to install as new Epson PowerLite 760c projector lamp.

Step 1: Be prepared, buy the right lamp

There is no shortage of the Epson PowerLite 760c projector lamp to buy since the Internet has been flooded with sellers. Before you buy a generic projector lamp there are some important things to consider:

Save yourself unnecessary headaches and keep your  warranty intact for your Epson PowerLite 760c projector. Look for the seal of approval and buy authentic Epson ELPLP32 from a recognized dealer. You’ll be getting a far superior product. Read more about the 7 Ways to Spot a Counterfeit Lamp.

Find this lamp on Amazon sold by these authorized dealers:

Step 2: Know the end-of life signs

Epson_PowerLite 760c_Epson_ELPLP31_projector_lampWatch for these signs indicating  end of life for the Epson ELPLP32 projector lamp:

  • The lamp warning light on the projector starts flashing orange. If it turns red and stays red, replace the Epson ELPLP32 projector lamp immediately.
  • Imaged becomes dark, colours are off or appear to be deteriorating
  • A message saying “Replace the lamp” appears on screen.

Wondering how many hours are left? Track the number of hours left in the Epson ELPLP32 projector lamp on MAIN/INFO menu. If the Brightness setting is on normal, the ELPLP32 projector lamp will last up to 2000 hours. Change the Brightness setting to low and the Epson ELPLP32 lamp will last up to 3000 hours.

Step 3: Installing the new Epson ELPLP32

Installation will take under 10 minutes but before installing the new Epson ELPLP32 projector lamp into the Epson PowerLite 760c projector, be sure to follow these preparation steps:

Epson_PowerLite 760c_Epson_ELPLP31_projector_lamp_unplug_power_cord

  • Turn power button off and wait for the power light to stop flashing.
  • Unplug the power cord from the Epson Powerlite 760c projector.
  • The Epson Powerlite 760c should be cool to the touch before you try to change the Epson ELPLP32 lamp. This projector operate at a high temperatures and there is a risk of burning if you don’t wait for the cool down period.
  • Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Epson_PowerLite 760c_Epson_ELPLP31_projector_lamp_remove_cover

  • Turn the Epson PowerLite 760c over and placing on a soft, scratch free surface.
  • Press on the tabs located on top of the Epson PowerLite 760c cover. Lift up the lamp cover.

Epson_PowerLite 760c_Epson_ELPLP31_projector_lamp_loosen screws

  • Using the screw driver provided with the Epson PowerLite 760c projector, loosen the two screws holding the Epson ELPLP32 lamp in place.

 

Epson_PowerLite 760c_Epson_ELPLP31_projector_lamp_removalPressing on the indents on the sides of the Epson ELPLP32, pull the projector lamp gently up out of the Epson PowerLite 760c projector. Take care not to bang the actual lamp or it may break. Learn how to do a proper clean up if the lamp breaks or explodes.

NOTE: The Epson ELPLP32 projector lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps and be good to the environment.
Epson_PowerLite 760c_Epson_ELPLP31_projector_lamp_replace_air_filter

  • Gently place the new Epson ELPLP32 lamp into the Epson PowerLite 760c making sure not to touch the actual bulb. The oil on your fingers will leave a burn mark on the lamp once it heats up and this can cause black out spots on the screen.
  • Tighten the screws on the new Epson ELPLP32 lamp.
  • Slide the air filter out and remove it immediately. Slide in the new filter that came with the Epson ELPLP32 lamp. Replace the lamp cover.
  • You are now ready to reset the lamp timer.

 

Reset the lamp timer in the Epson PowerLite 760c

Your Epson PowerLite 760c has a built-in timer to track the life of the Epson ELPLP32 projector lamp. So, it’s very important that you reset the lamp timer every time you replace the Epson ELPLP32 projector lamp. Here’s how:

Epson_PowerLite 760c_Epson_ELPLP31_projector_lamp_reset_lamp_timer

 

  • Press the MENU button on either the remote control on the projector’s control panel.
  • Scroll down to the RESET option.
  • Press Enter. The RESET ALL screen will appear.
  • Scroll down to LAMP-HOURS RESET.
  • Press ENTER to open up the confirmation screen

 

Epson_PowerLite 760c_Epson_ELPLP31_projector_lamp_reset_lamp_confirmation_screen

 

  • Highlight YES.
  • Press ENTER.
  • Press ESC or MENU to exit this option.

 

Congratulations! You’ve just installed at new Epson ELPLP32 projector lamp in your Epson PowerLite 760c. Here are some tips to extend the life of your Epson ELPLP321 lamp:

  • Keep your air filters clean to avoid overheating the projector.
  • Turn off the Epson Powerlite 760c projector projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
  • Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
  • Learn more with Top tips for extending DLP projector lamp life

 

Tagged with: ,

Leave a Reply

Your email address will not be published. Required fields are marked *

*

Time limit is exhausted. Please reload CAPTCHA.

This site uses Akismet to reduce spam. Learn how your comment data is processed.