About Us - Page 3962 of 4063 - DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP

3 steps to a new Epson Powerlite 810P projector lamp

Shelagh McNallyPosted on March 4, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Follow this 3-step guide to replace Epson Powerlite 810P projector lamp

The Epson Powerlite 810P projector lampwill have 1500 hours of lamp life depending on usage.

Replacement signs

If regular maintenance is done on the Epson Powerlite 810P, the lamp will last longer. Watch for the warning signs that you need to replace the Epson Powerlite 810P projector lamp

Image begins to dim or actually deteriorate. Colours appear distorted.
“Replace the Lamp” warning message appears on screen.
Lamp light lights red or starts flashing red.

Check the amount of lamp life left from the About menu found on the Main Menu.

Buy authentic

When if comes to installing your Epson ELPLP15 it’s best to buy an authentic lamp from an OEM source. There are plenty of cheap lamps for sale. In fact, some of the more popular retail sites sell project lamps with major discounts. These “generic” lamps are advertised as compatible with your Epson PowerLite 810P when it fact they have a variety of problems:

prone to explosions because of their inferior workmanship
don’t last the full 1400 hours
present health hazard due to the toxic materials used
can damage the projector optics since they are not calibrated properly
copycat manufacturers offer no guarantee or refunds
the warranty on your Epson EMP-820 projector will become void.

Learn the 7 Ways to Spot a Counterfeit Lamp.

Step 3: Installing the new Epson ELPLP15 lamp

Before opening the Epson PowerLite 810P projector and installing the new Epson ELPLP15 lamp, do these preparatory steps:

Turn off the projector and wait until the power lights stops flashing.
Unplug the power cord so the projector can’t be accidentally turned of while the lamp is being replaced.
Wait for at least one hour for the Epson PowerLite 810P to cool down. It should be cool to the touch. This is crucial. These projectors operate under high heat and you can get burned very badly if the projector is still hot.

Take the screwdriver that came with the Epson PowerLite 810P and use it to pop open the lamp cover. Put the lamp cover to one side.

Once the lid is removed, use the same screwdriver to loosen the screws holding the Epson ELPLP15 in place. NOTE: The screws will not come all the way out.

Grab the top ridges along the Epson ELPLP15 lamp and gently pull up without using too much force. Learn how to clean up after a bulb breaks.

Put the old lamp aside for proper recycling. These lamps can’t be thrown into the garbage as they contain mercury.

Hold the lamp so it faces the correct way and insert the Epson ELPLP15 lamp until it clicks into place. Tighten the screws. Line up the hinges on the cover and snap back into place.

You are now ready to reset the lamp timer.

Resetting the Epson PowerLite 810P lamp timer

After replacing the Epson ELPLP15 lamp you’ll need to reset the lamp timer in order for the Epson PowerLite 810P to properly track the lamp life. Only reset the Epson PowerLite 810P lamp timer when a new Epson ELPLP15 lamp has been installed or you run the risk of the lamp being used beyond its recommended lamp life and damaging your projector.

To reset the lamp:

Press the MENU button on either projector’s control panel or on the remote control to display the MAIN MENU.
Scroll down to the ABOUT menu. Press the ENTER.
Scroll down to the Reset Lamp Timer option.
The reset dialogue box will appear asking you to Execute? Press Yes.
The lamp hours will be reset to zero.
No lamp hours will appear until you have used the Epson ELPLP15 for at least 10 hours.

Tips for longer lamp life:

Extend the life of the newly installed Epson ELPLP15 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson PowerLite 810P projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life.

Save

Tagged with: authentic lamps, authentic projector lamps, Epson ELPLP15 lamp, Epson Powerlite 810P projector

How to replace the Epson Powerlite 800P projector lamp

Shelagh McNallyPosted on March 4, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Follow this step-by-step guide to replace the Epson Powerlite 800P projector

Epson Powerlite 800P projector lamp should 1500 hours of lamp life.

Replacement signs

Watch for the warning signs that you need to replace the Epson Powerlite 800P projector lamp

Image begins to dim or actually deteriorate. Colours appear distorted.
“Replace the Lamp” warning message appears on screen.
Lamp light lights red or starts flashing red.
Track the hours on the lamp left on the About menu found on the Main Menu.

Buy authentic

Genuine Epson ELPLP15 lamp are the only lamps that will keep your Epson Powerlite 800P working at its optimum levels. These OEM authentic Epson ELPLP15 lamps have been manufactured to meet the specifications of the Epson Powerlite 800P projector.

Counterfeit lamps can damage the sensitive and expensive mechanisms in your Epson Powerlite 800P projector projector and actually have a much shorter lamp life. They are also more prone to explosions due to the inferior materials used during their production.

Look for the seal of approval and buy from an authentic manufacturer. Learn how to protect yourself from counterfeit manufacturers.

Installing the new Epson ELPLP15 lamp

Do these prepatory steps before opening the Epson PowerLite 800P projector and installing the new Epson ELPLP15 lamp:

Turn off the projector and wait until the power lights stops flashing.
Unplug the power cord so the projector can’t be accidentally turned of while the lamp is being replaced.
Wait for at least one hour for the Epson PowerLite 800P to cool down. These projectors operate under high heat and you can get burned very badly if the projector is still hot. Watch until the projector is cool to the touch.

Take the screwdriver that came with the Epson PowerLite 800P and use it to pop open the lamp cover. Put the lamp cover to one side.

Once the lid is removed, use the same screwdriver to loosen the screws holding the Epson ELPLP15 in place. NOTE: The screws will not come all the way out.

Grab the top ridges along the Epson ELPLP15 lamp and gently pull up without using too much force. Learn how to clean up after a bulb breaks.

NOTE: Put the old lamp aside for proper recycling. These lamps can’t be thrown into the garbage as they contain mercury.

Hold the lamp so it faces the correct way and insert the Epson ELPLP15 lamp until it clicks into place. Tighten the screws. Line up the hinges on the cover and snap back into place.

You are now ready to reset the lamp timer.

Resetting the lamp timer

Reset the Epson PowerLite 800P lamp timer when a new Epson ELPLP15 lamp has been installed so the projector can track the lamp life accurately, Failure to do so can result in the lamp being used beyond its recommended life and causing damage to your projector.

To reset the lamp timer:

Press the MENU button on either projector’s control panel or on the remote control to display the MAIN MENU.
Scroll down to the ABOUT menu. Press the ENTER.
Scroll down to the Reset Lamp Timer option.
The reset dialogue box will appear asking you to Execute? Press Yes.
The lamp hours will be reset to zero.
No lamp hours will appear until you have used the Epson ELPLP15 for at least 10 hours.

Tips for longer lamp life:

Extend the life of the newly installed Epson ELPLP15 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson PowerLite 800P projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life.

Save

Tagged with: authentic lamps, authentic projector lamps, Epson ELPLP15 lamp, Epson Powerlite 800P

Install a new Epson PowerLite 600P projector lamp

Shelagh McNallyPosted on March 3, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Follow this quick-step guide to install a new Epson PowerLite 600P projector lamp

Replacing the lamp in your Epson PowerLite 600P projector lamp is simple.

When is the lamp finished?

There are approximately 1500 hours in the typical Epson ELPLP15 lamp. If regular maintenance is done where the air filter is kept clean, the lamp will last longer. If the lamp is used longer than five hours per day this will shorten the Epson ELPLP15 lamp life.When it’s approaching end of life there will be some very distinct signs that the Epson Powerlite 600P projector needs a new lamp:

Dark image
Image begins to dim or actually deteriorate. Colours appear distorted.
“Replace the Lamp” warning message appears on screen
Lamp light lights red or starts flashing red

Check the amount of lamp life left from the About menu found on the Main Menu.

Installing the Epson PowerLite 600P projector lamp

Before opening the Epson PowerLite 600P projector and installing the new Epson ELPLP15 lamp, do these preparatory steps:

Turn off the projector and wait until the power lights stops flashing.
Unplug the power cord so the projector can’t be accidentally turned of while the lamp is being replaced.
Wait for at least one hour for the Epson PowerLite 600P to cool down. It should be cool to the touch. This is crucial. These projectors operate under high heat and you can get burned very badly if the projector is still hot.

Take the screwdriver that came with the Epson PowerLite 600P and use it to pop open the lamp cover. Put the lamp cover to one side.

Once the lid is removed, use the same screwdriver to loosen the screws holding the Epson ELPLP15 in place. NOTE: The screws will not come all the way out.

Grab the top ridges along the Epson ELPLP15 lamp and gently pull up. Using too much force can break the bulb. Learn how to clean up after a bulb breaks.

NOTE: Put the old lamp aside for proper recycling. These lamps can’t be thrown into the garbage as they contain mercury.

Hold the lamp so it faces the correct way and insert the Epson ELPLP15 lamp until it clicks into place. Tighten the screws. Line up the hinges on the cover and snap back into place.

You are now ready to reset the lamp timer.

Resetting the Epson PowerLite 600P lamp timer

After replacing the Epson ELPLP15 lamp you’ll need to reset the lamp timer in order for the Epson PowerLite 600P to properly track the lamp life. Only reset the Epson PowerLite 600P lamp timer when a new Epson ELPLP15 lamp has been installed or you run the risk of the lamp being used beyond its recommended lamp life and damaging your projector.

To reset the lamp:

Press the MENU button on either projector’s control panel or on the remote control to display the MAIN MENU.
Scroll down to the ABOUT menu. Press the ENTER.
Scroll down to the Reset Lamp Timer option.
The reset dialogue box will appear asking you to Execute? Press Yes.
The lamp hours will be reset to zero.
No lamp hours will appear until you have used the Epson ELPLP15 for at least 10 hours.

Why buy authentic lamps?

When if comes to installing your Epson ELPLP15 it’s best to buy an authentic lamp from an OEM source. There are plenty of cheap lamps for sale. In fact, some of the more popular retail sites sell project lamps with major discounts. These “generic” lamps are advertised as compatible with your Epson PowerLite 600P when it fact they can can damage the sensitive components and are prone to explosions.

Other problems with “generic, compatible” lamps include a have shorter lamp life while exposing you to toxic materials used to create the lamps. When you see the seal of approval you’ll know you are buying from an authentic manufacturerY who offers technical support plus money-back guarantee. Unlike generics, installing original OEM lamps won’t void your warranty.

Protect yourself from and installing generic lamps by reading the 7 Ways to spot a counterfeit lamp.

Tips for longer lamp life:

Extend the life of the newly installed Epson ELPLP15 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson PowerLite 600P projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life.

Save

Tagged with: authentic lamps, Epson ELPLP15 lamp, Epson PowerLite 600P, Epson projector lamps

Replace the Epson EMP-810UG projector lamp

Shelagh McNallyPosted on March 3, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — 1 Comment ↓

Learn how to replace the Epson EMP-810UG projector lamp with this installation guide

Your Epson EMP-810UG projector will not work without a proper lamp installed. It needs an authentic Epson EMP-810UG projector lamp installed.

OEM lamps to protect your projector

Keep your Epson EMP-810UG projector in good working condition by installing a genuine Epson ELPLP15 lamp. These OEM Epson ELPLP15 lamps have been manufactured to meet the specifications of a Epson EMP-810UG projector.

Knock-off lamps, also known as generic or compatible lamps, may seem like a bargain due to their low prices but they can damage the sensitive and expensive mechanisms in your Epson EMP-810UG projector projector as well as expose you to carcinogenic materials.

Keep your warranty in good shape, get support and money-back guarantee when you buy authentic. Learn the 7 Ways to spot a counterfeit lamp.

Warning signs for replacing

The Epson ELPLP15 has an expected life of 1400 hours but this time may vary depending on how often the Epson EMP-810UG projector is used. Regular maintenance left undone, such as cleaning out the air filters, also shortens the lamp life.

Know the warning signs that the lamp is approaching end of life:

The lamp indicator flashes orange or lights red.
The message “Lamp Replace” appears on the screen for 30 seconds when the projection starts.
The user’s logo disappears on screen and the lamp replacement message appears instead.
The colour gets less clear and images gets darker or grow dimmer.

Installing a new Epson ELPLP15 lamp

Do these steps before installing the new lamp:

Turn off the projector power and wait for the cool-down period which is about two minutes. Disconnect the power cord after the two minutes are over.
Wait at least 30 minutes to one hour for the Epson EMP-810UG projector to cool internally before opening it up. It should be cool to the touch.
Do not operate the projectors while the lamp is removed as this may result in malfunctions, fire hazard and other accidents.

Use the screwdriver provided and place it into the slot so the Epson EMP-810UG lamp cover lifts up. Hold the raised section of the lamp cover to slide it forward and remove it from the projector.

Using the same screwdriver, loosen the two screw holding the Epson ELPLP15 lamp in place.

Grab the Epson ELPLP15 by its two sides taking care not to knock the actual bulb — this can cause it to break. sides of the lamp and pull from the projector. Take care not knock the actual bulb as it may break. Learn what to do if the bulb breaks.

NOTE: The Epson ELPLP15 lamp contains mercury and needs to be properly recycled. Because it contains mercury, it can’t be thrown into the regular day-to-day garbage.

Hold the lamp so it faces the correct way and insert the Epson ELPLP15 lamp until it clicks into place. Tighten the screws.

To re-install the lamp cover, align the top tabs with the Epson EMP-810UG projector. Press the other side of the cover until it clicks into place.

A spare air filters comes with this lamp and should be replaced at the same. You must now reset the lamp timer.

Resetting the Epson EMP-810UG lamp timer

After replacing theEpson ELPLP15 lamp you’ll need to reset the lamp timer in order for the Epson EMP-810UG to properly track the lamp life. Only reset the Epson EMP-810UG lamp timer when a new Epson ELPLP15 lamp has been installed or you run the risk of the lamp being used beyond its recommended lamp life and damaging your projector.

To reset the lamp:

Press the MENU button on either projector’s control panel or on the remote control.
The MAIN MENU will be shown.
Using the arrow keys scroll to Reset Lamp Timer from the ABOUT menu.
Press the ENTER key.

A second prompt screen will be displayed.

Select YES to EXECUTE.
Press the ENTER button.
The lamp hours will be rest to zero

How to extend the life of the Epson ELPLP15 lamp:

Extend the life of the newly installed Epson ELPLP15 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson EMP-810UG projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Set the Brightness Mode to low or Econo Mode to extend lamp life.
Learn more with Top tips for extending DLP projector lamp life.

Save

Tagged with: authentic lamps, authentic projector lamps, Epson ELPLP15 lamp, Epson EMP-810UG, Epson projector lamps

Replacing the Epson EMP-820P projector lamp

Shelagh McNallyPosted on March 3, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Follow this guide to replace the Epson EMP-820P projector lamp

The Epson EMP-820P projector lamp has an expected life of 1500 hours.

When to replace

Have an extra lamp on hand since some lamps may stop before 1400 hours depending on the usage and amount maintenance performed. (See extending your lamp life below)

The warning signs:

The lamp indicator flashes orange or lights red.
The message “Lamp Replace” appears on the screen for 30 seconds when the projection starts.
The user’s logo disappears on screen and the lamp replacement message appears instead.
The images gets darker or starts to deteriorate

Using the correct lamp

Protect your investment and buy genuine Epson ELPLP15 lamps for your Epson EMP-820P projector. OEM authentic Epson ELPLP15 lamps have been manufactured to meet the specifications of your projector and will keep it working at optimum levels.

Beware of the generics being sold over the Internet! These lamps can damage the sensitive and expensive mechanisms and are also prone to explosions. They have been created with Krypton-85 and other toxic materials that put your health at risk. Installing a knock-off lamp will also void the guarantee on your Epson EMP-820P projector leaving you unprotected should anything happen after installation. Avoid hassles and buy authentic. Look for the seal of approval and buy from an authentic manufacturer. Learn how to protect yourself from counterfeit manufacturers.

Installing a new Epson ELPLP15 lamp

Pre-installation preparations:

1. Turn off the power to the Epson EMP-820P projector. Wait for a two-minute cool down period — the projector may beep when it’s reached the time limit.

2. Disconnect the power cord after the two minutes is over.

3. Wait an additional 45 minutes to one hour for the Epson EMP-820P projector to cool internally before opening it up. Wait the full period as these projectors operate under high temperature and you can burn yourself badly.

NOTE: Do not operate the projectors while the lamp is removed as this may result in malfunctions, fire hazard and other accidents.

To install:

Use the screwdriver provided and place it into the slot so the Epson EMP-820P lamp cover lifts up. Hold the raised section of the lamp cover to slide it forward and remove it from the Epson EMP-820P projector.

Loosen the two screw holding the Epson ELPLP15 lamp in place.

Grab the sides of the Epson ELPLP15 lamp and gently pull from the projector taking care not to knock the bulb as it may break. Learn what to do should the bulb shatter.

NOTE: Don’t throw this Epson ELPLP15 into standard garbage. Since it contains mercury it must be properly recycled.

Hold the lamp so it faces the correct way and insert the Epson ELPLP15 lamp until it clicks into place. Tighten the screws.

Insert the cover tabs into the Epson EMP-820P projector. Press the other side of the cover until it clicks into place. You are ready to reset the lamp timer.

Resetting the Epson EMP-820P lamp timer

After replacing the Epson ELPLP15, you will need to reset the timer in the Epson EMP-820P so the projector can properly track the lamp life. Only reset the Epson EMP-820P lamp timer when a new Epson ELPLP15 lamp has been installed. Otherwise, the projector will NOT know when it’s time to replace the lamp. You run the risk of damaging your projector.

Press the MENU button on either projector’s control panel or on the remote control.
The MAIN MENU will be shown.
Using the arrow keys scroll to Reset Lamp Timer from the ABOUT menu.
Press the ENTER key.
A second prompt screen will be displayed.
Select YES to EXECUTE.
Press the ENTER button.
The lamp hours will be rest to zero.

Extend the life of the Epson ELPLP15 lamp:

Extend the life of the newly installed Epson ELPLP15 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson EMP-820P projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Set the Brightness Mode to low or Econo Mode to extend lamp life.
Learn more with Top tips for extending DLP projector lamp life.

Save

Tagged with: authentic projector lamps, Epson ELPLP15, Epson ELPLP15 lamp, Epson EMP-820P projector

Replacement instructions for your Epson EMP-800UG projector lamp

Shelagh McNallyPosted on March 1, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

You can install a new Epson EMP-800UG projector lamp in three easy steps.

You can expect up to 1400 of Epson EMP-800UG projector lamp life depending on usage and whether regular maintenance is done.

Step 1: Watch for warning signs

The Epson EMP-800UG projector uses the Epson ELPLP15 lamp. Keep an extra Epson ELPLP15 on hand and watch for warning signs that the lamp is approaching end of life.

The lamp indicator on the projector flashes orange or lights up red.
The message “Lamp Replace” appears on screen seconds when the projection starts.
The colour and image starts to deteriorate becoming dark or dim.

Step 2: Be prepared with the correct lamp

Your Epson EMP-800UG has been built to operate with an OEM manufactured lamp that is properly calibrated to work with the highly sophisticated optics in the projector. Buying genuine Epson ELPLP15 lamps that have been manufactured to meet the needs of the Epson EMP-800UG will guarantee a longer life for the projector.

Why avoid generic lamps?

Generic lamps may appear like an incredible bargain due to their price tag. But when you factor in all the problems they cause, generic lamps actually cost more in the long run. Here’s a list of their associated problems:

prone to explosions because of their inferior workmanship
don’t last the full 1400 hours
health hazard due to the toxic materials used
not calibrated properly and will damage the optics
copycat manufacturers offer no guarantee or refunds
the warranty on your Epson EMP-800UG projector will become void.

Protect your health, the health of your Epson EMP-800UG projector and buy authentic. Don’t be fooled by the generic manufacturers: Learn the 7 Ways to Spot a Counterfeit Lamp.

Step 3: Installing the new Epson ELPLP15 lamp

Getting ready:

Turn off the projector power and give a two-minute cool-down period before disconnecting the power cord.
Give the Epson EMP-800UG projector enough time to cool down — wait at least 30 minutes to one hour. These projector operates under high heat. Be sure it’s cool the the touch before opening it up.
Do not operate the projectors while the lamp. It can ruin the projector beyond repair as well as result in a fire and other accidents.

Place the screwdriver provided into the slot on the lamp cover. Lift it up and slide off the lamps cover on the Epson EMP-800UG lamp cover until the hinges release. Place the cover to one side.

Loosen the two screw holding the Epson ELPLP15 lamp in place.

Grab lamp by it side and pull straight up from the projector. Take care not knock the actual bulb as it may break. Learn what to do should the bulb shatter.

NOTE: Don’t throw this lamp into the regular garbage! The Epson ELPLP15 lamp contains mercury and must be properly recycled.

Hold the lamp by the sides. Don’t touch the actual glass bulb as your fingerprints will leave marks that will gradually cause a black dot on the screen when the projector heats ups. Facing the Epson ELPLP15lamp the correct way so it fits into the projector, gently lower it into the projector. Tighten the screws.

Insert the cover tabs into the Epson EMP-800UG projector, making sure they line up properly with the tabs. Press the other side of the cover down until it clicks into place.

Be sure the lamp cover is on properly or the projector will not turn on.

You are now ready to reset the lamp timer.

Resetting the Epson EMP-800UG lamp timer

After installing a new Epson ELPLP15 lamp, the lamp timer will need to be reset in order for the Epson EMP-800UG to properly track the lamp life. You run the risk of damaging your projector should the lamp be used beyond the recommended 1900 hours, so only reset the lamp hours when a new lamp has been installed.

Press the MENU button on either projector’s control panel or on the remote control.
The MAIN MENU will be shown.
Using the arrow keys scroll to Reset Lamp Timer from the ABOUT menu.
Press the ENTER key.

A second prompt screen will be displayed.

Select YES to EXECUTE.
Press the ENTER button.
The lamp hours will be rest to zero.

Extend the life of the Epson ELPLP15 lamp:

Extend the life of the newly installed Epson ELPLP15 with the following tips:

Set the Brightness Mode to low or Econo Mode to extend lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Keep your air filters clean to avoid overheating the projector.
Turn off the Epson EMP-800UG and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Learn more with Top tips for extending DLP projector lamp life.

Save

Tagged with: authentic lamps, Epson ELPLP15 lamp, Epson EMP-800UG projector, Epson projector lamps

Replacing the Epson EMP-811P projector lamp

Shelagh McNallyPosted on February 28, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

For a quick and easy replacement of the Epson EMP-811P projector lamp

Follow this step-by-step guide to replace the Epson EMP-811P projector lamp.

Lamp Life & Warning Signs

The Epson ELPLP15 has an expected life of 1500 hours. Keep an extra lamp on hand since lamp life will vary. Heavy use of the Epson EMP-811P projector will reduce the expected hours.

Watch for the warning signs:

The lamp indicator flashes orange/red.
The message “Lamp Replace” appears on the screen for 30 seconds when the projection starts.
The user’s logo disappears on screen and the lamp replacement message appears instead.
The images gets darker or starts to deteriorate
Have an extra lamp on hand since some lamps may stop before 1500 hours.

Go with authentic

Buyer Beware of generic lamps bought over the Internet. Before purchasing your Epson ELPLP15 lamp look for the OEM seal of approval.

This seal guarantees that the lamp you are about to buy has been been manufactured to meet the specifications of the Epson EMP-811P projector and will keep it working under optimum conditions.

Generic lamps, advertised as “compatible” are created with toxic, carcinogenic materials and despite their bargain prices, actually cost more in the long run because they have a shorter life. Generics can also can damage the sensitive and expensive mechanisms in your Epson EMP-811P projector projector.

Avoid having your warranty become void and other hassles by only buying authentic Epson ELPLP15 lamps. Don’t be fooled — learn how to otect yourself from counterfeit manufacturers.

How to install the new Epson ELPLP15 lamp

Before installing the lamp get the Epson EMP811P projector ready:

Turn off the projector power.
Give two-minutes for a cool-down period and then disconnect the power cord.
Wait at least 30 minutes to one hour for the Epson EMP-811P projector to cool internally before opening it up. It should be cool to the touch.
NOTE: Do not operate the projectors while the lamp is removed as this may result in malfunctions, fire hazard and other accidents.

To install:

Using the screwdriver provided, place it into the slot on the cover and lift up the Epson EMP-811P lamp cover. Slide the lamp cover tforward and remove it from the Epson EMP-811P projector.

Using the same screwdriver, loosen the screws holding the Epson ELPLP15 lamp in place.

Grabbing the two indents on the sides of the Epson ELPLP15 lamp, pull straight up. Take care not knock the actual bulb as it may break. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP15 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

Hold the lamp so it faces the correct way and insert the Epson ELPLP15 lamp until it clicks into place. Tighten the screws. Be sure not to touch the actual glass bulb as the oil from your fingers will cause a black spot to appear when the lamp heats up.

Insert the cover tabs into the Epson EMP-811P projector. Press the other side of the cover until it clicks into place. You are ready to reset the lamp timer.

Resetting the Epson EMP-600P lamp timer

The lamp timer will need to be reset after replacing the Epson ELPLP15. Only reset the Epson EMP-811P lamp timer when a new Epson ELPLP15 lamp has been installed, otherwise the projector will NOT know when it’s time to replace the lamp. You run the risk of damaging your projector.

Press the MENU button on either projector’s control panel or on the remote control.
The MAIN MENU will be shown.
Using the arrow keys scroll to Reset Lamp Timer from the ABOUT menu.
Press the ENTER key.

A second prompt screen will be displayed.
Select YES to EXECUTE.
Press the ENTER button.
The lamp hours will be rest to zero.

Extend the life of the Epson ELPLP15 lamp:

Extend the life of the newly installed Epson ELPLP15 with the following tips:

Make sure there is enough airflow around the pson EMP-811Pprojector particularly if it’s been permanently mounted.
Keep your air filters clean to avoid overheating the projector.
Set the Brightness Mode to low or Econo Mode to extend lamp life.
Turn off the Epson EMP-811P projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Learn more with Top tips for extending DLP projector lamp life.

Save

Tagged with: authentic lamps, Epson ELPLP15 lamp, Epson projector lamps

Your D.I.Y. guide to a new Epson EMP-820 projector lamp

Shelagh McNallyPosted on February 28, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Follow this D.I.Y. guide for replacing the Epson EMP-820 projector lamp

It’s just three quick and easy steps to replace Epson EMP-820 projector lamp.

Step 1: Watch for warning signs

The Epson ELPLP15 has an expected life of 1400 hours but this may vary depending how much the Epson EMP-820 is used. Keep an extra Epson ELPLP15 on hand to be ready the lamp should any of the warning signs appear.

Watch for the warning signs:

The lamp indicator on the projector flashes orange or lights up red.
The message “Lamp Replace” appears on the screen for 30 seconds when the projection starts.
The user’s logo is replaced by the lamp replacement message appears instead.
The colour starts to deteriorate or the image gets dark and dim.

Step 2: Be ready with the correct lamp

Your Epson EMP-820 is equipped with highly sensitive optics. You’ll want to keep them working at their optimum levels and not incur expensive repair bills. Buying genuine Epson ELPLP15 lamps that have been manufactured to meet the needs of the Epson EMP-820 will guarantee a long life for the projector.

Why avoid generic lamps?

Buyer Beware of generic lamps:

generic lamps are prone to explosions because of their inferior workmanship
generic lamps won’t last the full 1400 hours
they are a health hazard because they have been created with toxic materials
generic lamps are not calibrated properly and will damage the optics
copycat manufacturers offer no guarantee or refunds
the warranty on your Epson EMP-820 projector will become void.

Learn how to spot the copycat fake lamps with 7 Ways to Spot a Counterfeit Lamp.

Step 3: Installing a new Epson ELPLP15 lamp

Before installation:

Turn off the projector power and give a two-minute cool-down period before disconnecting the power cord.
Give the Epson EMP-820 projector enough time to cool down — wait at least 30 minutes to one hour. These projector operates under high heat. Be sure it’s cool the the touch before opening it up.
Do not operate the projectors while the lamp is removed as this may result in malfunctions, fire hazard and other accidents.

Place the screwdriver provided into the slot on the lamp cover. Lift it up and slide off the lamps cover on the Epson EMP-820 lamp cover until the hinges release. Place the cover to one side. Loosen the two screw holding the Epson ELPLP15 lamp in place.

Grab lamp by it side and pull straight up from the projector. Take care not knock the actual bulb as it may break. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP15 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

Hold the lamp so it faces the correct way and insert the Epson ELPLP15 lamp until it clicks into place. Don’t touch the actual glass bulb as your fingerprints will leave marks that will gradually cause a black dot on the screen when the projector heats ups. Tighten the screws.

Insert the cover tabs into the Epson EMP-820 projector, making sure they line up properly with the tabs. Press the other side of the cover down until it clicks into place.

Be sure the lamp cover is on properly or the projector will not turn on.

You are now ready to reset the lamp timer.

Resetting the Epson EMP-820 lamp timer

After installing a new Epson ELPLP15 lamp, the lamp timer will need to be reset in order for the Epson EMP-820 to properly track the lamp life. You run the risk of damaging your projector should the lamp be used beyond the recommended 1900 hours, so only reset the lamp hours when a new lamp has been installed.

Press the MENU button on either projector’s control panel or on the remote control.
The MAIN MENU will be shown.
Using the arrow keys scroll to Reset Lamp Timer from the ABOUT menu.
Press the ENTER key.

A second prompt screen will be displayed.
Select YES to EXECUTE.
Press the ENTER button.
The lamp hours will be rest to zero.

Extend the life of the Epson ELPLP15 lamp

Extend the life of the newly installed Epson ELPLP15 with the following tips:

Set the Brightness Mode to low or Econo Mode to extend lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Keep your air filters clean to avoid overheating the projector.
Turn off the Epson EMP-820 and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Learn more with Top tips for extending DLP projector lamp life.

Save

Tagged with: authentic lamps, Epson ELPLP15 lamp, Epson EMP-820

3 Steps to a new Epson EMP-811 projector lamp

Shelagh McNallyPosted on February 27, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Follow this quick step guide to replacing your Epson EMP-811 projector lamp in three easy steps.

Know when the Epson EMP-811 projector lamp needs to be replaced. The Epson EMP-811 projector uses the Epson ELPLP15 projector lamp.

Step 1: Be prepared

Your projector won’t work without a working lamp so it’s important to know when to replace the Epson EMP-811 projector lamp. Protect your projector by installing an original OEM lamp and by avoiding any generic or “compatible” lamps. Only genuine Epson ELPLP15 lamps have been manufactured to meet the specifications of the Epson EMP-811 projector.

Despite their bargain prices, knock-off lamps have a shorter life and can damage the sensitive mechanisms in your Epson EMP-811 projector projector. They are also prone to explosions and actually have a much shorter working life that authentic lamps due to the inferior materials used during their production. Even more troubling are the toxic, carcinogenic materials used to create these copycat lamps. you are being exposed to after installing one of these generic lamps.

Avoid hassles and buy authentic. Learn 7 Ways to spot a counterfeit lamp.

Step 2: Know when to replace

The Epson ELPLP15 has an expected life of 1400 hours. You may have less lamp life left if your Epson EMP-811 projector will reduce the expected hours. Watch for the warning signs:

The lamp indicator flashes orange or lights red.
The message “Lamp Replace” appears on the screen for 30 seconds when the projection starts.
The user’s logo disappears on screen and the lamp replacement message appears instead.
The images gets darker or starts to deteriorate
Have an extra lamp on hand since some lamps may stop before 1400 hours.

Installing a new Epson ELPLP15 lamp

Before installation:

Turn off the projector power. Let it cool for down for two minutes before removing the power cord.
Wait another 45 minutes to one hour for the Epson EMP-811 projector to cool internally before opening it up. It should be cool to the touch. This projector operates under high temperatures and you can burn yourself badly if you don’t wait until it has cooled.
Do not operate the projectors while the lamp is removed as this may result in malfunctions, fire hazard and other accidents.

Use the screwdriver provided and place it into the slot so the Epson EMP-811 lamp cover lifts up. Hold the raised section of the lamp cover to slide it forward and remove it from the Epson EMP-811 projector.

Loosen the two screw holding the Epson ELPLP15 lamp in place.

Grab the two indents on the other sides of the lamp and pull from the projector. Take care not knock the actual bulb as it may break. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP15 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

Hold the lamp so it faces the correct way and insert the Epson ELPLP15 lamp until it clicks into place. Tighten the screws.

Insert the cover tabs into the Epson EMP-811 projector. Press the other side of the cover until it clicks into place.

You are now ready to reset the lamp timer.

Resetting the Epson EMP-811 lamp timer

After replacing theEpson ELPLP15 lamp you’ll need to reset the lamp timer in order for the Epson EMP-811 to properly track the lamp life. Only reset the Epson EMP-811 lamp timer when a new Epson ELPLP15 lamp has been installed, otherwise the projector will NOT know when it’s time to replace the lamp.

To start press the menu button of either the remote control or on the Epson EMP-811 front panel in order to activate the Main Menu.

The MAIN MENU will be shown.
Using the arrow keys scroll to Reset Lamp Timer from the ABOUT menu.
Press the ENTER key.

A second prompt screen will be displayed.
Select YES to EXECUTE.
Press the ENTER button.
The lamp hours will be rest to zero.

How to extend the life of the Epson ELPLP15 lamp:

Extend the life of the newly installed Epson ELPLP15 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson EMP-811 projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Set the Brightness Mode to low or Econo Mode to extend lamp life.
Learn more with Top tips for extending DLP projector lamp life.

Save

Tagged with: authentic lamps, Epson ELPLP15, Epson EMP-811 projector

Compatible projectors with the Epson ELPLP34 lamp

Shelagh McNallyPosted on February 25, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Which projectors are compatible with the Epson ELPLP34 lamp

There are approximately 3000 hours in the typical Epson ELPLP34 lamp. Look for the seal of approval when you buy from an authentic manufacturer. Save yourself unnecessary headaches and avoid generic lamps.

When you buy authentic you’ll be getting a far superior product with a replacement guarantee and tech support.

6 reasons to buy authentic and avoid generics

OEM lamps have a longer life than generics
knock off lamps are created with toxic materials and pose a health threat
authentic lamps are safer and less likely to explode
copycat lamps can damage the sensitive electronics in your projectors
generics don’t come with a guarantee or tech support. Getting a refund can be a hassle.
your warranty on the Epson will be void if you install a generic lamp.

Protect yourself from tricked into purchasing counterfeit “generic-compatible” lamps.

When to replace the Epson ELPLP34 lamp

When it’s approaching end of life there will be some very distinct signs that the Epson needs a new lamp. Watch for the following telltale signs:

Dark image
Image that has deteriorated
“Replace the Lamp” warning message appears on screen
Lamp light flashes orange

Compatible projectors with the Epson ELPLP34 lamp

The Epson ELPLP34 lamp can be used with the following projectors:

Epson EMP-62, Epson EMP-82, Epson EMP-X3, Epson PowerLite 62C, Epson PowerLite 76c. Epson PowerLite 82c.

For step-by-step instructions on replacing your Epson ELPLP34 lamp, click on your projector listed below:

Click here for step-by-step instructions on how to change the Epson ELPLP34 projector lamp for the Epson EMP-62 projector.

Click here for step-by-step instructions on how to change the Epson ELPLP34 projector lamp for the Epson EMP-82 projector.

Click here for step-by-step instructions on how to change the Epson ELPLP34 projector lamp for the Epson EMP-X3 projector.

Click here for step-by-step instructions on how to change the Epson ELPLP34 projector lamp for the Epson PowerLite 62C projector.

Click here for step-by-step instructions on how to change the Epson ELPLP34 projector lamp for the Epson PowerLite 76c projector.

Click here for step-by-step instructions on how to change the Epson ELPLP34 projector lamp for the Epson PowerLite 82c projector.

Extend the life of the newly installed Epson ELPLP34 with the following tips:

Blocked air filters can cause your projector to overheat and shorten the lamp life.
Turning off the Epson projector for at least one hour per day and limiting use to 5 hours of daily usage will prolong lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted. The projector overheating can shorten the lamp life.
Learn more with Top tips for extending DLP projector lamp life.

Save

Tagged with: authentic lamps, authentic projector lamps, Epson ELPLP34, Epson EMP-62, Epson EMP-82, Epson EMP-X3, Epson PowerLite 62C, Epson PowerLite 76c, Epson PowerLite 82c