We're now Screen and Projector! For updated content, visit ScreenAndProjector.com and follow @screenandproj on social media!
Home › About Us › Page 8

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Dell_1609HD_projector_Dell_311-8943_projector_lampThis guide shows you how to replace the Dell 1609 projector lamp.

Invest in authentic!

Keep your Dell 1609HD projector working by always installing an authentic projector lamp. The Dell 1609HD uses the Dell 311-8943 projector lamp. Scroll down to learn why you should always avoid counterfeit projector lamps.

Find this lamp on Amazon sold by these authorized dealers:

End of projector lamp warnings

When it’s time for a new projector lamp you’ll see an on-screen message saying: “Lamp is approaching the end of its useful life in full power operation. Replacement suggested!” You may also see a blinking amber light on the Dell 1609 warning that the projector lamp is approaching end of life.

If you wait too long you’ll see a “Lamp Defective” on screen message followed by a loud pop inside. Your Dell 1609 projector will then shut off.

 

Dell_1609HD_projector_Dell_311-8943_725-1012_replace_projector_lampReplacing the Dell 1609 projector lamp

Before replacing the Dell 311-8943 projector lamp be sure to turn the projector off and disconnect from the AC plug. Let the projector cool down for at least 30 minutes. It should be cool to the touch. Don’t attempt to change the lamp when the projector is still hot as there is a good chance you can get severely burned.

  • Place the Dell 1609HD on a soft surface and turn in upside down to access the projector lamp cover. Loose the two screws that hold the projector lamp cover in place.
  • Loosen the two screws that secure the projector lamp.
  • Pull the projector lamp up by its metal handle. Pulling too quickly can cause the bulb to shatter. NOTE: Don’t throw the Dell 311-8943 projector lamp into regular garbage! Since it contains mercury, this lamp must be properly recycled.
  • Install the new Dell 311-8943 projector lamp making sure it is properly aligned into the projector.
  • Tighten the two screws that secure the Dell 311-8943 projector lamp.
  • Replace the projector lamp cover and tighten the two screws.
  • You are now ready to reset the lamp timer.

Reset the Dell 1609 projector lamp counter

The Dell 1609 projector tracks the life of the Dell 311-8943 projector lamp and will trigger the warning signals when it’s time to replace. Each time you replace the Dell 311-8943 projector lamp you must reset the lamp timer to zero. Failure to do so can result in you using the projector past the optimum lamp life and causing the projector lamp to explode.

Dell_1609HD_projector_Dell_311-8943_projector_lamp_hours

  • To access the Main Menu press the left or right buttons on your projector’s control panel or remote control.
  • Scroll over the the LAMP Menu. Press ENTER to access.
  • Scroll down to the Lamp Reset icon. Press ENTER.
  • Scroll down to choose YES and press ENTER to reset the projector lamp timer

Tips for extending Dell 1609 projector lamp life:

  • From the LAMP Menu, choose ECO MODE: Select On to use the projector at the lower power level of 165 Watts, which makes the Dell 1609 projector operate quieter and with lower light that gives more projector lamp life. Select off to operate at the 200 Watts power level.
  • Keep your air filters clean to avoid overheating the projector.
  • Every 24 hours, turn off the projector and let it stand for 1 hour
  • Make sure there is enough airflow around the Dell 1609 projector particularly if it’s been permanently mounted.
  • Learn more with Top tips for extending DLP projector lamp life.

Save money and go green

Dell_1409X _projector_Dell_311-8943_725-1012_replace_projector_lamp_bulb

 

Looking for a green alternative for the Dell 1609 projector? Try replacing only the projector lamp bulb and re-using the same plastic cage with the 311-8943 projector lamp. Watch our training video to see learn.

Why avoid counterfeits?

Generic lamps should be avoided because of a variety of problems including:

Protect your health and keep your Dell 1609 projector from being damaged. Invest in a Dell 311-8943 authentic projector lamps! Look for the seal of approval!

 

Tagged with: , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

JVC DLA-RS65 projectorInstall a new JVC DLA-RS65 projector lamp

Look for these indicators when it’s time to replace the JVC DLA-RS40 projector lamp:

  • LAMP indicator starts flashing. Replace the lamp immediately
  • Poor picture quality/strange colors
  • Flickering lights or darker light

Lamp life is approximately 3000 hours but may vary depending on maintenance and usage.

Find this lamp on Amazon from the following authorized dealers:

Buy authentic

Be sure to invest in an authentic lamp for your JVC DLA-RS65 projector lamp. This projector uses the JVC PK-L2210UP projector lamp. Be sure to invest in an authentic lamp.

Why avoid counterfeit projector lamps:

Projector lamp replacement

BEFORE replacing the lamp:

  • Turn off the projector and unplug the AC cord.
  • Allow the JVC DLA-RS65 projector lamp to cool for at least one hour. Don’t open the projector until it is cool to the touch. These projectors operate under high temperatures and you can run the risk of burning yourself.

JVC_DLA-RS65_projector_lamp_PKPK-L2210UP_cover

  • Loosen the screw holding the projector lamp cover into the projector. Place the cover to one side.JVC_DLA-RS65-install new lamp_JVC PK-L2210UP
  • Loosen the two screws keeping the JVC PK-L2210UP projector lamp in place. Grab wire handle and gently pull the lamp out taking care not to hit the lamp.

JVC_DLA-RS65-install new lamp_JVC PK-L2210UP

  • Take the JVC PK-L2210UP projector lamp by the wire handle and gently pull it from the projector. NOTE: This lamp contain mercury and can’t be placed into regular garbage. Recycle this lamp.
  • JVC_DLA-RS65-install new lamp_JVC PK-L2210UPPlace the replacement JVC PK-L2210UP into the JVC DLA-RS65 projector. Avoid touching the glass or the bulb since the oil from your fingers may cause black spots on the bulb when the projector heats up.
  • Tighten the two screws on the new JVC PK-L2210UP lamp.
  • Replace the JVC DLA-HD1 projector lamp cover. You’ll need to reset the Lamp Counter.

Resetting the projector lamp timer

Each time you replace the JVC DLA-RS65 projector lamp you need to reset the lamp timer to zero. Not resetting the lamp timer will result in your projector not turning back on because it thinks the old lamp has not been replaced.

To reset the lamp:

  • Display the Main Menu screen. Scroll over to select the FUNCTION option
  • Scroll down to the LAMP RESET option
  • Press the Enter button
  • A second option screen will open asking toe Reset Lamp Timer
  • Scroll down to select YES
  • The lamp timer will be reset to zero.

Tips for longer projector lamp life:

  • Avoid frequent on and offs to avoid power surges.
  • Don’t let the JVC DLA-RS65 projector overheat as this puts stress on the lamp. Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
  • Let the projector stand unused for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
  • Keep the air filters clean and free of dust so it can do its job and keep the projector lamp for overheating.

Learn more with Top tips for extending DLP projector lamp life.

Save

Save

Tagged with: , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Compaq MP2810 projectorInstall a replacement Compaq MP2800 projector lamp in 3 steps

Start by recognizing the signs that the Compaq MP2810 projector lamp has reached its end of life. Warning signs include a dim picture or color that appears to be washed out. When the message “”Lamp May Fail Soon – Replacement Suggested” “displays on the projection screen replace the lamp immediately.

Go with authentic

The Compaq MP2800 projector uses the Compaq 215464-001 projector lamp. Be sure to invest in authentic.

Be sure to install an authentic Compaq MP2810 projector lamp. There is nothing more frustrating that having your Compaq MP2800 projector shut down as you are trying to use it.

Here are four reasons to avoid using counterfeit projector lamps:

Find this lamp on Amazon sold by these authorized dealers:

Compaq Lamp Replacement Kit for Mp2800 / 2810

Installing the replacement projector lamp

Compaq_MP_2810_projector_lamp_215464-001_power

Step 1: Turn off the power to the projector by pressing the blue Standby button .
Step 2: Allow the Compaq MP2810 to cool down for at least 30 minutes.
Step 3: Disconnect the power cord.

 

Compaq MP2810_projector_lamp_215464-001_power_replaceStep 4: Use a coin to loosen the screw  on the Compaq 215464-001 lamp module.
Step 5: On the front of the Compaq 215464-001 lamp slide up the latch to release it from the projector base.
Step 6: Pull out the Compaq 215464-001 lamp module.

NOTE: The used Compaq 215464-001 projector lamp contains mercury and should be properly recycled. Don’t throw it into regular garbage.

Step 7: Place the new Compaq 215464-001 projector lamp into the projector taking care not to touch the actual bulb. Oil residue from your fingers will cause black marks on the lamp when it starts to heat up.
Step 8: After making sure the Compaq 215464-001 lamp is in securely, press down the release latch to lock the lamp in place.
Step 9: Tighten the screw in the new lamp. You are now ready to reset the lamp timer.

Resetting the lamp timer counter

Compaq MP2810_projector_lamp_215464-001_menu

Once you have replaced the Compaq MP2810 projector lamp you will need to reset the lamp timer so the projector can accurately track the lamp hours. The projector will no work properly with the new lamp until the lamp timer has been reset.

To reset the lamp timer using the projector:

  • Press the Select button on the projector panel or the remote control. The Main menu will display on the projection screen. To select a function, press the Minus (-) button  to scroll down the Display menu. To reverse the scroll direction, press the Plus (+) button .
  • Scroll down to the Management selection.
  • Press Select to display the secondary menu.
  • Scroll down to Lamp Hours.
  • Press Select to display the third level menu.
  • Scroll down to Reset Lamp Hours.
  • Press Select.
  • Select Save and Return.

 

Learn more with Top tips for extending DLP projector lamp life.

Tagged with: , , ,

by avatarShelagh McNallyPosted on Posted in Articles, FixYourDLP, Projectors — No Comments ↓

top reasons to buy a DLP projector

Why buy a dlp projector?

A DLP projector is the best choice on the market offering competitive pricing and superior technology. Enjoy crisp, clear visuals with colors that pop along with easy of use with your DLP purchase.

Here are the top 5 reasons to purchase a DLP projector.

Ultra clear picture

Due to the technology using millions of tiny mirrors reflecting colors, video and graphics are sharper. The mirrors spaced less than a micron apart means there are fewer gaps between pixels so images are smooth with a film-like quality. You won’t see the pixilation effect that is present in LCD projectors. The DLP projector also has sealed optics making them better suited for dusty environments.

High resolution

DLP projectors deliver the highest available resolution – over 2 million pixels at 1920 x 1080. This translates into a full HDTV experience with outstanding picture and quality for either work or leisure viewing. With a DLP 1080p Projector you can experience the best HDTV programming, Blu-Ray discs, or video games available.

Brilliant Color

DLP projectors have a technological advantage over LCD projectors due to their sophisticated color wheel. DLP retain color accuracy because they simply reflect light onto the screen producing a crisp, clear and brilliant picture. Since there is no color decay or decreased legibility over time, your DLP projector will last for years.

Deeper blacks, brilliant whites

DLP Projectors provide a clear, sharp picture due to the high black and white contrasts. Most DLP projectors have contrast ratios of 2000:1—higher than most LCD projectors. Deeper blacks and more brilliant whites mean text is extremely readable—especially important in presentations that are text heavy presented in rooms with ambient light.

Portable and connected

DLP are small and compact due to their light engine with a single chip. Many weigh in at three-pounds or less making them very portable—especially important for business travel. They’ve been designed for easy set-up and quick connections to your computer.

 

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in Articles, FixYourDLP, Projector Lamp Replacement Guides, Projectors — No Comments ↓

Sanyo_PLV-Z1X_projectorLearn how maintenance can prolong projector lamp life

How to create a regular maintenance routine that will keep your projector working smoothly and prolong projector lamp life.

Cleaning the lens

A dirty projector lens can damped the quality of your image. Regular cleaning will help keep the picture bright. However, projector lenses are quite sensitive to scratching so approach with caution. The best way to clean your lens is to use a can of compressed air to get rid of any dust on the lens. Then gently wipe using dry microfiber lens cloth, found at any camera store. Keep your touch light and don’t press down too hard. If there is a stubborn streaks, then try using a lens cleaning solution.

Filter Cleaning

Like any electronic device, your 1080p projector is full of circuit board that creates heat. Every projector is cooled by air being pulled inside through a filter. This filter acts as a barrier to dirt and dust. When the filter gets clogged it the projector isn’t able to cool effectively and can overheat. A projector that is constantly running too hot burns through lamps faster. A projector that seriously melts down can have its circuit board and panels cooked. Keep your air filter clean.

Follow your instruction manual to learn how to change the filter in your particular model.

Check airflow

Don’t forget to check your ceiling-mounted projectors. They often get overlooked because they are not  easily accessible. Check to make sure your 108op projector has enough airflow around it. If the filters can get enough air intake, your projector will overheat. Check all the nuts and bolts to see if they need tightening/cleaning.

Change the lamp

Projector lamps tend to gradually get dimmer as they approach end of life. Every 1080p projector has a lamp tracking timer that will count the number of hours left. When it reaches a critical point, warning lights will start to blink and an on-screen message will ask you to replace the projector lamp.

When it’s time to replace the lamp be sure to buy genuine OEM lamps. We all like to save money but generic, “compatible” lamps should be avoided because of their inferior materials and workmanship. The few bucks you save can end up costing you much more in the long run when these counterfeit lamps damage your projector and compromise your health.

Read 7 tips for spotting counterfeits to learn more. Read about simple tips to extend the life of your projector and projector lamp.

 

Tagged with: , , ,

by avatarShelagh McNallyPosted on Posted in Articles, FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Home-Theater-screen

Projector screen set up is the final step for your home theater

It takes some planning to get your projector screen set up to get the perfect location. You’ll first have to consider the location of the projector. Most projectors are designed to have the middle of the lens project just a bit above the bottom edge of the screen.

You’ll want the ideal set up for your projector screen. The standard set up for the ideal height for a squared off image is to have the projector rest on a small table in front of the screen. Projectors with a vertical lens shift will have more flexibility and range. Since you won’t be able to sit in the path of the light beam, you may consider mounting the projector on the ceiling for more space.

The next step is finding the perfect location for your screen.

Placement is crucial

The bigger that projection, the better the picture but you will need to put the screen further away.  The minimum size the image can be is approximately 30″ (0.8 m) measured diagonally when the projector is roughly 4 feet (1.3 m) from the wall or screen. The largest the image can be is 500″ (12.7 m) when the projector is about 80.83 feet (24.64 m) from the wall or screen. Consult the drawing below as a guide.

screen set-up
Need help calculating the right size projector screen for your needs? Check out this online calculator.

Throw Distance and Screen Size

Each screen has an aspect ratio. The most common options are typically 16:9 or 4:3. Make sure your screen’s aspect ratio matches your projector’s for the best possible viewing experience.

The ideal screen size takes into consideration both the width and depth of the viewing room.  The biggest consideration for setting up your projector is the throw distance, which is the proportion of width and height of an image projected onto the screen.

It’s typically expressed as numbers, such as 4:3, but these numbers ARE NEVER the size of the screen. You will need to calculate the distance of the projector and then adjust it with the projector turned on.

throw-setting up screen

Learn more about projector screens

Tagged with: ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Compaq MP2800 projectorOur guide shows you how to replace the Compaq MP2800 projector lamp

When the Compaq MP2800 projector lamp has reached its end of life the message “”Lamp May Fail Soon –
Replacement Suggested” “displays on the projection screen. Replace the lamp immediately. Other warning signs may be a dim picture, color that appears washed and a image that is faded. The Compaq MP2800 projector uses the Compaq 215464-001 projector lamp. Be sure to invest in authentic.

Be sure to install an authentic Compaq MP2800 projector lamp. There is nothing more frustrating that having your Compaq MP2800 projector shut down as you are trying to use it.

Why should you avoid counterfeit lamps? With their shorter life and no safety guards to protect your eyesight, counterfeit lamps cause more long-term problems. From exploding inside projectors and damaging your projector beyond repair to the carcinogenic, toxic substitutes, counterfeit lamps end up costing you more money in the end.

Find this lamp on Amazon sold by these authorized dealers:

Compaq Lamp Replacement Kit for Mp2800 / 2810

In

Installing the replacement projector lamp

Compaq_2800_projector_lamp_215464-001_power

Step 1: Turn off the power to the projector by pressing the blue Standby button .
Step 2: Allow the Compaq MP2800 to cool down for at least 30 minutes.
Step 3: Disconnect the power cord.

 

Compaq Mp2800_projector_lamp_215464-001_power_replaceStep 4: Use a coin to loosen the screw  on the Compaq 215464-001 lamp module.
Step 5: On the front of the Compaq 215464-001 lamp slide up the latch to release it from the projector base.
Step 6: Pull out the Compaq 215464-001 lamp module.

NOTE: The used Compaq 215464-001 projector lamp contains mercury and should be properly recycled. Don’t throw it into regular garbage.

Step 7: Place the new Compaq 215464-001 projector lamp into the projector taking care not to touch the actual bulb. Oil residue from your fingers will cause black marks on the lamp when it starts to heat up.
Step 8: After making sure the Compaq 215464-001 lamp is in securely, press down the release latch to lock the lamp in place.
Step 9: Tighten the screw in the new lamp. You are now ready to reset the lamp timer.

Resetting the lamp timer counter

Compaq Mp2800_projector_lamp_215464-001_menu

Once you have replaced the Compaq MP2800 projector lamp you will need to reset the lamp timer so the projector can accurately track the lamp hours. The projector will no work properly with the new lamp until the lamp timer has been reset.

To reset the lamp timer using the projector:

  • Press the Select button on the projector panel or the remote control. The Main menu will display on the projection screen. To select a function, press the Minus (-) button  to scroll down the Display menu. To reverse the scroll direction, press the Plus (+) button .
  • Scroll down to the Management selection.
  • Press Select to display the secondary menu.
  • Scroll down to Lamp Hours.
  • Press Select to display the third level menu.
  • Scroll down to Reset Lamp Hours.
  • Press Select.
  • Select Save and Return.

 

Learn more with Top tips for extending DLP projector lamp life.

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

When it’s time for a new Dukane ImagePro 8771Dukane_ImagePro_8070_projector_Dukane_456-8767A_replacement_projector_lamp projector lamp

Warning sign

You can expect up to 2100 hours (up to 3100 hours in Eco mode) your Dukane ImagePro 8771 projector lamp before it needs to be replace.

Be sure to replace the lamp when you see the message “The lamp has reached the end of its usable life. Please replace the lamp.” It may also be time to replace the projector lamp if you notice the colors on screen have faded or become distorted.

If you have waited too long and the Dukane ImagePro 8771 goes into standby mode, press the HELP button on the remote control for 10 seconds to reset the lamp timer to zero. Replace the projector lamp immediately. Don’t wait until the last minute and have a Dukane ImagePro 8070 projector lamp on hand.

Reduce stress by going with authentic

It can be confusing finding the correct projector lamp for your Dukane ImagePro 8771 projector. Counterfeits, despite their bargain price, actually cost more in the long run. They should be avoided for the following reasons:

Find this lamp on Amazon from these authorized dealers:

 

Replacing the projector lamp

The Dukane ImagePro 8771 projector uses the Dukane 456-8767A projector lamp. Before installing a new projector lamp do the following safety steps:

  • Reduce the risk of electrical shock by disconnecting the power cord on the projector.
  • Reduce the risk of severe burns by allowing the projector to cool for at least 45 minutes. It should be cool to the touch.

Dukane_ImagePro_8771_Dukane_456-8767A_remove_projector_lamp_cover
Protect the Dukane ImagePro 8771 projector’s top surface by placing it face down on a soft surface. Turn the projector over and loosen the screws on the lamp cover.

Use a Philips screwdriver to push and release the tab. Push up and remove the lamp cover. NOTE: There is an interlock on this case to prevent the risk of electrical shock. Do not attempt to circumvent this interlock.

Dukane_ImagePro_8771_Dukane_456-8767A_remove_projector_lamp-2

Loosen the two screws securing the Dukane 456-8767A projector lamp. The screws are not removable so will start start freewheeling. Remove the lamp by grabbing onto the indents on the lamp and pulling up.

Never force the lamp out; pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Dukane 456-8767A projector lamp projector lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

Dukane_ImagePro_8771_Dukane_456-8767A_install_replacement_projector_lamp

Gently put in a new Dukane 456-8767A projector lamp and tighten the two screws to hold the lamp in place. Make sure the screws are secure as a loose screw can cause a bad connection while a over tightened screw may cause the lamp to notwork.

Dukane_ImagePro_8070_Dukane_456-8767A_cover_projector_lamp-4

Replace the lamp cover on the projector.

Slip the lamp cover back until it snaps into place.

Restart the projector to reset the lamp timer.

Resetting the lamp timer

It’s important to set the lamp timer so the Dukane ImagePro 8771 can accurately track the life of the newly installed Dukane 456-8767A projector lamp.
set_projector_lamp_timer
To reset the lamp timer go to the Dukane ImagePro 8771 Default Menu. Scroll down to Clear Lamp Hour Meter to reset the lamp timer.

Extend the life of the Dukane 456-8767A projector lamp:

Tagged with: ,

by avatarShelagh McNallyPosted on Posted in Articles, FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

interactive-whiteboard

Get the most out of your interactive whiteboard

An interactive whiteboard is an powerful instructional tool that can help any lesson come alive. These safety tips and precautions will help you get the most out of your interactive whiteboard.

Safety first

whiteboard

  • Don’t obstruct the cameras’ view of the interactive whiteboard’s surface or edges. Avoid magnets, stickers or adhesive tape on the interactive surface. Don’t rest any objects, including the pens  at the bottom of the interactive surface. This interferes with the corner cameras’ ability to detect your finger or pen tray tools.
  • Tell students not to look directly at the light beam from the projector as this can cause eye strain. Encourage them to keep their backs to the projector and before turning to face the class have them take a step sideways out of the projector’s beam.

Make sure that you don’t look directly into the projector’s beam. Keep your back to the class when you write over a projected image. Step to the side of the interactive whiteboard before you turn to face the class.

  • Tell students not to touch the projector because it can become extremely hot during normal operation.
  • Never let a student stand on a chair to reach the screen. If your students can’t reach the top of the interactive whiteboard, remount the wall-mounted unit at a lower position.

Preventing damage to the interactive whiteboard

whiteboard use of screenAlthough the SMART Board interactive whiteboard’s surface is very durable, take the following precautions to prevent damage to the interactive surface.

  • Avoid areas with high levels of dust, humidity or smoke.
  • Don’t use sharp or pointed objects, such as ballpoint pens or pointers, as writing tools.
  • Replace the pen nib when the nib wears out.
  • Low-odor dry-erase markers can be very difficult to erase. Use standard (high-odor) dry-erase markers but use them only in well-ventilated areas.
  • No adhesive tape on the interactive surface.
  • No abrasive erasers or harsh chemicals to clean the surface.
  • Never use compressed air to clean the interactive whiteboard’s cameras. The force of the air can damage them.

Keeping the writing surface clean

With proper care, the SMART Board interactive whiteboard will provide years of trouble-free service. Here are the best tips for keeping the interactive whiteboard working at its best:

interactive-whiteboard-student-teacher-anotate

    • Turn the interactive whiteboard off before you clean it so that you do not scramble the desktop icons or accidentally activate applications when you wipe the interactive surface.
    • To view dirt or streaks more easily, set the projector to standby (lamp off) mode.
    • Never  spray cleaner directly onto the interactive whiteboard’s surface.
    • To clean: spray a light amount of cleaner on a cloth and then gently wipe the interactive surface.
    • Clean your interactive whiteboard at least every six months.
    • Don’t allow excess cleaner to flow onto the frame’s reflective surfaces or into the pen tray slots.
    • The digital cameras located in the corners of the frame are protected from dust and dirt by windows. In extremely dusty environments, spray an alcohol-free household glass cleaner, such as Windex® cleaner, on a cotton swab and rub it gently on the windows. Don’t use compressed air to clean the cameras.


Cleaning the pen tray

interactive whiteboard cleaning pen toolIf the infrared sensors in the sides of the pen tools’ slots become obstructed by dirt, moisten a cotton swab with an alcohol-free household glass cleaner, such as Windex, and then carefully clean the infrared transmitter and receiver.

Tagged with:

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides, uncategorized — 4 Comments ↓

BenQ HT1075 projectorHow to replace the BenQ HT1075 projector lamp

Start off with authentic

Save yourself unnecessary headaches and purchase an authentic BenQ HT1075 projector lamp. Avoid counterfeit lamps.

You’ll need model BenQ 5J.J9H05.001 replacement lamp.

Find this lamp on Amazon from the following authorized dealers:

Why go authentic? Counterfeit “compatible” lamps may appear to be a bargain but in the long run end up costing more due to their shorter lamp life. They are prone to explosions and can put your eyesight at risk. Due to their substitute toxic materials and carcinogenic parts, the few dollars you will save are not worth it. Protect your health and keep your BenQ HT1075 working at optimum levels. Go with an authentic projector lamp.

End of life warning signs

Your BenQ HT1075 projector uses the BenQ 5J.J9H05.001 replacement projector lamp. When it’s time to replace the BenQ HT1075 projector lamp you’ll see a series warnings appear on screen.

BenQ_HT1075_projector_lamp_5J.J9H05.001_warnings

First warning: Install a new lamp for optimal performance. If the projector operates normally in Economic mode you may continue operating the
projector until the next hour lamp warning appears.
Press OK to dismiss the message.

 

 

Second Warning: Strongly recommend you to replace the lamp at this stage. The BenQ 5J.J9H05.001 lamp brightness
diminishes with use. This is normal lamp behavior. You can
replace the lamp whenever you notice that the brightness
level has significantly diminished.
Press OK to dismiss the message.

 

Final warning: The lamp MUST be replaced before the projector will operate normally.
Press OK to dismiss the message.

 

 

Follow these safety instructions before changing the lamp:

      • Reduce the risk of electrical shock by disconnecting the power cord on the BenQ HT1075 projector.
      • Reduce the risk of severe burns by allowing the projector to cool for at least 45 minutes. The projector should be cool to the touch.

Replacing the projector lamp

BenQ_HT1075_projector_lamp_5J.J9H05.001_cover-screwThe projector lamp cover is found on the side of the BenQ HT1075 projector.
Loosen the screw holding the projector lamp cover in place

BenQ_HT1075_projector_lamp_5J.J9H05.001_coverLift up the projector lamp cover. Put it to one side.

NOTE: The BenQ 5J.J9H05.001 projector lamp contains mercury and should not be thrown into regular garbage. It should be properly recycled. 

BenQ_HT1075_projector_lamp_5J.J9H05.001_screw

Loosen the screws that secures the lamp. Lift the handle so that it stands up.

BenQ_HT1075_projector_lamp_5J.J9H05.001_handleUse the handle to slowly pull the lamp out of the projector. Pulling it too quickly may cause the lamp to break and scatter  broken glass in the projector.

BenQ_HT1075_projector_lamp_5J.J9H05.001_insert_new

Insert the new BenQ 5J.J9H05.001 lamp into the projector taking care not to touch the actual bulb.

BenQ_HT1075_projector_lamp_5J.J9H05.001_tighten_screwTighten the screws on the new lamp Loose screw may cause a bad connection, which could result in malfunction. Do not over tighten the screw.

BenQ_HT1075_projector_lamp_5J.J9H05.001_replace_cover
Replace the lamp cover on the BenQ HT1075 projector. You are know ready to reset the lamp timer.

Resetting the lamp timer

After changing the lamp, you’ll need to rese the lamp timer. Do not reset if the lamp is not new or replaced as this could cause damage.

  • After the startup logo displays, resetting the lamp timer via the OSD menu.
    Under the Advanced OSD menu, go to System Setup : Advanced > Reset Lamp Timer/
  • Select RESET.
  • • Under the Basic OSD menu, if there’s no signal connected to the projector, go to Reset Lamp
    Timer and select Reset
  • If there are signals connected, go to Settings > Reset Lamp Timer and select Reset.
  • A “Reset Successfully” message displays to notify that the lamp time has been reset to “0”
Tagged with: , ,
Join the discussion on Facebook! All your questions, answered! The Screen & Projector Group