About Us - Page 93 of 171 - DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP

A new Epson PowerLite W6 projector lamp in 3 easy steps

Shelagh McNallyPosted on December 19, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Follow this quick guide to install a new lamp in your Epson PowerLite W6 projector.

Scroll down for instructions!

Step 1: When is it time to replace the light?

When it’s time to replace the Epson ELPLP41 in the Epson PowerLite W6, you’ll see the following warning signs:

Dark image
Image that has deteriorated
On warning message appears on screen
Lamp light flashes orange
Lamp light turns red and stays on
Check Lamp Usage

You can expect up to the 3000 hours of use with the Epson ELPLP41 before it needs to be replaced, if you have installed an authentic lamp.

Step 2: Why buy an authentic lamp?

shorter lamp life than original lamps
created with toxic materials and carcinogenic parts including Krypton-85
prone to explosions
can damage the sensitive electronics in your projectors
no guarantee or refunds offered with generic lamps.

Be sure the purchase an authentic Epson ELPLP41 projector lamp for your Epson PowerLite W6 projector. Save yourself unnecessary headaches and buy authentic from a recognized dealer. You’ll be getting a far superior product with a replacement guarantee and tech support.

Read more about the 7 Ways to Spot a Counterfeit Lamp.

Step 3: How to replace the the Epson ELPLP41

Before installation:

Turn power button off wait for light to stop flashing.
Turn off power on Epson PowerLite W6 projector.
Unplug the power cord.
Allow the Epson PowerLite W6 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

1. The lamp cover is found on top of the Epson PowerLite W6 projector. Loosen the lamp cover screw — you can’t remove it only loosen it.

2. Slide the Epson PowerLite W6 lamp cover off.

3. Loosen the two screws holding the Epson ELPLP41 lamp in place.

4. Grab the Epson ELPLP41 lamp by the two indents on the lamp. Gently remove the lamp.

Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP41 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps! If you bought from an authentic manufacturer they will recycle the lamp for you at no extra cost (another reason to buy authentic lamps).

5. Gently insert the Epson ELPLP41 lamp making sure it’s facing the right way.

6. Tighten the screws on the new Epson ELPLP41 lamp.

7. Replace the lamp cover and tighten the screw on the Epson PowerLite W6 lamp cover.

8. You are now ready to reset the lamp timer.

Reset the lamp timer on the Epson PowerLite W6

Reset the Epson PowerLite W6 Lamp Replacement Counter only when the Epson ELPLP41 lamp has been replaced.

Press the MENU button on the remote control. The Lamp Reset Menu will appear.
Scroll down to the RESET LAMP HOURS. Press ENTER.
A prompt appears asking if you want to replace the lamp.
Select YES and press ENTER.
Press MENU to exit.

Prolong the life of the Epson ELPLP41 lamp:

Extend the life of the newly installed Epson ELPLP41 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson PowerLite W6 projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.

Learn more with Top tips for extending DLP projector lamp life

Tagged with: authentic lamps, authentic projector lamps, Epson ELPLP41, Epson PowerLite W6, Epson projector lamps, genuine lamps, genuine projector lamps, Lamp replacement, Projector LAMP, replacement lamps, replacement projector lamps, troubleshooting

Your guide to replacing the Epson PowerLite S6 projector lamp

Shelagh McNallyPosted on December 19, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

When it’s time to replace the Epson ELPLP41 in the Epson PowerLite S6, you’ll see the following warning signs:

Dark image
Image that has deteriorated
On warning message appears on screen
Lamp light flashes orange
Lamp light turns red and stays on
Check Lamp Usage

You can expect up to the 3000 hours of use with the Epson ELPLP41 before it needs to be replaced, if you have installed an authentic lamp.

The importance of authentic lamps

It’s critical to install a genuine Epson ELPLP41 rather than a compatible generic lamps. Although lower in price initially, generic, knock-off lamps end up costing much more in the long run. Counterfeit generic lamp have a shorter lamp life, damage the components in your projector, have poor picture quality and are prone to explosion. You also run the risk of being exposed to the carcinogenic substances such Krypton-85used in the making of these lamps.

Be sure the purchase an authentic Epson ELPLP41 projector lamp for your Epson PowerLite S6 projector. Save yourself unnecessary headaches and buy authentic from a recognized dealer. You’ll be getting a far superior product with a replacement guarantee and tech support.

Read more about the 7 Ways to Spot a Counterfeit Lamp.

Installing the Epson ELPLP41

Before installation:

Turn power button off wait for light to stop flashing.
Turn off power on Epson PowerLite S6 projector.
Unplug the power cord.
Allow the Epson PowerLite S6 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

The lamp cover is found on top of the Epson PowerLite S6 projector. Loosen the lamp cover screw — you can’t remove it only loosen it.

Slide the Epson PowerLite S6 lamp cover off.

Loosen the two screws holding the Epson ELPLP41 lamp in place.

Grab the Epson ELPLP41 lamp by the two indents on the lamp. Gently remove the lamp.

Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP41 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps! If you bought from an authentic manufacturer they will recycle the lamp for you at no extra cost (another reason to buy authentic lamps).

Gently insert the Epson ELPLP41 lamp making sure it’s facing the right way.

Tighten the screws on the new Epson ELPLP41 lamp.

Replace the lamp cover and tighten the screw on the Epson PowerLite S6 lamp cover.
You are now ready to reset the lamp timer.

Reset the lamp timer on the Epson PowerLite S6

Reset the Epson PowerLite S6 Lamp Replacement Counter only when the Epson ELPLP41 lamp has been replaced.

Press the MENU button on the remote control. The Lamp Reset Menu will appear.
Scroll down to the RESET LAMP HOURS. Press ENTER.
A prompt appears asking if you want to replace the lamp.
Select YES and press ENTER.
Press MENU to exit.

Prolong the life of the Epson ELPLP41 lamp:

Extend the life of the newly installed Epson ELPLP41 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson PowerLite S6 projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life

Tagged with: authentic lamps, authentic projector lamps, Epson ELPLP41, Epson PowerLite S6 projector, Epson projector lamps, genuine lamps, genuine projector lamps, lamp, Lamp replacement, Projector LAMP, replacement lamps, replacement projector lamps

How to replace the Epson PowerLite 78 projector lamp

Shelagh McNallyPosted on December 18, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Follow this quick guide to install a new lamp in your Epson PowerLite 78 projector.

Scroll down for instructions!

When is it time to replace the light?

Watch for the signs that the Epson ELPLP41 needs to be replaced in the Epson PowerLite 78:

Dark image
Image that has deteriorated
On warning message appears on screen
Lamp light flashes orange
Lamp light turns red and stays on
Check Lamp Usage

You can expect up to the 3000 hours of use with the Epson ELPLP41 before it needs to be replaced, if you have installed an authentic lamp.

The importance buying authentic lamps

shorter lamp life than original lamps
created with toxic materials and carcinogenic parts including Krypton-85
prone to explosions
can damage the sensitive electronics in your projectors
no guarantee or refunds offered with generic lamps.

Be sure the purchase an authentic Epson ELPLP41 projector lamp for your Epson PowerLite 78 projector. Save yourself unnecessary headaches and buy authentic from a recognized dealer. You’ll be getting a far superior product with a replacement guarantee and tech support.

Read more about the 7 Ways to Spot a Counterfeit Lamp.

Installing the Epson ELPLP41

Before installation:

Turn power button off wait for light to stop flashing.
Turn off power on Epson PowerLite 78 projector.
Unplug the power cord.
Allow the Epson PowerLite 78 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

The lamp cover is found on top of the Epson PowerLite 78 projector. Loosen the lamp cover screw — you can’t remove it only loosen it.

Slide the Epson PowerLite 78 lamp cover off.

Loosen the two screws holding the Epson ELPLP41 lamp in place.

Grab the Epson ELPLP41 lamp by the two indents on the lamp. Gently remove the lamp.

Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

Gently insert the Epson ELPLP41 lamp making sure it’s facing the right way.

Tighten the screws on the new Epson ELPLP41 lamp.

Replace the lamp cover and tighten the screw on the Epson PowerLite 78 lamp cover.
You are now ready to reset the lamp timer.

Reset the lamp timer on the Epson PowerLite 78

Reset the Epson PowerLite 78 Lamp Replacement Counter only when the Epson ELPLP41 lamp has been replaced.

Press the MENU button on the remote control. The Lamp Reset Menu will appear.
Scroll down to the RESET LAMP HOURS. Press ENTER.
A prompt appears asking if you want to replace the lamp.
Select YES and press ENTER.
Press MENU to exit.

Prolong the life of the Epson ELPLP41 lamp:

Extend the life of the newly installed Epson ELPLP41 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson PowerLite 78 projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life

Tagged with: authentic lamps, authentic projector lamps, Epson ELPLP41, Epson PowerLite 78 projector, Epson projector lamps, genuine lamps, genuine projector lamps, lamp, Lamp replacement, Projector LAMP, replacement lamps, replacement projector lamps, troubleshooting

3 Steps to a new Epson Powerlite S5 projector lamp

Shelagh McNallyPosted on December 18, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Install a new lamp in your Epson Powerlite S5 projector is simple and fast.

Follow this 3-step guide to a new Epson ELPLP41 projector lamp.

Step 1: Know when to replace

Watch for the signs that the Epson ELPLP41 needs to be replaced in the Epson Powerlite S5 projector:

Dark image
Image that has deteriorated
On warning message appears on screen
Lamp light flashes orange

You can expect up to the 3000 hours of use with the Epson ELPLP41 before it needs to be replaced, if you have installed an authentic lamp.

Step 2: Buy authentic

You’ll want to protect your investment and buy the best possible lamp for your Epson Powerlite S5 projector. Why jeopardize the projector to save a few dollars. Copycats lamps advertised as “generic compatible” lamps may appear to be a bargain but they actually will end up costing more in the long run. Why? Because generic lamps actually have shorter lamp life than original lamps and are prone to explosions. Since copy cat manufacturers lack the genuine materials, they resort to using toxic materials and carcinogenic parts including Krypton-85.

Be sure to purchase an authentic Epson ELPLP41 projector lamp for your Epson Powerlite S5 projector and avoid incompatible parts that can damage the sensitive components in your projector. Save yourself unnecessary headaches You’ll be getting a far superior product with a replacement guarantee and tech support.

Read more about the 7 Ways to Spot a Counterfeit Lamp.

Step 3: Install the Epson ELPLP41

Before installation:

Turn power button off wait for light to stop flashing.
Turn off power switch on Epson Powerlite S5 projector.
Unplug the power cord.
Allow the Epson Powerlite S5 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

The lamp cover is found on top of the Epson Powerlite S5 projector. Loosen the lamp cover screw — you can’t remove it only loosen it.

Slide the Epson Powerlite 77C lamp cover off.

Loosen the two screws holding the Epson ELPLP41 lamp in place. You be able to remove them completely from the lamp — only loosen them enough to remove the lamp.

Grab the Epson ELPLP41 lamp by the two indents on the lamp. Gently remove the lamp by lifting straight up.

Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

Gently insert the Epson ELPLP41 lamp following the rail guide. Make sure it’s facing the correct way. If it’s not facing the right way, the lamp will not go in properly. Push the lamp down firmly where you see the PUSH label. Tighten the screws on new Epson ELPLP41 lamp when it’s fitted properly into the projector

Replace the lamp cover and tighten the screw on the Epson Powerlite S5 projector lamp cover.
You are now ready to reset the lamp timer.

Reset the lamp timer on the Epson Powerlite S5 projector

Reset the Epson Powerlite S5 Lamp Replacement Counter only when the Epson ELPLP41 lamp has been replaced.

Press the MENU button on the remote control. The Lamp Reset Menu will appear.
Scroll down to the RESET LAMP HOURS. Press ENTER.
A prompt appears asking if you want to replace the lamp.
Select YES and press ENTER.
Press MENU to exit.

Prolong the life of the Epson ELPLP41 lamp:

Extend the life of the newly installed Epson ELPLP41 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson Powerlite S5 projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life

Tagged with: authentic lamps, authentic projector lamps, Epson ELPLP41, Epson Powerlite S5 projector, Epson projector lamps, genuine lamps, genuine projector lamps, Lamp replacement, Projector LAMP, replacement lamps, replacement projector lamps, troubleshooting

The easy way to replace the Epson Powerlite 77C projector lamp

Shelagh McNallyPosted on December 18, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — 2 Comments ↓

Follow this quick 3-step guide to install a new lamp in your Epson Powerlite 77C projector.

Note: These instructions can also be used for the Epson Powerlite 77 projector.

Step 1: When to replace

Watch for the signs that the Epson ELPLP41 needs to be replaced in the Epson Powerlite 77C projector:

Dark image
Image that has deteriorated
On warning message appears on screen
Lamp light flashes orange

You can expect up to the 3000 hours of use with the Epson ELPLP41 before it needs to be replaced, if you have installed an authentic lamp.

Step 2: Buy authentic

6 reasons to buy authentic

generics have shorter lamp life than original lamps
knock off lamps have been created with toxic materials and carcinogenic parts including Krypton-85
generic lamps are prone to explosions
copycat lamps can damage the sensitive electronics in your projectors
no guarantee or refunds offered with generic lamps
your warranty on the Epson Powerlite 77C will be void.

Be sure the purchase an authentic Epson ELPLP41 projector lamp for your Epson Powerlite 77C projector. Save yourself unnecessary headaches and buy authentic from a recognized dealer. You’ll be getting a far superior product with a replacement guarantee and tech support.

Read more about the 7 Ways to Spot a Counterfeit Lamp.

Step 3: Install the Epson ELPLP41

Before installation:

Turn power button off wait for light to stop flashing.
Turn off power switch on Epson Powerlite 77C projector.
Unplug the power cord.
Allow the Epson Powerlite 77C projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

The lamp cover is found on top of the Epson Powerlite 77C projector. Loosen the lamp cover screw — you can’t remove it only loosen it.

Slide the Epson Powerlite 77C lamp cover off.

Loosen the two screws holding the Epson ELPLP41 lamp in place. You not be able to remove them completely from the lamp — only loosen them enough to remove the lamp.

Grab the Epson ELPLP41 lamp by the two indents on the lamp. Gently remove the lamp by lifting straight up.

Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

Replace the lamp cover and tighten the screw on the Epson Powerlite 77C projector lamp cover.
You are now ready to reset the lamp timer.

Reset the lamp timer on the Epson Powerlite 77C projector

Reset the Epson Powerlite 77C Lamp Replacement Counter only when the Epson ELPLP41 lamp has been replaced.

Press the MENU button on the remote control. The Lamp Reset Menu will appear.
Scroll down to the RESET LAMP HOURS. Press ENTER.
A prompt appears asking if you want to replace the lamp.
Select YES and press ENTER.
Press MENU to exit.

Prolong the life of the Epson ELPLP41 lamp:

Extend the life of the newly installed Epson ELPLP41 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson Powerlite 77C projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life

Tagged with: authentic lamps, authentic projector lamps, Epson ELPLP41, Epson Powerlite 77C, Epson projector lamps, genuine lamps, genuine projector lamps, replacement lamps, replacement projector lamps, troubleshooting

3 steps to replacing the Epson EB-S62/EB-X62 projector lamp

Shelagh McNallyPosted on December 18, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Replacing the projector lamp for the Epson EB-S62/EB-X62 is quick and easy.

Follow this 3-step guide to replacing the Epson ELPLP41 projector lamp.

Step 1: Know when to replace

Watch for the signs that the Epson ELPLP41 needs to be replaced in the Epson EEB-S62/EB-X62 projector:

Image that has deteriorated
Dark image
On warning message appears on screen
Lamp light flashes orange
Lamp light turns red and stays on
Check Lamp Usage

To check the number of hours:

You can expect up to 3000 hours from your lamp if the Brightness Controls have been set to High, 4,000 hours if it has been set to Low.

Press the MENU button
Scroll down to highlight the INFO Menu. The number of hours let will be shown on screen.

Step 2: Buy authentic lamps

It’s critical to install a genuine Epson ELPLP41 rather than a compatible generic lamps. Although lower in price initially, generic, knock-off lamps end up costing much more in the long run and come with many problems that just add up to one giant headache. Be sure the purchase an authentic Epson ELPLP41 projector lamp for your EB-S62/EB-X62 projector. You’ll be getting a far superior product with a replacement guarantee and tech support.

6 reasons for avoiding generic lamps

Read more about the 7 Ways to Spot a Counterfeit Lamp.

Step 3: Install the Epson ELPLP41

Before installation:

Turn power button off wait for light to stop flashing.
Turn off power swtich on the back of the Epson EB-S62/EB-X62 projector.
Unplug the power cord.
Allow the Epson EB-S62/EB-X62 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

The lamp cover is found on top of the Epson EB-S62/EB-X62 projector. Loosen the lamp cover screw — you can’t remove it only loosen it.

Slide the Epson EB-S62/EB-X62 lamp cover off.

Loosen the two screws holding the Epson ELPLP41 lamp in place.

Grab the Epson ELPLP41 lamp by the two indents on the lamp. Gently remove the lamp.

Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

Gently insert the Epson ELPLP41 lamp making sure it’s facing the right way.

Tighten the screws on the new Epson ELPLP41 lamp.

Replace the lamp cover and tighten the screw on the lamp cover.
You are now ready to reset the lamp timer.

Reset the lamp timer on the Epson EB-S62/EB-X62

Reset the EB-S62/EB-X62 Lamp Replacement Counter only when the Epson ELPLP41 lamp has been replaced.

Press the MENU button on the remote control. The Lamp Reset Menu will appear.
Scroll down to the RESET LAMP HOURS. Press ENTER.
A prompt appears asking if you want to replace the lamp.
Select YES and press ENTER.
Press MENU to exit.

Prolong the life of the Epson ELPLP41 lamp:

Extend the life of the newly installed Epson ELPLP41 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the EB-S62/EB-X62 projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life.

Tagged with: authentic lamps, authentic projector lamps, Epson EB-S62 projector, Epson EB-X62 projector, Epson ELPLP41, Epson projector lamps, genuine lamps, genuine projector lamps, how to replace Epson projector lamps, Projector LAMP, replacement lamps, replacement projector lamps, troubleshooting

3 Steps to a new Epson EMP-S6 Plus projector lamp

Shelagh McNallyPosted on December 18, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Follow our 3-step guide to replace the lamp in your Epson EMP-S6+ projector? It’s simple to do.

Step 1: Knowing when to replace

Watch for the signs that the Epson ELPLP41 needs to be replaced in the Epson EMP-S6+ projector:

Dark image
Image that has deteriorated
On warning message appears on screen
Lamp light flashes orange
Lamp light turns red and stays on
Check Lamp Usage

Check the number of hours:

You can expect up to 3000 hours from your lamp if the Brightness Controls have been set to High. If Brightness Controls has been set to Low, you can expect, 4,000 hours.

Press the MENU button
Scroll down to highlight the INFO Menu. The number of hours let will be shown on screen.

Step 2: Finding the correct lamp

Why buy authentic? You’ll want to protect your investment and buy the best possible lamp for your Epson EMP-S6+ projector. Why jeopardize the projector to save a few dollars. Copycats lamps advertised as “generic compatible” lamps may appear to be a bargain but they actually will end up costing more in the long run. Why? Because generic lamps actually have shorter lamp life than original lamps and are prone to explosions. Since copy cat manufacturers lack the genuine materials, they resort to using toxic materials and carcinogenic parts including Krypton-85.

Be sure to purchase an authentic Epson ELPLP41 projector lamp for your Epson EMP-S6+ projector and avoid incompatible parts that can damage the sensitive components in your projector. Save yourself unnecessary headaches You’ll be getting a far superior product with a replacement guarantee and tech support.

Step 3: How to install the Epson ELPLP41

Before installation:

Turn power button off wait for light to stop flashing.
Turn off power swtich on the back of the Epson EMP-S6+ projector.
Unplug the power cord.
Allow the Epson EMP-S6+ projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

The lamp cover is found on top of the Epson EMP-S6+ projector. Loosen the lamp cover screw — you can’t remove it only loosen it.

Slide the Epson EMP-S6+ lamp cover off.

Loosen the two screws holding the Epson ELPLP41 lamp in place.

Grab the Epson ELPLP41 lamp by the two indents on the lamp. Gently remove the lamp.

Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

Gently insert the Epson ELPLP41 lamp making sure it’s facing the right way.

Tighten the screws on the new Epson ELPLP41 lamp.

Replace the lamp cover and tighten the screw on the Epson EMP-S6+ lamp cover.
You are now ready to reset the lamp timer.

Reset the lamp timer on the Epson EMP-S6+

Reset the Epson EMP-S6+ Lamp Replacement Counter only when the Epson ELPLP41 lamp has been replaced.

Press the MENU button on the remote control. The Lamp Reset Menu will appear.
Scroll down to the RESET LAMP HOURS. Press ENTER.
A prompt appears asking if you want to replace the lamp.
Select YES and press ENTER.
Press MENU to exit.

Prolong the life of the Epson ELPLP41 lamp:

Extend the life of the newly installed Epson ELPLP41 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson EMP-S6+ projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life

Tagged with: authentic lamps, authentic projector lamps, Epson ELPLP41, Epson EMP-S6 Plus projector, Epson EMP-S6+, Epson projector lamps, genuine lamps, genuine projector lamps, how to replace Epson projector lamps, installation, lamp, Lamp replacement, Projector LAMP, replacement projector lamps

Your guide to a new Epson EMP-S6 projector lamp

Shelagh McNallyPosted on December 18, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Wondering when it’s time to replace the lamp in your Epson EMP-S6 projector? Keep reading.

Know when to replace

Watch for the signs that the Epson ELPLP41 needs to be replaced in the Epson EMP-S6 projector:

Dark image
Image that has deteriorated
On warning message appears on screen
Lamp light flashes orange
Lamp light turns red and stays on
Check Lamp Usage

To check the number of hours:

You can expect up to 3000 hours from your lamp if the Brightness Controls have been set to High, 4,000 hours if it has been set to Low.

Press the MENU button
Scroll down to highlight the INFO Menu. The number of hours let will be shown on screen.

Why buy authentic?

You’ll want to protect your investment and buy the best possible lamp for your Epson EMP-S6 projector. Why jeopardize the projector to save a few dollars. Copycats lamps advertised as “generic compatible” lamps may appear to be a bargain but they actually will end up costing more in the long run. Why? Because generic lamps actually have shorter lamp life than original lamps and are prone to explosions. Since copy cat manufacturers lack the genuine materials, they resort to using toxic materials and carcinogenic parts including Krypton-85.

Be sure to purchase an authentic Epson ELPLP41 projector lamp for your Epson EMP-S6 projector and avoid incompatible parts that can damage the sensitive components in your projector. Save yourself unnecessary headaches You’ll be getting a far superior product with a replacement guarantee and tech support.

How to install the Epson ELPLP41

Before installation:

Turn power button off wait for light to stop flashing.
Turn off power swtich on the back of the Epson EMP-S6 projector.
Unplug the power cord.
Allow the Epson EMP-S6 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

The lamp cover is found on top of the Epson EMP-S6 projector. Loosen the lamp cover screw — you can’t remove it only loosen it.

Slide the Epson EMP-S6 lamp cover off.

Loosen the two screws holding the Epson ELPLP41 lamp in place.

Grab the Epson ELPLP41 lamp by the two indents on the lamp. Gently remove the lamp.

Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

Gently insert the Epson ELPLP41 lamp making sure it’s facing the right way.

Tighten the screws on the new Epson ELPLP41 lamp.

Replace the lamp cover and tighten the screw on the Epson EMP-S6 lamp cover.
You are now ready to reset the lamp timer.

Reset the lamp timer on the Epson EMP-S6

Reset the Epson EMP-S6 Lamp Replacement Counter only when the Epson ELPLP41 lamp has been replaced.

Press the MENU button on the remote control. The Lamp Reset Menu will appear.
Scroll down to the RESET LAMP HOURS. Press ENTER.
A prompt appears asking if you want to replace the lamp.
Select YES and press ENTER.
Press MENU to exit.

Prolong the life of the Epson ELPLP41 lamp:

Extend the life of the newly installed Epson ELPLP41 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson EMP-S6 projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life

Tagged with: authentic lamps, authentic projector lamps, Epson ELPLP41, Epson EMP-S6 projector, Epson projector lamps, genuine lamps, genuine projector lamps, how to replace Epson projector lamps, Projector LAMP, replacement lamps, replacement projector lamps, troubleshooting

Installing a new Epson EMP-400W projector lamp

Shelagh McNallyPosted on December 17, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

How to replace the Epson EMP-400W projector lamp

Follow this guide to replace the Epson EMP-400W projector lamp.

Lamp hour notifications

Watch for the signs that the Epson EMP-400W projector lamp needs replacing:

Dark image
Image that has deteriorated
On warning message appears on screen
Lamp light flashes orange

Authentic vs generic lamps

In order to keep your Epson EMP-400W working at its optimum levels and to prevent damage, you’ll want to buy an authentic projector lamp. The Internet is flooded with companies offering “generic” compatible lamps. Although they seem like a bargain, these should be avoided. They have some very serious flaws:

generic have a much shorter lamp life than OEM lamps
copycat lamps are often created with toxic materials and carcinogenic parts including Krypton-85
compatible lamps are prone to explosions
generic lamps are not calibrated properly and can the sensitive electronics in projectors
copycat manufacturers offer no guarantee or refunds
the warranty on your Epson EMP-400W projector will become void.

Learn how to spot the copycat fake lamps with 7 Ways to Spot a Counterfeit Lamp.

Buy this lamp on Amazon sold by these authorized dealers:

Installing the Epson EMP-400W projector lamp

Before installation:

Turn off power switch on the back of the Epson EMP-400W projector.
After you turn off the projector’s power and the confirmation buzzer beeps twice, disconnect the power cable
Allow the Epson EMP-400W projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

1. The lamp cover is found on top of the Epson EMP-400W projector. Loosen the lamp cover screw — you can’t remove it only loosen it.

2. Slide the Epson EMP-400W projector lamp cover off.

3. Loosen the two screws holding the Epson ELPLP42 lamp in place.

4. Grab the Epson ELPLP42 lamp by the two indents on the lamp. Gently remove the lamp. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP42 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

5. Gently insert the Epson ELPLP42 lamp making sure it’s facing the right way. NOTE: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

6. Tighten the screws on the new Epson ELPLP42 lamp.

7. Replace the lamp cover and tighten the screw on the Epson EMP-400W projector lamp cover.

8. Reset the lamp timer.

Reset the lamp timer

Reset the Epson EMP-400W projector Lamp Replacement Counter only when the Epson ELPLP42 lamp has been replaced.

Press the MENU button on the remote control. The Lamp Reset Menu will appear.
Scroll down to the RESET. Press ENTER.
Click on RESET ALL.
A prompt appears asking if you want to replace the lamp.
Select YES and press ENTER. Press MENU to exit.

Prolong the life of the Epson EMP-400W projector lamp:

Extend the life of the newly installed Epson ELPLP42 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson EMP-400W projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life

Tagged with: authentic lamps, Epson ELPLP42, Epson ELPLP42 lamp, Epson EMP-400W

How to replace the Epson EX21 projector lamp

Shelagh McNallyPosted on December 17, 2012 Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Follow this quick guide to install a new lamp in your Epson EX21 projector.

You can expect up to the 3000 hours of use with the Epson ELPLP41 before it needs to be replaced, if you have installed an authentic lamp. Replacing the Epson ELPLP41 is easy and quick. Scroll down for instructions!

Step 1: When to replace

Watch for the signs that the Epson ELPLP41 needs to be replaced in the Epson EX21 projector:

Dark image
Image that has deteriorated
On warning message appears on screen
Lamp light flashes orange
Lamp light turns red and stays on
Check Lamp Usage

To check the number of hours:

Press the MENU button
Scroll down to highlight the INFO Menu. The number of hours let will be shown on screen.

Step 2: Buy authentic

6 reasons to buy authentic

generics have shorter lamp life than original lamps
knock off lamps have been created with toxic materials and carcinogenic parts including Krypton-85
generic lamps are prone to explosions
copycat lamps can damage the sensitive electronics in your projectors
no guarantee or refunds offered with generic lamps.

Be sure the purchase an authentic Epson ELPLP41 projector lamp for your Epson EX21 projector. Save yourself unnecessary headaches and buy authentic from a recognized dealer. You’ll be getting a far superior product with a replacement guarantee and tech support.

Read more about the 7 Ways to Spot a Counterfeit Lamp.

Step 3: Install the Epson ELPLP41

Before installation:

Turn power button off wait for light to stop flashing.
Turn off power swtich on the back of the Epson EX21projector.
Unplug the power cord.
Allow the Epson EX21 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

The lamp cover is found on top of the Epson EX21projector. Loosen the lamp cover screw — you can’t remove it only loosen it.

Slide the Epson EX21 lamp cover off.

Loosen the two screws holding the Epson ELPLP41 lamp in place.

Grab the Epson ELPLP41 lamp by the two indents on the lamp. Gently remove the lamp.

Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

Gently insert the Epson ELPLP41 lamp making sure it’s facing the right way.

Tighten the screws on the new Epson ELPLP41 lamp.

Replace the lamp cover and tighten the screw on the Epson EX21 lamp cover.
You are now ready to reset the lamp timer.

Reset the lamp timer on the Epson EX21

Reset the Epson EX21 Lamp Replacement Counter only when the Epson ELPLP41 lamp has been replaced.

Press the MENU button on the remote control. The Lamp Reset Menu will appear.
Scroll down to the RESET LAMP HOURS. Press ENTER.
A prompt appears asking if you want to replace the lamp.
Select YES and press ENTER.
Press MENU to exit.

Prolong the life of the Epson ELPLP41 lamp:

Extend the life of the newly installed Epson ELPLP41 with the following tips:

Keep your air filters clean to avoid overheating the projector.
Turn off the Epson EX21 projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
Learn more with Top tips for extending DLP projector lamp life

Tagged with: authentic lamps, authentic projector lamps, Epson ELPLP41, Epson EX21 projector, Epson projector lamps, genuine lamps, genuine projector lamps, how to replace Epson projector lamps, lamp, Lamp replacement, Projector LAMP, replacement lamps, replacement projector lamps, troubleshooting