About Us - Page 229 of 274 - DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP

When to replace the POA-LMP48 (610 301 7167) projector lamp

Shelagh McNallyPosted on April 3, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Sanyo POA-LMP48 (service part no 610 301 7167)

The life expectancy of your Sanyo POA-LMP48 (service part no 610 301 7167) lamp depends on the amount of usage and whether the air filters are cleaned on a regular basis. A build up of dust on the filters will reduce the cooling fans effectiveness and may cause the lamp to overheat.

The life of the Sanyo POA-LMP48 (service part no 610 301 7167) lamp runs anywhere from 1,000 to 3,000 hours. It’s always a good idea to keep a spare lamp on hand so you can replace the lamp immediately and not wait to use the projector.

The best type of lamp to buy is one that has been guaranteed authentic and created by approved manufacturers who use the correct parts for the lamp. Knock-off lamps use counterfeit parts that can explode inside the projector or not fit properly thereby damaging the sensitive mechanism in the projector. The initial low cost of these counterfeit lamps may end up costing you more money in the long run if your projector is ruined. Buy an authentic Sanyo POA-LMP48 (service part no 6103017167) will maintain your warranty while providing you with a manufacturer’s guarantee.

Looking for a less expensive option? Are you technically adept? Watch our step-by-step video on replacing only the Sanyo POA-LMP48 (service part no 610 301 7167) bulb instead of the entire lamp housing.

The Sanyo POA-LMP48 (service part no 610 301 7167) can be used in the following projectors:

For step-by-step instructions on how to replace the Sanyo POA-LMP48 (610 301 7167)4 projector lamp, please click on your specific model listed below:

Click here for step-by-step instructions on how to change the Sanyo POA-LMP48 (service part no 610 301 7167) projector lamp for the Sanyo PLC-XT10 projector.

Click here for step-by-step instructions on how to change the Sanyo POA-LMP48 (service part no 610 301 7167) projector lamp for the Sanyo PLC-XT15 projector.

Prolong the life of your new Sanyo POA-LMP48 (6103017167) lamp

To maintain the life of your newly installed Sanyo POA-LMP48 (service part no 610-301-7167), follow these three suggestions:

Wait at least five minutes before turning the Sanyo PLC-XT10 projector off.
Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
Clean the air filters regularly so the projector won’t overheat putting undue stress on on the Sanyo POA-LMP48 (service part no 610-301-7167) lamp.

Tagged with: authentic projector lamps, genuine projector lamps, philips, replacement projector lamps, Sanyo PLC-XT10 projector, Sanyo PLC-XT15 projector, Sanyo POA-LMP48 (service part no 610 301 7167)

Replace the lamps in your Sanyo PLC-XF20 projector

Shelagh McNallyPosted on April 3, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Your Sanyo PLC-XF20 projector is equipped with four projector lamps. This guide shows you how to replace them

Signs of end of projector lamp

There is a Lamp Replace Indicator at the front and at the back of the Sanyo PLC-XF20 projector. When any four of the projector lamp is nearing end of life, these indicators will flash yellow. In order to determine which of the four Sanyo POA-LMP29 (service part no 6102844627) projector lamps needs to be replaced, you’ll need to consult the Lamp Status Display on the Sanyo PLC-XF20 projector screen.

Buy authentic projector lamps

Buy an authentic Sanyo POA-LMP29 (6102844627) projector lamp and make life easier. Generic lamps look like a great bargain but these knock-off lamps are created with inferior materials making them susceptible to explosions when installed. They also have a shorter life span and can damage the precise components in your Sanyo PLC-XF20 projector. Learn more about spotting dangerous projector lamps by reading our article: 7 tips for spotting counterfeits.

LAMP STATUS DISPLAY SETTINGS

The Lamp Status Display shows the status of each Sanyo POA-LMP29 (service part no 610-284-4627) lamp:

Yellow Lamp: projector lamp is lighting normally.
Dim Lamp: projector lamp is off
Red Lamp: projector is nearing end of life and should be replaced.
X Mark on Lamp: the lamp is not functioning and needs to be replaced immediately.

LAMP MANAGEMENT FUNCTION

The Lamp Management Function automatically changes the combinations of lighting lamps by detecting which lamps are still working.

When any of the four Sanyo POA-LMP29 projector lamp goes out, Lamp Mode will automatically switch from using four Sanyo POA-LMP29 (service part no 610 284 4627) lamps to using two lamps.

When any of the two Sanyo POA-LMP29 (service part no 610-284-4627) projector lamp is out, the projector will operate using only one lamp.

INSTALLING THE NEW SANYO POA-LMP29 LAMP

NOTE: Make sure of the number of lamps that need to be replaced by referring to the Lamp Status Display and the Lamp Management Function.

Remove the two screws on the Sanyo PLC-XF20 Lamp Cover and press the top button to open the Lamp Cover.
Choose which lamp needs to be replaced. BE SURE TO PICK THE CORRECT PROJECTOR LAMP THAT NEEDS TO BE REPLACED.
Loosen the two screws holding the Sanyo POA-LMP29 (service part no 610 284 4627) projector lamp in place.
Grasp the handle and gently pull out the defective Sanyo POA-LMP29 lamp. Place to one side. Be sure to dispose of the used Sanyo POA-LMP29 (6102844627) projector lamp through a local recycling program. Don’t throw this projector lamp into the regular garbage as it contains mercury.
Take the new Sanyo POA-LMP29 projector lamp by the handle and gently guide it into place.
Tighten the two screws holding the Sanyo POA-LMP29 (service part no 610-284-4627) projector lamp assembly in place.
Replace the Sanyo PLC-XF20 Lamp Cover and tighten the two screws to put the lamp cover back in place.
Reset the Lamp Counter following the instructions below.

Reset the projector lamp counter

Turn the Sanyo PLC-XF20 projector on.
Press the MENU buttons to open the ON-SCREEN MENU.
Press POINT LEFT/RIGHT button to get the red frame pointer to move to the SETTING menu icon.
Press POINT DOWN button to projector Lamp counter reset. Press SELECT.
Move the arrow to the replaced lamp number (Lamp 1, Lamp 2, Lamp 3 or Lamp 4). Press SELECT. BE SURE TO RESET THE CORRECT LAMPS
The message “Lamp replace counter Reset?” will be displayed with YES or NO underneath.
Move the pointer to YES. Press the SELECT button.
Move to the second confirmation box and select YES.

NOTE: BE SURE TO RESET THE CORRECT PROJECTOR LAMP otherwise the lamp replace indicator will continue lighting YELLOW.

RESETTING THE Sanyo POA-LMP29 (610 284 4627) PROJECTOR LAMP MODE

You can set the lamp mode to use either four lamps or two lamps. Using 2 lamps will prolong the life of the projector lamps.

To change the lamp mode:
Press MENU button so the ON-SCREEN Menu will appear.
Using the POINT LEFT/RIGHT button move to SETTING. Press SELECT button.
A second dialog screen appears.
Press the POINT DOWN button to move to LAMP MODE.
4 lamps mode using all lamps. Picture will become brighter.
2 lamps mode using only 2 lamps. Picture will become darker
NOTE: You must wait 90 seconds after changing the Lamp Mode before changing it again.

Tips to make your Sanyo POA-LMP29 projector lamp last longer

Extend the life of your newly installed Sanyo POA-LMP29 (service part no 610-284-4627) by following these helpful tips:

Wait at least five minutes before turning the Sanyo PLC-XF20 projector off.
Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP29 (6102844627) and prevent the Sanyo PLC-XF20 projector from overheating.

Looking for a less expensive option? Are you technically saavy? Watch our step-by-step video on replacing only the Sanyo POA-LMP29 bulb instead of the entire lamp housing.

Tagged with: authentic projector lamps, Projector LAMP, replacement projector lamps, Sanyo PLC-XF20 projector, Sanyo POA-LMP29 (service part no 610 284 4627)

How to install your new Sanyo PLC-XT10 projector lamp

Shelagh McNallyPosted on April 2, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

STEP-BY-STEP INSTRUCTIONS FOR SANYO PLC-XT10 LAMP REPLACEMENT

When it’s time to change your lamp on your Sanyo PLC-XT10 projector, you’ll notice the yellow light blinking on the Lamp Replacement Indicator.

Be sure to buy an authentic Sanyo POA-LMP48 (service part no 610 301 7167) for your replacement lamp bought from a verified source. Buying an authentic replacement lamp will ensure that you’re installing a lamp manufactured with work properly and not damage your projector. Resist the temptation to buy a cheaper counterfeit model as this can damage the sensitive mechanisms in your Sanyo PLC-XT10 projector.

Looking for a less expensive option? Are you technically adept? Watch our step-by-step video on replacing only the Sanyo POA-LMP48 (service part no 610 301 7167) bulb instead of the entire lamp housing

Before Installing the Sanyo POA-LMP48 Projector Lamp

1. Turn off the projector and unplug the AC cord.
2. Allow the Sanyo PLC-XT10 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures. Without letting the projector cool properly there is burn danger.

Replacing the Sanyo POA-LMP48 (6103017167) Lamp Assembly

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

At the back of the Sanyo PLC-XT10 projector you’ll find the Lamp Cover. Using a Philips screwdriver loosen the screw holding the cover in place. Put the cover to one side.
Remove the two screws on either side of each of the Sanyo POA-LMP48 (service part no 610-301-7167) lamp. Grab the handle on the lamp cage and gently pull the lamp out. Place the used lamp to one side. Be sure to dispose of the used lamp through a local recycling program. Don’t throw this lamp into the regular garbage as it contains mercury.

Take the new Sanyo POA-LMP48 (service part no 6103017167) lamp cage by the handle and gently manuever it into place.
Avoid touching the glass or the bulb. It should slide it easily – don’t force it. Tighten the two screws on the Lamp Assembly. Make sure they are tightened properly otherwise the projector will not turn back on.
Replace the Lamp Cover and tighten the screw. Let the projector stand for five minutes so the lamp can stabilize. Re-connect the power cord and turn the Sanyo PLC-XT10 projector on. If the projector doesn’t turn, check that all the screws have been tightened. Try repeating the installation steps.

NOTE: Your old Sanyo POA-LMP48 (service part no 610-301-7167) lamp should be properly recycled. These lamps contain mercury and can’t be placed into common garbage.

Reset the Sanyo PLC-XT10 Lamp Replacement Counter

Reset the Lamp Replacement Counter only when the Sanyo POA-LMP48 (service part no 610-301-7167) lamp has been replaced.

Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Turn the Sanyo PLC-XT10 projector on.
Press the Menu option so the On-Screen Menu will appear.
Press Point left/right button(s) to move a red frame poster to Setting Menu icon.
Press Point Down button to move the red frame pointer to Lamp counter reset.
Press the Select button. The message “Lamp replace counter Reset?” will be displayed.
Move the pointer to YES and then press Select button.

Prolong the life of your new Sanyo POA-LMP48 (6103017167) lamp

To maintain the life of your newly installed Sanyo POA-LMP48 (service part no 610-301-7167), follow these three suggestions:

Wait at least five minutes before turning the Sanyo PLC-XT10 projector off.
Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
Clean the air filters regularly so the projector won’t overheat putting undue stress on on the Sanyo POA-LMP48 (service part no 610-301-7167) lamp.

Tagged with: authentic projector lamps, genuine projector lamps, POA-LMP48 (6103017167), replacement projector lamps, Sanyo PLC-XT10 projector, Sanyo POA-LMP48 (service part no 610 301 7167)

3 Easy steps to replace the Sanyo PLC-XT15 projector lamp

Shelagh McNallyPosted on April 2, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Sanyo PLC-XT15 projector

Replace your Sanyo PLC-XT15 projector lamp in 3 easy steps.

If the picture on your Sanyo PLC-XT15 projector is dim or looks unnatural the Sanyo POA-LMP48 (service part no 610 301 7167) is reaching its end of life. You may also notice the Replace Lamp Indicator light on the front panel is yellow. Replace the Sanyo POA-LMP48 in the Sanyo PLC-XT15 projector easily following the step-by-step below.

The lifespan of your Sanyo POA-LMP48 (service part no 610 301 7167) lamp will vary depending on how much the projector is used and if the filters are cleaned regularly.

Looking for a less expensive option? Are you technically adept? Watch our step-by-step video on replacing only the Sanyo POA-LMP48 (service part no 610 301 7167) bulb instead of the entire lamp housing

STEP ONE: Purchasing the correct projector lamp

The best thing you can do to prolong the life of your Sanyo PLC-XT15 and save money is to invest in an original Sanyo POA-LMP48 (service part no 6103017167) projector lamp. Generic lamps look like a great bargain since they are generally cheaper, however, these knock-off lamps are created with inferior materials. They are susceptible to explosions, have a shorter life span and can damage the precise components in your Sanyo PLC-XT15 projector. Installing a knock-off generic lamp also voids your warranty. Learn more about spotting dangerous projector lamps by reading our article: 7 tips for spotting counterfeits.

Looking for a less expensive option? Are you technically adept? Watch our step-by-step video on replacing only the Sanyo POA-LMP48 (service part no 610 301 7167) bulb instead of the entire lamp housing.

STEP TWO: Installing the new Sanyo POA-LMP48 (6103017167) lamp

Allow the Sanyo PLC-XT15 projector to thoroughly cool before changing the lamp. Turn off the projector, unplug the AC cord and allow 45 to 60 minutes for the projector to cool. These projectors operate under high heat and there is a possibility of being burned, if the projector is not fully cooled before changing the Sanyo POA-LMP48 (service part no 610 301 7167) lamp.
The lamp cover for the Sanyo PLC-XT15 is at the bottom of the projector. Gently turn projector over and loosen the screw holding the cover in place. Place the cover to one side.
Inside you’ll find the Sanyo POA-LMP48 (service part no 610-301-7167) lamp cage. Loosen both screws holding the lamp cage in place. Grab the lamp handle and gently lift the lamp out of its socket. Place to one side. Be sure to dispose of the used lamp through a local recycling program. Don’t throw this lamp into the regular garbage as it contains mercury.

Taking the new Sanyo POA-LMP48 lamp assembly by the handle place it into the slot. Avoid touching the actual bulb as the oil from your fingers can burn a black spot on the lenses or you can accidentally break the bulb. Don’t force the lamp into place — it should slide into the slot easily.
Once the lamp is in, tighten both screws on the Sanyo POA-LMP48 (service part no 6103017167) lamp assembly. Make sure the screws have been tightened properly or the Sanyo PLC-XT15 projector will not turn on.
Replace the Lamp Cover and tighten the screw. Re-connect the power cord and turn on the Sanyo PLC-XT15 projector If the Sanyo POA-LMP48 lamp does not turn on after the warm-up period, try re-installing the lamp.
Reset the Lamp Replacement Counter by following the instructions below.

NOTE: Your old Sanyo POA-LMP48 (service part no 610-301-7167) lamp should be properly recycled. These lamps contain mercury and can’t be placed into common garbage.

STEP THREE: Reset the Sanyo PLC-XT15 Lamp Replace Counter

The Lamp Replacement Counter for the Sanyo PLC-XT15 will track the correct age of your newly installed lamp and trigger the Lamp Replace Indicator. Failure to reset the counter may result in the projector not tracking the end of life for the Sanyo POA-LMP48 (service part no 6103017167) and letting the projector inadvertently use the lamp past its normal life cycle. Your Sanyo PLC-XT15 may stop working suddenly if the Lamp Replace Counter has not been properly set.

Press the MENU Button to display the MAIN MENU. Press the POINT LEFT/RIGHT button and scroll right to select SETTING.
Press the SELECT button to display the SETTING DISPLAY menu.
Press the POINT DOWN button (a red arrow will appear).
Move the red arrow to the LAMP AGE and then press the SELECT button.
The message “Lamp replace counter reset?” appears. Move the arrow down to YES and press the SELECT button.
Move the arrow to QUIT and press the SELECT button.

Extend the life of the Sanyo POA-LMP48 projector lamp

Extend the life of your newly installed Sanyo POA-LMP48 (service part no 610 301 7167) by following these helpful tips:

Wait at least five minutes before turning the Sanyo PLC-XT15 off.
Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP48 (service part no 6103017167) and prevent the Sanyo PLC-XT15 projector from overheating.

Tagged with: authentic projector lamps, Sanyo PLC-XT15 projector, Sanyo POA-LMP48 (service part no 610 301 7167), Sanyo POA-LMP48 (service part no 6103017167

Lifespan of the Sanyo POA-LMP42 projector lamp

Shelagh McNallyPosted on April 1, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

The Sanyo POA-LMP42 (service part 610-292-4831) should last between 1,000 to 3,000 hours. The exact lifespan of a genuineany Sanyo POA-LMP42 will vary depending on how much your projector is used and how regularly the air filters are cleaned. (Clogged air filters cause the projector to heat up and this puts stress on the lamp.)

If you’re using a knock-off lamp you can expect far less time. In fact, you may be putting your projector at risk using these generic brands. Not only do they not last as long, they can damage the inside mechanism in your projector. Installing knock-off lamps also voids the warranty on your projector and should these lamps explode or cause any damage you’ll not be covered. Walk away from lamps with a price tag that seems too good to be true. The few dollars you save are not worth, especially if the knock-off explodes inside your computer. Learn the 7 tips for spotting counterfeits lamps and protect yourself.

Projectors compatible with the Sanyo POA-LMP42 projector lamp:

Sanyo PLC-UF10

Sanyo PLC-XF40

Sanyo PLC-XF41

For step-by-step instructions on replacing your Sanyo POA-LMP42 lamp, click on your model listed below:

Click here for step-by-step instructions on how to change the Sanyo POA-LMP42 (service part 610-292-4831)projector bulb for the Sanyo PLC-UF10 projector.

Sanyo PLC-XF40

Click here for step-by-step instructions on how to change the Sanyo POA-LMP42 (service part 610-292-4831) projector bulb for the Sanyo PLC-XF40 projector.

Click here for step-by-step instructions on how to change the Sanyo POA-LMP42 (service part 610-292-4831) projector bulb for the Sanyo PLC-XF41 projector.

Tagged with: authentic lamps, authentic projector lamps, genuine lamps, genuine projector lamps, Lamp replacement, replacement projector lamps, Sanyo PLC-UF10 projector, Sanyo PLC-XF40 projector, Sanyo PLC-XF41, Sanyo POA-LMP42 6102924831, Sanyo POA-LMP42 service part 610-292-4831

Six steps to replacing lamps in the Sanyo PLC-XF41 projector

Shelagh McNallyPosted on March 30, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — 2 Comments ↓

Sanyo PLC-XF41 projector

Your Sanyo PLC-XF41 projector is equipped to operate with four Sanyo POA-LMP42 (service part 610-292-4831) projector lamps. The Lamp Replace Indicator at the front and at the back of the projector will flash yellow when any of the four projector lamps is nearing the end of its life. To find the specific Sanyo POA-LMP42 that needs to be replaced, you’ll need to consult the Lamp Status Display projector screen.

Protect your Sanyo PLC-XF41 from unnecessary damage by installing an authentic Sanyo POA-LMP42 (service part 6102924831) projector lamp. When you buy OEM projector lamps you’re guaranteed a Sanyo POA-LMP42 that has been made with parts to fit the specifications of your projector. lamp that and make life easier. Generic lamps look like a great bargain but these knock-off lamps are created with inferior materials making them susceptible to explosions when installed. Learn more about spotting dangerous projector lamps by reading our article: 7 tips for spotting counterfeits.

LAMP STATUS DISPLAY SETTINGS

The Lamp Status Display shows the status of each Sanyo POA-LMP42 (service part 6102924831) lamp:

LAMP MANAGEMENT FUNCTION

The Lamp Management Function automatically changes the combinations of lighting lamps by detecting which lamps are still working.

When any of the four Sanyo POA-LMP42 lamps goes out, Lamp Mode will automatically switch from using four Sanyo POA-LMP42 (6102924831) lamps to using two lamps.

When any of the two Sanyo POA-LMP42 (service part no 610-292-4831) lamps are out, the projector will operate using only one lamp.

INSTALLING THE NEW SANYO POA-LMP42 LAMP

NOTE: Make sure of the number of lamps that need to be replaced by referring to the Lamp Status Display and the Lamp Management Function.

Remove the two screws on the Sanyo PLC-XF41 Lamp Cover.
Press the top button to open the Lamp Cover.
Choose which lamp needs to be replaced. BE SURE TO PICK THE CORRECT LAMP THAT NEEDS TO BE REPLACED.
Loosen the two screws holding the Sanyo POA-LMP42 (service part no 610-292-4831) lamp in place.
Grasp the handle and gently pull out the defective Sanyo POA-LMP42 lamp. Place to one side. Be sure to dispose of the used Sanyo POA-LMP42 lamp through a local recycling program. Don’t throw this lamp into the regular garbage as it contains mercury.
Take the new Sanyo POA-LMP42 lamp by the handle and gently guide it into place.
Tighten the two screws holding the Sanyo POA-LMP42 (service part 6102924831) lamp assembly in place.
Replace the Sanyo PLC-XF41 Lamp Cover and tighten the two screws to put the lamp cover back in place.
Reset the Lamp Counter following the instructions below.

LAMP COUNTER RESET FOR SANYO PLC-XF41

Turn the Sanyo PLC-XF40 projector on.
Press the MENU buttons to open the ON-SCREEN MENU.
Press POINT LEFT/RIGHT button to get the red frame pointer to move to the SETTING menu icon.
Press POINT DOWN button to Lamp counter reset. Press SELECT.
Move the arrow to the replaced lamp number (Lamp 1, Lamp 2, Lamp 3 or Lamp 4). Press SELECT. BE SURE TO RESET THE CORRECT LAMPS
The message “Lamp replace counter Reset?” will be displayed with YES or NO underneath.
Move the pointer to YES. Press the SELECT button.
Move to the second confirmation box and select YES.

NOTE: BE SURE TO RESET THE CORRECT LAMP otherwise the lamp replace indicator will continue lighting YELLOW.

RESETTING THE SANYO POA-LMP42 (6102924831) LAMP MODE

You can set the lamp mode to use either four lamps or two lamps. Using 2 lamps will prolong the life of the projector lamps.
To change the lamp mode:
Press MENU button so the ON-SCREEN Menu will appear.
Using the POINT LEFT/RIGHT button move to SETTING. Press SELECT button.
A second dialog screen appears.
Press the POINT DOWN button to move to LAMP MODE.
4 lamps mode using all lamps. Picture will become brighter.
2 lamps mode using only 2 lamps. Picture will become darker
NOTE: You must wait 90 seconds after changing the Lamp Mode before changing it again.

Tips to make your Sanyo POA-LMP42 lamps last longer

Extend the life of your newly installed Sanyo POA-LMP42 (service part no 610-292-4831) by following these helpful tips:

Wait at least five minutes before turning the Sanyo PLC-XF41 projector off.
Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP42 (service part no 610-292-4831) and prevent the Sanyo PLC-XF41 projector from overheating.

Tagged with: authentic projector lamps, genuine projector lamps, Lamp replacement, replacement lamps, replacement projector lamps, Sanyo PLC-XF41, Sanyo POA-LMP42 service part no 610-292-483

Changing the lamps in your Sanyo PLC-XF40 projector

Shelagh McNallyPosted on March 30, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Sanyo PLC-XF40

Your Sanyo PLC-XF40 projector has four Sanyo POA-LMP42 (service part 610-292-4831) projector lamps. When any of the four projector lamps is nearing the end of its life, the Lamp Replace Indicator at the front and at the back of the projector will flash yellow. This only lets you know one of the lamps is about to go. In order to find out exactly which one of the four Sanyo POA-LMP42 projector lamps needs to be replaced, you’ll need to consult the Lamp Status Display projector screen.

Protect your Sanyo PLC-XF40 from unnecessary damage by installing an authentic Sanyo POA-LMP42 (service part 6102924831) projector lamp. When you buy OEM projector lamps you’re guaranteed a Sanyo POA-LMP42 that has been made with parts to fit the specifications of your projector. lamp that and make life easier. Generic lamps look like a great bargain but these knock-off lamps are created with inferior materials making them susceptible to explosions when installed. Learn more about spotting dangerous projector lamps by reading our article: 7 tips for spotting counterfeits.

LAMP STATUS DISPLAY SETTINGS

The Lamp Status Display shows the status of each Sanyo POA-LMP42 (service part 6102924831) lamp:

LAMP MANAGEMENT FUNCTION

The Lamp Management Function automatically changes the combinations of lighting lamps by detecting which lamps are still working.

When any of the four Sanyo POA-LMP42 lamps goes out, Lamp Mode will automatically switch from using four Sanyo POA-LMP42 (6102924831) lamps to using two lamps.

When any of the two Sanyo POA-LMP42 (service part no 610-292-4831) lamps are out, the projector will operate using only one lamp.

INSTALLING THE NEW SANYO POA-LMP42 LAMP

NOTE: Make sure of the number of lamps that need to be replaced by referring to the Lamp Status Display and the Lamp Management Function.

Remove the two screws on the Sanyo PLC-XF40 Lamp Cover.
Press the top button to open the Lamp Cover.
Choose which lamp needs to be replaced. BE SURE TO PICK THE CORRECT LAMP THAT NEEDS TO BE REPLACED.
Loosen the two screws holding the Sanyo POA-LMP42 (service part no 610-292-4831) lamp in place.
Grasp the handle and gently pull out the defective Sanyo POA-LMP42 lamp. Place to one side. Be sure to dispose of the used Sanyo POA-LMP42 lamp through a local recycling program. Don’t throw this lamp into the regular garbage as it contains mercury.
Take the new Sanyo POA-LMP42 lamp by the handle and gently guide it into place.
Tighten the two screws holding the Sanyo POA-LMP42 (service part 6102924831) lamp assembly in place.
Replace the Sanyo PLC-XF40 Lamp Cover and tighten the two screws to put the lamp cover back in place.
Reset the Lamp Counter following the instructions below.

LAMP COUNTER RESET FOR SANYO PLC-XF40

Turn the Sanyo PLC-XF40 projector on.
Press the MENU buttons to open the ON-SCREEN MENU.
Press POINT LEFT/RIGHT button to get the red frame pointer to move to the SETTING menu icon.
Press POINT DOWN button to Lamp counter reset. Press SELECT.
Move the arrow to the replaced lamp number (Lamp 1, Lamp 2, Lamp 3 or Lamp 4). Press SELECT. BE SURE TO RESET THE CORRECT LAMPS
The message “Lamp replace counter Reset?” will be displayed with YES or NO underneath.
Move the pointer to YES. Press the SELECT button.
Move to the second confirmation box and select YES.

NOTE: BE SURE TO RESET THE CORRECT LAMP otherwise the lamp replace indicator will continue lighting YELLOW.

RESETTING THE SANYO POA-LMP42 (6102924831) LAMP MODE

You can set the lamp mode to use either four lamps or two lamps. Using 2 lamps will prolong the life of the projector lamps.

Tips to make your Sanyo POA-LMP42 lamps last longer

Extend the life of your newly installed Sanyo POA-LMP42 (service part no 610-292-4831) by following these helpful tips:

Wait at least five minutes before turning the Sanyo PLC-XF40 projector off.
Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP42 and prevent the Sanyo PLC-XF40 projectorfrom overheating.

Tagged with: authentic projector lamps, genuine lamps, genuine projector lamps, Lamp replacement, philips, Projector LAMP, replacement lamps, replacement projector lamps, Sanyo PLC-XF40 projector, Sanyo POA-LMP42 610 292 4831, service part no 610 292 4831

How to replace the lamps in your Sanyo PLC-UF10 projector

Shelagh McNallyPosted on March 30, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Sanyo PLC-UF10 projector

Your Sanyo PLC-UF10 projector is equipped with four Sanyo POA-LMP42 (service part 610-292-4831) projector lamps.

There is a Lamp Replace Indicator at the front and at the back of the projector. When any four of the projector lamps is nearing end of life, these indicators will flash yellow. In order to determine which of the four Sanyo POA-LMP42 (service part 6102924831) projector lamps needs to be replaced, you’ll need to consult the Lamp Status Display on the Sanyo PLC-UF10 projector screen.

Buy an authentic Sanyo POA-LMP42 (service part 6102924831) projector lamp and make life easier. Generic lamps look like a great bargain but these knock-off lamps are created with inferior materials making them susceptible to explosions when installed. They also have a shorter life span and can damage the precise components in your Sanyo PLC-UF10 projector. Learn more about spotting dangerous projector lamps by reading our article: 7 tips for spotting counterfeits.

LAMP STATUS DISPLAY SETTINGS

The Lamp Status Display shows the status of each lamp:

LAMP MANAGEMENT FUNCTION

The Lamp Management Function automatically changes the combinations of lighting lamps by detecting which lamps are still working.

When any of the four Sanyo POA-LMP42 lamps goes out, Lamp Mode will automatically switch from using four Sanyo POA-LMP42 (6102924831) lamps to using two lamps.

When any of the two Sanyo POA-LMP42 (service part no 610-292-4831) lamps are out, the projector will operate using only one lamp.

INSTALLING THE NEW SANYO POA-LMP42 LAMP

NOTE: Make sure of the number of lamps that need to be replaced by referring to the Lamp Status Display and the Lamp Management Function.

Remove the two screws on the Sanyo PLC-UF10 Lamp Cover and press the top button to open the Lamp Cover.
Choose which lamp needs to be replaced. BE SURE TO PICK THE CORRECT LAMP THAT NEEDS TO BE REPLACED.
Loosen the two screws holding the Sanyo POA-LMP42 (service part no 610-292-4831) lamp in place.
Grasp the handle and gently pull out the defective Sanyo POA-LMP42 lamp. Place to one side. Be sure to dispose of the used Sanyo POA-LMP42 lamp through a local recycling program. Don’t throw this lamp into the regular garbage as it contains mercury.
Take the new Sanyo POA-LMP42 lamp by the handle and gently guide it into place.
Tighten the two screws holding the Sanyo POA-LMP42 (service part 6102924831) lamp assembly in place.
Replace the Sanyo PLC-UF10 Lamp Cover and tighten the two screws to put the lamp cover back in place.
Reset the Lamp Counter following the instructions below.

LAMP COUNTER RESET FOR SANYO PLC-UF10

Turn the projector on
Press the MENU buttons to open the ON-SCREEN MENU.
Press POINT LEFT/RIGHT button to get the red frame pointer to move to the SETTING menu icon.
Press POINT DOWN button to Lamp counter reset. Press SELECT.
Move the arrow to the replaced lamp number (Lamp 1, Lamp 2, Lamp 3 or Lamp 4). Press SELECT. BE SURE TO RESET THE CORRECT LAMPS
The message “Lamp replace counter Reset?” will be displayed with YES or NO underneath.
Move the pointer to YES. Press the SELECT button.
Move to the second confirmation box and select YES.

NOTE: BE SURE TO RESET THE CORRECT LAMP otherwise the lamp replace indicator will continue lighting YELLOW.

RESETTING THE SANYO POA-LMP42 (6102924831) LAMP MODE

You can set the lamp mode to use either four lamps or two lamps. Using 2 lamps will prolong the life of the projector lamps.

Tips to make your Sanyo POA-LMP42 lamps last longer

Extend the life of your newly installed Sanyo POA-LMP42 (service part no 610-292-4831) by following these helpful tips:

Wait at least five minutes before turning the Sanyo PLC-XU10 projector off.
Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP42 and prevent the Sanyo PLC-XU10 projector from overheating.

Tagged with: authentic projector lamps, genuine projector lamps, POA-LMP42, Projector LAMP, replacement lamps, replacement projector lamps, Sanyo PLC-UF10 projector, Sanyo POA-LMP42

When to replace Sanyo POA-LMP99 projector lamp

Shelagh McNallyPosted on March 28, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Sanyo POA-LMP99

You can expect between 1,000 to 3,000 hours of use from the Sanyo POA-LMP99 if you’ve installed an authentic projector lamp. The exact amount of time will vary depending on how much your projector is used and how regularly the air filters are cleaned. (Clogged air filters cause the projector to heat up and this puts stress on the lamp.)

You won’t get as many hours if you’ve installed a knock-offs lamp since they have much shorter life spans due to their inferior workmanship and materials. Installing a generic projector lamp also voids the warranty on your projector. Walk away from lamps with a price tag that seems too good to be true. The few dollars you save are not worth, especially if the knock-off explodes inside your computer. Learn the 7 tips for spotting counterfeits lamps and protect yourself.

Eco-friendly alternative

Looking for a green alternative? Try replacing only the bulb and re-using the same plastic cage. Watch this Sanyo POA-LMP69 replacement guide to find out more.

Projectors compatible with the Sanyo POA-LMP99 projector lamp:

Scroll down for links to step-by-step instructions on replacing the Sanyo POA-LMP99 lamp for each of these projectors.

When it’s time to replace the Sanyo POA-LMP99 your projector’s Lamp Replacement Indicator will turn yellow. Be sure to buy an genuine projector lamp and get a lamp that keeps your projector working properly.

For step-by-step instructions on replacing your Sanyo POA-LMP99 lamp, click on your model listed below:

Sanyo PLC-XP40 projector

Click here for step-by-step instructionson how to change the Sanyo POA-LMP99 projector bulb for the Sanyo PLC-XP40 projector.

Sanyo PLC-XP45 projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP99 projector bulb for the Sanyo PLC-XP45 projector.

Sanyo PLV-70 projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP99 projector bulb for the Sanyo PLV-70 projector.

: Sanyo PLV-75 projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP99 projector bulb for the Sanyo PLV-75 projector.

Tagged with: authentic lamps, POA-LMP99, replacement projector lamps, Sanyo PLC-XP40. Sanyo PLC-XP45, Sanyo PLV-70, Sanyo PLV-75, Sanyo POA-LMP99

Lifespan of the Sanyo POA-LMP33

Shelagh McNallyPosted on March 28, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Sanyo POA-LMP38

You can expect between 1,000 to 3,000 hours of use from the SANYO POA-LMP38 (service part no 610 291 5868) if you’ve installed an authentic projector lamp. The exact amount of time will vary depending on how much your projector is used and how regularly the air filters are cleaned. (Clogged air filters cause the projector to heat up and this puts stress on the lamp.)

Projectors compatible with the SANYO POA-LMP38 (service part no 610 291 5868) projector lamp:

Sanyo PLC-XP40

Sanyo PLC-XP45

Sanyo PLV-70

Sanyo PLV-75

Scroll down for links to step-by-step instructions on replacing the SANYO POA-LMP38 (service part no 610 291 5868) lamp for each of these projectors.

When it’s time to replace the Sanyo POA-LMP38 your projector’s Lamp Replacement Indicator will turn yellow. Be sure to buy an genuine projector lamp and get a lamp that keeps your projector working properly.

For step-by-step instructions on replacing your SANYO POA-LMP38 (service part no 610 291 5868) lamp, click on your model listed below:

Sanyo PLC-XP40 projector

Click here for step-by-step instructions on how to change the SANYO POA-LMP38 (service part no 610 291 5868)projector bulb for the Sanyo PLC-XP40 projector.

Sanyo PLC-XP45 projector

Click here for step-by-step instructions on how to change the SANYO POA-LMP38 (service part no 610 291 5868) projector bulb for the Sanyo PLC-XP45 projector.

Sanyo PLV-70 projector

Click here for step-by-step instructions on how to change the SANYO POA-LMP38 (service part no 610 291 5868) projector bulb for the Sanyo PLV-70 projector.

Sanyo PLV-75 projector

Click here for step-by-step instructions on how to change the SANYO POA-LMP38 (service part no 610 291 5868) projector bulb for the Sanyo PLV-75 projector.

Tagged with: authentic lamps, authentic projector lamps, genuine lamps, genuine projector lamps, Lamp replacement, Projector LAMP, replacement lamps, replacement projector lamps, Sanyo PLC-XP40. Sanyo PLC-XP45, Sanyo PLV-70, Sanyo PLV-75, Sanyo POA-LMP38, SANYO POA-LMP38 (service part no 610 291 5868)