About Us - Page 87 of 171 - DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP

Replace the Epson PowerLite Home Cinema 720

Shelagh McNallyPosted on February 1, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

It’s easy to replace the lamp in our Epson PowerLite Home Cinema 720. Our step-by-step guide shows you how to install a replacement Epson ELPLP39 lamp

How do I know when to replace?

The Info menu can show you how many hours are left until the Epson ELPLP39 reaches end of life. You can expect to 3000 hours — the projector is maintained regularly and not over used.

Also watch for these warning signs:

the projected image get darker
the warning lamp on the projector flashes red and then continues to flash every half-second
the message: “Replace the lamp” flashes on the screen when you start using the projector.

Go with authentic lamps

There are plenty of choices for a replacement Epson ELPLP39 being sold over the Internet. It’s buyer beware though with many knock-off lamps being sold. Look for the seal of approval and buy from an authentic manufacturer.

These “generic” lamps are sold at discount prices and investigation reveals these lamps are actually dangerous to use. They are filled with toxic substances such as Krypton-85, known to cause cancer. Would you compromise your health and risk your eyesight for the sake of a few dollars?

Since these copy cat lamps have been created without proper calibration, they can also damage the sensitive imaging electronics in your Epson PowerLite Home Cinema 720. They are also prone to explosions and have a much shorter life. When you buy authentic you’ll be getting a guarantee with your lamp and keeping your warranty valid.

Learn how to protect yourself from counterfeit manufacturers.

How to install the Epson ELPLP39

Preparations before replacing the lamp:

let the projector cool for one full hour before trying to replace the lamp. This projector operates under very high temperatures and will be very hot. You can suffer burns if you are change the lamp while the projector is still hot. too impatient to wait until the projector is cool enough.
press the power button and wait for the light to stop flashing.
turn off the power switch at the back on the projector
unplug any power cords to cables to prevent the projector from accidentally being turned on. running the projector without a lamp will damage the projector.

Press the latches holding the PowerLite Home Cinema 720 lamp cover in place. Gently lift off the cover and place it to one side.

Using the screw driver provided, loosen the two screws securing the Epson ELPLP39 lamp. They won’t come all the way out so simply loosen them enough so the lamp can be lifted out.

Grab the bottom of the Epson ELPLP39 lamp and pull it up with a straight motion. Be sure to properly dispose of the old lamp. Do not throw it into regular garbage as it contains mercury.

Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: Don’t throw the Epson ELPLP39 into regular garbage! This lamp contains mercury and should be properly recycled! Your authorized manufacturer will recycle the lamp for you at no extra cost. (Another reason to go with authentic lamps!)

Gently line up the new Epson ELPLP39 lamp and slide it into place. Make sure not to touch the glass portion of the lamp. The oil on your fingers may cause the lamp to stop before its time.

Tighten the screws on the Epson ELPLP39 lamp.

Replace the PowerLite Home Cinema 720 lamp cover making sure it’s clicked into place. Otherwise, the projector will not turn on. You are now ready to reset the Lamp Usage Timer.

Reset the Lamp Usage Timer

It’s important to reset the Lamp Usage Timer so the Epson PowerLite Home Cinema 720 projector will know when it’s time for a new Epson ELPLP39 lamp. Resetting the timer before installing a new Epson ELPLP39 can cause serious damage to your projector.

Plug the projector back in.
Turn on the power switch on
Press the Power button and wait for the Epson Home Cinema 108o to warm up.
Press the Menu button on either the projector or remote control.
Scroll down to the Reset menu option.
Select Reset Hours.
A confirmation message will appear asking if you want to reset the hours Click on yes.
Press the Select button.
Press the Menu button to exit.

NOTE: A reading of 0H on the lamp usage timer means you’ve used less than 10 hours of lamp time.

Tips for extending Epson ELPLP39 lamp life

Get more hours from your Epson ELPLP39 lamp by following these maintenance tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson PowerLite Home Cinema 720 projector and let it stand unused for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.

Learn more with Top tips for extending DLP projector lamp life.

3 Steps to a new Epson EMP-TW980 projector lamp

Shelagh McNallyPosted on February 1, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — 2 Comments ↓

Follow this handy 3-step manual for a quick and easy installation of a new EMP-TW980 projector lamp.

Step 1: Know when to replace

You can expect up to 1600 hours of =life before the Epson ELPLP39 lamp must be replaced. Lamp life for the Epson EMP-TW980 varies according to how much the projector is being used and if regular maintenance is being done.

Watch for the warning signs that it’s time to replace the Epson ELPLP39 lamp

the lamp warning on the projector started to blink red and continues blinking
the picture gets darker and continues to deteriorate
the message “Replace the lamp” appears on screen when the projector is turned on.

Step 2: Get the right lamp ready

Invest in an authentic Epson ELPLP39 lamp from an authorized manufacturer with the seal of approval.

Avoid the temptation to buy the cheaper priced generic lamps being sold by a number of companies, including some of the large Internet retailers. These “compatible” have not been built with the correct components and will damage the inside of your Epson EMP-TW980 projector.

Generic lamps present health risk. Since copycat manufacturers can’t get the proper materials they often using highly toxic substitutes. They are also prone to explosions and actually have a shorter life.

Learn how to spot a counterfeit and go with an authentic Epson ELPLP39. It’s worth the few extra dollars to save yourself problems and keep your warranty entact.

Step 3: Installing the Epson ELPLP39

Before installation follow these steps:

press the power button and wait for the light to stop flashing.
turn off the power switch at the back on the projector
unplug any power cords to cables to prevent the projector from accidentally being turned on.
give the projector one full hour to cool. The Epson EMP-TW980 operates on high heat and you will burn yourself the projector has not cooled down.

Gently press on the EMP-TW980 lamp cover. Slide is away from the projector and then lift up to remove.

Using the screw driver provided, locate the two screws holding the Epson ELPLP39 lamp in place. Loosen both screws (they will not come out of the lamp altogether).

Grab the handle on the Epson ELPLP39 and gently pull the lamp up. Pulling too quickly can break the glass bulb. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP39 contains mercury and SHOULD NOT be thrown into regular garbage! Please recycle! Your authorized manufacturer will recycle the lamp for you at no extra cost. (Another reason to go with authentic lamps!)

Remove the packaging from the new Epson ELPLP39 lamp being sure not to touch the glass bulb. Your fingerprints can leave oil marks on the glass causing black spots to appear on screen when the projector heats up.

Line up the Epson ELPLP39 lamp and gently lower it into the EMP-TW980 projector.

Line up the EMP-TW980 cover hinges with the projector and place the lamp cover into them. Slide the lamp cover back down and click it into place. You’re noew ready to reset the lamp operating timer.

Resetting the Lamp Operating Timer

The Lamp Operating Timer determines when the Epson ELPLP39 lamp is reaching its 1600 hours end of life. Only reset this option when you have installed a new lamp otherwise you run the risk of using an older lamp past its recommended usage. This can cause the old lamp to explode and damage the Epson EMP-TW980 projector.

To reset the Lamp Operating Timer:

Plug the power cord back into the projector
Press the on button and wait for the projector to warm up.
Press the MENU button to display the CONFIGURATION MENU.
Scroll down to select RESET menu.
Scroll down and choose RESET LAMP HOURS option
Press ENTER.
The reset lamp hour message will show up.

Select YES
Press ENTER.
Lamp hours will be set to zero.

Extending the Epson ELPLP39 lamp life

Get more hours from your Epson ELPLP39 lamp by following these maintenance tips:

To avoid overhearing the projector and causing the lamp to explode, keep the air filters clean.
Let the Epson EMP-TW980 rest for at least one hour per day.
Using it only our to five hours per day will give the lamp a longer life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted. Overheating can cause lamp failure.

Learn more with Top tips for extending DLP projector lamp life.

Tagged with: authentic lamps, authentic projector lamps, Epson ELPLP39 lamp, Epson EMP-TW980 projector, Epson projector lamps, genuine lamps, genuine projector lamps, how to replace Epson projector lamps, installation, lamp, Lamp replacement, replacement lamps, replacement projector lamps

Changing the Epson Powerlite Home Cinema 1080 UB lamp

Shelagh McNallyPosted on January 31, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — 2 Comments ↓

Replacing the Epson ELPLP39 lamp in your Epson PowerLite Home Cinema 1080 UB projector doesn’t have to be a complicated endeavour. Our guide outlines what to do for a quick replacement.

When to replace?

The Epson ELPLP39 lamp lasts up to 3000 hours. Use the the Info menu to see how many hours are left until the Epson ELPLP39 reaches end of life in the Epson PowerLite Home Cinema 1080 UB. Also watch for these warning signs:

the projected image get darker
the warning lamp on the projector flashes red and then continues to flash every half-second
the message: “Replace the lamp” flashes on the screen when you start using the projector.

Buying the best lamp

There are a lot of choices for buying a new Epson ELPLP39 lamp on the Internet. You need to approach many of the sites with caution since many are selling generic, knock-off lamps.

These “knock-off” lamps are sold at discount prices but can actually cost more in the long rung. They are also prone to explosions and have a much shorter life. Copy cat manufacturers have created these lamps with toxic substances such as Krypton-85, known to cause cancer. Would you compromise your health and risk your eyesight for the sake of a few dollars?

Generic lamps have been created without proper calibrating, they can also damage the sensitive imaging electronics in your Epson PowerLite Home Cinema 1080 UB. When you buy authentic you’ll be getting a guarantee with your lamp and keeping your warranty valid. Look for the seal of approval and buy from an authentic manufacturer.

Learn how to protect yourself from counterfeit manufacturers.

Step 3: Installing the Epson ELPLP39

Pre-installation preparations:

let the projector cool for one full hour before trying to replace the lamp. This projector operates under very high temperatures and will be very hot. You can suffer burns if you are change the lamp while the projector is still hot. too impatient to wait until the projector is cool enough.
press the power button and wait for the light to stop flashing.
turn off the power switch at the back on the projector
unplug any power cords to cables to prevent the projector from accidentally being turned on. running the projector without a lamp will damage the projector.

Press the latches holding the PowerLite Home Cinema 1080 UB lamp cover in place. Gently lift off the cover and place it to one side.

Using the screw driver provided, loosen the two screws securing the Epson ELPLP39 lamp. They won’t come all the way out so simply loosen them enough so the lamp can be lifted out.

Grab the bottom of the Epson ELPLP39 lamp and pull it up with a straight motion. Be sure to properly dispose of the old lamp. Do not throw it into regular garbage as it contains mercury.

Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: Don’t throw the Epson ELPLP39 into regular garbage! This lamp contains mercury and should not be properly recycled your used lamps! Your authorized manufacturer will recycle the lamp for you at no extra cost. (Another reason to go with authentic lamps!)

Gently line up the new Epson ELPLP39 lamp and slide it into place. Make sure not to touch the glass portion of the lamp. The oil on your fingers may cause the lamp to stop before its time.

Tighten the screws on the Epson ELPLP39 lamp.

Replace the PowerLite Home Cinema 1080 UB lamp cover making sure it’s clicked into place. Otherwise, the projector will not turn on. You are now ready to reset the Lamp Usage Timer.

Reset the Lamp Usage Timer

It’s important to reset the Lamp Usage Timer so the Epson PowerLite Home Cinema 1080 UB projector will know when it’s time for a new Epson ELPLP39 lamp. Resetting the timer before installing a new Epson ELPLP39 can cause serious damage to your projector.

Plug the projector back in.
Turn on the power switch on
Press the Power button and wait for the Epson Home Cinema 108o to warm up.
Press the Menu button on either the projector or remote control.
Scroll down to the Reset menu option.
Select Reset Hours.
A confirmation message will appear asking if you want to reset the hours Click on yes.
Press the Select button.
Press the Menu button to exit.

NOTE: A reading of 0H on the lamp usage timer means you’ve used less than 10 hours of lamp time.

Tips for extending Epson ELPLP39 lamp life

Get more hours from your Epson ELPLP39 lamp by following these maintenance tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson PowerLite Home Cinema 1080 UB projector and let it stand unused for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.

Learn more with Top tips for extending DLP projector lamp life.

Tagged with: authentic lamps, authentic projector lamps, Epson ELPLP39 lamp, Epson Powerlite Home Cinema 1080 UB, Epson projector lamps, genuine lamps, genuine projector lamps, how to replace Epson projector lamps, installation, lamp, Lamp replacement, Projector LAMP, replacement lamps, replacement projector lamps

Hassle-free instructions on replacing the Epson EMP-TW700 lamp

Shelagh McNallyPosted on January 30, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Wondering when and how to change the lamp in your Epson EMP-TW700 projector? Follow this handy step-by-step manual for a quick and easy installation!

Step 1: Be prepared

Knowing when to replace the Epson ELPLP39 lamp is the first step! Lamp life for the Epson EMP-TW700 will vary according to how much the projector is used. The replacement warning is set to appear after 1600 hours of lamp usage. In order to maintain the brightness and clarity of the projected images, do not use the lamp past the allocated time. Using it past it’s recommended time increases the risk of explosion.

Warning signs

Watch for the warning signs that the Epson ELPLP39 needs to be replaced:

the lamp warning on the projector started to blink red and continues blinking
the picture gets darker and continues to deteriorate
the message “Replace the lamp” appears on screen when the projector is turned on.

Step 2: Get the right lamp ready

Replace the Epson ELPLP39 lamp with a guaranteed authentic lamp. Look for the seal of approval to verify your Epson ELPLP39 lamp is authentic and buy from an authorized manufacturer.

If the price of the lamp you’re about to buy seems like an incredible bargain, chances are it’s counterfeit and has been created using inferior parts that damage the inside of your Epson EMP-TW700 projector. Generic lamps also come with a health risk; since copycat manufacturers can’t get the proper materials they often using highly toxic substitutes.

Buying a knock-off lamp will also void your warranty and should anything happen to the projector you will not be covered. Go with an authentic Epson ELPLP39 — it’s worth the few extra dollars to save yourself problems.

Step 3: Installing the Epson ELPLP39

Before opening up the Epson EMP-TW700 to install the lamp, follow these steps:

press the power button and wait for the light to stop flashing.
turn off the power switch at the back on the projector
unplug any power cords to cables to prevent the projector from accidentally being turned on.
give the projector one full hour to cool. The Epson EMP-TW700 operates on high heat and you will burn yourself if the projector has not cooled down.

Gently press on the EMP-TW700 lamp cover. Slide it away from the projector and then lift up to remove.

Using the screw driver provided, locate the two screws holding the Epson ELPLP39 lamp in place. Loosen both screws (they will not come out of the lamp altogether).

Grab the handle on the Epson ELPLP39 and gently pull the lamp up. Pulling too quickly can break the glass bulb. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP39 CAN’T be thrown into regular garbage! Since it contains mercury and should not be properly recycled! Your authorized manufacturer will recycle the lamp for you at no extra cost. (Another reason to go with authentic lamps!)

Line up the Epson ELPLP39 lamp and gently lower it into the EMP-TW700 projector.

Line up the EMP-TW700 cover hinges with the projector and place the lamp cover into them. Slide the lamp cover back down and click it into place. You’re now ready to reset the lamp operating timer.

Resetting the Lamp Operating Timer

To reset the Lamp Operating Timer:

Plug the power cord back into the projector
Press the on button and wait for the projector to warm up.
Press the MENU button to display the CONFIGURATION MENU.
Scroll down to select RESET menu.
Scroll down and choose RESET LAMP HOURS option
Press ENTER.
The reset lamp hour message will show up.

Select YES
Press ENTER.
Lamp hours will be set to zero.

Extending the Epson ELPLP39 lamp life

Get more hours from your Epson ELPLP39 lamp by following these maintenance tips:

To avoid overhearing the projector and causing the lamp to explode, keep the air filters clean.
Let the Epson EMP-TW700 rest for at least one hour per day.
Using it only our to five hours per day will give the lamp a longer life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted. Overheating can cause lamp failure.

Learn more with Top tips for extending DLP projector lamp life.

Tagged with: authentic lamps, authentic projector lamps, Epson ELPLP39 lamp, Epson EMP-TW700, Epson projector lamps, genuine lamps, genuine projector lamps, how to replace Epson projector lamps, installation, Lamp replacement, Projector LAMP, replacement lamps, replacement projector lamps, troubleshooting

Replacing your Epson PowerLite Home Cinema 1080 lamp

Shelagh McNallyPosted on January 30, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Replacing the Epson ELPLP39 lamp in your Epson PowerLite Home Cinema 1080 projector doesn’t have to be a complicated endeavour. Our 3-step guide outlines what to do for a quick replacement.

Step 1: How do I know when to replace?

the projected image get darker
the warning lamp on the projector flashes red and then continues to flash every half-second
the message: “Replace the lamp” flashes on the screen when you start using the projector.

Step 2: Buying the best lamp

It can be overwhelming shopping for a new Epson ELPLP39 on the Internet. There are so many choices and unfortunately many of the sites, including some of the big name online retailers, are selling knock-off lamps.

These “generic” lamps are sold at discount prices and investigation reveals these lamps are actually dangerous to use. They have been created with toxic substances such as Krypton-85, known to cause cancer. Would you compromise your health and risk your eyesight for the sake of a few dollars?

Since these copy cat lamps have been created without proper calibrating, they can also damage the sensitive imaging electronics in your Epson PowerLite Home Cinema 1080. They are also prone to explosions and have a much shorter life. When you buy authentic you’ll be getting a guarantee with your lamp and keeping your warranty valid. Look for the seal of approval and buy from an authentic manufacturer.

Learn how to protect yourself from counterfeit manufacturers.

Step 3: Installing the Epson ELPLP39

Pre-installation preparations:

let the projector cool for one full hour before trying to replace the lamp. This projector operates under very high temperatures and will be very hot. You can suffer burns if you are change the lamp while the projector is still hot. too impatient to wait until the projector is cool enough.
press the power button and wait for the light to stop flashing.
turn off the power switch at the back on the projector
unplug any power cords to cables to prevent the projector from accidentally being turned on. running the projector without a lamp will damage the projector.

Press the latches holding the PowerLite Home Cinema 1080 lamp cover in place. Gently lift off the cover and place it to one side.

Using the screw driver provided, loosen the two screws securing the Epson ELPLP39 lamp. They won’t come all the way out so simply loosen them enough so the lamp can be lifted out.

Grab the bottom of the Epson ELPLP39 lamp and pull it up with a straight motion. Be sure to properly dispose of the old lamp. Do not throw it into regular garbage as it contains mercury.

Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

Gently line up the new Epson ELPLP39 lamp and slide it into place. Make sure not to touch the glass portion of the lamp. The oil on your fingers may cause the lamp to stop before its time.

Tighten the screws on the Epson ELPLP39 lamp.

Replace the PowerLite Home Cinema 1080 lamp cover making sure it’s clicked into place. Otherwise, the projector will not turn on. You are now ready to reset the Lamp Usage Timer.

Reset the Lamp Usage Timer

It’s important to reset the Lamp Usage Timer so the Epson PowerLite Home Cinema 1080 projector will know when it’s time for a new Epson ELPLP39 lamp. Resetting the timer before installing a new Epson ELPLP39 can cause serious damage to your projector.

Plug the projector back in.
Turn on the power switch on
Press the Power button and wait for the Epson Home Cinema 108o to warm up.
Press the Menu button on either the projector or remote control.
Scroll down to the Reset menu option.
Select Reset Hours.
A confirmation message will appear asking if you want to reset the hours Click on yes.
Press the Select button.
Press the Menu button to exit.

NOTE: A reading of 0H on the lamp usage timer means you’ve used less than 10 hours of lamp time.

Tips for extending Epson ELPLP39 lamp life

Get more hours from your Epson ELPLP39 lamp by following these maintenance tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson PowerLite Home Cinema 1080 projector and let it stand unused for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life.

Tagged with: authentic lamps, authentic projector lamps, Epson ELPLP39 lamp, Epson ELPLP39 projector lamp, Epson Home Cinema 1080 projector, Epson projector lamps, genuine lamps, genuine projector lamps, how to replace Epson projector lamps, installation, lamp, Lamp replacement, Projector LAMP, replacement lamps, replacement projector lamps

Hassle free instructions for replacing the Epson H281A projector lamp

Shelagh McNallyPosted on January 25, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — 2 Comments ↓

Replacing the Epson H281A projector lamp can be hassle-free.

The Epson H281A projector lamp will last up to 2900 hours at high brightness and close to 3900 hours at low brightness before needing to be replaced. Watch for warning signs that the Epson H281A projector lamp needs to be replaced

End of life warnings

Watch for the warning signs that the Epson H281A projector lamp needs replacing:

Dark image
Image that has deteriorated
On warning message appears on screen
Lamp light flashes orange

Authentic vs generic lamps

The Internet has been flooded with many different choices for lamps. Unfortunately many are not authentic lamps and have been created by copycat manufacturers. It can be tempting to go with a “generic” compatible lamp offered at a discount price. Who doesn’t love a bargain? Unfortunately, these lamps will end up costing you more in the long run.

In order to keep your Epson H281A projector lamp working at its optimum levels and to prevent damage, you’ll want to buy an authentic projector lamp. When you buy from an authorized dealer, you’ll be getting a lamp that has been manufactured to the specifications of your projector.

Why avoid generics:

generic have a much shorter lamp life than OEM lamps
copycat lamps are often created with toxic materials and carcinogenic parts including Krypton-85
compatible lamps are prone to explosions
generic lamps are not calibrated properly and can the sensitive electronics in projectors
copycat manufacturers offer no guarantee or refunds
the warranty on your Epson H281A projector lamp will become void.

Learn how to spot the copycat fake lamps with 7 Ways to Spot a Counterfeit Lamp.

Buy this lamp on Amazon sold by these authorized dealers:

Installing the Epson H281A projector lamp

Before installation:

Turn off power switch on the back of the Epson H281A projector.
After you turn off the projector’s power and the confirmation buzzer beeps twice, disconnect the power cable
Allow the Epson H281A projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

1. The lamp cover is found on top of the Epson H281A projector. Loosen the lamp cover screw — you can’t remove it only loosen it.

2. Slide the Epson H281A projector lamp cover off.

3. Loosen the two screws holding the Epson ELPLP42 lamp in place.

4. Grab the Epson H281A projector lamp by the two indents on the lamp. Gently remove the lamp. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP42 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps! If you bought from an authentic manufacturer they will recycle the lamp for you at no extra cost (another reason to buy authentic lamps).

5. Gently insert the Epson ELPLP42 lamp making sure it’s facing the right way.

NOTE: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

6. Tighten the screws on the new Epson ELPLP42 lamp.

7. Replace the Epson H281A projector lamp lamp cover and tighten the screw on the Epson H281A projector lamp cover.

8. Reset the lamp timer.

Reset the lamp timer on the Epson H281A projector

Reset the Epson H281A projector Lamp Replacement Counter only when the Epson ELPLP42 lamp has been replaced.

Press the MENU button on the remote control. The Lamp Reset Menu will appear.
Scroll down to the RESET. Press ENTER.
Click on RESET ALL.
A prompt appears asking if you want to replace the lamp.
Select YES and press ENTER.
Press MENU to exit.

Prolong the life of the Epson ELPLP42 lamp:

Extend the life of the newly installed Epson ELPLP42 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson H281A projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life

Tagged with: authentic lamps, authentic projector lamps, Epson ELPLP42 lamp, Epson H281A projector, Epson projector lamps

Your D.I.Y. guide to a new Epson EX-90 projector lamp

Shelagh McNallyPosted on January 25, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Follow this handy guide in order to replace Epson EX-90 projector lamp

Replace the Epson EX-90 in three easy steps.

End of life warning signs

Watch for the signs that the Epson EX-90 projector lamp needs to be replaced:

Dark image
Image that has deteriorated
On warning message appears on screen
Lamp light flashes orange

Why buy an authentic lamp?

The Internet has been flooded with companies offering “generic” compatible lamps. Although they seem like a bargain, these lamps are actually not good for your Epson EX-90 projector lamp:

generic have a much shorter lamp life than OEM lamps
copycat lamps are often created with toxic materials and carcinogenic parts including Krypton-85
compatible lamps are prone to explosions
generic lamps are not calibrated properly and can the sensitive electronics in projectors
copycat manufacturers offer no guarantee or refunds
the warranty on your Epson EX-90 projector will become void.

Be sure the purchase an authentic Epson ELPLP42 to protect your health and the safety of your Epson EX-90 projector. Read more about the 7 Ways to Spot a Counterfeit Lamp.

Buy this lamp on Amazon sold by these authorized dealers:

Install the Epson Epson EX-90 projector lamp

Before installation:

Turn off power switch on the back of the Epson EX-90 projector.
After you turn off the projector’s power and the confirmation buzzer beeps twice, disconnect the power cable
Allow the Epson EX-90 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

1. The lamp cover is found on top of the Epson EX-90 projector. Loosen theEpson EX-90 projector lamp cover screw — you can’t remove it only loosen it.

2. Slide the Epson EX-90 projector lamp cover off.

3. Loosen the two screws holding the Epson ELPLP42 lamp in place.

4. Grab the Epson ELPLP42 lamp by the two indents on the lamp. Gently remove the lamp. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

5. Gently insert the Epson ELPLP42 lamp making sure it’s facing the right way.

NOTE: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

6. Tighten the screws on the new Epson ELPLP42 lamp.

7. Replace the lamp cover and tighten the screw on the Epson EX-90 projector lamp cover.

8. Reset the lamp timer.

Reset the lamp timer on the Epson EX-90 projector

Reset the Epson EX-90 projector Lamp Replacement Counter only when the Epson ELPLP42 lamp has been replaced.

Press the MENU button on the remote control. The Lamp Reset Menu will appear.
Scroll down to the RESET. Press ENTER.
Click on RESET ALL.
A prompt appears asking if you want to replace the lamp.
Select YES and press ENTER.
Press MENU to exit.

Prolong the life of the Epson ELPLP42 lamp:

Extend the life of the newly installed Epson ELPLP42 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson EX-90 projector projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life

Tagged with: authentic lamps, authentic projector lamps, Epson ELPLP42 lamp, Epson EX-90 projector, Epson projector lamps

Changing the Epson V11H285620 projector lamp

Shelagh McNallyPosted on January 22, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Wondering when it’s time to replace the lamp in your Epson V11H285620 projector? Follow our step-by-step guide.

When it’s time to replace the Epson ELPLP41 in the Epson V11H285620, you’ll see the following warning signs:

Dark image
Image that has deteriorated
On warning message appears on screen
Lamp light flashes orange
Lamp light turns red and stays on
Check Lamp Usage

You can expect up to the 3000 hours of use with the Epson ELPLP41 before it needs to be replaced, if you have installed an authentic lamp.

The importance of authentic lamps

It’s critical to install a genuine Epson ELPLP41 rather than a compatible generic lamps. Although lower in price initially, generic, knock-off lamps end up costing much more in the long run. Counterfeit generic lamp have a shorter lamp life, damage the components in your projector, have poor picture quality and are prone to explosion. You also run the risk of being exposed to the carcinogenic substances such Krypton-85used in the making of these lamps.

Be sure the purchase an authentic Epson ELPLP41 projector lamp for your Epson PowerLite Home Cinema 700 projector. Save yourself unnecessary headaches and buy authentic from a recognized dealer. You’ll be getting a far superior product with a replacement guarantee and tech support.

Read more about the 7 Ways to Spot a Counterfeit Lamp.

Installing the Epson ELPLP41

Before installation:

Turn power button off wait for light to stop flashing.
Turn off power on Epson V11H285620 projector.
Unplug the power cord.
Allow the Epson V11H285620 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

The lamp cover is found on top of the Epson V11H285620 projector. Loosen the lamp cover screw — you can’t remove it only loosen it.

Slide the Epson V11H285620 lamp cover off.

Loosen the two screws holding the Epson ELPLP41 lamp in place.

Grab the Epson ELPLP41 lamp by the two indents on the lamp. Gently remove the lamp.

Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP41 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps! If you bought from an authentic manufacturer they will recycle the lamp for you at no extra cost (another reason to buy authentic lamps).

Gently insert the Epson ELPLP41 lamp making sure it’s facing the right way.

Tighten the screws on the new Epson ELPLP41 lamp.

Replace the lamp cover and tighten the screw on the Epson V11H285620 lamp cover.
You are now ready to reset the lamp timer.

Reset the lamp timer on the Epson V11H285620

Reset the Epson V11H285620 Lamp Replacement Counter only when the Epson ELPLP41 lamp has been replaced.

Press the MENU button on the remote control. The Lamp Reset Menu will appear.
Scroll down to the RESET LAMP HOURS. Press ENTER.
A prompt appears asking if you want to replace the lamp.
Select YES and press ENTER.
Press MENU to exit.

Prolong the life of the Epson ELPLP41 lamp:

Extend the life of the newly installed Epson ELPLP41 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson V11H285620 projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life

Tagged with: authentic lamps, authentic projector lamps, Epson ELPLP41, Epson projector lamps, Epson V11H285620 projector, genuine lamps, genuine projector lamps, how to replace Epson projector lamps, lamp, Lamp replacement, Projector LAMP, replacement lamps, replacement projector lamps, troubleshooting

Your D.I.Y guide to a new Epson EMP-280 projector lamp

Shelagh McNallyPosted on January 22, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Here’s your quick guide for replacing the Epson EMP-280 projector lamp

Watch for the signs that time to replace the Epson EMP-280 projector lamp

Dark image
Image that has deteriorated
Lamp warning message appears on screen
Lamp light flashes orange
Lamp light turns red and stays on
Check Lamp Usage

Buy authentic

Be sure the purchase an authentic Epson ELPLP42 projector lamp for your Epson EMP-280 projector. Save yourself unnecessary headaches and buy authentic from a recognized dealer. You’ll be getting a far superior product with a replacement guarantee and tech support.

Read more about the 7 Ways to Spot a Counterfeit Lamp.

Buy this lamp on Amazon sold by these authorized dealers:

Installing the Epson ELPLP42

Before installation:

Turn power button off wait for light to stop flashing.
Turn off power switch on the back of the Epson EMP-280 projector.
Unplug the power cord.
Allow the Epson EMP-280 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

1. The lamp cover is found on top of the Epson EMP-280 projector. Loosen the lamp cover screw — you can’t remove it only loosen it.

2. Slide the Epson EMP-280 projector lamp cover off.

3. Loosen the two screws holding the Epson ELPLP42 lamp in place.

4. Grab the Epson ELPLP42 lamp by the two indents on the lamp. Gently remove the lamp.

Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP41 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps! If you bought from an authentic manufacturer they will recycle the lamp for you at no extra cost (another reason to buy authentic lamps).

5. Gently insert the Epson ELPLP42 lamp making sure it’s facing the right way.

6. Tighten the screws on the new Epson ELPLP42 lamp.

7. Replace the lamp cover and tighten the screw on the Epson EMP-280 projector lamp cover.

8. Reset the lamp timer.

Reset the lamp timer on the Epson EMP-280 projector

Reset the Epson EMP-280 projector Lamp Replacement Counter only when the Epson ELPLP42 lamp has been replaced.

Press the MENU button on the remote control. The Lamp Reset Menu will appear.
Scroll down to the RESET LAMP HOURS. Press ENTER.
A prompt appears asking if you want to replace the lamp.
Select YES and press ENTER.
Press MENU to exit.

Prolong the life of the Epson ELPLP42 lamp:

Extend the life of the newly installed Epson ELPLP42 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson EMP-280 projector projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life

Tagged with: authentic lamps, authentic projector lamps, Epson ELPLP42 lamp, Epson EMP-280 projector

The fast and easy way to replace the Epson EMP-822 projector lamp

Shelagh McNallyPosted on January 22, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Follow our step-by-step guide to replace the Epson EMP-822 projector lamp.

Watch for the signs that the Epson EMP-822 projector lamp needs to be replaced. Symptoms include:

Dark image
Image that has deteriorated
On warning message appears on screen
Lamp light flashes orange
Lamp light turns red and stays on
Check Lamp Usage

Buy authentic

It’s critical to install a genuine Epson ELPLP42 rather than a compatible generic lamps. Although lower in price initially, generic, knock-off lamps end up costing much more in the long run. Counterfeit generic lamp have a shorter lamp life, damage the components in your projector, have poor picture quality and are prone to explosion. You also run the risk of being exposed to the carcinogenic substances such Krypton-85 used in the making of these lamps.

Buy this lamp on Amazon sold by these authorized dealers:

6 reasons to avoid generic lamps:

Be sure the purchase an authentic Epson ELPLP42 projector lamp for your Epson EMP-822 projector. Save yourself unnecessary headaches and buy authentic from a recognized dealer. You’ll be getting a far superior product with a replacement guarantee and tech support.

Read more about the 7 Ways to Spot a Counterfeit Lamp.

Buy this lamp on Amazon sold by these authorized dealers:

Install the new lamp

Before installation:

Turn power button off wait for light to stop flashing.
Turn off power swtitch on the back of the Epson EMP-822 projector.
Unplug the power cord.
Allow the Epson EMP-822 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

1. The lamp cover is found on top of the Epson EMP-822 projector. Loosen the lamp cover screw — you can’t remove it only loosen it.

2. Slide the Epson EMP-822 projector lamp cover off.

3. Loosen the two screws holding the Epson ELPLP42 lamp in place.

4. Grab the Epson ELPLP42 lamp by the two indents on the lamp. Gently remove the lamp.

Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

5. Gently insert the Epson ELPLP42 lamp making sure it’s facing the right way.

6. Tighten the screws on the new Epson ELPLP42 lamp.

7. Replace the lamp cover and tighten the screw on the Epson EMP-822 projector lamp cover.

8. Reset the lamp timer.

Reset the lamp timer on the Epson EMP-822 projector

Reset the Epson EMP-822 projector Lamp Replacement Counter only when the Epson ELPLP42 lamp has been replaced.

Press the MENU button on the remote control. The Lamp Reset Menu will appear.
Scroll down to the RESET LAMP HOURS. Press ENTER.
A prompt appears asking if you want to replace the lamp.
Select YES and press ENTER.
Press MENU to exit.

Prolong the life of the Epson ELPLP42 lamp:

Extend the life of the newly installed Epson ELPLP42 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson EMP-822 projector projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life

Tagged with: authentic lamps, authentic projector lamps, Epson ELPLP42 lamp, Epson EMP-822, Epson projector lamps