About Us - Page 88 of 171 - DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP

Your guide to replacing the Epson EMP-83He projector lamp

Shelagh McNallyPosted on January 22, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Replacing the Epson EMP-83He projector lamp is simple when you follow this handy 3-step guide.

The Epson EMP-83He projector lamp can last approximately 3000 hours of life using the HIGH brightness mode or close to 4000 hours if you have sent the brightness to low. Be sure to buy an authentic Epson EMP-83He projector lamp and have that ready before proceeding.

Step 1: Knowing when to replace the lamp

Watch for the signs that the Epson ELPLP42 needs to be replaced in the Epson EMP-83He projector:

Dark image
Image that has deteriorated
On warning message appears on screen
Lamp light flashes orange

Step 2: Buying the correct lamp

Why buy an authentic lamp that is more expensive?
The Internet has been flooded with companies offering “generic” compatible lamps. Although they seem like a bargain, these lamps are actually not good for your Epson EMP-83H projector. They can seriously damage your projector and cost you more money.

6 good reasons for buying authentic lamps:

generic have a much shorter lamp life than OEM lamps
copycat lamps are often created with toxic materials and carcinogenic parts including Krypton-85
compatible lamps are prone to explosions
generic lamps are not calibrated properly and can the sensitive electronics in projectors
copycat manufacturers offer no guarantee or refunds
the warranty on your Epson EMP-83He projector will become void.

Be sure the purchase an authentic Epson ELPLP42 to protect your health and the safety of your Epson EMP-83He projector. Read more about the 7 Ways to Spot a Counterfeit Lamp.

Buy this lamp on Amazon sold by these authorized dealers:

Step 3: Install the Epson ELPLP42

Before installation:

Turn off power switch on the back of the Epson EMP-83He projector.
After you turn off the projector’s power and the confirmation buzzer beeps twice, disconnect the power cable
Allow the Epson EMP-83He projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

1. The lamp cover is found on top of the Epson EMP-83He projector. Loosen the lamp cover screw — you can’t remove it only loosen it.

2. Slide the Epson EMP-83He projector lamp cover off.

3. Loosen the two screws holding the Epson ELPLP42 lamp in place.

4. Grab the Epson ELPLP42 lamp by the two indents on the lamp. Gently remove the lamp. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP42 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps! If you bought from an authentic manufacturer they will recycle the lamp for you at no extra cost (another reason to buy authentic lamps).

5. Gently insert the Epson ELPLP42 lamp making sure it’s facing the right way.

NOTE: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

6. Tighten the screws on the new Epson ELPLP42 lamp.

Epson-EMP-83He-replace-cover-Epson-ELPLP42-lamp

7. Replace the lamp cover and tighten the screw on the Epson EMP-83He projector lamp cover.

8. Reset the lamp timer.

Reset the lamp timer on the Epson EMP-83He projector

Reset the Epson EMP-83He projector Lamp Replacement Counter only when the Epson ELPLP42 lamp has been replaced.

Press the MENU button on the remote control. The Lamp Reset Menu will appear.
Scroll down to the RESET. Press ENTER.
Click on RESET ALL.
A prompt appears asking if you want to replace the lamp.
Select YES and press ENTER.
Press MENU to exit.

Prolong the life of the Epson ELPLP42 lamp:

Extend the life of the newly installed Epson ELPLP42 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson EMP-83He projector projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life

How to replace your Epson EB-400We projector lamp

Shelagh McNallyPosted on January 21, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Take these 3 steps to install a Epson EB-400We projector lamp

Hassle free instructions for replacing your Epson EB-400We projector lamp. You’ll need a Epson ELPLP42 bought from an authorized dealer.

Buy this lamp on Amazon sold by these authorized dealers:

Step 1: Lamp hour notifications

Watch for the signs that the Epson ELPLP42 needs to be replaced in the Epson EB-400We projector:

Dark image
Image that has deteriorated
On warning message appears on screen
Lamp light flashes orange

Step 2: Buy your lamp

There are a lot of choices for your Epson ELPLP42 lamp but only one correct lamp to buy. In order to keep your Epson EB-400We working at its optimum levels and to prevent damage, you’ll want to buy an authentic projector lamp. Internet is flooded with companies offering “generic” compatible lamps. Although they seem like a bargain, these should be avoided. They have some very serious flaws:

generic have a much shorter lamp life than OEM lamps
copycat lamps are often created with toxic materials and carcinogenic parts including Krypton-85
compatible lamps are prone to explosions
generic lamps are not calibrated properly and can the sensitive electronics in projectors
copycat manufacturers offer no guarantee or refunds
the warranty on your Epson EB-400We projector will become void.

Learn how to spot the copycat fake lamps with 7 Ways to Spot a Counterfeit Lamp.

Step 3: Install the Epson ELPLP42

Before installation:

Turn off power switch on the back of the Epson EB-400We projector.
After you turn off the projector’s power and the confirmation buzzer beeps twice, disconnect the power cable
Allow the Epson EB-400We projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

1. The lamp cover is found on top of the Epson EB-400We projector. Loosen the lamp cover screw — you can’t remove it only loosen it.

2. Slide the Epson EB-400We projector lamp cover off.

3. Loosen the two screws holding the Epson ELPLP42 lamp in place.

4. Grab the Epson ELPLP42 lamp by the two indents on the lamp. Gently remove the lamp. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP42 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

5. Gently insert the Epson ELPLP42 lamp making sure it’s facing the right way. NOTE: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

6. Tighten the screws on the new Epson ELPLP42 lamp.

7. Replace the lamp cover and tighten the screw on the Epson EB-400We projector lamp cover.

8. Reset the lamp timer.

Reset the lamp timer

Reset the Epson EB-400We projector Lamp Replacement Counter only when the Epson ELPLP42 lamp has been replaced.

Press the MENU button on the remote control. The Lamp Reset Menu will appear.
Scroll down to the RESET. Press ENTER.
Click on RESET ALL.
A prompt appears asking if you want to replace the lamp.
Select YES and press ENTER.
Press MENU to exit.

Prolong the life of the Epson ELPLP42 lamp:

Extend the life of the newly installed Epson ELPLP42 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson EB-400We projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life

Tagged with: authentic lamps, authentic projector lamps, Epson EB-400We, Epson ELPLP42 lamp, Epson projector lamps

Replacing the Epson EB-400W projector lamp

Shelagh McNallyPosted on January 21, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Epson-EMP-410W-projector-Epson-ELPLP42-lamp

Replacing the Epson EB-400W projector lamp is hassle-free when you follow our guide

You can expect close to 2900 hours at high brightness and close to 3900 hours at low brightness from the Epson EB-400W projector lamp.

Watch for the warning signs that the Epson ELPLP42 needs to be replaced in the Epson EB-400W projector:

Dark image
Image that has deteriorated
On warning message appears on screen
Lamp light flashes orange

Authentic vs generic lamps

The Internet has been flooded with many different choices for lamps. Unfortunately many are not authentic lamps and have been created by copycat manufacturers. It can be tempting to go with a “generic” compatible lamp offered at a discount price. Who doesn’t love a bargan? Unfortunately, these lamps will end up costing you more in the long run.

In order to keep your Epson EB-400W working at its optimum levels and to prevent damage, you’ll want to buy an authentic projector lamp. When you buy from an authorized dealer, you’ll be getting a lamp that has been manufactured to the specifications of your projector.

Why avoid generics:

generic have a much shorter lamp life than OEM lamps
copycat lamps are often created with toxic materials and carcinogenic parts including Krypton-85
compatible lamps are prone to explosions
generic lamps are not calibrated properly and can the sensitive electronics in projectors
copycat manufacturers offer no guarantee or refunds
the warranty on your Epson EB-400W projector will become void.

Learn how to spot the copycat fake lamps with 7 Ways to Spot a Counterfeit Lamp.

Buy this lamp on Amazon sold by these authorized dealers:

Installing the Epson ELPLP42

Before installation:

Turn off power switch on the back of the Epson EB-400We projector.
After you turn off the projector’s power and the confirmation buzzer beeps twice, disconnect the power cable
Allow the Epson EB-400W projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

1. The lamp cover is found on top of the Epson EB-400W projector. Loosen the lamp cover screw — you can’t remove it only loosen it.

2. Slide the Epson EB-400W projector lamp cover off.

3. Loosen the two screws holding the Epson ELPLP42 lamp in place.

4. Grab the Epson ELPLP42 lamp by the two indents on the lamp. Gently remove the lamp. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP42 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

6. Tighten the screws on the new Epson ELPLP42 lamp.

7. Replace the lamp cover and tighten the screw on the Epson EB-400W projector lamp cover.

8. Reset the lamp timer.

Reset the lamp timer

Reset the Epson EB-400W projector Lamp Replacement Counter only when the Epson ELPLP42 lamp has been replaced.

Press the MENU button on the remote control. The Lamp Reset Menu will appear.
Scroll down to the RESET. Press ENTER.
Click on RESET ALL.
A prompt appears asking if you want to replace the lamp.
Select YES and press ENTER.
Press MENU to exit.

Prolong the life of the Epson ELPLP42 lamp:

Extend the life of the newly installed Epson ELPLP42 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson EB-400W projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life

Tagged with: authentic lamps, Epson EB-400W projector, Epson ELPLP42 lamp, Epson projector lamps

3 Steps to a new Epson EB-410We projector lamp

Shelagh McNallyPosted on January 21, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Wondering when to replace the Epson EB-410We projector lamp?

Follow this 3-step guide for a quick and easy Epson EB-410We projector lamp replacement.

Step 1: Know when to replace

Watch for the warning signs that it’s time to replace the Epson ELPLP42 projector lamp.
You can expect close to 2900 hours at high brightness and close to 3900 hours at low brightness.

Watch for the warning signs that the Epson ELPLP42 needs to be replaced in the Epson EB-410We projector:

Dark image
Image that has deteriorated
On warning message appears on screen
Lamp light flashes orange

Step 2: Buying the correct lamp

The Internet has been flooded with many different choices for lamps. Unfortunately many are not authentic lamps and have been created by copycat manufacturers.

In order to keep your Epson EB-410We working at its optimum levels and to prevent damage, you’ll want to buy an authentic projector lamp. The Internet is flooded with companies offering “generic” compatible lamps. Although they seem like a bargain, these should be avoided. They have some very serious flaws.

6 reasons for avoiding generic lamps:

generic have a much shorter lamp life than OEM lamps
copycat lamps are often created with toxic materials and carcinogenic parts including Krypton-85
compatible lamps are prone to explosions
generic lamps are not calibrated properly and can the sensitive electronics in projectors
copycat manufacturers offer no guarantee or refunds
the warranty on your Epson EB-410We projector will become void.

Learn how to spot the copycat fake lamps with 7 Ways to Spot a Counterfeit Lamp.

Buy this lamp on Amazon sold by these authorized dealers:

Step 3: Installing the Epson ELPLP42

Before installation:

Turn off power switch on the back of the Epson EB-410We projector.
After you turn off the projector’s power and the confirmation buzzer beeps twice, disconnect the power cable
Allow the Epson EB-410We projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

1. The lamp cover is found on top of the Epson EB-410We projector. Loosen the lamp cover screw — you can’t remove it only loosen it.

2. Slide the Epson EMP-410We projector lamp cover off.

3. Loosen the two screws holding the Epson ELPLP42 lamp in place.

4. Grab the Epson ELPLP42 lamp by the two indents on the lamp. Gently remove the lamp. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP42 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

6. Tighten the screws on the new Epson ELPLP42 lamp.

7. Replace the lamp cover and tighten the screw on the Epson EB-410We projector lamp cover.

8. Reset the lamp timer.

Reset the lamp timer

Reset the Epson EB-410We projector Lamp Replacement Counter only when the Epson ELPLP42 lamp has been replaced.

Press the MENU button on the remote control. The Lamp Reset Menu will appear.
Scroll down to the RESET. Press ENTER.
Click on RESET ALL.
A prompt appears asking if you want to replace the lamp.
Select YES and press ENTER.
Press MENU to exit.

Prolong the life of the Epson ELPLP42 lamp:

Extend the life of the newly installed Epson ELPLP42 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson EB-410We projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life

Tagged with: authentic lamps, authentic projector lamps, Epson EB-410We projector, Epson projector lamps

How to replace the Epson EB-410W projector lamp

Shelagh McNallyPosted on January 21, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Follow this step-by-step guide to replace Epson EB-410W projector lamp

Watch for the warning signs that it’s time to replace the Epson EB-410W projector lamp.

Dark image
Image that has deteriorated
On warning message appears on screen
Lamp light flashes orange

You can expect close to 2900 hours at high brightness and close to 3900 hours at low brightness.

Authentic vs generic lamps

The Internet has been flooded with many different choices for lamps. Unfortunately many are not authentic lamps and have been created by copycat manufacturers.

In order to keep your Epson EB-410W working at its optimum levels and to prevent damage, you’ll want to buy an authentic projector lamp. The Internet is flooded with companies offering “generic” compatible lamps. Although they seem like a bargain, these should be avoided. They have some very serious flaws:

generic have a much shorter lamp life than OEM lamps
copycat lamps are often created with toxic materials and carcinogenic parts including Krypton-85
compatible lamps are prone to explosions
generic lamps are not calibrated properly and can the sensitive electronics in projectors
copycat manufacturers offer no guarantee or refunds
the warranty on your Epson EB-410W projector will become void.

Learn how to spot the copycat fake lamps with 7 Ways to Spot a Counterfeit Lamp.

Buy this lamp on Amazon sold by these authorized dealers:

Installing the Epson ELPLP42

Before installation:

Turn off power switch on the back of the Epson EB-410W projector.
After you turn off the projector’s power and the confirmation buzzer beeps twice, disconnect the power cable
Allow the Epson EB-410W projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

1. The lamp cover is found on top of the Epson EB-410W projector. Loosen the lamp cover screw — you can’t remove it only loosen it.

2. Slide the Epson EMP-410W projector lamp cover off.

3. Loosen the two screws holding the Epson ELPLP42 lamp in place.

4. Grab the Epson ELPLP42 lamp by the two indents on the lamp. Gently remove the lamp. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP42 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

6. Tighten the screws on the new Epson ELPLP42 lamp.

7. Replace the lamp cover and tighten the screw on the Epson EB-410W projector lamp cover.

8. Reset the lamp timer.

Reset the lamp timer

Reset the Epson EB-410W projector Lamp Replacement Counter only when the Epson ELPLP42 lamp has been replaced.

Press the MENU button on the remote control. The Lamp Reset Menu will appear.
Scroll down to the RESET. Press ENTER.
Click on RESET ALL.
A prompt appears asking if you want to replace the lamp.
Select YES and press ENTER.Press MENU to exit.

Prolong the life of the Epson ELPLP42 lamp:

Extend the life of the newly installed Epson ELPLP42 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson EB-410W projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life

Tagged with: authentic lamps, Epson EB-410W projector, Epson ELPLP42 lamp, Epson ELPLP49 projector lamp

Replacing the Epson EMP-410WE projector lamp

Shelagh McNallyPosted on January 18, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

This 3-step guide will help you install a new Epson EMP-410WE projector lamp

The life span of the Epson EMP-410WE projector lamp ranges from approximately 3000 hours in HIGH brightness mode to about 4000 hours in LOW brightness mode.

Step 1: When to replace

Find the exact hours the lamp has been used on the Info Menu. If the number of hours is under 10, the time will be displayed as 0H.

Watch for the signs that the Epson ELPLP42 needs to be replaced in the Epson EMP-410WE projector:

Dark image
Image that has deteriorated
Replace the Lamp message appears on screen
Lamp light flashes orange

Step 2: Buy authentic

It’s critical to install a genuine Epson ELPLP42 rather than a compatible generic lamps. Although lower in price initially, generic, knock-off lamps end up costing much more in the long run. Generic have so many problems, they actually end up costing more in the end.

6 reasons to avoid generic lamps:

shorter lamp life than original lamps
created toxic materials and carcinogenic parts including Krypton-85
prone to explosions
incompatibility causing damage to the sensitive electronics in your projectors
no guarantee or refunds
the warranty will become void on your Epson EMP-410WE projector.

Be sure the purchase an authentic Epson ELPLP42 projector lamp for your Epson EMP-410WE projector. Save yourself unnecessary headaches and buy authentic from a recognized dealer. You’ll be getting a far superior product with a replacement guarantee and tech support.

Read more about the 7 Ways to Spot a Counterfeit Lamp.

Buy this lamp on Amazon sold by these authorized dealers:

Step 3: Install the Epson ELPLP42

Before installation:

Turn power button off and wait for light to stop flashing.
Turn off power swtich on the back of the Epson EMP-410WE projector.
Unplug the power cord.
Allow the Epson EMP-410WE projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

1. Using the screw driver supplied, loosen the screw holding the Epson EMP-410WE cover in place.

2. Remove the Epson EMP-410WE lamp cover and place it to one side.

3. Using the screw driver provided, loosen the screws holding the Epson ELPLP42 lamp in place.

4. Grab the Epson ELPLP42 lamp by the two indents on the lamp. Gently remove the lamp.Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP42 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

5. Gently insert the Epson ELPLP42 lamp making sure it’s facing the right way. It should click easily into place. Do not force the lamp into the projector as you may break the light. Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

Tighten the screws on the newly installed Epson ELPLP42 lamp. Be sure not to tighten the screw too much or leave the screw too loose as this can stop the newly installed lamp from working.

Replace the Epson EMP-410WE lamp cover and tighten the screw. You are now ready to reset the Lamp Timer.

Reset the lamp timer

Reset the Epson EMP-410WE projector Lamp Replacement Counter only when the Epson ELPLP42 lamp has been replaced.

Press the MENU button on the remote control. The Lamp Reset Menu will appear.
Scroll down to the RESET ALL. Press ENTER.
A prompt appears asking if you want to replace the lamp.
Select YES and press ENTER.
Press MENU to exit.

Prolong the life of the Epson ELPLP42 lamp:

Extend the life of the newly installed Epson ELPLP42 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson EMP-410WE projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life

Tagged with: authentic lamps, authentic projector lamps, Epson ELPLP42 lamp, Epson EMP-410WE projector, Epson projector lamps

Your guide to replacing the Epson EMP-410W projector lamp

Shelagh McNallyPosted on January 18, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Follow this quick guide to change the Epson EMP-410W projector lamp

The life span of the Epson EMP-410W projector lamp ranges from 3000 hours in HIGH brightness mode to about 4000 hours in LOW brightness mode.

When to replace

Find the exact hours the lamp has been used on the Info Menu. If the number of hours is under 10, the time will be displayed as 0H.

Watch for the signs that the Epson ELPLP42 needs to be replaced in the Epson EMP-410W projector:

Dark image
Image that has deteriorated
Replace the Lamp message appears on screen
Lamp light flashes orange

Buy authentic

6 reasons to avoid generic lamps:

shorter lamp life than original lamps
created toxic materials and carcinogenic parts including Krypton-85
prone to explosions
incompatibility causing damage to the sensitive electronics in your projectors
no guarantee or refunds
the warranty will become void on your Epson EMP-410W projector.

Be sure the purchase an authentic Epson ELPLP42 projector lamp for your Epson EMP-410W projector. Save yourself unnecessary headaches and buy authentic from a recognized dealer. You’ll be getting a far superior product with a replacement guarantee and tech support.

Read more about the 7 Ways to Spot a Counterfeit Lamp.

Buy this lamp on Amazon sold by these authorized dealers:

Install the Epson ELPLP42

Before installation:

Turn power button off and wait for light to stop flashing.
Turn off power swtich on the back of the Epson EMP-410W projector.
Unplug the power cord.
Allow the Epson EMP-410W projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

1. Using the screw driver supplied, loosen the screw holding the Epson EMP-410W cover in place.

2. Remove the Epson EMP-410W lamp cover and place it to one side.

3. Using the screw driver provided, loosen the screws holding the Epson ELPLP42 lamp in place.

4. Grab the Epson ELPLP42 lamp by the two indents on the lamp. Gently remove the lamp.Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP42 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

Tighten the screws on the newly installed Epson ELPLP42 lamp. Be sure not to tighten the screw too much or leave the screw too loose as this can stop the newly installed lamp from working.

Replace the Epson EMP-410W lamp cover and tighten the screw. You are now ready to reset the Lamp Timer.

Reset the lamp timer

Reset the Epson EMP-410W projector Lamp Replacement Counter only when the Epson ELPLP42 lamp has been replaced.

Press the MENU button on the remote control. The Lamp Reset Menu will appear.
Scroll down to the RESET ALL. Press ENTER.
A prompt appears asking if you want to replace the lamp.
Select YES and press ENTER.
Press MENU to exit.

Prolong the life of the Epson ELPLP42 lamp:

Extend the life of the newly installed Epson ELPLP42 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson EMP-410W projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life

Tagged with: authentic lamps, Epson ELPLP42 projector lamp, Epson EMP-410W projector, Epson projector lamps

3 Steps to a new Epson 400WE projector lamp

Shelagh McNallyPosted on January 18, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Change the Epson EMP-400WE projector lamp in three easy steps

Step 1: When to replace

Watch for the signs that the Epson ELPLP42 needs to be replaced in the Epson EMP-400WE projector:

Dark image
Image that has deteriorated
On warning message appears on screen
Lamp light flashes orange

Step 2: Buying the correct lamp

In order to keep your Epson EMP-400WE working at its optimum levels and to prevent damage, you’ll want to buy an authentic projector lamp. The Internet is flooded with companies offering “generic” compatible lamps. Although they seem like a bargain, these should be avoided. They have some very serious flaws.

6 reasons to avoid generic lamps

generic have a much shorter lamp life than OEM lamps
copycat lamps are often created with toxic materials and carcinogenic parts including Krypton-85
compatible lamps are prone to explosions
generic lamps are not calibrated properly and can the sensitive electronics in projectors
copycat manufacturers offer no guarantee or refunds
the warranty on your Epson EMP-400WE projector will become void.

Learn how to spot the copycat fake lamps with 7 Ways to Spot a Counterfeit Lamp.

Buy this lamp on Amazon sold by these authorized dealers:

Installing the Epson ELPLP42

Before installation:

Turn off power switch on the back of the Epson EMP-400WE projector.
After you turn off the projector’s power and the confirmation buzzer beeps twice, disconnect the power cable
Allow the Epson EMP-400WE projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

1. The lamp cover is found on top of the Epson EMP-400WE projector. Loosen the lamp cover screw — you can’t remove it only loosen it.

2. Slide the Epson EMP-400WE projector lamp cover off.

3. Loosen the two screws holding the Epson ELPLP42 lamp in place.

4. Grab the Epson ELPLP42 lamp by the two indents on the lamp. Gently remove the lamp. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP42 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

6. Tighten the screws on the new Epson ELPLP42 lamp.

7. Replace the lamp cover and tighten the screw on the Epson EMP-400WE projector lamp cover.

8. Reset the lamp timer.

Reset the lamp timer

Reset the Epson EMP-400WE projector Lamp Replacement Counter only when the Epson ELPLP42 lamp has been replaced.

Press the MENU button on the remote control. The Lamp Reset Menu will appear.
Scroll down to the RESET. Press ENTER.
Click on RESET ALL.
A prompt appears asking if you want to replace the lamp.
Select YES and press ENTER.
Press MENU to exit.

Prolong the life of the Epson ELPLP42 lamp:

Extend the life of the newly installed Epson ELPLP42 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson EMP-400WE projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life

Tagged with: authentic lamps, Epson ELPLP42, Epson ELPLP42 projector lamp, Epson EMP-400WE projector, replacement lamps

Your D.I.Y. guide to a new Epson EMP-83H projector lamp

Shelagh McNallyPosted on January 16, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — 6 Comments ↓

Follow this guide to replace the Epson EMP-83H projector lamp

Watch for the signs that Epson EMP-83H projector lamp needs replacing:

Dark image
Image that has deteriorated
On warning message appears on screen
Lamp light flashes orange

Why buy an authentic lamp?

The Internet has been flooded with companies offering “generic” compatible lamps. Although they seem like a bargain, these lamps are actually not good for your Epson EMP-83H projector:

generic have a much shorter lamp life than OEM lamps
copycat lamps are often created with toxic materials and carcinogenic parts including Krypton-85
compatible lamps are prone to explosions
generic lamps are not calibrated properly and can the sensitive electronics in projectors
copycat manufacturers offer no guarantee or refunds
the warranty on your Epson EMP-83H projector will become void.

Be sure the purchase an authentic Epson ELPLP42 to protect your health and the safety of your Epson EMP-83H projector. Read more about the 7 Ways to Spot a Counterfeit Lamp.

Buy this lamp on Amazon sold by these authorized dealers:

Install the Epson ELPLP42

Before installation:

Turn off power switch on the back of the Epson EMP-83H projector.
After you turn off the projector’s power and the confirmation buzzer beeps twice, disconnect the power cable
Allow the Epson EMP-83H projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

1. The lamp cover is found on top of the Epson EMP-83H projector. Loosen the lamp cover screw — you can’t remove it only loosen it.

2. Slide the Epson EMP-83H projector lamp cover off.

3. Loosen the two screws holding the Epson ELPLP42 lamp in place/

4. Grab the Epson ELPLP42 lamp by the two indents on the lamp. Gently remove the lamp. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP42 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

6. Tighten the screws on the new Epson ELPLP42 lamp.

Epson-EMP-83H-replace-cover-Epson-ELPLP42-lamp

7. Replace the lamp cover and tighten the screw on the Epson EMP-83H projector lamp cover.

8. Reset the lamp timer.

Reset the lamp timer

Reset the Epson EMP-83H projector Lamp Replacement Counter only when the Epson ELPLP42 lamp has been replaced.

Press the MENU button on the remote control. The Lamp Reset Menu will appear.
Scroll down to the RESET. Press ENTER.
Click on RESET ALL.
A prompt appears asking if you want to replace the lamp.
Select YES and press ENTER.Press MENU to exit.

Prolong the life of the Epson ELPLP42 lamp:

Extend the life of the newly installed Epson ELPLP42 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson EMP-83H projector projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life

Tagged with: authentic lamps, Epson ELPLP42 lamp, Epson EMP-83H projector, Projector LAMP

Changing the Epson EMP-822H projector lamp

Shelagh McNallyPosted on January 16, 2013 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Replacing Epson EMP-22H projector lamp is simple when you follow our guide.

Warning signs

Watch for signs that the Epson EMP-22H projector lamp needs to be replaced:

Dark image
Image that has deteriorated
On warning message appears on screen
Lamp light flashes orange

Buy authentic

The Internet has been flooded with companies offering “generic” compatible lamps. Although they seem like a bargain, these lamps are actually not good for your Epson EMP-822H projector. Here are six reasons for NOT buying generic lamps:

generic have a much shorter lamp life than OEM lamps
copycat lamps are often created with toxic materials and carcinogenic parts including Krypton-85
compatible lamps are prone to explosions
generic lamps are not calibrated properly and can the sensitive electronics in projectors
copycat manufacturers offer no guarantee or refunds
the warranty on your Epson EMP-822H projector will become void.

Be sure to purchase an authentic Epson EMP-822H to protect your health and the safety of your projector.

Read more about the 7 Ways to Spot a Counterfeit Lamp.

Buy this lamp on Amazon sold by these authorized dealers:

Install the Epson ELPLP42

Before installation:

Turn off power switch on the back of the Epson EMP-822H projector.
After you turn off the projector’s power and the confirmation buzzer beeps twice, disconnect the power cable
Allow the Epson EMP-822H projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

1. The lamp cover is found on top of the Epson EMP-822H projector. Loosen the lamp cover screw — you can’t remove it only loosen it.

2. Slide the Epson EMP-822H projector lamp cover off.

3. Loosen the two screws holding the Epson ELPLP42 lamp in place.

4. Grab the Epson ELPLP42 lamp by the two indents on the lamp. Gently remove the lamp. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

6. Tighten the screws on the new Epson ELPLP42 lamp.

Epson-EMP-822H-replace-cover-Epson-ELPLP42-lamp

7. Replace the lamp cover and tighten the screw on the EpsonEMP-822H projector lamp cover.

8. Reset the lamp timer.

Reset the lamp timer

Reset the Epson EMP-822H projector Lamp Replacement Counter only when the Epson ELPLP42 lamp has been replaced.

Press the MENU button on the remote control. The Lamp Reset Menu will appear.
Scroll down to the RESET. Press ENTER.
Click on RESET ALL.
A prompt appears asking if you want to replace the lamp.
Select YES and press ENTER.Press MENU to exit.

Prolong the life of the Epson ELPLP42 lamp:

Extend the life of the newly installed Epson ELPLP42 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson EMP-822H projector projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life

Tagged with: authentic lamps, authentic projector lamps, EMP-822H projector, Epson ELPLP42 lamp, Epson projector lamps