We're now Screen and Projector! For updated content, visit ScreenAndProjector.com and follow @screenandproj on social media!
Home › About Us › Page 10

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

BenQ_MX713ST_projectorReplace the BenQ MW714ST projector lamp

Go with authentic

Protect your projector by investing in an authentic lamp. An authentic OEM projector lamps is the only lamp that will keep your BenQ MW714ST projector working properly. Here are four reasons to avoid using counterfeit projector lamps:

Shop for this lamp on Amazon sold by these authorized distributors:

Warning signs for end of projector lamp

BenQ-_MW714ST_projector_BenQ 5J.J3K05_projector_lamp_warningWhen the BenQ MW714ST projector lamp is reaching end of life, three warning messages will appear on screen. The lamp indicator on the projector will start flashing orange. You may notice the image deteriorating or the color looking off. Lamp hour information can be found on the INFORMATION menu.Setting the projector to economic mode will extend the projector lamp life.

Replacing the projector lamp

Before changing the lamp:

  • Reduce the risk of electrical shock by disconnecting the power cord on the BenQ MW714ST projector.
  • Reduce the risk of severe burns by allowing the projector to cool for at least 45 minutes.

BenQ-_MW714ST_projector_BenQ 5J.J3K05_projector_lamp_remove_cover_screw

Loosen the screw holding the BenQ MW714ST projector lamp cover. The BenQ MW714ST projector uses the BenQ 5J.J3K05.001

BenQ_MW714ST_projector_lamp_remove_cover

Lift up the cover. Remove and dispose of the lamp protection film. Do not insert your fingers between the lamp and the projector. The sharp edges inside the projector may cause injuries.

 

BenQ-_MW714ST_projector_BenQ 5J.J3K05_disconnect_projector_lamp

Disconnect the projector lamp connector from the projector Loosen the screw that secures the BenQ 5J.J3K05.001 projector lamp.

BenQ-_MW714ST_projector_BenQ 5J.J3K05_remove_old_projector_lamp

 

Slowly and gently pull the BenQ 5J.J3K05.001 projector lamp out of the projector. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The BenQ 5J.J3K05.001 projector lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps.

BenQ-_MW714ST_projector_BenQ 5J.J3K05_install_new_projector_lamp

Insert the new BenQ 5J.J3K05.001 projector lamp first into the connector on the projector and reconnect the lamp connector.

Make sure the handle is fully locked. Tighten the projector lamp screw. If the screw is too loose or too tight, the projector may not turn on.

Re-install the BenQ MW714ST lamp cover and tighten the screw. Reset the total lamp operation t

Reset the projector lamp counter

BenQ-_MW714ST_projector_BenQ 5J.J3K05_reset_projector_lamp_timerWhen the BenQ 5J.J3J05.001 projector lamp in the BenQ MW714ST projector has been changed the projector lamp timer must be reset:

  • Turn on the BenQ MW714ST projector.
  • After the startup logo, open the On-Screen Display (OSD) menu.
  • Go to the SYSTEM SETUP.
  • Scroll over to Advanced > Lamp Settings menu.
  • Press MODE/ENTER to display Lamp Settings page is displayed.
  • Highlight Reset lamp timer. A warning message is displayed asking if you want to reset the lamp timer.
  • Highlight Reset and press MODE/ENTER. The lamp time will be reset to “0”.

Extend the projector lamp life:

  • Keep your air filters clean to avoid overheating the projector.
  • Use the Lamp Power option on the BenQ MW714ST and set to Economic Mode to reduce the amount of power used by 20%.
  • Learn more with Top tips for extending DLP projector lamp life.

 

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in Articles, Counterfeit Awareness, Counterfeit Lamp Awareness, FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

omparison_authentic_counterfeitAuthentic projector lamps save you time and money

With guaranteed OEM authentic projector lamps,  you’ll never experience the frustration of down time from a projector ruined by a defective lamp. Three important things to watch for: Arc distance, wattage, reflector size.

Protect your health

Health and safety is always important. One of the associated risks from DLP projectors is exposure to high-intensity projector lights that can damage eyesight. Genuine PHILIPS lamps are manufactured with UV coated reflectors to reduce harmful rays and protect your eyesight. Generic lamps don’t offer this safety feature.

Why invest in authentic?

PHILIPS is the premier manufacturer projector and TV lamps. They have spent years researching and developing the sophisticated technology of projector. Here are three things to look for with authentic projector lamps.

 Arc distance

authentic_projector_lamps-arc_distance

Projector bulbs have an arc gap filled with ultra-high pressurized mercury vapor that creates the high intensity light needed to project the image onto the screen. There is an optimal arc distance needed in every projector lamps that is 1.0 mm. Getting this exact measurement takes the right equipment and even the slightest deviations from this exact measurement can result in loss of contrast, brilliance and light eventually damaging the optical components on the projector.

Wattage

authentic_projector_lamps-wattageWattage plays a critical role in lamp power as it supplies the amount of light displayed. Generics usually have higher wattage and when they come in contact with the low wattage ballast/driver (which controls the electrical ignition of the lamp), the projector’s electrodes can be damaged. Since the generic lamp produces too much light, there is often a flickering image, uncontrolled light exposure and overheating of the lamp and projector.

Reflector Size

authentic_projector_lamps-reflectorGenerics often have a different sized reflector than original OEM lamps, which means they often don’t fit into the projector properly. Bad position of the lamp means the light does not go through the optical elements at the right angle causing damage to the optics and a short circuit of electrical components. This leakage of light can also affect your eyesight by exposing you to high intensity light.

Learn more about projector lamps and what to look for

 

Tagged with: , , , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Eiki POA-LMP132 projector lampHow to replace the Eiki LC-XBL25 projector lamp

When the Eiki LC-XBL20 projector lamp nears the end of life, the Lamp replacement icon appears on the screen. At the same time the LAMP REPLACE indicator starts flashing yellow. Eiki_lc-xbl20_LampReplace

Buy authentic

If you are buying over the Internet, avoid projector lamps with a low price tag for the following reasons:

Learn 7 ways to spot a counterfeit projector lamp. Protect your health and the life of your projector. Invest in authentic.

Find this lamp on Amazon sold by these authorized dealers:

 

How to replace the LC-XBL25 projector lamp

The Eiki LC-XBL25 projector uses Eiki POA-LMP132 projector lamp.

Before installation:

  • Turn off the projector and unplug the AC cord.
  • Allow the Eiki LC-XBL25 projector lamp projector to be cool to the touch. This can take between 45 to 60 minutes. Don’t open the projector when hot since these machines operate under high temperatures and you can burn yourself.

1. Remove the lamp cover fiki_LC-XBL20_projector_lamp_replacement_Sanyo_POA-LMP132or the Eiki LC-XBL25 projector. Loosen the screw to remove the cover.

2. Loosen all three screws holding the lamp cage in place. Grab the handles on the lamp cage and gently lift the lamp out of its socket. Place to one side.

NOTE: These lamps contain mercury and should be properly recycled. Don’t put it into the regular garbage.

3. Take the new Eiki POA-LMP132 projector lamp by the handle—avoid touching the lamp surface as oil from your fingers can cause black spots to appear when the projector is turned on. Gently maneuver the lamp into place. Don’t force the lamp as this may damage it.

4. Once the lamp is in, tighten all three screws on the Eiki POA-LMP132 Lamp Assembly. Make sure the screws have been tightened properly or the Eiki LC-XBL25 projector will not turn on.

5. Replace the Lamp Cover and tighten the screw.

Resetting the Eiki LC-XBL25 Lamp Timer

Resetting the lamp timer mode allows your projector accurately track the number of hours left in your Eiki POA-LMP132 projector lamp.

Eiki_LC-XBL20_projector_lamp_replacement_Sanyo_POA-LMP132_LampCounter

  • Turn the Eiki LC-XBL25 on.
  • Press the Menu option to display the On-Screen Menu.
  • Press Point left/right button(s) to move a red frame poster to Setting Menu icon.
  • Press the black arrow point button to move the red framed pointer to the Setting Menu Icon.
  • Press Point Down button to move the red frame pointer to Lamp counter reset.
  • Press the Select button.

 

Eiki_LC-XBL20_projector_lamp_replacement_Sanyo_POA-LMP132_LampReset-3

  • Another confirmation dialog box appears, select YES.
  • The Lamp box will disappear and the Lamp Replace Dialog box appears.
  • Select YES to reset Lamp Replace Counter.
  • There are two modes for Lamp life control. Mode 1 lets the lamp be turned on even after exceeding the recommended total hours of use. Mode 2 lets the lamp be turned on even after exceeding the recommended total hours BUT the projector turns off automatically after 3 minutes.

 

NOTE: When you reset the Lamp Replace Counter the Lamp Replace indicator stops lighting.

Extend the life of the projector lamp

Get more hours from your Eiki POA-LMP132 projector lamp by following these maintenance tips:

  • Keep your air filters clean to avoid overheating the projector.
  • Turn off the Eiki LC-XBL25 projector and let it stand unused for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
  • Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
  • Learn more with Top tips for extending DLP projector lamp life.

 

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides, uncategorized — No Comments ↓

Mitsubishi LVP SA51UX projectorHow to install a replacement Mitsubishi LVP SA51UX projector lamp

The best investment you can make is to invest in an authentic Mitsubishi LVP SA51UX projector lamp. Knock-off counterfeit lamps have a shorter lamp life and have been created with toxic substitutes and are prone to explosions that s often damage the sensitive electronics in your projectors. Invest in authentic. This Mitsubishi LVP SA51UX projector uses the Mitsubishi VLT-PX1LP model.

Buy this lamp on Amazon from the following retailers:

Warning

The Mitsubishi LVP SA51UX projector lamp has a lamp life of approximately 2,000 hours. End of lamp life indicators include a decreases in luminescence and/or color brightness. At 1500 hours, the indicator will flash alternately between green and red. When the lamp has been used for close to 1,900 hours, a message “LAMP!!.” appears on the screen for one minute. When the lamp has reached about 2,000 hours, the projector will automati-
cally shut off for safety and the power indicator light will be red. The lamp must be replaced immediately.

Replacing the projector lamp

Before replacing the projector lamp, please follow these safety precautions.

  • Reduce the risk of electrical shock by disconnecting the power cord on the Mitsubishi LVP SA51UX projector.
  • Reduce the risk of severe burns by allowing the projector to cool for at least 45 minutes. It should be cool to the touch.

Mitsubishi_LVP SA51UX_projector_lamp_VLT-PX1LP_remove_cover

Reverse the projector gently and place it on a soft surface.
Loosen the screws of the lamp lid to remove the lid.
Mitsubishi_LVP SA51UX_projector_lamp_VLT-PX1LP_remove_lampRemove the lamp cover in the direction of the arrow as indicated. Loosen the two screws on the Mitsubishi VLT-PX1LP lamps (a). Pull up the handle.
Hold onto the Mitsubishi VLT-PX1L projector lamp by the handle as you pull straight
upward. Note: The used Mitsubishi VLT-PX1L lamp contains mercury and should be properly recycled. Don’t throw it into regular garbage. Please recycle this lamp.
Mitsubishi_LVP SA51UX_projector_lamp_VLT-PX1LP_insert
Insert the new Mitsubishi VLT-PX1 projector lamp securely into the Mitsubishi LVP SA51UX projector in the right direction.
• Make sure the two section of the lamp are properly positioned into the proper holes before inserting the lamp (b).
Mitsubishi_LVP SA51UX_projector_lamp_VLT-PX1LP_replacement
Put the handle back to the holding point making sure the  handle is locked.
Tighten up the screws (a) using a phillips screwdriver (+).
Put the lamp lid back onto the Mitsubishi LVP SA51UX projector Tighten up the screws of the lamp lid using

Resetting the Lamp Hour Timer

It’s important to only reset the lamp timer when the Mitsubishi LVP SA51UX lamp has been replaced. Resetting the projector lamp timer without changing the lamp can make it work beyond its recommended hours and cause harm to your projector.

To reset the lamp operation time

  • Plug in the power cord
  • Reset the lamp operation time by holding down the ARROW key and the POWER button on the control panel at the same time.
  • Make sure that the STATUS indicator blinks twice and the lamp operation time is reset successfully.
  • IMPORTANT: Unless these three buttons are pressed at the same time, the lamp operation time isn’t reset.

Extending the life of the projector lamp:

 

Tagged with: , , ,

by avatarShelagh McNallyPosted on Posted in Articles, FixYourDLP — No Comments ↓

dollar-authenticWhat is the real cost of counterfeit lamps?

Replacing the DLP lamp is one of the expenses associated with owning a projector or a RPTV. The low prices of counterfeits lamps are tempting. Who doesn’t love a bargain?

Remember that “you get what you pay for” when you are online shopping around for the lowest price. Projector lamps are not your ordinary light bulb. The cost of creating this advanced technology is reflected in the price. If you come across a projector lamp that seems like an incredible bargain it’s probably counterfeit.

True costs

We need a cost analysis of the actual cost of counterfeit lamps and they turn out to be more expensive that original OEM lamps.

hidden costs

Copy-cat manufacturers can be clever at disguising their knock-off products including using original PHILIPS logos and parts numbers. So even if the lamp looks authentic if the price is too good to be true, then chances are it’s a counterfeit.

Authentic technology

projector lamps

On the surface counterfeit brands may appear to be the same but their technology is actually quite different from the OEM lamps manufactured by Philips Lighting.

DLP Projectors use high pressure to generate light and this pressure needs to be controlled inside the lamp.  Authentic projector lamps have been calibrated to the exact wattage in order to control the pressure.

Too high a pressure may result in the lamp exploding and damaging the inside of your projector. You may need to replace the color wheel or the AV board.

TV Lamps cost

If the damage is too bad, the projector may need to be replaced.

What is the real cost?

Tagged with: , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides, uncategorized — 4 Comments ↓

optoma HD25 projectorHow to replace the Optoma HD25 projector lamp

When the Optoma DH1011 projector lamp approaches end of life, a replacement message will flash on screen. You may also notice the picture quality starting to have poor resolution with washed out colors. Change your projector lamp immediately. The projector will not work if the lamp has burnt out or broken.

Optoma_HD25_projector_lamp_BL-FU250A_warning

Buying the right lamp

Your Optoma HD25 projector uses the Optoma BL-FU240A.

Learn 7 ways to spot a counterfeit projector lamp.

Installing the Optoma HD25 lamp

Before replacing the Optoma BL-FU24 follow these important safety tips:

  • Switch off the power to the Optoma HD25 projector by pressing the Power/Standby button.
  • Disconnect the power cord.
  • Allow the projector to cool down for at least 30 minutes. If should be cool to the touch. These projectors run using high temperatures and you can burn yourself badly if you don’t allow the projector to cool down.

Optoma_HD25_projector_lamp_BL-FU250A-replace

1. Use a screwdriver to undo the two screws holding the lamp cover in place. The screws on the lamp cover and the lamp cannot be removed.

2. Remove the lid and place to one side. Don’t lose the lid as the Optoma HD25 projector will not turn back on until the lamp cover has been properly installed.

3. Remove the two screws holding the Optoma BL-FU24 in place.

Note: The used Optoma BL-FU24 lamp contains mercury and should be properly recycled. Don’t throw it into regular garbage. Please recycle this lamp.

4. Lift up the wire handle on the Optoma BL-FU24 lamp and slowly remove it from the projector.

Be careful not to bang the lamp against the projector as this may case the bulb to break. Learn how to clean up a broken lamp.

5. Remove the new Optoma BL-FU24 from its packaging. Taking care not to touch the actual bulb, lift up the handle on the new lamp and insert it gently into the Optoma HD25 projector.

6. Tighten the two screws on the lamp.

7. Replace the lamp cover and tighten its two screws. You are now ready to reset the Lamp Replacement Timer.

Reset the Lamp Replacement Timer

The Optoma HD25 projector has an automatic lamp timer that tracks the numbers of hours left in the lamp. If you don’t reset the lamp replacement timer you run the risk of the lamp being used beyond its recommended life and possibly exploding in the projector.

To reset the Lamp Replacement Timer:

  • Turn on the projector.
  • Press MENU.
  • Select OPTIONS.
  • Select Lamp Settings.
  • Select Lamp Reset.
  • Select Yes.
  • Press MENU to exit.

Tips for extending projector lamp life:

  • Keep your air filters clean to avoid overheating the projector.
  • Every 24 hours, turn off the projector and let it stand for 1 hour
  • Make sure there is enough airflow around the Optoma HD25 projector particularly if it’s been permanently mounted.
  • Learn more with Top tips for extending DLP projector lamp life
Tagged with: , , ,

by avatarShelagh McNallyPosted on Posted in Articles, FixYourDLP — No Comments ↓

FIFA_World_Cup_2014

As we head into the final rounds of the FIFA World Cup, there is still time to create your home theater.

A 1080p high definition TV projector will give you the clearest picture and sharpest colors to enjoy this international event. Options for watching TV shows and movies in your living room have never been more varied. Once you have chosen a room for your home theater, the next step will be to gather all the necessary components.

Where will you be watching?

Today’s digital projectors handle a wide variety of media from video, TV, photos or documents. The type of digital projector you buy will depend on how you’re going to use it. Home theater projectors are generally used in completely dark room, so don’t need to bright as home projectors. A general TV projector used in a bright room with more ambient light may need a brighter projector. It may be worth spending a big more money for a projector that can handle different types of lighting with more focus options.

Consider your ceilings

Any home theatre also needs a screen and that is dependent on your ceiling. Ceiling height controls screen height and width and ultimately how far back your projector will need to be. Does this mean you need a short-throw projector or one that can be further back from the screen. Any screen must be at least three feet off the floor. Subtract three feet from your ceiling height and this will be your maximum screen height and will give you an idea of how big a screen you need. Look for a projector with a lens shift option. One of the most important considerations when setting up your home theater is looking at the aspect ratio as well as the projector’s gain.

Pick out the screen

The type of screen you need depends on your projector, the amount of light in the room, the size of the room and the viewing angle distance from the screen. The first step to buying your screen is learning about the various kinds of projector screens that both your budget and projector. There are four basic types of projectors screens:

  • Electric
  • Permanent, fixed frame
  • Manual pull down
  • Portable

Read more about screens and their and material.

Speakers

Good sound is an important as the screen. With your home theater, the speakers are not going to be next to the projector. You’ll need cables to hook up the projector to the speakers you have chosen. You can fore go the cables and use a wireless connection for your speakers. A Sound Bar system produces a surround sound listening environment using one speaker box. If there isn’t room for cables or you don’t want unsightly clutter, you can also invest on wireless speaker. An AV input switcher is also an important piece of equipment by allowing you to swap between your different video sources such as your computer, DVD player or BlueRay device.

 

Tagged with: , , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

epson_eb-z11005nl_projectorFollow our guide for installing a new Epson Z11005NL projector lamp

When it’s time to replace the Epson Z11005NL projector lamp, you’ll notice the following warning signs:

  • The power light is flashing blue and the Lamp 1 or Lamp 2 light is flashing orange
  • The message “Lamp Replace” appears on the screen
  • The images gets darker or starts to deteriorates.

Find this lamp on Amazon from the following authorized dealers:
Epson V13H010L83 projection lamp

 

Keep your projector working

A genuine projector lamp is the only lamp that will keep your Epson PZ11005NL projector lamp working at its optimum levels. An OEM authentic lamps have been manufactured to meet the specifications of the Epson Z11005NL projector.

Counterfeit projector lamps can damage the sensitive and expensive mechanisms in your Epson Z11005NL projector and actually have a much shorter lamp life. They are also more prone to explosions due to the inferior materials used during their production.

Look for the seal of approval and buy from an authentic manufacturer. Learn how to protect yourself from counterfeit manufacturers.

Installing Epson projector lamp

Preparation:

1. Turn off the projector power and wait for the cool-down period which is about two minutes. Disconnect the power cord after the two minutes is over.

2. Wait at least 30 minutes to one hour for the Epson Z11005NL projector lamp projector to cool internally before opening it up. It should be cool to the touch.

NOTE: Do not operate the projector while the projector lamp is removed as this may result in malfunctions, fire hazard and other accidents.

Epson_Z11005NL_projector_lamp_ELPLP81_remove cover

Slide the lamp cover latch to the Open position and slide the lamp cover to the left.
Epson_Z11005NL_projector_lamp_ELPLP81_lamp_cover-2

 

Remove the lamp cover.
Epson_Z11005NL_projector_lamp_ELPLP82_remove_lamp

This projector uses two lamps and they may both need to be replaced at the same time. Pull up the lock lever for the lamp you want to replace and pull the lamp straight out of the projector.

Gently pull the projector lamp out of the Epson Z11005NL projector. Don’t knock the actual bulb as it may break. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP81 projector lamp contains mercury and should not be thrown into regular garbage. Please recycle this lamp.

Epson_Z11005NL_projector_lamp_ELPLP81_installSlowly insert the Epson ELPLP81 projector lamp until it clicks into place. Be sure not to touch the actual bulb as the oil from your skin will case blackouts.

 

FlEpson_Z11005NL_projector_lamp_ELPLP81_lock_newip down the lock lever and press until it clicks into place.Epson_Z11005NL_projector_lamp_ELPLP81_replace_lamp_cover

Close the lamp cover. Slide the lamp cover to the right until it clicks, and slide the lamp cover latch to the Close position.

Resetting the lamp timer

The projector lamp timer will need to be reset after replacing the Epson ELPLP81. This timer helps the Epson PowerLite Z11005NL projector lamp proiector to properly track the lamp life. Only reset the timer when a new Epson ELPLP81  projector lamp has been installed, otherwise the projector will NOT know when it’s time to replace the lamp. You run the risk of damaging your projector.

Epson_Z11005NL_projector_lamp_ELPLP81_replace_lamp_cover

  • Turn on the projector.
  • The lamp replace message will appear automatically.
  • It will ask if you want to reset the lamp.
  • Select YES. Press ENTER.
  • Click on RESET ALL.
  • The lamp hours will be reset to zero. The lamp usage timer shows 0H until you’ve used the lamp for at least 10 hours.

How to extend the life of the Epson Z11005NL lamp:

Extend the life of the newly installed Epson ELPLP81 projector lamp with the following tips:

  • Keep your air filters clean to avoid overheating the projector.
  • Turn off the Epson Z11005NL projector lamp projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
  • Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
  • Learn more with Top tips for extending DLP projector lamp life.
Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

optoma_technology_dh1011_1080pHow to replace the  Optoma DH1011 projector lamp

When the Optoma DH1011 projector lamp approaches end of life, a replacement message will flash on screen. You may also notice the picture quality starting to have poor resolution with washed out colors. Change your projector lamp immediately. The projector will not work if the lamp has burnt out or broken.

Optoma_DH1011_projector_lamp_BL-FU250A_warning

Buying the right lamp

Your Optoma HD300X projector uses the Optoma BL-FU240A.

 

Buy this lamp on Amazon from the following authorized dealers:


If you are buying over the Internet, avoid projector lamps with a low price tag for the following reasons:

Learn 7 ways to spot a counterfeit projector lamp.

Buy this lamp on Amazon from the following authorized dealers:

Installing the Optoma DH1011 lamp

Before replacing the Optoma BL-FU24 follow these important safety tips:

  • Switch off the power to the Optoma DH1011 projector by pressing the Power/Standby button.
  • Disconnect the power cord.
  • Allow the projector to cool down for at least 30 minutes. If should be cool to the touch. These projectors run using high temperatures and you can burn yourself badly if you don’t allow the projector to cool down.

Optoma_DH1011_projector_lamp_BL-FU250A-replace

1. Use a screwdriver to undo the two screws holding the lamp cover in place. The screws on the lamp cover and the lamp cannot be removed.

2. Remove the lid and place to one side. Don’t lose the lid as the Optoma DH1011 projector will not turn back on until the lamp cover has been properly installed.

3. Remove the two screws holding the Optoma BL-FU24 in place.

Note: The used Optoma BL-FU24 lamp contains mercury and should be properly recycled. Don’t throw it into regular garbage. Please recycle this lamp.

4. Lift up the wire handle on the Optoma BL-FU24 lamp and slowly remove it from the projector.

Be careful not to bang the lamp against the projector as this may case the bulb to break. Learn how to clean up a broken lamp.

5. Remove the new Optoma BL-FU24 from its packaging. Taking care not to touch the actual bulb, lift up the handle on the new lamp and insert it gently into the Optoma DH1011 projector.

6. Tighten the two screws on the lamp.

7. Replace the lamp cover and tighten its two screws. You are now ready to reset the Lamp Replacement Timer.

Reset the Lamp Replacement Timer

The Optoma DH1011 projector has an automatic lamp timer that tracks the numbers of hours left in the lamp. If you don’t reset the lamp replacement timer you run the risk of the lamp being used beyond its recommended life and possibly exploding in the projector.

To reset the Lamp Replacement Timer:

  • Turn on the projector.
  • Press MENU.
  • Select OPTIONS.
  • Select Lamp Settings.
  • Select Lamp Reset.
  • Select Yes.
  • Press MENU to exit.

Tips for extending projector lamp life:

  • Keep your air filters clean to avoid overheating the projector.
  • Every 24 hours, turn off the projector and let it stand for 1 hour
  • Make sure there is enough airflow around the Optoma DH1011 projector particularly if it’s been permanently mounted.
  • Learn more with Top tips for extending DLP projector lamp life
Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Acer _7763P_projectorThis guide shows how to replace the Acer 7763P projector lamp

When to replace

When it’s time to replace the Acer 7763P projector lamp warning messages will be play on screen. Be sure to purchase an authentic lamp.

 

Other signs of end of life include a faded picture or distorted colours on screen. The power lamp will also begin flashing amber. Replace the projector lamp immediately.

Buy this lamp on Amazon sold by these authorized dealers:

The importance of authentic

Counterfeit “compatible” lamps may appear to be a bargain but actually cost more in the long run.  The few dollars you save with counterfeit “compatible” lamps are not worth it in the long run. Save yourself unnecessary headaches — buy an Acer 60.J1610.001 projector lamp from a recognized dealer. You’ll be getting a far superior product with a replacement guarantee and tech support.

Reasons for not buying counterfeit projector lamps:

Replace the Acer 7763P projector lamp

When the Acer 7763P projector lamp is reaching final hours and exceeds the 1500 service hour, the LED light will flash continuous red. Warning message will begin to flash on screen.

Acer_Projector_ 7763P_Acer 60.J1610.001_projector_lamp_first_warning

First warning: “CHANGE THE LAMP, AND RESET THE LAMP TIMER” will be displayed on the screen if the lamp has been operated for 1200 hours

Acer_Projector_ 7763P_Acer 60.J1610.001_projector_lamp_warning-2Second warning:
“CHANGE THE LAMP, THE POWER WILL TURN OFF AFTER 20 HOURS” will be displayed The “20” count down begins.
projector_lamp_Warning-3
Thirs  warning:“CHANGE THE LAMP!” will blink on the screen together with a red LED when 1500 hours has been reached.

How to replace the projector lamp

The Acer 7763P uses the Acer 60.J1610.001 projector lamp. Before installation make sure the projector is cool to the touch before replacing the projector lamp. There is a risk of burning if the projector has not cooled sufficiently.

Acer_Projector_ 7763P_Acer 60.J1610.001_projector_lamp_remove_lamp_cover

Turn the power off on the projector. Unplug it from the power source.

Loosen the screw holding the lamp cover on the projector. Put the lamp cover to one side.

Acer_Projector_ 7763P_Acer 60.J1610.001_projector_lamp_replaceRemove the screw holding the  from the Acer 7763P projector lamp. Lift the handle and pull out the lamp.

NOTE: The Acer 60.J1610.00 projector lamp contains mercury and should not be thrown into regular garbage. Recycle this lamp!

Insert the new Acer 60.J1610.00 projector lamp taking care not to touch the glass bulb. Oil from your fingers can burn marks into the lamp.

Tighten the screw on the lamp and replace the lamp cover. You are ready to reset the lamp timer.

Resetting the projector lamp timer

When you change the Acer 7763P projector lamp you will need to reset the lamp timer so the projector can accurately track the number hours of left.

  • Acer_Projector_ 7763P_Acer 60.J1610.001_projector_lamp_reset
  • Press the Exit button on the projector for 3 seconds or the Exit button on the remote control for 3 seconds and display the total lamp usage time.
  • Press the Menu button on the projector or the remote control while the lamp usage time is being displayed, and the lamp hour display will be active and adjustable.
  • Select the “Reset” item on the screen using the buttons or on control pad or remote.

Extending the projector lamp life

Learn more tips for extending lamp life.

 

Tagged with: , , ,
Join the discussion on Facebook! All your questions, answered! The Screen & Projector Group