We're now Screen and Projector! For updated content, visit ScreenAndProjector.com and follow @screenandproj on social media!
Home › About Us › Page 119

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓
ASK DP-6150 projector, ASK Proxima LAMP-026

ASK DP-6150 projector

Follow our quick and easy step guide to installing a new ASK Proxima LAMP-026 projector lamp for your ASK DP-6150 projector.

Step 1: Finding the correct lamp

ASK DP-6150 lamp warning message, ASK LAMP-026

Lamp warning screen

ASK DP-6100 lamp replacement alarm, ASK LAMP-026

Lamp alarm

 

 

 

 

Watch for the warning messages on the ASK DP-6150 projector screen as well as the ALARM on the projector light red. Either of these messages are indicators that the ASK LAMP-026 for your ASK DP-6150 projector must be replaced immediately.

Go with a genuine ASK LAMP-026 lamp

Be safe and get the best lamp for your ASK DP-6150 projector. Buy an authentic lamp from an authorized dealer that guarantees the ASK Proxima LAMP-026 you are installing will work in harmony with your projector. These genuine ASK Proxima LAMP-026 lamps have been manufactured with the correct materials and are designed to work properly with the intricate components in your ASK DP-6150 projector.

While the cheaper knock-off lamps sold at discount prices appear to be a smart bargain, they actually pose a danger to your health. Copy-cat manufacturers create these lamps are using toxic materials such as the cancer-causing compound Krypton 85 to get the same results since they don’t have access to the proper compounds. When these generic “compatible” lamps break or explode from overheating, anyone near the projector is exposed people to these toxic materials inside the lamp. Many generic lamps are also created without the proper safety device to protect your eyesight from UV light.Installing them also voids your projector warranty.

Protect your health and keep your projector warranty valid — buy an authentic ASK Proxima LAMP-026.

STEP 2: Replacing the ASK LAMP-026 projector lamp

IMPORTANT: Allow the ASK DP-6150 projector to fully cool down for at least one hour before replacing the ASK LAMP-026. These projectors operate under high heat and there is a seriousrisk of burning if the projector is not cooled enough.

ASK DP-6150 lamp cover, ASK LAMP-026To install a new ASK Proxima LAMP-026 lamp:

  • Gently turn over the ASK DP-6150 projector to access the lamp cage.
  • Loosen the 3 screws holding the ASK Proxima LAMP-026 lamp in place.
  • Grab the handle on the ASK Proxima LAMP-026 lamp cage and gently lift out the lamp. Place to one side.
  • IMPORTANT: These lamps contain mercury and must go to a local recycling program for proper disposal. Don’t throw used ASK LAMP-026 lamps into regular garbage! ASK DP-6150 lamp replacement, ASK LAMP-026
  • Take the new ASK Proxima LAMP-026 lamp. Don’t touch the bare bulb since the oil on your finger will burn a black mark on the lamp when the projector is turn on.
  • Place the ASK Proxima LAMP-026 into the projector.
  • Tighten the three screws on the new ASK Proxima LAMP-026 lamp.
  • Be sure to clean the filter.
  • You are ready to reset the Lamptimer.

 

STEP 3: Resetting the Lamptimer

It’s important to reset the Lamptimer after replacing the ASK Proxima LAMP-026 in the ASK DP-6150 projector in order that the lamp life be accurately tracked and recorded. Failure to do so may result in the lamp being used longer than it’s lamp life.

ASK DP-6150 lamp reset menu, ASK LAMP-026ASK DP-6150 replace lamp icon, ASK LAMP-026

 

To reset the Lamptimer:

  • Open the MAIN MENU. Press ENTER.
  • Scroll down to the SERVICE menu. Press ENTER.
  • Scroll down to the Reset lamptimer option. Press ENTER.
  • The lamptimer icon will appear to show you have reset the timer.
Tagged with: , , , , , , , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓
ASK DP-6100, ASK LAMP-026

ASK DP-6100 projector

Follow our 3 step guide to a new ASK Proxima LAMP-026 projector lamp for your ASK DP-6100 projector.

Step 1: Finding the correct lamp

 

ASK DP-6100 lamp replacement alarm, ASK LAMP-026

Lamp alarm

ASK DP-6100 lamp warning message, ASK LAMP-026

Lamp warning screen

 

 

 

 

 

When it’s time to replace the ASK Proxima LAMP-026 for your ASK DP-6100 projector, you’ll see the ALARM button on the projector light up red. A lamp warning message will also appear on screen.

Go with authentic

You’ll get the best lamp for your ASK DP-6100 projector when you buy from an authorized dealer. An ASK Proxima LAMP-026 manufactured by an OEM company use the correct materials and are designed to work properly with the intricate components in your ASK DP-6100 projector.

Beware of cheaper knock-off lamps sold at discount prices. They appear to be a great bargain but will actually cost more money in the long run. These lamps have a shorter life span and will damage your projector. The copy-cat manufacturers creating these lamps don’t have the same safety concerns are and using toxic materials such as the cancer-causing compound Krypton 85 to manufacture their inferior lamps.  These generic “compatible” lamps are prone to breaking or exploding from overheating, exposing people to these toxic materials inside the lamp. Installing them also voids your projector warranty.

Protect your health and keep your projector warranty valid — buy an authentic ASK Proxima LAMP-026 .

 STEP 2: Replacing the ASK LAMP-026 projector lamp

IMPORTANT: Before replacing the ASK Proxima LAMP-026 allow the ASK DP-6100 projector to fully cool down for at least one hour. These projectors operate under high heat and there is a seriousrisk of burning if the projector is not cooled enough.

ASK DP-6100 lamp cover, ASK LAMP-026To install a new ASK LAMP-026 lamp:

  • Gently turn over the ASK DP-6100 projector to access the lamp cage.
  • Loosen the 3 screws holding the ASK Proxima LAMP-026 lamp in place.
  • Grab the handle on the ASK LAMP-026 lamp cage and gently lift out the lamp. Place to one side.
  • IMPORTANT: These lamps contain mercury and should be sent to a local recycling program for proper disposal. Don’t throw into regular garbage!

 

ASK DP-6100 lamp replacement, ASK LAMP-026

  • Take the new ASK Proxima LAMP-026 lamp. Don’t touch the bare bulb since the oil on your finger will burn a black mark on the lamp when the projector is turn on. This will cause a black spot on the screen and affect the projected image.
  • Place the ASK LAMP-026 into the projector.
  • Tighten the three screws on the new ASK Proxima LAMP-026 lamp.
  • Be sure to clean the filter.
  • You are ready to reset the Lamptimer.

 

STEP 3: Resetting the Lamptimer

It’s important to reset the Lamptimer after replacing the ASK LAMP-026 in the DP-6100 projector in order that the lamp life be accurately tracked and recorded. Failure to do so may result in the lamp being used longer than it’s lamp life.

ASK DP-6100 lamp reset menu, ASK LAMP-026ASK C100/C90 lamp reset icon, ASK LAMP-026

 

To reset the Lamptimer:

  • Open the MAIN MENU. Press ENTER.
  • Scroll down to the SERVICE menu. Press ENTER.
  • Scroll down to the Reset lamptimer option. Press ENTER.
  • The lamptimer icon will appear to show you have reset the timer.
Tagged with: , , , , , , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓
ASK C60 XGA, projector, ASK-026 lamp

ASK C60 XGA, projector,

ASK C60 XGA, projector alarm, ASK 26 lamp

Projector Alarm

When it’s time to replace the ASK Proxima LAMP-026 for your ASK C60 XGA projector, you’ll see the ALARM button on the projector light  red.  A warning message will also appear on screen.

Replace the ASK Proxima LAMP-026 in the ASK C60 XGA projector in 3 easy steps by following our step-by-step guide.

STEP 1: Buying the correct lamp

It’s important to purchase your ASK Proxima LAMP-026from an authorized dealer and get the best lamp for your ASK C20 SVGA projector.  There are plenty of “bargain” generic lamps being sold that claim to be the same as an authentic ASK LAMP-026 lamp.

Beware of these cheaper knock-off lamps as they often turn out to be more expensive in the long run. Not only do they have a much shorter life, they produce a poor quality picture and since they are not fitted properly usually damage the sensitive mechanisms in your ASK C60 XGA projector.

ASK LAMP-026Even more disturbing: Copy-cat manufacturers are using carcinogenic Krypton 85 to get the same performance as authentic lamps. Since these poor quality lamps are prone to explosions and breakage, consumers are being exposed to this toxic substance. Learn how to protect yourself against dangerous counterfeit lamps. Keep yourself and your projector safe by installing an authentic ASK Proxima LAMP-026 from a recognized reseller.

STEP 2: Install the ASK LAMP-026

There is a risk of burning yourself if you try to replace the ASK LAMP-026 before the ASK C60 XGA projector has cooled down sufficiently. Wait until the projector is cool to the touch before changing any lamps. Before starting the installation be sure unplug the AC cord.ASK C60 XGA lamp cover, ASK 26 lamp

  • To access the lamp, turn over the ASK C60 XGA projector.
  • Loosen the 3 screws holding the lamp in place.
  • Grab the handle on the ASK Proxima LAMP-026 lamp cage and gently lift out the lamp. Place to one side.

  • ASK LAMP-026 lamps contains mercury and should sent to a local recycling program for proper disposal. Do not place into regular garbage.

ASK C60 XGA lamp cover, ASK 26 lamp

  • Take the new ASK Proxima LAMP-026 lamp. Don’t touch the bare bulb–the oil on your fingers can leave a black mark on the lamp affecting the projected image. Place the ASK Proxima LAMP-026into the projector.
  • Tighten the three screws on the new ASK LAMP-026 lamp.
  • You are ready to reset the Lamptimer.

 

 

 

 

STEP 3: Reset the Lamptimer

In order to properly track the lamp life of the newly installed ASK Proxima LAMP-026 in the ASK C60 XGA projector,  you must reset the Lamptimer. Failure to do so may result in the lamp being used longer than it’s lamp life.

ASK ASK C60 lamp reset menu, ASK LAMP-026ASK C60 XGA lamp reset icon, ASK LAMP-026

To reset the Lamptimer:

  • Open the MAIN MENU. Press ENTER.
  • Scroll down to the SERVICE menu. Press ENTER.
  • Scroll down to the Reset lamptimer option. Press ENTER.
  • The lamptimer icon will appear to show you have reset the timer.
Tagged with: , , , , , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓
ASK C20 SVGA projector, ASK 26 lamp

ASK C20 SVGA projector

ASK C20 SVGA projector alarm, ASK 26 lamp

The lamp in the ASK C20 SVGA projector has a life of between 1500 to 2000 hours. When it’s time to replace the ASK Proxima LAMP-026 for your ASK C20 SVGA projector, you’ll see the ALARM button on the projector light  red. A warning message will also appear on screen.

Follow our step-by-step guide for a quick and easy replacement of the ASK Proxima LAMP-026 in the ASK C20 SVGA projector.

Go with an authentic ASK LAMP-026

Protect your health and keep your projector warranty valid — install an authentic ASK LAMP-026.

Buy an ASK Proxima LAMP-026 from an authorized dealer and get the best lamp for your ASK C20 SVGA projector.  Beware of cheaper knock-off lamps that will damage the sensitive mechanisms in your ASK C20 SVGA projector. These counterfeit “compatible” lamps are often sold at discounted prices and may appear to be a  good deal but actually have a much shorter life span.

Due to their inferior materials and worksmanship, they are prone to exploding when installed into the projector. Copy-cat manufacturers are also using Krypton 85, a carcinogenic, radioactive material to create these generic “compatible” lamps.

Keep yourself and your projector safe by installing an authentic ASK Proxima LAMP-026 from a recgonized reseller.

How to install the ASK LAMP-026

Before starting turn off the projector and unplug the AC cord. Allow the ASK C20 SVGA projector to cool for one hour. There is a risk of burning yourself if you try to replace the ASK Proxima LAMP-026 before the projector has cooled down sufficiently.

ASK C20 SVGA lamp cover, ASK 26 lamp

  • Turn over the ASK C20 SVGA to access the lamp. Loosen the 3 screws holding the lamp in place.
  • Grab the handle on the ASK Proxima LAMP-026 lamp cage and gently lift out the lamp. Place to one side.

  • The ASK LAMP-026 lamp contains mercury and should sent to a local recycling program for proper disposal.

ASK C20 SVGA lamp cover, ASK 26 lamp

 

  • Take the new ASK Proxima LAMP-026 lamp. Avoid touching the bare bulb with as the oil on your finger can leave a black mark on the lamp affecting the projected image. Place it into the projector.
  • You are ready to reset the Lamptimer.

 

 

 

STEP 3: Resetting the Lamptimer

It’s important to reset the Lamptimer after replacing the ASK Proxima LAMP-026 in the ASK C20 SVGA projector in order that the lamp life be accurately tracked and recorded. Failure to do so may result in the lamp being used longer than it’s lamp life.

ASK C20 SVGA,, ASK LAMP-026ASK C20 SVGA lamp reset icon, ASK LAMP-026

To reset the Lamptimer:

  • Open the MAIN MENU. Press ENTER.
  • Scroll down to the SERVICE menu. Press ENTER.
  • Scroll down to the Reset lamptimer option. Press ENTER.
  • The lamptimer icon will appear to show you have reset the timer.
Tagged with: , , , , , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP — No Comments ↓
ASK C80 projector, ASK LAMP-026

ASK C80 projector

Change your ASK Proxima LAMP-026 in 3 easy steps by following our step-by-step guide.

Step 1: Finding the correct ASK LAMP-026

You’ll need to purchase an authentic ASK LAMP-026 from an authorized dealer.  Beware of cheaper knock-off lamps as they will damage the sensitive mechanisms in your ASK C80 projector. Although sold at discount prices, these generic “compatible” lamps have a much shorter life span due to their inferior materials and worksmanship. They are prone to explosions and contain cancer-causing materials, such as Krypton 85. Installing a knock-off lamp into your ASK C80 projector will also void your warranty.

Protect your health and keep your projector working properly — install an authentic ASK LAMP-026!

 STEP 2: Replacing the ASK LAMP-026 projector lamp

ASK C80 lamp replacement alarm, ASK LAMP-026

ASK C80 lamp replacement alarm

ASK C80 lamp warning message, ASK LAMP-026

ASK C80 lamp warning message

 

When it’s time to replace the ASK Proxima LAMP-026 for your ASK C80 projector, you’ll see the ALARM button on the projector light up red. A warning message will also appear on screen.

 

ASK C80 lamp cover, ASK LAMP-026

Step-by-step instructions for replacing the ASK LAMP-026

  • Turn off the projector and unplug the AC cord. These projectors operate under high temperatures and there is a risk of burning if the projector has not cooled enough. Allow the ASK C80 to cool for one hour.
  • The Lamp Cover for the ASK C80 is on the bottom of the projector. Gently turn it over and loosen the 3 screws holding the lamp in place.
  • Grab the handle on the ASK Proxima LAMP-026 lamp cage and gently lift out the lamp. Place to one side.

  • Don’t throw this lamp into the regular garbage as it contains mercury — send it to a local recycling program where it can be disposed of properly.

ASK C80 lamp replacement, ASK LAMP-026

  • Take the new ASK Proxima LAMP-026 lamp. Avoid touching the bare bulb; the oil on your finger can leave a black mark on the lamp affecting the projected image. Place it into the projector.
  • Tighten the two screws on the new ASK LAMP-026 lamp.
  • Put the lid back on. Tight the screw holding the lid in place.
  • Be sure to clean the filter.
  • You are ready to reset the Lamptimer.

 

 

STEP 3: Resetting the Lamptimer

It’s important to reset the Lamptimer after replacing the ASK Proxima LAMP-026 in the ASK C80 projector in order that the lamp life be accurately tracked and recorded. Failure to do so may result in the lamp being used longer than it’s lamp life.

ASK C80, ASK LAMP-026ASK C80 lamp reset icon, ASK LAMP-026

To reset the Lamptimer:

  • Open the MAIN MENU. Press ENTER.
  • Scroll down to the SERVICE menu. Press ENTER.
  • Scroll down to the Reset lamptimer option.
  • Press ENTER.
  • The lamptimer icon will appear to show you have reset the timer.

 

Tagged with: , , , , , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓
ASK C100 projector, ASK LAMP-026

ASK C100 projector

Replacing the ASK C100/C90 projector lamp is quick and easy when you follow our step-by-step guide. Change your ASK Proxima LAMP-026 in 3 easy steps!

Step 1: Finding the correct ASK LAMP-026

ASK C100/C90 lamp replacement alarm, ASK LAMP-026

ASK C100/C90 lamp warning message, ASK LAMP-026

ASK C100/C90 lamp warning message

 

When it’s time to replace the ASK LAMP-026 for your ASK C100/C90 projector, you’ll see the ALARM button on the projector light up red. A warning message will also appear on screen.

Go with authentic

Buy an ASK Proxima LAMP-026 from an authorized dealer and get the best lamp for your ASK C100/C90 projector.  Beware of cheaper knock-off lamps that will damage the sensitive mechanisms in your ASK C100/C90 projector. These counterfeit “compatible” lamps are often sold at discounted prices and may appear to be a  good deal. They actually have a much shorter life span and may be prone to exploding due to their inferior materials and worksmanship. Lacking the correct materials, copy-cat manufacturers are also using cancer-causing materials, such as Krypton 85, to get the same results as the OEM manufactured lamps.

Protect your health and keep your projector warranty valid — install an authentic ASK Proxima LAMP-026 . You’ll be protected should there be any problems.

 STEP 2: Replacing the ASK LAMP-026 projector lamp

ASK C100/C90 lamp cover, ASK LAMP-026

  • Turn off the projector and unplug the AC cord. Allow the ASK C100/C90 projector to cool for one hour – it should be cool to the touch. Inside the projector can be very hot since these machines operator under high temperatures and there is a risk of burning if the projector has not cooled enough.
  • The ASK C100/C90 Lamp Cover is found under the projector. Gently turn it over and loosen the 3 screws holding the lamp in place.
  • Grab the handle on the ASK Proxima LAMP-026 lamp cage and gently lift out the lamp. Place to one side.

  • Don’t throw this lamp into the regular garbage as it contains mercury — send it to a local recycling program where it can be disposed of properly.

ASK C100/C90 lamp replacement, ASK LAMP-026

  • Take the new ASK LAMP-026 lamp. Avoid touching the bare bulb since the oil on your finger can leave a black mark on the lamp affecting the projected image. Place it into the projector.
  • Tighten the three screws on the new ASK Proxima LAMP-026 lamp.
  • Be sure to clean the filter.
  • You are ready to reset the Lamptimer.

 

STEP 3: Resetting the Lamptimer

It’s important to reset the Lamptimer after replacing the ASK LAMP-026 in the ASK C100/C90 projector in order that the lamp life be accurately tracked and recorded. Failure to do so may result in the lamp being used longer than it’s lamp life.

ASK C100/C90, ASK LAMP-026ASK C100/C90 lamp reset icon, ASK LAMP-026

To reset the Lamptimer:

  • Open the MAIN MENU. Press ENTER.
  • Scroll down to the SERVICE menu. Press ENTER.
  • Scroll down to the Reset lamptimer option. Press ENTER.
  • The lamptimer icon will appear to show you have reset the timer.
Tagged with: , , , , , , , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓
ASK Proxima UltraLight LX2 projector, ASK LAMP-019, (POA-LMP21J service parts no 610 280 6939)

ASK Proxima UltraLight LX2 projector

Wondering when to replace the ASK Proxima UltraLight LX2 projector lamp? Watch for these signs:

  • The LAMP REPLACEMENT indicator on the projector lights yellow
  • Images appear dark
  • Images have unnatural color
  • Warning message about the lamp life appear on the screen.

If any of these signs appear replace the ASK LAMP-019, (POA-LMP21J service parts no 610 280 6939) immediately.

Replace the ASK LAMP-019 in 3 easy steps by following our step-by-step guide.

Go with authentic

While knock-off “compatible” lamps may seem like a bargain they may actually end up costing you more in the long run. These lamps have been created with inferior materials and are prone to explosions. Copy-cat manufacturers are using carcinogenic substances in order to achieve the same effects as OEM manufacturers.  Read more about the dangers of knock-off lamps.

Don’t take chances with knockoff lamps. Invest in an authentic ASK LAMP-019, (POA-LMP21J service parts no 610 280 6939) created with the proper materials by manufacturers who take pride in their products. These authentic lamps are manufactured to work in harmony with your ASK Proxima UltraLight LX2 projector. Should you have any problems with the ASK LAMP-019, you’re guaranteed a refund as well as technical support.

Skip the hassles and health hazards by buying an authentic OEM ASK LAMP-019, (POA-LMP21J service parts no 610 280 6939). It’s worth the peace of mind.

Replacing the ASK LAMP-019 lamp

ASK Proxima UltraLight LX2 lamp cover, ASK LAMP-019, (POA-LMP21J service parts no 610 280 6939)

ASK Proxima UltraLight LX2 replace ASK LAMP-019, (POA-LMP21J service parts no 610 280 6939)

Reset the Lamp Replacement Monitor Timer

After replacing the lamp be sure to reset the Lamp Replacement Monitor Timer so your projector can accurately track the number of hours left on your new lamp.

To reset the timer:

Press the MENU button so the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT button to reach the SETTING option.
Press the SELECT button to open the SETTING MENU.
Move down to the LAMP AGE option. Press the SELECT button to display the “Lamp replace monitor reset?” option.
Select YES. The timer is now reset.

Prolong the life of your newly installed ASK LAMP-019, (POA-LMP21J service parts no 610 280 6939) by regularly cleaning the air filters and letting the projector to cool down before turning it off.

Tagged with: , , , , , , , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — 4 Comments ↓
ASK Proxima UltraLight LS2, ASK LAMP-019, (POA-LMP21J service parts no 610 280 6939)

ASK Proxima UltraLight LS2 projector

ASK LAMP-019, (POA-LMP21J service parts no 610 280 6939)The LAMP REPLACEMENT indicator on your ASK Proxima UltraLight LS2 projector will light up yellow when it’s time for a new lamp. Images that appear dark or with unnatural color are also warning signs that the ASK LAMP-019, (POA-LMP21J service parts no 610 280 6939) lamp needs to be replaced.

Replace the ASK LAMP-019 in 3 easy steps by following our step-by-step guide.

STEP 1: Finding the correct lamp

Don’t take chances with knockoff lamps. Invest in an authentic ASK LAMP-019, (POA-LMP21J service parts no 610 280 6939) created with the proper materials by manufacturers who take pride in their products. These authentic lamps are manufactured to work in harmony with your ASK Proxima UltraLight LS2 projector. Should you have any problems with the ASK LAMP-019, you’re guaranteed a refund as well as technical support.

While knock-off “compatible” lamps may seem like a bargain they may actually end up costing you more in the long run. These lamps have been created with inferior materials and are prone to explosions. Copy-cat manufacturers are using carcinogenic substances in order to achieve the same effects as OEM manufacturers.  Read more about the dangers of knock-off lamps.

Skip the hassles and health hazards by buying an authentic OEM ASK LAMP-019, (POA-LMP21J service parts no 610 280 6939). It’s worth the peace of mind.

STEP 2: Replacing the ASK LAMP-019 lamp

ASK Proxima UltraLight LS2 lamp cover, ASK LAMP-019, (POA-LMP21J service parts no 610 280 6939)

ASK Proxima UltraLight LS2 replace ASK LAMP-019, (POA-LMP21J service parts no 610 280 6939)

 
 

STEP 3: Resetting the Lamp Replacement Monitor Timer

After replacing the lamp be sure to reset the Lamp Replacement Monitor Timer so your projector can accurately track the number of hours left on your new lamp.

To reset the timer:

Press the MENU button so the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT button to reach the SETTING option.
Press the SELECT button to open the SETTING MENU.
Move down to the LAMP AGE option. Press the SELECT button to display the “Lamp replace monitor reset?” option.
Select YES. The timer is now reset.

Prolong the life of your newly installed ASK LAMP-019, (POA-LMP21J service parts no 610 280 6939) by regularly cleaning the air filters and letting the projector to cool down before turning it off.

Tagged with: , , , , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓
ASK Proxima LAMP-016 (POA-LMP24 Service Parts No. 610 282 2755)

ASK Proxima LAMP-016 (POA-LMP24 Service Parts No. 610 282 2755)

The ASK Proxima LAMP-016 lamp should have a life that lasts between 1500 -2000 hours before needing to be replaced. When it’s reaching its end of life, The Lamp Replacement Indicator on the projector’s panel will light up orange.

Also install a genuine ASK Proxima LAMP-016 (POA-LMP24 Service Parts No. 610 282 2755) from a recognized OEM manufacturer. Generic/knockoff/compatible lamps can damage the sensitive (and expensive) mechanisms in your projector. They give poor illumination and are prone to explosions, which may expose you and your audience to the carcinogenic substance Krypton-85 used in the making of these counterfeit lamps.

Installing a generic lamp will also void any warranty for your ASK Proxima projectors. Go with an authentic ASK Proxima LAMP-016 (POA-LMP24 Service Parts No. 610 282 2755. Learn the 7 Ways to spot a counterfeit lamp.

Compatible Projectors

The ASK Proxima LAMP-016 (POA-LMP24 Service Parts No. 610 282 2755) is compatible with:

ASK Proxima DP-9240

ASK Proxima DP-9260

 

For step-by-step instructions on replacing your ASK Proxima LAMP-016 (POA-LMP24 Service Parts No. 610 282 2755 projector lamp, click on your projector listed below:

 

ASK Proxima DP-9240 projector, ASK Proxima LAMP-016

ASK Proxima DP-9240 projector

Click here for step-by-step instructions on how to change the ASK Proxima LAMP-016 projector lamp for the ASK Proxima DP-9240 projector.

 

 

 

 

ASK Proxima DP-9260 projector, ASK Proxima LAMP-016

ASK Proxima DP-9260 projector

Click here for step-by-step instructions on how to change the ASK Proxima LAMP-016 projector lamp for the ASK Proxima DP-9260 projector.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Tagged with: , , , , , , , , , , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓
ASK Proxima DP-9260 projector, ASK Proxima LAMP-016

ASK Proxima DP-9260 projector

Follow our 3-step guide to a new ASK Proxima DP-9260 projector lamp!

STEP ONE: Finding the correct lamp

When the ASK Proxima LAMP-016 is reaching end of life the Lamp Replacement Indicator on the front panel will light up orange. Replace the lamp immediately to prevent any malfunctions in your ASK Proxima DP-9260 projector.

Avoid knock-off “compatible” lamps as these lamps have been created with inferior materials and are prone to explosions. Be sure to buy your replacement ASK Proxima LAMP-016 from an authentic source to protect both your ASK Proxima DP-9260 projector but also your health. Copy-cat manufacturers are using carcinogenic substances in order to achieve the same effects as OEM manufacturers.  Read more about the dangers of knock-off lamps.

Buying from an authentic source guarantees you a lamp created with the proper materials by manufacturers who take pride in their products. Should you have any problems with the lamp, you’re also guaranteed a refund as well as technical support.

STEP TWO: Replacing the ASK Proxima LAMP-016lamp

ASK Proxima DP-9260, ASK Proxima LAMP-016

  • Disconnect the power cord.  The ASK Proxima DP-9260 operates under high heat so allow it to cool for at least one hour before replacing the lamp. Your run the risk of a severe burn replacing the lamp while the projector is still hot.
  • The lamp lid for the ASK Proxima DP-9260 is found on the bottom of the projector. Turn the projector on its side and remove the screw holding the lamp lid in place.
  • Unscrew the two screws holding the ASK Proxima LAMP-016 lamp holder in place.
  • Gently grab the lamp holder and pull out the ASK Proxima LAMP-016. Use your local recycling program to dispose of the used ASK Proxima LAMP-016.ASK Proxima DP-9260, ASK Proxima LAMP-016

 

  • Don’t throw the used ASK Proxima LAMP-016 lamp into regular garbage as it contains mercury. The lamp should be properly recycled.

  • Inset the new ASK Proxima LAMP-016 lamp all the way into the ASK Proxima DP-9260 projector.
  • Tighten the two screws that hold the LAMP-016 lamp in place.
  • Replace the lamp lid and tighten the screw holding the lamp lid in place.

 

STEP THREE: Resetting the lamp timer

In order for the ASK Proxima DP-9260 to correctly track the lamp life of your newly installed ASK Proxima LAMP-016 lamp, you’ll need to reset the timer.

ASK Proxima DP-9260 lamp reset, ASK Proxima LAMP-016

  • Press the MENU button to display the MAIN MENU option.
  • Scroll across the top menu to the SETTING menu. Another pull down menu will appear.
  • Press the POINT DOWN arrow.
  • Move down to select the LAMP AGE open. Press SELECT.

ASK Proxima DP-9260, ASK Proxima LAMP-016

 

 

 

  • A second confirmation message “Lamp replace monitor Reset?” will be displayed.
  • Select YES. A second dialogue message appear OK?
  • Move the arrow to the YES.
  • Press the SELECT button.

The lamp replace monitor has now been reset.

Tagged with: , , , , , , , , , , , ,
Join the discussion on Facebook! All your questions, answered! The Screen & Projector Group