We're now Screen and Projector! For updated content, visit ScreenAndProjector.com and follow @screenandproj on social media!
Home › About Us › Page 11

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

ProjectionDesign Action! M1 MKII_projectorLearn how to replace the ProjectionDesign Action M1 MKII projector lamp

Be sure to buy your ProjectionDesign Action M1 MKII projector lamp from an authorized dealer to keep your projector working properly.

Your ProjectionDesign Action M1 MKII projector uses the ProjectionDesign 400-0003-00 Projector Lamp.

Find this replacement lamp on Amazon from the following authorized dealers:

6 reasons to avoid counterfeit lamps:

End of life warning signs

When it’s time to replace the ProjectionDesign Action M1 MKII projector lamp projector lamp the projector lamp status indicators will turn red. Other warning signs may include a darker screen or colors that appear washed out or an deteriorating screen image.

How to replace

Before installation follow these important safety steps:

  • Turn off the ProjectionDesign Action M1 MKII projector lamp projector:
  • Unplug the AC cord.
  • These projectors operate under high temperatures and there is a risk of burning if the projector has not cooled enough. Allow the ProjectionDesign Action M1 MKII projector lamp
  • to cool for one hour. It should be cool to the touch.
ProjectionDesign_Action!_M1-MKII_ProjectionDesign_400-0003-00 -warningWhen the ProjectionDesign Action M1 MKII projector lamp is reaching end of life, the INDICATOR light on the on the keypad will turn red. Change the lamp when lifetime expires.
ProjectionDesign_Action!_M1-MKII_ProjectionDesign_400-0003-00-remove cover
NOTE: Be careful not to touch the protective glass when replacing the lamp house, this may cause the protective glass to overheat and break while in use.
A. Release the front cover screw.
ProjectionDesign_Action!_M1-MKII_ProjectionDesign_40 0-0003-00-remove-cover-b
B. Remove the front cover. Put it to one side
ProjectionDesign_Action!_M1-MKII_ProjectionDesign_400-0003-00_lamp_screws
C. Un-screw the three mounting screws.
0-0003-00_remove_lamp-3
D.  Release the handle and pull the lamp out.
WARNING: Be extremely careful when removing the lamp module. In the unlikely event that the bulb ruptures, small glass fragments may come loose. The lamp module is designed to contain these fragments, but use caution when removing the lamp module.
NOTE: The ProjectionDesign 400-0003-00 projector lamp contains mercury and should not be thrown into regular garbage. Recycle this lamp!
ProjectionDesign_Action!_M1-MKII_ProjectionDesign_400-0003-00_insert_new_lamps
Replace with a new lamp in reverse order.
E. Insert a new lamp. Observe the guide pins.
ProjectionDesign_Action!_M1-MKII_ProjectionDesign_400-0003-00_tighten_screws
F. Fix the three mounting screws firmly. Do not use excess
force.
ProjectionDesign_Action!_M1-MKII_ProjectionDesign_400-0003-00_replace_lamp_final
G. Re-position the handle.
Replace the front cover.
Fix the front cover screw carefully, but do not use excess force.

 

 

Each time you replace the ProjectionDesign 400-0003-00 projector lamp you will need to reset the PProjectionDesign Action M1 MKII projector lamp lamp timer so the projector can accurately track the lamp hours. To reset the:
  • Open the MENU option. Press ENTER.
  • Scroll down to the UTILTIES submenu.
  • Press reset the lamp time.

Extending the projector lamp life

  • Use the Eco Mode for more lamp hours.
  • Keep your air filters clean to avoid overheating the projector.
  • Make sure there is enough airflow around the ProjectionDesign Action M1 MKII projector lamp.
  • Learn more with Top tips for extending DLP projector lamp life

Learn more tips for extending lamp life.

Tagged with: , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Follow this guide to replace the Vivitek D510 projector lampvivitek_D510_projector

Go with authentic

When it’s time for a new Vivitek D510 projector lamp, the best investment you can make is to buy an authentic projector lamp. An authentic OEM lamp is gauranteed to keep your Vivitek D510 working at its best. Knock-off counterfeit lamps have a shorter lamp life and have been created with toxic substitutes and are prone to explosions that s often damage the sensitive electronics in your projectors. Invest in authentic.

Find this lamp on Amazon sold by these authorized dealers:

Replacing the projector lamp

When you notice the Power LED flashing 5 times consecutively, your projector lamp is reaching its end of life and needs to be replaced immediately. The Vivitek D510 projector uses the Vivitek 5811116320 projector lamp . Before changing the Vivitek D510 projector lamp:

  • Reduce the risk of electrical shock by disconnecting the power cord on the Vivitek D510 projector.
  • Reduce the risk of severe burns by allowing the projector to cool for at least 45 minutes.

Vivitek_D510_projector_lamp_5811116320-S

  • Loosen the captive screw holding the lamp cover in place.
  • Slide the lamp cover off and place it to one side.
    • Remove the three captive screws holding the lamp cover place.
    • Left the handle up.
    • Disconnect the lamp connectors. Vivitek_D510_projector_lamp_5811116320-S_connectors

 

 

 

 

NOTE: The Vivitek 5811116320 projector lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

Vivitek_D510_projector_lamp_5811116320-S_install_replacementTo finish the installation:

  • Take the new Vivitek 5811116320 projector lamp out of its packaging. Lift up the wire handle and gently guide it into the Vivitek D510 projector.
  • Take care not to touch the actual bulb as the oil from your fingers can leave a smudge that will burn into a black spot when the projector heats up.
  • While installing, align the lamp  module with the connector and ensure it is level. The Vivitek 581111
    must sit securely in the place before tightening the screw.
  • Reset the total lamp hour timer.

Resetting the Vivitek D510 Lamp Hour Timer

It’s important to only reset the lamp timer when the projector lamp has been replaced.

Vivitek_D510_projector_lamp_5811116320-S_reset_timerResetting the projector lamp timer without changing the lamp can make it work beyond its recommended hours and cause harm to your Vivitek D510 projector.

  • Press the Menu button to open the OSD menu.
  • Press left/right arrow keys to move to the Advanced menu.
  • Press up/down arrows to move to the Lamp menu.
  • Press Enter.
  • Using the or up/down arrow keys to move down to the Reset Lamp Timer menu.
  • Press Enter.
  • A message will appear saying the Lamp Hour has been reset to zero.
  • Press the Menu button to return to the main menu.

Extending the life of the projector lamp:

  • Keep your air filters clean to avoid overheating the projector.
  • Use the Lamp Power option on the Vivitek D510 projector and set to Eco Mode to reduce the amount of power used but extend projector lamp life.
  • Learn more with Top tips for extending DLP projector lamp life.

 

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides, uncategorized — No Comments ↓

Canon LV-WX300 projectorHow to install a new Canon LV-WX300 projector lamp

When it’s time to replace the Canon LV-WX300 projector lamp you’ll see a lamp replacement icon appear on screen and the LAMP REPLACE indicator will light orange. Replace the lamp immediately. When the projector is in operation, the duration (in hours) of lamp usage is automatically calculated by the built-in timer.

Buy this lamp on Amazon sold by these authorized dealers:

 

Watch for the warning signs on screen:

Canon_LV-WX300_projector_Canon LV-LP38_replacement_lamp_warnings

First warning: The lamp has been in operation for 4500 hours. Install a new lamp

for optimal performance. If the Canon LV-WX300 projector is operating in Economic mode, you can use the the to 4950 hour.

Second warning: The lamp has been in operation for 4950 hours. Get your authentic replacement projector lamp ready .

Third warning: The lamp has been in operation for 5000 hours. It is strongly recommended that you replace the lamp

Final Warning: The lamp MUST be replaced before the projector will operate

Install the projector lamp

Your Canon LV-WX300 projector uses the Canon LV-LP39 projector lamp model. Before replacing the lamp follow these safety instructions:

  • Unplug the electrical cord on the Canon LV-WX300 so there is no chance the projector could get turned on during the installation.
  • The Canon LV-WX300 operates under high temperatures so give it at least one hour to cool down before opening the projector to change the projector lamp.

Canon_LV-WX300_projector_Canon LV-LP38_replacement_lamp_remove_cover

Canon_LV-WX300_projector_Canon LV-LP38_replacement_lamp_remove

  • Loosen the screw holding the Canon LV-LP39 projector lamp cover in place.

    Lift the lamp cover up. Do not turn the power on with the lamp cover removed.

Canon_LV-WX300_projector_Canon LV-LP38_replacement_lamp_replace

 

Canon_LV-WX300_projector_Canon LV-LP38_replacement_lamp_install

  • Replace the lamp assembly with a new Canon LV-LP39 projector lamp. Be careful not to touch the actual bulb as oil from your fingers can leave black marks on the lamp.
  • Close the lamp cover

 

Resetting the lamp timer counter

After replacing the Canon LV-WX300 projector lamp, you’ll need to reset the lamp. To reset:

Canon_LV-WX300_projector_Canon LV-LP38_replacement_lamp_reset_timer

  • Restart the projector.
  • Open the On-Screen Display (OSD) menu.
  • Go to the SYSTEM SETUP: Advanced>Lamp Settings menu.
  • Press OK/IMAGE. The Lamp Settings page is displayed. Press to highlight/ Reset lamp timer and press OK/IMAGE.
  • A warning message is displayed asking if you want to reset the lamp timer. Highlight Reset and press OK/IMAGE . The lamp time will be reset to ‘0’.

Learn how to prolong lamp life with Top tips for extending projector lamp life.

 

Tagged with: , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Geha_Compact_650PLUS_projectors_Geha_60-246697_lampUse this guide to replace the Geha Compact 650+ projector lamp

Go with an authentic Geha Compact 650Plus Projector lamp

Go with authentic

Stay away from copycat counterfeits lamps in order to keep your Geha Compact 650+ working properly. Counterfeit lamps will damage the sensitive optics in the projector and has a shorter life particularly since they are likely to explode. Knock offs are also created with toxic materials that pose a health threat. Authentic lamps are safer and come with a money-back guarantee as well as keeping your warranty intact.  Avoid counterfeit lamps and go with an authentic Geha Compact 565+ projector lamp!

Find this lamp on Amazon from these authorized dealers:

End of life

GEHA-650+ projector_Geha_60-246697_lamp_warningWhen it’s time to replace your Geha Compact 650+ projector lamp a warning sign will appear on screen. Replace the lamp immediately when you see this warning. Other warning signs includes a dark image or one with colors that are faded.

Replacing the projector lamp

The Geha Compact 650+ uses the Geha 60-246697 projector lamp. Before installation follow these important safety steps:

  • Turn off the Geha Compact 650+ projector and unplug the AC cord.
  • These projectors operate under high temperatures and there is a risk of burning if the projector has not cooled enough. Allow the Geha Compact 650+ to cool for one hour. It should be cool to the touch.Geha_Compact_650PLUS_projectors_replace_Geha_60-246697_lamp

1. Remove the two screws from the cover.

2. Lift the cover off the projector and place it to one side.

3. Remove the two screws holding the Geha Compact 650+ projector lamp in place. screw from the cover.

3. Lift the wire handle on the Geha 60-246697 lamp and gently pull the lamp up to remove it.

Don’t throw the old Geha 60-246697 into regular garbage as it contains mercury — send it to a local recycling program.

4. Take the new Geha 60-246697 projector lamp using the wire handle. Avoid touching the bare bulb; the oil on your finger can leave a black mark on the lamp affecting the projected image. Tighten the screws on the new Geha 60-246697 projector lamp.

Put the lid back onto the projector. Tighten the screw holding the lid in place. Plug the AC cables back into the projector. Turn the project on so you can reset the lamp timer.

Resetting the projector lamp timer

It’s important to always reset the lamp timer after replacing the projector lamp in your Geha Compact 650+ projector. You want the projector to track how many hours the lamp has been used and send out warning messages when the Geha 60-246697 projector lamp reaches end of life.

To reset the Projector Lamp timer:

  • Turn on the projector
  • Press MENU
  • Scroll down to OPTIONS
  • Choose Lamp Settings. Press ENTER.
  • Select Lamp Reset to open an additional dialogue box.
  • Select YES. Press Enter

Extending the projector lamp life

  • Use the Eco Mode for more lamp hours.
  • Keep your air filters clean to avoid overheating the projector.
  • Make sure there is enough airflow around the Geha Compact 650+ projector.
  • Learn more with Top tips for extending DLP projector lamp life

A green alternative

Geha_60-246697_replace_bulb_lamp

The Geha Compact 650+ projector has the option of just replacing the actual bulb and re-using the plastic cage. A great was to reduce, recycle and reuse.  Watch our training video to learn more.

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Hitachi_CP_X201_projectorReplace the Hitachi CP-X201 projector lamp

Watch for these signs when the Hitachi CP-X201 projector lamp is reaching end of life:

  • Both the Hitachi CP-X201 Power and Lamp Indicators are flashing red while the Temp Indicator is turned off.
  • Color tone on the screen may also appear weak or washed out.
  • Picture has poor color quality.

Authentic lamps

Only an OEM authentic replacement projector lamp will keep your Hitachi CP-X201 projector working. Look for the seal of approval before purchasing. Learn to spot copycat lamps posing as authentic lamps. Keep track of projector lamp life so you’ll know when to replace the projector lamp. Avoid generics because they have a shorter life than originals as well as being prone to explosions and created with toxic substitute parts. They can damage the sensitive optics in your Hitachi CP-X205 projector and as well as hurt your eyesight.

Find this lamp sold on Amazon by these authorized distributors:

Install the Hitachi projector lamp

Safety steps before installing the Hitachi DT00841:

  • Turn off the Hitachi CP-X201 projector.
  • Unplug the power cord.
  • Allow the projector to cool for at least 45 minutes. It should be cool to the touch. This projector works using high heat and there is danger you can be burned.
  • NOTE: If the projector is mounted on the ceiling, don’t stand underneath the projector while opening the cover.

Hitachi_CP-X201_projector_Hitachi DT00841_projector_lamp

  • Prepare the new Hitachi CP-X201 projector lamp. If the projector is mounted on a ceiling, or if the lamp has broken, contact your dealer for assistance.
  • Loosen the screw (marked by arrow) of the lamp cover and then slide the lamp cover to the side to remove it.
  • Loosen the 2 screws (marked by arrow) of the Hitachi DT00841 projector lamp, and slowly pick up the lamp by the handles. Be careful not the bang the lamp. The Hitachi DT00841 projector lamp contains mercury and must be recycled properly. Do not throw it in regular garbage.
  • Insert the new lamp, taking care not to touch the actual bulb. Oil in your fingers will cause a dark spot on the lamp when it heats up.
  • Tighten the two screws of the Hitachi DT00841 projector lamp that were loosened to remove the old projector lamp.
  • Slide the lamp cover back in place and firmly fasten the screw of the lamp cover.
  • Turn on the projector and set the lamp timer:

To reset the projector lamp timer:

Hitachi_CP-X305_projector_Hitachi-DT00841_projector_lamp_reset_timerNote: Reset the projector lamp time only when you have replaced the lamp so the Hitachi CP-X201 projector can properly track the lamp life. Otherwise you run the risk of using the lamp beyond its life.

  • Press the MENU button
  • Scroll down to the GO TO ADVANCED MENU option. Press ENTER
  • Scroll down to the OPTION menu in the left column and press ENTER.
  • Scroll down to LAMP TIME. Press ENTER To make a dialogue field appear
  • Scroll up to the RESET option on the dialogue box.
  • The lamp setting will be set to zero.

Replacing the air filters

Get more hours from your Hitachi DT00841 by keeping your air filters clean to avoid overheating the projector.

  • Pull the filter frame’s knob up while holding the filter cover. The filter frame will come off and the air filter will appear.
  • Take out the old air filter and insert the new air filter.
  • Put the filter frame back.
  • Put the filter unit back into the projector
  • Turn the projector on and reset the filter time using the FILTER TIME item in the EASY MENU.
  • Learn more with Top tips for extending DLP projector lamp life.

Green your projector

Hitachi_DT00841_replacement_projector_lamp_training_video

 

Recycle your lamp housing by only replacing the Hitachi CP-X201 lamp. Our training video shows you how to do it. It’s easy!

 

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Install a new Epson EX3210 projector Epson EX7210 projector lamp

The Epson EX7210 projector lamp is easy to replace by following this tutorial.

Look for the seal of approval before buying your Epson EX7210 projector lamp. Keep reading for the 6 reasons to avoid counterfeit lamps.

Find this lamp on Amazon sold by these authorized dealers:

6 reasons to avoid generic lamps:

Watching for end of life

It’s time to replace the Epson EX7210 projector lamp projector lamp when the following signs are seen:

  • The projected image gets darker or starts to deteriorate.
  • A message appears saying to replace the lamp when the projector is turned off
  • The projector lamp warning light flashes orange.

Installing the Projector Lamp Replacement

Before installation:

  • Turn power button off wait for light to stop flashing.
  • Turn off power switch on Epson EX7210 projector lamp projector.
  • Unplug the power cord.
  • Allow the Epson EX7210 projector lamp projector to cool for one hour. It should be cool to the touch before changing the projector lamp.
  • Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Caution: Don’t touch the actual bulb with your fingers since the oil from your skin can cause a black spot on the bulb.

Installing the Epson ELPLP67 projector lamp

Epson_EX7210_projector_Epson_ELPLP67_replacement_lampLoosen the lamp cover screw and slide the Epson EX7210 projector lamp cover off.

Epson_EX7210_projector_Epson_ELPLP67_remove_projector_lampLoosen the two screws holding the Epson ELPLP67 projector lamp in place.

NOTE: The Epson ELPLP67 projector lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

Epson_EX7210_projector_Epson_ELPLP67_replacement_projectors_lamp_step2Grab the Epson ELPLP67 projector lamp by the wire handle and gently pull the sprojector lamp out. Pulling too quickly can cause the bulb to shatter. Learn what to do should this happen. Gently insert the Epson ELPLP67 projector lamp making sure it’s facing the right way.

Epson_EX7210_projector_Epson_ELPLP67_insert_new_replacement_lampTighten the screws on the new Epson ELPLP67 projector lamp. Be sure not to tighten too much or the lamp may not work.

Replace the lamp cover and tighten the screw on the Epson EX3210 projector lamp projector lamp cover. You a ready to reset the projector lamp timer.

 

Reset the projector lamp timer

Reset the Epson EX7210 projector lamp projector Lamp Replacement Counter only when the Epson ELPLP67 projector lamp has been replaced.

Epson_EX7210_projector_Epson_ELPLP67_rest_lamp_timer

  • Press the MENU button on the remote control. The Lamp Reset Menu will appear.
  • Scroll down to the RESET LAMP HOURS. Press ENTER.
  • A prompt appears asking if you want to RESET LAMP HOURS?
  • Select YES and press ENTER.
  • Press MENU to exit.

Prolong the life of the projector lamp:

Extend the life of the newly installed Epson ELPLP67 projector lamp with the following tips:

  • Keep your air filters clean to avoid overheating the projector.
  • Turn off the Epson EX7210 projector lamp projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
  • Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
  • Learn more with Top tips for extending DLP projector lamp life

 

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

This guide shows you how to replace the Epson EX3210 projector Epson EX3210 projector lamp

An authentic Epson EX3210 projector lamp will make all the difference in performance.

Why invest in authentic projector lamps

Look for the seal of approval before buying your Epson EX3210 projector lamp. Keep reading for the 6 reasons to avoid counterfeit lamps.

Find this lamp on Amazon sold by these authorized dealers:

6 reasons to avoid generic lamps:

Watching for end of life

It’s time to replace the Epson EX3210 projector lamp projector lamp when the following signs are seen:

  • The projected image gets darker or starts to deteriorate.
  • A message appears saying to replace the lamp when the projector is turned off
  • The projector lamp warning light flashes orange.

Installing the Projector Lamp Replacement

The Epson EX3210 projector lamp uses the Epson ELPLP67 projector lamp replacement.

Before installation:

  • Turn power button off wait for light to stop flashing.
  • Turn off power switch on Epson EX3210 projector lamp projector.
  • Unplug the power cord.
  • Allow the Epson EX3210 projector lamp projector to cool for one hour. It should be cool to the touch before changing the projector lamp.
  • Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Caution: Don’t touch the actual bulb with your fingers since the oil from your skin can cause a black spot on the bulb.

Installing the Epson ELPLP67 projector lamp

Epson_EX3210_projector_Epson_ELPLP67_replacement_lampLoosen the lamp cover screw and slide the Epson EX3210 projector lamp cover off.

Epson_EX3210_projector_Epson_ELPLP67_remove_projector_lampLoosen the two screws holding the Epson ELPLP67 projector lamp in place.

NOTE: The Epson ELPLP67 projector lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

Epson_EX3210_projector_Epson_ELPLP67_replacement_projectors_lamp_step2Grab the Epson ELPLP67 projector lamp by the wire handle and gently pull the sprojector lamp out. Pulling too quickly can cause the bulb to shatter. Learn what to do should this happen. Gently insert the Epson ELPLP67 projector lamp making sure it’s facing the right way.

Epson_EX3210_projector_Epson_ELPLP67_insert_new_replacement_lampTighten the screws on the new Epson ELPLP67 projector lamp. Be sure not to tighten too much or the lamp may not work.

Replace the lamp cover and tighten the screw on the Epson EX3210 projector lamp projector lamp cover. You a ready to reset the projector lamp timer.

 

Reset the projector lamp timer

Reset the Epson EX3210 projector lamp projector Lamp Replacement Counter only when the Epson ELPLP67 projector lamp has been replaced.

Epson_EX3210_projector_Epson_ELPLP67_rest_lamp_timer

  • Press the MENU button on the remote control. The Lamp Reset Menu will appear.
  • Scroll down to the RESET LAMP HOURS. Press ENTER.
  • A prompt appears asking if you want to RESET LAMP HOURS?
  • Select YES and press ENTER.
  • Press MENU to exit.

Prolong the life of the  projector lamp:

Extend the life of the newly installed Epson ELPLP67 projector lamp with the following tips:

  • Keep your air filters clean to avoid overheating the projector.
  • Turn off the Epson EX3210 projector lamp projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
  • Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
  • Learn more with Top tips for extending DLP projector lamp life

 

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

optoma GT750E projectorsInstall a replacement Optoma GT750E projector lamp

When the Optoma GT750E projector lamp approaches end of life, a replacement message will flash on screen. You may also notice the picture quality starting to have poor resolution with washed out colors. Change your projector lamp immediately. The projector will not work if the lamp has burnt out or broken.

Find this lamp from the following OEM manufacturers on Amazon:

Buying the right brand of projector lamp

Your Optoma GT750E projector uses the Optoma BL-FP230H Replacement Lamp. Be prepared and have your authentic replacement projector lamp ready and waiting. If you are buying over the Internet, avoid projector lamps with a low price tag for the following reasons:

Learn 7 ways to spot a counterfeit projector lamp.

Installing the replacement lamp

Before replacing the Optoma GT750E projector follow these important safety tips:

  • Switch off the power to the Optoma GT750E projector by pressing the Power/Standby button.
  • Disconnect the power cord.
  • Allow the projector to cool down for at least 30 minutes. If should be cool to the touch. These projectors run using high temperatures and you can burn yourself badly if you don’t allow the projector to cool down.

Optoma_GT750E_projector_Optoma BL-FP230H_lamp

1. Use a screwdriver to undo the two screws holding the lamp cover in place. The screws on the lamp cover and the lamp cannot be removed.

2. Remove the lid and place to one side. Don’t lose the lid as the projector will not turn back on until the lamp cover has been properly installed.

3. Remove the two screws holding the Optoma BL-FP230H in place.

Note: The used Optoma BL-FP230H lamp contains mercury and should be properly recycled. Don’t throw it into regular garbage. Please recycle this lamp.

4. Lift up the wire handle on the Optoma BL-FP230H lamp and slowly remove it from the projector.

Be careful not to bang the lamp against the projector as this may case the bulb to break. Learn how to clean up a broken lamp.

5. Remove the new Optoma BL-FP230H from its packaging. Taking care not to touch the actual bulb, lift up the handle on the new lamp and insert it gently into the GT750E projector.

6. Tighten the two screws on the lamp.

7. Replace the lamp cover and tighten its two screws. You are now ready to reset the Lamp Replacement Timer.

Reset the Lamp Replacement Timer

The Optoma GT750E projector has an automatic lamp timer that tracks the numbers of hours left in the lamp. If you don’t reset the lamp replacement timer you run the risk of the lamp being used beyond its recommended life and possibly exploding in the projector.

To reset the Lamp Replacement Timer:

  • Turn on the projector.
  • Press MENU.
  • Select SYSTEM.
  • Select Lamp Settings.
  • Select Lamp Reset.
  • Select Yes.
  • Press MENU to exit.

Tips for extending projector lamp life:

  • Keep your air filters clean to avoid overheating the projector.
  • Every 24 hours, turn off the projector and let it stand for 1 hour
  • Make sure there is enough airflow around the Optoma GT750E projector particularly if it’s been permanently mounted.
  • Learn more with Top tips for extending DLP projector lamp life
Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

BenQ_W1000_projectorHow to replace the BenQ W1000 projector lamp

Start off with authentic

Save yourself unnecessary headaches and purchase an authentic BenQ W1000 projector lamp. Why go authentic? Counterfeit “compatible” lamps may appear to be a bargain but in the long run end up costing more due to their shorter lamp life. They are prone to explosions and can put your eyesight at risk. Due to their substitute toxic materials and carcinogenic parts, the few dollars you will save are not worth it. Protect your health and keep your BenQ W1000 working at optimum levels. Go with an authentic projector lamp.

You can buy the replacement lamp on Amazon from these authorized dealers:

 

End of life warning signs

Your BenQ W1000 projector uses the BenQ 5J.J0W05.001 replacement projector lamp. When it’s time to replace the BenQ W1000 projector lamp you’ll see a series warnings appear on screen.

BenQ_W1000_projector_5J.J0W05.001_projector_warnings

 

First warning: Order Replacement Lamp The BenQ W1000 projector lamp has been in operation for 3500 hours. Install a new lamp for optimal performance.

 

Second Warning: Replace Lamp Soon. The BenQ W1000 projector lamp has been in operation for 3950 hours. A new lamp should be fitted to avoid the inconvenience of the projector shutting down when the lamp reaches end of life.

 

Third warning: Replace Lamp Now. The BenQ W1000 has been in operation for 4000 hours. Replace the lamp immediately.  The lamp brightness diminishes with use. If the lamp is not replaced beforehand, it must be replaced after 4000 hours usage.

 

Final warning: Lamp usage time exceeded. The lamp MUST be replaced before the projector will operate normally.

 

Follow these safety instructions before changing the lamp:

  • Reduce the risk of electrical shock by disconnecting the power cord on the BenQ W100 projector.
  • Reduce the risk of severe burns by allowing the projector to cool for at least 45 minutes. The projector should be cool to the touch.

Replacing the projector lamp

  • BenQ_W1000_projector_5J.J0W05.001_coverThe projector lamp cover is found on the side of the BenQ W100 projector.
  • Loosen the screw holding the projector lamp cover in place
  • Lift up the projector lamp cover.

BenQ_W1000_projector_5J.J0W05.001_remove_projector_lamp

 

  • Loosen the screws that secure the lamp.
  • Do not turn the power on with the lamp cover removed.
  • Do not insert your fingers between the lamp and the projector. The sharp edges inside the projector may cause injuries.
  • Lift the handle so that it stands up. Use the handle to slowly pull the lamp out of the projector.
  • NOTE: Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector.

    Do not insert your hands into the projector after the lamp is removed.

    • BenQ_W1000_projector_5J.J0W05.001_install_projector_replacement_lamp

    The BenQ 5J.J0W05.001 projector lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

  • Insert the new BenQ 5J.J0W05.001 lamp compartment and make sure it fits in the projector. Ensure the connectors are aligned. If there is resistance, lift the lamp and start again.

 

  • Tighten the screws that secure the lamp.Loose screw may cause a bad connection, which could result in malfunction.  Do not over tighten the screw.
  • Ensure the handle is fully laid flat and locked in place. Replace the lamp cover on the
  • projector.
  • Press the lamp cover down until the click is heard locking the projector.
  • You are ready to reset the lamp timer

Resetting the lamp timer

Do not reset the BenQ W100 projector lamp timer if the lamp has not been replaced as this could cause damage. Don’t start the if the lamp cover has not been replaced. To reset the projector lamp timer:

BenQ_W1000_projector_5J.J0W05.001_reset_lamp_timer

  • After the startup logo, open the On-Screen Display (OSD) menu. Go to the SYSTEM SETUP: Advanced Lamp Settings menu.
  • Press MODE/ENTER. The Lamp Settings page displays. Press to
  • highlight.
  • Reset lamp timer and press MODE/ENTER.
  • A warning message displays asking if you want to reset the lamp timer. Highlight Reset and press MODE/ENTER.
  • The lamp time will be reset to ‘0’
  • Lamp time will be reset to zero.

Extend the BenQ MS614 projector lamp

 

Save

Save

Save

Save

Tagged with: , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides, Rear Projection TV Lamp Replacement — No Comments ↓

Our guide walks you through replacing the Sony KDS-R60XBR2 TV lamp

When to replace?

When the Sony KDS-R60XBR2 TV lamp  is reaching end of life, you will see a message on screen and the lamp indicator on the TV will start flashing. Other end of life signs may also include darker images and colors that look off.

The Sony KDS-R60XBR2 TV uses the Original Lamp For SONY KS 70R200A:KDS R70XBR2:KDS R60XBR2:KDS 70R2000 Rear projection TV

Find this lamp on Amazon.

To replace the projector lamp

The Sony KDS-R60XBR2 TV uses the Sony XL-5300 Replacement TV Lamp. Perform there safety steps before installing the new projector lamp:

  • Turn off the power on the main unit.
  • The cooling fan will continue to operate for two minutes after the power is turned off.
  • Wait several minutes before unplugging the power cord.
  • Wait an additional 30 minutes to allow the lamp to cool down. The lamp operates under extreme so avoid touching it before changing the lamp.

Sony_KDSR70XBR2_remove_Xl-5300_lamp_cover

Remove the outside Sony XL-5300 projector lamp cover. Click the switch open to remove the lamp cover.

Sony_KDSR70XBR2_remove_Xl-5300_lamp

 

 

Remove the inner lamp door. Turn the screw counterclockwise, and then turn the knob to the left until
the marks on the lid and the case line up. Remove the door.
Sony_KDSR70XBR2_install_new_Xl-5300_lampPull out the Sony XL-5300 lamp. Hold the indents on the top and bottom of the lamp, and pull the Sony XL-5300 lamp straight out. Do not touch the inside of the lamp compartment. Never touch the glass portion of the lamp or the surrounding parts.

NOTE: This projector lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

Sony_KDSR70XBR2_install_replacement_Xl-5300_lampPut the new Sony XL-5300 lamp into its place and make sure it’s securely mounted into the compartment. Failure to do so may cause a fire or the screen to go dark.

Sony_KDSR70XBR2_disconnect_Xl-5300_lampNOTE: The lamp compartment is tilted, as shown in the following illustration. If the Sony XL-5300 lamp is not securely reattached, the self-diagnostic function may be triggered and the POWER LED blinks three times.

 

Sony_KDSR70XBR2_reconnect_replacement_Xl-5300_lampReattach the lamp door. To secure the door, turn the knob to the right while pushing the door in, until the marks on the lid and the and the case line up. Then, turn the screw clockwise to tighten the door.
Sony_KDSR70XBR2_reinstall_door_Xl-5300_lamp
Put the outside lamp cover back in its place.
Replace the cover, inserting it from the left side. Press the clamp on the
right side to secure the cover.
You are ready to reset the Lamp Replacement option in order to track the hours of projector lamp.

Reset the Lamp Replacement option

Until you set the Lamp Replacement option, a message announcing that the is at the end of its life will appear every time you turn on the TV. You will need to reset. After the Sony XL-5300 lamp is replaced, you must select this Setup option or this message will continue to appear when you first turn on the TV.
Sony_KDSR70XBR2_reset_timer
Select this option after you replace the lamp.
Depending on environmental conditions, such as frequency of use, some
lamps may burn out before the lamp replacement message appears on the TV.
  • Press the MENU button on the remote control. Scroll down to the SETUP option.
  • Scroll down to the LAMP REPLACEMENT. Press ENTER.
  • A prompt appears asking if you want to reset the lamp hours.
  • After the lamp is replaced, you must select this option or this message will
    continue to appear when you first turn on the TV.

Authentic lamps are critical!

Don’t settle for anything but the best for your Sony KDS-R60XBR2 TV. When buying look for the seal of approval.

6 reasons to avoid generic LCD projector lamps:

 

Green your Sony XL-5300 TV

Sony XL-5300 TV_replacement_lamp

If you interested in going green with your KDS-R60XBR2, you can replace only the projector bulb and re-used the plastic casing. This can save your money plus help reduce waste. Watch our training video to learn more.

Find this lamp on Amazon:

Tagged with: , ,
Join the discussion on Facebook! All your questions, answered! The Screen & Projector Group