We're now Screen and Projector! For updated content, visit ScreenAndProjector.com and follow @screenandproj on social media!
Home › About Us › Page 80

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Epson_PowerLite_7850NL_Epson_ELPLP_22EPSON_ELPLP22_PROJECTOR_LAMPHere is your guide for a hassle-free installation of a new Epson EMP 7850 projector lamp.

Be sure to invest in an authentic Epson EMP 7850 projector lamp.

End of life warning signs

You can expect between 2000 to 3000 hours of lamp life before you must install a replacement. Set the brightness to low to get the maximum hours and be sure to keep your filters cleaned.

Warning signs that the Epson EMP 7850 projector lamp is reaching end of life include:

  • image getting darker or starting to deteriorates.
  • colours look off.
  • LAMP REPLACE messages appears on screen.
  • warning light flashing orange. When the lamp light is flashing RED, the Epson EMP 7850 projector lamp is burnt out and must be replaced immediately.

Why buy authentic?

There are many copy cat manufacturers selling knock-off Epson EMP 7850 projector lamp. Despite their bargain prices, these generic lamps end up costing you more because of their inferior workmanship. They can seriously damaged the optics in your Epson EMP 7850 since they have not been calibrated properly. Generic, compatible lamps also don’t last the full 2000 hours. Even more troublesome is the health hazard they pose due to the toxic materials.

Avoid all these problems and keep the warranty on your Epson Powerlite 7850 projector valid (using generic automatically voids your warranty). Don’t be fooled by the generic manufacturers. Learn the 7 Ways to Spot a Counterfeit Lamp and look for the seal of approval.

Installing the Epson EMP 7850 projector lamp

Bu sure to buy the Epson ELPLP22 model lamp. Then follow these important steps before installing the lamp:

  • Turn off the projector power.
  • When the power light stops flashing unplug the power cord.
  • Wait at least 60 minutes for the Epson EMP 7850 projector to cool internally before opening it up. It should be cool to the touch. These projectors operate under extremely high temperatures so be patient and wait until the projector is cool or you run the risk of burning yourself.

NOTE: Do not operate the projectors while the lamp is removed as this may result in malfunctions, fire hazard and other accidents.

Epson_EMP_7850_Epson_ELPLP_22_replace_air_filters

 

The Epson ELPLP22 lamp comes with a replacement air filter so you should change the filter at the same time. To change filters: turn the Epson EMP 7850 projector over and remove the air filters at the side and bottom of the projector. Replace the new filters — they should pop into place smoothly.

 

 

Epson_EMP_7850p_Epson_ELPLP_22_remove_lamp_cover

Insert the screwdriver supplied with the new Epson ELPLP22 lamp or use a flat-tipped screwdriver. Place the tip of the screwdriver into the space beside the air vent on the Epson EMP 7850 and gently slide the lamp cover to align the arrow on the cover with the arrow on the projector.

 

 

Epson_EMP_7850_loosen_screws_Epson_ELPLP_22

 

Loosen the two screws holding the Epson ELPLP22 lamp in place (they will not come all the way out). NOTE: The Epson ELPLP22 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps! If you bought from an authentic manufacturer they will recycle the lamp for you at no extra cost (another reason to buy authentic lamps).

 

 

 

Epson_EMP_7850_Epson_ELPLP_22_remove_lamp

Lift up the wire handle on the Epson ELPLP22 lamp and use it to pull the lamp straight out of the projector. Gently insert the new Epson ELPLP22 lamp. Avoid touching the actual bulb as the oil from your fingers will leave marks that will show up on screen. Also avoid knocking bulb as it may break. Learn what to do should the bulb shatter.

Tighten the screws and replace the lamp cover. NOTE: The projector will not turn on if the lamp cover is loose. You are now ready to reset the lamp timer.

Resetting the Epson EMP 7850 lamp timer

The lamp timer will track the life of the Epson ELPLP22 lamp and trigger the lamp warning messages. Therefore, it’s critical to reset the lamp timer whenever you replace the lamp in the Epson EMP 7850 projector. Do not re-set the Epson ELPLP22 lamp timer with an already used lamp as this may cause it to be used beyond its designated lamp life and cause an explosion.

 

Epson_EMP_7850_Epson_ELPLP_22_reset_lamp_timer

  • Plug the projector in and turn it on.
  • Press the MENU button on the remote or on the projector’s control panel to display the Main menu,
  • Use the pointer buttons on the remote or the arrow buttons on the Epson PowerLite 7850 to scroll down to the ABOUT menu. Press ENTER to display the ABOUT screen information.
  • Scroll down to RESET LAMP TIMER option.
  • Press ENTER to open the second prompt screen.

 

Epson_EMP_7850_Epson_ELPLP_22_reset_lamp_timer_screen2

Select YES and press ENTER.

  • The lamp hours will be reset to zero.
  • NOTE: Lamp usage appears as 0H until you’ve used at least 10 hours of lamp life
  • Press ESC or MENU to exit this screen.

 

How to extend the life of the Epson ELPLP22 lamp:

Extend the life of the newly installed Epson ELPLP22 with the following tips:

  • Keep your air filters clean to avoid overheating the projector.
  • Turn off the Epson EMP 7850 projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
  • Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
  • Set the Brightness Mode to low to extend lamp life.
  • Learn more with Top tips for extending DLP projector lamp life.
Tagged with: , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, LCD and Plasma TV Articles, Rear Projection TV Lamp Replacement — No Comments ↓

RUNTK5261TPZC -Vizio E601i-A4 70"

Troubleshooting guide for the Vizio E601i-A4 LED TV

That black screen on your Vizio E601i-A4 LED TV may be caused by a faulty T-Con board.There is nothing more disappointing than settling down to watch a favorite show  and discover your TV is not working.

Some of the VIZIO’s E601i-A4 LED TVs are experiencing blackouts after being turned on. The problem is a 8 pin eprom chip failure on the lower right side of the RUNTK5261TPZC timing control board (T-Con) that interrupts the video signal to the Main board.

This T-Con board failure is happening at 500 hours of usage. If your VIZIO E601i-A4 is older than a year, your warranty will not cover the replacement costs for a new T-Con board. Fortunately the replacement RUNTK5261TPZC T-Con board is available for sale online for under $150.

Replace the Vizio E601i-A4 LED TV T-Con board

Equipment needed:

  • Antistatic plastic gloves or antistatic bracelet
  • Pad/ towel
  • Needle-nose pliers
  • Electric Flat head and Philips screwdriver
  • Cup for screws

Step-by-step instructions

RUNTK5261TPZC -Vizio E601i-A4 70"

  • Turn the VIZIO’s E601i-A4 television off. Unplug the power cord.
  • Remove the TV from the wall, if mounted.
  • Lay the VIZIO’s E601i-A4 TV on a flat, padded surface.
  • Remove the TV stand by loosening the screws at the base. Both the stand and post must be removed in order to remove the back panel.
  • Go to the back of the panel.
  • Remove all the screws holding the back panel in place. Put the screws to one side.
  • Remove the back panel.
  • The RUNTK5261TPZC T-Con board is located in the middle top of the back panel, usually under an aluminum cover held in place by four corner screws. It may also be held in place with foil tape at the top. It’s connected to the Main board through a black LVDS cable and flat ribbon cables.
  • Remove the ribbon cable first. Flip up the black tabs on the connector. Gently pull the cable out taking care not the scratch the ribbon section. Never use any sharp objects to open the black tabs as this can damage the pins making the connection faulty.
  • To remove the LVDS cable, squeeze the small tab on side. Don’t force anything apart or pull anything too hard as this can damage the connections and cause more problems.
  • Loosen the screws holding the RUNTK5261TPZC T-Con board in place. Place it to one side. This board is considered e-waste and should be sent to a recycling facility. Do not place into regular garbage.
  • NOTE: Be sure to put on your rubber gloves before touching the new RUNTK5261TPZC T-Con board. Hold the board by the edge and avoid touching any of the components since they are very sensitive to electrostatic charges.
  • Verify the manufacturers number for your board. (It will be found under the bar code.) Place the new board onto the back panel.
  • To re-install the ribbon cable: Match the line on the ribbon cable with the edge of the connector making sure the ribbon is straight. Press down on the tab to lock it into place.
  • Re-connect the LVDS cable by putting the connector end into the RUNTK5261TPZC T-Con board until it clicks into place.
  • Tighten the screws on the board. Replace any foil tape.
  • Replace the RUNTK5261TPZC T-Con cover. Tighten the screws.
  • Place the back cover back onto the VIZIO’s E601i-A4 TV and tighten all the screws.
  • Re-install the stand and post. Remount the VIZIO’s E601i-A4 TV.

 

Alternative part numbers

The RUNTK5261TPZC T-Con board is also sold under the following numbers:

Tagged with: , , , , , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Epson_EMP_7950NL_Epson_ELPLP_22Installation guide to Epson EMP-7950NL projector lamp

You can expect between 1900 to 2900 hours of lamp life with the Epson EMP-7950NL projector lamp before you must to replace it.

When it’s time to replace the Epson EMP-7950NL projector lamp look for the seal of approval. You’ll want to install an authentic lamp and avoid generic lamps.

Generic lamps may look like a real bargain because they are generally cheaper that authentic lamps. Buyer beware! You get want you pay for and with generic “compatible” lamps that usually means a host of problems that can leave you with a damaged Epson EMP-7950NL projector.

6 reasons to avoid generic lamps:

Don’t be fooled by the generics. Learn the 7 Ways to Spot a Counterfeit Lamp. Buy a new Epson ELPLP22 model for your Epson EMP-7950NL projector.

End of life warnings

Epson_EMP_7950_Epson_ELPLP_22_warning_lamp_lightWhen the Epson EMP-7950NL projector lamp is reaching end of life look for the following warning signs:

  • The images gets darker or starts to deteriorates.
  • Colours on screen look off.
  • the message: LAMP REPLACE appears on screen.
  • The warning light begins flashing orange ours.

Installing a new Epson EMP-7950NL projector lamp

Before installing the new lamp:

  • Turn the projector power off and wait for the 20-second cool-down before disconnecting the power cable.
  • Wait at least 60 minutesfor the Epson EMP 7950NL projector to cool. These projectors operate under extremely high temperatures so be patient and wait until the projector is cool or you can be badly burned!
  • CAUTION: If your projector is mounted on the ceiling, don’t standing directly underneath in case there is any broken glass from the lamp. Stand to the side of the projector and not underneath it.

NOTE: Do not operate the projectors while the lamp is removed as this may result in malfunctions, fire hazard and other accidents.

 

Epson_EMP_7950_Epson_ELPLP_22_remove_lamp_cover

 

Insert the screwdriver into the hollow between the Epson EMP 7950NL projector and lamp cover. Turn the screwdriver to release the lock. Slide the screwdriver in until the arrow mark on the lamp and arrow on the projector are aligned. Lift up the lamp cover to remove it.

 

 

 

 

Epson_EMP_7950NL_Epson_ELPLP_22_loosen_screws

 

Insert the screwdriver supplied with the new Epson ELPLP22 lamp or use a flat-tipped screwdriver and loosen the two screws holding the lamp in place.

 

 

 

 

Epson_EMP_7950NL_Epson_ELPLP_22_remove_lamp

Lift up the wire handle on the Epson ELPLP22 lamp and use it to pull the lamp straight out of the projector. NOTE: The Epson ELPLP22 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

 

 

 

 

 

Epson_EMP_7950NL_Epson_ELPLP_22_loosen_screws

 

Hold the new lamp so it faces the correct way. Insert the Epson ELPLP22 lamp until it clicks into place and then tighten the two screws holding the lamp in place. Avoid touching the actual bulb as the oil from your fingers will leave marks that will show up on screen. Also avoid knocking bulb as it may break. Learn what to do should the bulb shatter.

Tighten the two screws on the Epson ELPLP22 lamp.

 

 

Epson_EMP_7950_Epson_ELPLP_22_remove_lamp_cover

Slide the Epson EMP 7950NL lamp cover back on until it clicks into place. You are now ready to reset the lamp timer.

Resetting the Epson EMP 7950NL lamp timer

The Epson EMP 7950NL projector has a built-in timer tracking the number of hours the Epson ELPLP22 lamp has been used. When it hits close to 1900 hours, the lamp timer will trigger the replacement lamp message as well as the warning light. In order for the lamp timer to properly do its job, it need to be reset whenever a new lamp is installed. Failure to reset the Epson ELPLP22 lamp timer can result in the lamp being used beyond it’s recommended life and damaging the projector.

Epson_EMP_7950_Epson_ELPLP_22_lamp_timer_resetPlug the projector in and turn it on.

  • Press the MENU button on the remote or the Auto/Enter on the Epson EMP 7950NL projector’s control panel .
  • Scroll down to the ABOUT menu. Press ENTER. The number of hours will be displayed as 0H until 10 hours of lamp use is reached.
  • Scroll down to RESET LAMP TIMER. Press ENTER.

 

Epson_Powerlite_7950_Epson_ELPLP_22_reset_lamp_timer_screen2

  • A second prompt screen will appear.
  • Select YES and press ENTER.
  • The lamp hours will be reset to zero.
  • Press MENU to exit this screen.

 

 

How to extend the life of the Epson ELPLP22 lamp:

Extend the life of the newly installed Epson ELPLP22 with the following tips:

  • Keep your air filters clean to avoid overheating the projector.
  • Turn off the Epson EMP 7950NL projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
  • Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
  • Set the Brightness Mode to low or Econo Mode to extend lamp life.
  • Learn more with Top tips for extending DLP projector lamp life.
Tagged with: , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Epson_PowerLite_7850NL_Epson_ELPLP_22Replacing the Epson PowerLite 7850pNL projector lamp is simple and fast when you follow our guide.

Be sure to buy an authentic Epson PowerLite 7850pNL projector lamp from a recognized dealer.

Go with authentic

It can be overwhelming trying to find the best dealer for your Epson PowerLite 7850pNL projector. Look for the seal of approval before purchasing your Epson ELPLP22 lamp. Avoid generic lamps. Their inferior workmanship can seriously damage the optics in your Epson PowerLite 7850pNL since they have not been calibrated properly. Generics also don’t last the full 2000 hours and pose a health hazard due to the toxic materials.

Avoid all these problems and keep the warranty on your Epson Powerlite 7850pNL projector valid (using generic automatically voids your warranty). Don’t be fooled by the generic manufacturers. Learn the 7 Ways to Spot a Counterfeit Lamp and

Warning signs

You can expect between 2000 to 3000 hours of lamp life before you must install a replacement. Set the brightness to low to get the maximum hours and be sure to keep your filters cleaned. Warning signs that the Epson ELPLP22 lamp is reaching end of life include:

  • image getting darker or starting to deteriorates.
  • colours look off.
  • LAMP REPLACE messages appears on screen.
  • warning light flashing orange. When the lamp light is flashing RED, the Epson ELPLP22 lamp is burnt out and must be replaced immediately.

Replacing the Epson ELPLP22 lamp

Follow these important steps before installing a new Epson ELPLP22 lamp in the Epson PowerLite 7850pNL projector:

  • Turn off the projector power.
  • When the power light stops flashing unplug the power cord.
  • Wait at least 60 minutes for the Epson PowerLite 7850pNL projector to cool internally before opening it up. It should be cool to the touch. These projectors operate under extremely high temperatures so be patient and wait until the projector is cool or you run the risk of burning yourself.

NOTE: Do not operate the projectors while the lamp is removed as this may result in malfunctions, fire hazard and other accidents.

Epson_PowerLite 7850pNL_Epson_ELPLP_22

 

The Epson ELPLP22 lamp comes with a replacement air filter. To change filters: turn the Epson PowerLite 7850pNL projector over and remove the air filters at the side and bottom of the projector. Slide the new filters in until they click into place.

 

Epson_PowerLite 7850pNL_Epson_ELPLP_22

Insert the screwdriver supplied with the new Epson ELPLP22 lamp or use a flat-tipped screwdriver. Place the tip of the screwdriver into the space beside the air vent on the Epson PowerLite 7850pNL. Gently slide the lamp cover to align the arrow on the cover with the arrow on the projector.

Epson_PowerLite 7850pNL_loosen_screws_Epson_ELPLP_22Loosen the two screws holding the Epson ELPLP22 lamp in place (they will not come all the way out).

NOTE: The Epson ELPLP22 lamp contains mercury and should be recycled rather than being thrown into regular garbage. Recycle these lamps.
Epson_PowerLite 7850pNL_Epson_ELPLP_22Lift up the wire handle on the Epson ELPLP22 lamp and it up straight out of the projector. Gently insert the new Epson ELPLP22 lamp while keeping your hands off the bulb. Fingerprints can leave marks on the screen. Learn what to do should the bulb shatter.

Tighten the screws and replace the lamp cover. NOTE: The projector will not turn on if the lamp cover is loose. You are now ready to reset the lamp timer.

Resetting the Epson PowerLite 7850pNL lamp timer

The lamp timer will track the life of the Epson ELPLP22 lamp and triggers the warning messages. It’s critical to reset the lamp timer whenever you replace the lamp in the Epson PowerLite 7850pNL projector.

 

Epson_PowerLite 7850pNL_Epson_ELPLP_22

  • Plug the projector in and turn it on.
  • Press the MENU button on the remote or on the projector’s control panel to display the Main menu,
  • Use the pointer buttons on the remote or the arrow buttons on the Epson PowerLite 7850p to scroll down to the ABOUT menu. Press ENTER to display the ABOUT screen information.
  • Scroll down to RESET LAMP TIMER option.
  • Press ENTER to open the second prompt screen.

 

 

Epson_PowerLite 7850pNL_Epson_ELPLP_22

 

Select YES and press ENTER.

  • The lamp hours will be reset to zero.
  • NOTE: Lamp usage appears as 0H until you’ve used at least 10 hours of lamp life
  • Press ESC or MENU to exit this screen.

 

How to extend the life of the Epson ELPLP22 lamp:

Extend the life of the newly installed Epson ELPLP22 with the following tips:

  • Keep your air filters clean to avoid overheating the projector.
  • Turn off the Epson PowerLite 7850pNL projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
  • Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
  • Set the Brightness Mode to low to extend lamp life.
  • Learn more with Top tips for extending DLP projector lamp life.
Tagged with: , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Epson_Powerlite_7800p_Epson_ELPLP_22 Replace the Epson EMP-7800P projector lamp using this how to guide.

If the image on your projector has dimmed or starting to deteriorate it’s time to replace the Epson EMP-7800P projector lamp. Follow our guide!

You’ll need the Epson ELPLP22 model.  Be sure to buy a Epson EMP-7800P projector lamp from a recognized dealer.

You can expect between 2000 to 3000 hours of lamp life before you must install a replacement. Set the brightness to low to get the maximum hours and be sure to keep your filters cleaned.

The importance of buying authentic

There are many copy cat manufacturers selling knock-off Epson ELPLP22 lamps. Despite their bargain prices, these generic lamps end up costing you more because of their many problems:

Don’t be fooled by the generic manufacturers. Learn the 7 Ways to Spot a Counterfeit Lamp and look for the seal of approval.

End of life warning signs

Warning signs that the Epson ELPLP22 lamp is reaching end of life include:

  • image gets darker or starting to deteriorates.
  • colours look off.
  • LAMP REPLACE messages appears on screen.
  • warning light flashing orange. When the lamp light is flashing RED, the Epson ELPLP22 lamp is burnt out and must be replaced immediately.

Replacing the Epson EMP-7800P projector lamp

Follow these important steps before installing a new Epson ELPLP22 lamp in the Epson EMP- 7800p projector:

  • Turn off the projector power and wait for the power light to stop flashing before unplugging the power cord.
  • Wait until the Epson EMP-7800p is cool to the touch (about 60 minutes). These projectors operate under extremely high temperatures so be patient and wait until the projector is cool or you run the risk of burning yourself.

NOTE: Do not operate the projectors while the lamp is removed as this may result in malfunctions, fire hazard and other accidents.

Epson_EMP_7800p_Epson_ELPLP_22

 

The Epson ELPLP22 lamp comes with a replacement air filter so you should change the filter at the same time. To change filters: turn the Epson EMP 7800p projector over and remove the air filters at the side and bottom of the projector. Replace the new filters — they should pop into place smoothly.

 

Epson_EMP_7800p_Epson_ELPLP_22

Insert the screwdriver supplied with the new Epson ELPLP22 lamp or use a flat-tipped screwdriver. Place the tip of the screwdriver into the space beside the air vent on the Epson EMP 7800p projector and gently slide the lamp cover to align the arrow on the cover with the arrow on the projector.

 

 

Epson_EMP_7850p_loosen_screws_Epson_ELPLP_22

 

Loosen the two screws holding the Epson ELPLP22 lamp in place (they will not come all the way out). Lift up the wire handle on the Epson ELPLP22 lamp and use it to pull the lamp straight out of the projector.

NOTE: The Epson ELPLP22 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

Epson_EMP_7800p_Epson_ELPLP_22Gently insert the new Epson ELPLP22 lamp. Avoid touching the actual bulb as the oil from your fingers will leave marks that will show up on screen. Also avoid knocking bulb as it may break. Learn what to do should the bulb shatter.

Tighten the screws and replace the lamp cover. NOTE: The projector will not turn on if the lamp cover is loose.

You are now ready to reset the lamp timer.

Resetting the Epson EMP 7800p lamp timer

The lamp timer in the Epson EMP 7800p tracks the life of the Epson ELPLP22 lamp and triggers the lamp warning messages. Always reset the lamp timer whenever you replace the Epson ELPLP22 lamp timer.

Epson_EMP_7800p_reset_lamp_timer_Epson_ELPLP_22

  • Plug the projector in and turn it on.
  • Press the MENU button on the remote or on the projector’s control panel to display the Main menu,
  • Use the pointer buttons on the remote or the arrow buttons on the Epson PowerLite 7800p to scroll down to the ABOUT menu. Press ENTER to display the ABOUT screen information.
  • Scroll down to RESET LAMP TIMER option.
  • Press ENTER to open the second prompt screen.

Epson_EMP_7800p_reset_lamp_timer_screen2_Epson_ELPLP_22Select YES and press ENTER.

  • The lamp hours will be reset to zero.
  • NOTE: Lamp usage appears as 0H until you’ve used at least 10 hours of lamp life
  • Press ESC or MENU to exit this screen.

 

How to extend the life of the Epson ELPLP22 lamp:

Extend the life of the newly installed Epson ELPLP22 with the following tips:

  • Keep your air filters clean to avoid overheating the projector.
  • Turn off the Epson EMP 7800p projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
  • Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
  • Set the Brightness Mode to low to extend lamp life.
  • Learn more with Top tips for extending DLP projector lamp life.
Tagged with: , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Epson_EMP_7850p_Epson_ELPLP_22Follow this 3-step guide for installing a new Epson EMP-7850p projector lamp.

Be sure to buy an authentic Epson EMP-7850p projector lamp from a recognized dealer.

Step 1: Know when to replace

You can expect between 2000 to 3000 hours of lamp life before you must install a replacement. Set the brightness to low to get the maximum hours and be sure to keep your filters cleaned.

Warning signs that the Epson EMP-7850p projector lampis reaching end of life include:

  • image getting darker or starting to deteriorates.
  • colours look off.
  • LAMP REPLACE messages appears on screen.
  • warning light flashing orange. When the lamp light is flashing RED, the Epson EMP-7850p projector lamp is burnt out and must be replaced immediately.

Step 2: Buying the right lamp

There are many copy cat manufacturers selling knock-off Epson EMP-7850p projector lamp Despite their bargain prices, these generic lamps end up costing you more because of their inferior workmanship. They can seriously damaged the optics in your Epson EMP-7850p since they have not been calibrated properly. Generic, compatible lamps also don’t last the full 2000 hours. Even more troublesome is the health hazard they pose due to the toxic materials.

Avoid all these problems and keep the warranty on your Epson EMP-7850p projector valid (using generic automatically voids your warranty). Don’t be fooled by the generic manufacturers. Learn the 7 Ways to Spot a Counterfeit Lamp and look for the seal of approval.

Step 3: Replacing the Epson ELPLP22 lamp

Follow these important steps before installing a new Epson EMP-7850p projector projector lamp. Be sure to buy the Epson ELPLP22 lamp model:

  • Turn off the projector power.
  • When the power light stops flashing unplug the power cord.
  • Wait at least 60 minutes for the Epson EMP-7850p projector to cool internally before opening it up. It should be cool to the touch. These projectors operate under extremely high temperatures so be patient and wait until the projector is cool or you run the risk of burning yourself.

NOTE: Do not operate the projectors while the lamp is removed as this may result in malfunctions, fire hazard and other accidents.

Epson_EMP_7850p_Epson_ELPLP_22

 

The Epson ELPLP22 lamp comes with a replacement air filter so you should change the filter at the same time. To change filters: turn the Epson EMP-7850p projector over and remove the air filters at the side and bottom of the projector. Replace the new filters — they should pop into place smoothly.

 

 

Epson_EMP_7850p_Epson_ELPLP_22

Insert the screwdriver supplied with the new Epson ELPLP22 lamp or use a flat-tipped screwdriver. Place the tip of the screwdriver into the space beside the air vent on the Epson EMP-7850p and gently slide the lamp cover to align the arrow on the cover with the arrow on the projector.

 

 

Epson_EMP_7850p_loosen_screws_Epson_ELPLP_22

 

Loosen the two screws holding the Epson ELPLP22 lamp in place (they will not come all the way out).

NOTE: The Epson ELPLP22 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

 

 

 

Epson_EMP_7850p_Epson_ELPLP_22

Lift up the wire handle on the Epson ELPLP22 lamp and use it to pull the lamp straight out of the projector. Gently insert the new Epson ELPLP22 lamp. Avoid touching the actual bulb as the oil from your fingers will leave marks that will show up on screen. Also avoid knocking bulb as it may break. Learn what to do should the bulb shatter.

Tighten the screws and replace the lamp cover. NOTE: The projector will not turn on if the lamp cover is loose. You are now ready to reset the lamp timer.

Resetting the Epson EMP-7850p lamp timer

The lamp timer will track the life of the Epson ELPLP22 lamp and trigger the lamp warning messages. Therefore, it’s critical to reset the lamp timer whenever you replace the lamp in the Epson EMP-7850p projector. Do not re-set the Epson ELPLP22 lamp timer with an already used lamp as this may cause it to be used beyond its designated lamp life and cause an explosion.

 

Epson_EMP_7850p_Epson_ELPLP_22

  • Plug the projector in and turn it on.
  • Press the MENU button on the remote or on the projector’s control panel to display the Main menu,
  • Use the pointer buttons on the remote or the arrow buttons on the Epson PowerLite 7850p to scroll down to the ABOUT menu. Press ENTER to display the ABOUT screen information.
  • Scroll down to RESET LAMP TIMER option.
  • Press ENTER to open the second prompt screen.

Epson_EMP_7850p_Epson_ELPLP_22

Select YES and press ENTER.

  • The lamp hours will be reset to zero.
  • NOTE: Lamp usage appears as 0H until you’ve used at least 10 hours of lamp life
  • Press ESC or MENU to exit this screen.

 

How to extend the life of the Epson ELPLP22 lamp:

Extend the life of the newly installed Epson ELPLP22 with the following tips:

  • Keep your air filters clean to avoid overheating the projector.
  • Turn off the Epson EMP-7850p projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
  • Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
  • Set the Brightness Mode to low to extend lamp life.
  • Learn more with Top tips for extending DLP projector lamp life.
Tagged with: , , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Epson_Powerlite_7850p_Epson_ELPLP_22Wondering when to replace the Epson PowerLite 7850p projector lamp? Follow our guide to learn how.

Your Epson PowerLite 7850p uses the Epson ELPLP22 lamp. You can expect between 2000 to 3000 hours of Epson PowerLite 7850p projector lamp life before you must install a replacement. Be sure to buy an authentic Epson PowerLite 7850p projector lamp from a recognized dealer.

Replacement warning signs

Epson_Powerlite_7850p_Lamp_warning_lightEpson_ELPLP_22The Epson PowerLite 7850p projector lamp typically lasts to 2000 hours if the brightness is set to high and up to 3000 hours when set to low.

Warning signs that the Epson PowerLite 7850p projector lamp is reaching end of life include:

  • image gettings darker or starting to deteriorates.
  • colours look off.
  • LAMP REPLACE mesaages appears on screen.
  • warning light  flashing orange. When the lamp light is flashing RED, the Epson PowerLite 7850p projector lamp is burnt out and must be replaced immediately.

Why buy authentic?

Avoid generic lamps even though they appear to be a great altenative. They usually end up costing you more because of their inferior workmanship and inability to be calibrated properly so as not to damage the optics. Generic, compatible lamps also don’t last the full 2000 hours.thEven more troublesome is the health hazard they pose due to the toxic materials.

Avoid all these problems and keep the warranty on your Epson Powerlite 7850p projector valid (using generic automatically voids your warranty). Don’t be fooled by the generic manufacturers. Learn the 7 Ways to Spot a Counterfeit Lamp and look for the seal of approval.

Replacing the Epson ELPLP22 lamp

Follow these important steps before installing the Epson ELPLP22 model into the Epson PowerLite 7850p projector:

  • Turn off the projector power.
  • When the power light stops flashing unplug the power cord.
  • Wait at least 60 minutesfor the Epson PowerLite 7850p projector to cool internally before opening it up. It should be cool to the touch. These projectors operate under extremely high temperatures so be patient and wait until the projector is cool or you run the risk of burning yourself.

NOTE: Do not operate the projectors while the lamp is removed as this may result in malfunctions, fire hazard and other accidents.

Epson_Powerlite_7850p_Epson_ELPLP_22

 

The Epson ELPLP22 lamp comes with a replacement air filter so you should change the filter at the same time. To change filters: turn the PowerLite 7850p projector over and remove the air filters at the side and bottom of the projector. Replace the new filters — they should pop into place smoothly.

 

Epson_Powerlite_7850p_Epson_ELPLP_22

Insert the screwdriver supplied with the new Epson ELPLP22 lamp or use a flat-tipped screwdriver. Place the tip of the screwdriver into the space beside the air vent on the Epson PowerLite 7850p projector and gently slide the lamp cover to align the arrow on the cover with the arrow on the projector.

 

 

Epson_Powerlite_7850p_loosen_screws_Epson_ELPLP_22

Loosen the two screw holding the Epson ELPLP22 lamp in place (they will not come all the way out). NOTE: The Epson ELPLP22 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

 

 

Epson_Powerlite_7850p_Epson_ELPLP_22

Lift up the wire handle on the Epson ELPLP22 lamp and use it to pull the lamp straight out of the projector. Gently insert the new Epson ELPLP22 lamp. Avoid touching the actual bulb as the oil from your fingers will leave marks that will show up on screen. Also avoid knocking bulb as it may break. Learn what to do should the bulb shatter.

Tighten the screws and replace the lamp cover. NOTE: The projector will not turn on if the lamp cover is loose. You are now ready to reset the lamp timer.

Resetting the Epson PowerLite 7850p lamp timer

The lamp timer will track the life of the Epson ELPLP22 lamp and trigger the lamp warning messages. Therefore, it’s critical to reset the lamp timer whenever you replace the lamp in the Epson PowerLite 7850p projector. Do not re-set the Epson ELPLP22 lamp timer with an already used lamp as this may cause it to be used beyond its designated lamp life and cause an explosion.

Epson_Powerlite_7850p_Epson_ELPLP_22

  • Plug the projector in and turn it on.
  • Press the MENU button on the remote or on the projector’s control panel to display the Main menu,
  • Use the pointer buttons on the remote or the arrow buttons on the Epson PowerLite 7900p to scroll down to the ABOUT menu. Press ENTER to display the ABOUT screen information.
  • Scroll down to RESET LAMP TIMER option.
  • Press ENTER to open the second prompt screen.

Epson_Powerlite_7850p_Epson_ELPLP_22

Select YES and press ENTER.

  • The lamp hours will be reset to zero.
  • NOTE: Lamp usage appears as 0H until you’ve used at least 10 hours of lamp life
  • Press ESC or MENU to exit this screen.

How to extend the life of the Epson ELPLP22 lamp:

Extend the life of the newly installed Epson ELPLP22 with the following tips:

  • Keep your air filters clean to avoid overheating the projector.
  • Turn off the Epson PowerLite 7850p projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
  • Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
  • Set the Brightness Mode to low or Econo Mode to extend lamp life.
  • Learn more with Top tips for extending DLP projector lamp life.
Tagged with: , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

epson-emp-7900_projectorInstall a new Epson EMP-7900 projector lamp in three easy steps.

You can expect between 1900 to 2900 hours of lamp life with the Epson EMP-7900 projector lamp before you must to replace it.

Step 1: Buying the correct lamp

When it’s time to replace the Epson EMP-7900 projector lamp be sure to purchase an authentic lamp. Avoid generic lamps.

Generic lamps may look like a real bargain because they are generally cheaper that authentic lamps. Buyer beware! You get want you pay for and with generic “compatible” lamps that usually means a host of problems that can leave you with a damaged Epson EMP-7900 projector. Be sure to purchase the Epson ELPLP22 lamp model.

6 reasons to avoid generic lamps:

Look for the seal of approval and don’t be fooled into buying a generic lamp.  Learn how to Spot a Counterfeit Lamp.

Step 2: Know when to replacement the Epson EMP-7900 projector lamp

Epson_EMP_7900_Epson_ELPLP_22When the Epson EMP-7900 projector lamp is reaching end of life look for the following warning signs:

  • The images gets darker or starts to deteriorates.
  • Colours on screen look off.
  • the message: LAMP REPLACE appears on screen.
  • The warning light begins flashing orange ours.

Step 3: Replacing the Epson EMP-7900 projector lamp

Before installing the new lamp:

  • Turn the projector power off.
  • Wait for a 20-second cool-down.
  • Disconnect the power cable.
  • Give the Epson EMP 7900 at least 60 minutes to cool. These projectors operate under extremely high temperatures so be patient and wait until the projector is cool or you can be badly burned!
  • CAUTION: If your projector is mounted on the ceiling, don’t standing directly underneath in case there is any broken glass from the lamp. Stand to the side of the projector and not underneath it.

NOTE: Do not operate the projectors while the lamp is removed as this may result in malfunctions, fire hazard and other accidents.

Epson_EMP_7900_Epson_ELPLP_22

Insert the screwdriver into the hollow between the Epson EMP 7900 projector and lamp cover. Turn the screwdriver to release the lock. Slide the screwdriver in until the arrow mark on the lamp and arrow on the projector are aligned. Lift up the lamp cover to remove it.

Insert the screwdriver supplied with the new Epson ELPLP22 lamp or use a flat-tipped screwdriver and loosen the two screws holding the lamp in place.

 

Epson_EMP_7900_Epson_ELPLP_22Lift up the wire handle on the Epson ELPLP22 lamp and use it to pull the lamp straight out of the projector. NOTE: The Epson ELPLP22 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

 

Epson_EMP_7900_Epson_ELPLP_22

Hold the new lamp so it faces the correct way. Insert the Epson ELPLP22 lamp until it clicks into place and then tighten the two screws holding the lamp in place. Avoid touching the actual bulb as the oil from your fingers will leave marks that will show up on screen. Also avoid knocking bulb as it may break. Learn what to do should the bulb shatter.

Tighten the two screws on the Epson ELPLP22 lamp.

Epson_EMP_7900_Epson_ELPLP_22Slide the Epson EMP 7900 lamp cover back on until it clicks into place. You are now ready to reset the lamp timer.

 Resetting the Epson EMP 7900 lamp timer

You must reset the lamp timer in the Epson EMP 7900 projector every time a new lamp has been installed. The projector has a built-in timer tracking the number of hours the Epson ELPLP22 lamp has been used. When it hits close to 1900 hours, the lamp timer will trigger the replacement lamp message as well as the warning light. In order for the lamp timer to properly do its job, it need to be reset whenever a new lamp is installed. Failure to reset the Epson ELPLP22 lamp timer can result in the lamp being used beyond it’s recommended life and damaging the projector.

 

  • Epson_EMP_7900_Epson_ELPLP_22Plug the projector in and turn it on.
  • Press the MENU button on the remote or the Auto/Enter on the Epson EMP 7900 projector’s control panel .
  • Scroll down to the ABOUT menu. Press ENTER. The number of hours will be displayed as 0H until 10 hours of lamp use is reached.
  • Scroll down to RESET LAMP TIMER. Press ENTER.

Epson_Powerlite_7900_Epson_ELPLP_22

  • A second prompt screen will appear.
  • Select YES and press ENTER.
  • The lamp hours will be reset to zero.
  • Press MENU to exit this screen.

 

How to extend the life of the Epson ELPLP22 lamp:

Extend the life of the newly installed Epson ELPLP22 with the following tips:

  • Keep your air filters clean to avoid overheating the projector.
  • Turn off the Epson EMP 7900 projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
  • Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
  • Set the Brightness Mode to low or Econo Mode to extend lamp life.
  • Learn more with Top tips for extending DLP projector lamp life.
Tagged with: , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP — No Comments ↓

Change the Epson EMP-7950 projector lamp in three easy steps.

Be sure to invest in an authentic Epson EMP-7950 projector lamp.

Step 1: Finding the right Epson EMP-7950 projector lamp

Epson_EMP_7950_Epson_ELPLP_22

You can expect between 1900 to 2900 hours of lamp life with the Epson EMP-7950 projector lamp before you must to replace the lamp.

When it’s time to replace Epson EMP-7950 projector lamp look for the seal of approval. You’ll want to install an authentic lamp and avoid generic lamps.

Generic lamps may look like a real bargain because they are generally cheaper that authentic lamps. Buyer beware! You get want you pay for and with generic “compatible” lamps that usually means a host of problems that can leave you with a damaged Epson EMP-7950 projector.

6 reasons to avoid generic lamps:

Don’t be fooled by the generic manufacturers: Learn the 7 Ways to Spot a Counterfeit Lamp.

Step 2: Know when to replacement lamp

Epson_EMP_7950_Epson_ELPLP_22When theEpson EMP-7950 projector lamp  is reaching end of life look for the following warning signs:

  • The images gets darker or starts to deteriorate.
  • Colours on screen look off.
  • the message: LAMP REPLACE appears on screen.
  • The warning light begins flashing orange.

You’ll need to purchase the Epson ELPLP22 model.

Step 3: Replacing the Epson ELPLP22 lamp

Before installing the new lamp:

  • Turn the projector power off and wait for the 20-second cool-down before disconnecting the power cable.
  • Wait at least 60 minutesfor the Epson EMP 7950 projector to cool. These projectors operate under extremely high temperatures so be patient and wait until the projector is cool or you can be badly burned!
  • CAUTION: If your projector is mounted on the ceiling, don’t standing directly underneath in case there is any broken glass from the lamp. Stand to the side of the projector and not underneath it.

NOTE: Do not operate the projectors while the lamp is removed as this may result in malfunctions, fire hazard and other accidents.

Epson_EMP_7950_Epson_ELPLP_22

 

Insert the screwdriver into the hollow between the Epson EMP 7950 projector and lamp cover. Turn the screwdriver to release the lock. Slide the screwdriver in until the arrow mark on the lamp and arrow on the projector are aligned. Lift up the lamp cover to remove it.

 

 

Epson_EMP_7950_Epson_ELPLP_22

 

Insert the screwdriver supplied with the new Epson ELPLP22 lamp or use a flat-tipped screwdriver and loosen the two screws holding the lamp in place.

 

 

 

Epson_EMP_7950_Epson_ELPLP_22

Lift up the wire handle on the Epson ELPLP22 lamp and use it to pull the lamp straight out of the projector. NOTE: The Epson ELPLP22 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

 

 

 

 

Epson_EMP_7950_Epson_ELPLP_22

 

Hold the new lamp so it faces the correct way. Insert the Epson ELPLP22 lamp until it clicks into place and then tighten the two screws holding the lamp in place. Avoid touching the actual bulb as the oil from your fingers will leave marks that will show up on screen. Also avoid knocking bulb as it may break. Learn what to do should the bulb shatter.

Tighten the two screws on the Epson ELPLP22 lamp.

 

Epson_EMP_7950_Epson_ELPLP_22

Slide the Epson EMP 7950 lamp cover back on until it clicks into place. You are now ready to reset the lamp timer.

 Resetting the Epson EMP 7950 lamp timer

The Epson EMP 7950 projector has a built-in timer tracking the number of hours the Epson ELPLP22 lamp has been used. When it hits close to 1900 hours, the lamp timer will trigger the replacement lamp message as well as the warning light. In order for the lamp timer to properly do its job, it need to be reset whenever a new lamp is installed. Failure to reset the Epson ELPLP22 lamp timer can result in the lamp being used beyond it’s recommended life and damaging the projector.

Epson_EMP_7950_Epson_ELPLP_22Plug the projector in and turn it on.

  • Press the MENU button on the remote or the Auto/Enter on the Epson EMP 7950 projector’s control panel .
  • Scroll down to the ABOUT menu. Press ENTER. The number of hours will be displayed as 0H until 10 hours of lamp use is reached.
  • Scroll down to RESET LAMP TIMER. Press ENTER.

 

 

 

Epson_Powerlite_7950_Epson_ELPLP_22

  •  A second prompt screen will appear.
  • Select YES and press ENTER.
  • The lamp hours will be reset to zero.
  • Press MENU to exit this screen.

How to extend the life of the Epson ELPLP22 lamp:

Extend the life of the newly installed Epson ELPLP22 with the following tips:

  • Keep your air filters clean to avoid overheating the projector.
  • Turn off the Epson EMP 7950 projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
  • Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
  • Set the Brightness Mode to low or Econo Mode to extend lamp life.
  • Learn more with Top tips for extending DLP projector lamp life.
Tagged with: , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Epson_EMP_7900NL_Epson_ELPLP_22Follow this easy guide to replace the Epson EMP-7900NL projector lamp

Be sure to buy an authentic Epson EMP-7900NL projector lamp from a recognized dealer.

Step 1: Finding the right lamp

You can expect between 2000 to 3000 hours of lamp life before you must to install a replacement.

Look for the seal of approval when you are buying your Epson EMP-7900NL projector lamp and avoid generic lamps. While generic have a lower pricetag, there are plenty of downsides to these generic lamps including

Don’t be fooled by the generic manufacturers: Learn the 7 Ways to Spot a Counterfeit Lamp.

Step 2: Know when to replace

Epson_Powerlite_7900p_Lamp_warning_lightEpson_ELPLP_22When the Epson EMP-7900NL projector lamp is reaching end of life look for the following warning signs:

  • The images gets darker or starts to deteriorates.
  • Colours on screen look off.
  • LAMP REPLACE appears on screen.
  • The warning light begins flashing orange followed by a steady red light. When the lamp light is flashing RED the lamp is burnt out and must be replaced.
  • When the brightness control is set to high the Epson ELPLP22 lamp typically lasts to 2000 hours. When the brightness control is set to low, the lamp will last up to 3000 hours.

Step 3: Replacing the Epson ELPLP22 lamp

Before installing the new lamp:

  • Turn off the projector power.
  • When the power light stops flashing unplug the power cord.
  • Wait at least 60 minutesfor the Epson EMP-7900NL projector to cool internally before opening it up. It should be cool to the touch. These projectors operate under extremely high temperatures so be patient and wait until the projector is cool or you run the risk of burning yourself.

NOTE: Do not operate the projectors while the lamp is removed as this may result in malfunctions, fire hazard and other accidents.

Be sure to buy a Epson ELPLP22 lamp model:

Epson_EMP_7900NL_Epson_ELPLP_22

The Epson ELPLP22 lamp comes with a replacement air filter so you should change the filter at the same time. To change filters: turn the projector over and remove the air filters at the side and bottom of the projector. Replace the new filters — they should pop into place smoothly.

 

Epson_EMP_7900p_Epson_ELPLP_22

Insert the screwdriver supplied with the new Epson ELPLP22 lamp or use a flat-tipped screwdriver. Place the tip of the screwdriver into the space beside the air vent on the Epson EMP-7900NL projector and gently slide the lamp cover to align the arrow on the cover with the arrow on the projector.

 

 

Epson_EMP_7900NL_loosen_screws_Epson_ELPLP_22

Loosen the two screw holding the Epson ELPLP22 lamp in place (they will not come all the way out). NOTE: The Epson ELPLP22 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

 

 

Epson_EMP_7900NL_Epson_ELPLP_22

Lift up the wire handle on the Epson ELPLP22 lamp and use it to pull the lamp straight out of the projector. Gently insert the new Epson ELPLP22 lamp. Tighten the screws and replace the lamp cover. NOTE: The Epson EMP-7900NL projector will not turn on if the lamp cover is loose.

You are now ready to reset the lamp timer.

 

Resetting the Epson EMP-7900NL lamp timer

The lamp timer will track the life of the Epson ELPLP22 lamp and trigger the lamp warning messages. Therefore, it’s critical to reset the lamp timer whenever you replace the Epson ELPLP22 lamp lamp in the Epson EMP-7900NL projector. Do not re-set the Epson ELPLP22 lamp timer with an already used Epson ELPLP22 lamp as this may cause the lamp to be used beyond its designated lamp life and cause an explosion.

Epson_EMP_7900NL_Epson_ELPLP_22

  • Plug the projector in and turn it on.
  • Press the MENU button on the remote or on the projector’s control panel to display the Main menu,
  • Use the pointer buttons on the remote or the arrow buttons on the Epson EMP 7900p to scroll down to the ABOUT menu. Press ENTER to display the ABOUT screen information.
  • Scroll down to RESET LAMP TIMER option.
  • Press ENTER to open the second prompt screen.

 

Epson_EMP_7900NL_Epson_ELPLP_22

Select YES and press ENTER.

  • The lamp hours will be reset to zero.
  • NOTE: Lamp usage appears as 0H until you’ve used at least 10 hours of lamp life
  • Press ESC or MENU to exit this screen.

How to extend the life of the Epson ELPLP22 lamp:

Extend the life of the newly installed Epson ELPLP22 with the following tips:

  • Keep your air filters clean to avoid overheating the projector.
  • Turn off the Epson EMP-7900NL projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
  • Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
  • Set the Brightness Mode to low or Econo Mode to extend lamp life.
  • Learn more with Top tips for extending DLP projector lamp life.
Tagged with: , , ,
Join the discussion on Facebook! All your questions, answered! The Screen & Projector Group