We're now Screen and Projector! For updated content, visit ScreenAndProjector.com and follow @screenandproj on social media!
Home › About Us › Page 6

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Epson-7500-projector Install a new Epson EMP-7500 projector lamp

This guide shows how to replace the Epson EMP-7500 projector lamp.

 When to replace

The Epson EMP-7500 projector lamp has an expected life of 200 hours. When it’s time to replace the lamp look for these warning signs:

  • The projected image gets darker or starts to deteriorate.
  • The projection lamp indicator flashes orange.
  • The message “LAMP REPLACE” appears on the screen

Finding the correct lamp

Protect your investment and buy a genuine Epson EMP-7500 projector lamp. You will need the Epson ELPLP06 replacement projector lamp.

You can find plenty of bargain generic lamps sold over the Internet. But Buyer Beware! These lamps can damage the sensitive and expensive mechanisms in your EMP-7500 projector.   They are also more prone to explosions due to the inferior materials and have a shorter life.

6 reasons to avoid counterfeit lamps:

Find this lamp on Amazon sold by these authorized dealers:

Installing a new lamp

Pre-installation preparation:

1. Turn off the projector power and wait for the cool-down period which is about two minutes. Disconnect the power cord after the two minutes is over.

2. Wait at least 30 minutes to one hour for the Epson EMP-7500 projector to cool internally before opening it up. It should be cool to the touch.

NOTE: Do not operate the projectors while the lamp is removed as this may result in malfunctions, fire hazard and other accidents.

 To install:

Epson_EMP-7500_projector_lamp_ELPLP06_lamp_cover

Use a screwdriver, coin, or similar object to loosen one retaining screw on the lamp cover. When the screw is loose, lift off the lamp cover. (You cannot remove this screw from the cover.)

Epson_EMP-7500_projector_lamp_ELPLP06_remove

Use a screwdriver, coin, or similar object to loosen two screws holding the lamp in position. (You cannot remove these screws.) Lift up the handle and pull out the Epson ELPLP06 projector lamp

NOTE: The Epson ELPLP06 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

Gently insert the new lamp by lowering it into position. Make sure it is inserted securely.
Tighten the screws you loosened. Replace the lamp cover and tighten the cover screw.
(Make sure the lamp cover is securely fastened. The projector will not run if the lamp cover is open.)

The lamps timer be automatically be reset to zero.

Extend lamp life

Extend the life of the newly installed Epson ELPLP06 with the following tips:

  • Keep your air filters clean to avoid overheating the projector.
  • Turn off the Epson EMP-7500 projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
  • Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
  • Learn more with Top tips for extending DLP projector lamp life.
Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Epson_EMP-5500 projector Clean the Epson EMP-5500 air filter

This guide shows how to clean or replace the Epson EMP-5500 air filter.

 When to replace

Clean the air filter at the bottom of the projector after every 100 hours of use. If it is not cleaned periodically, it can become clogged with dust, preventing proper ventilation.
This can cause overheating and damage the projector. Keeping the air filter clean will prolong the life of your projector.

Changing the filter

Follow these steps to replace or clean the air filter:

Epson_EMP-5500_clean_air_filter

  1. Turn off the projector and unplug the power cable.
  2. Turn the projector on its side so that the handle is on top and you can access the filter easily. Note: Standing the projector with the handle at the top keeps dust from getting inside the projector housing.
  1. Pull up the filter cover tab to release the filter cover. Remove the cover.
  1. The filter is attached to the inside of the filter cover. It is recommended that you use a small vacuum cleaner designed for computers and other office equipment to clean the filter. If you don’t have one, use a dry, lint-free cloth. If the dirt is difficult to remove or if the filter is torn, replace it.
  2. Replace the filter cover.
Tagged with: ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Epson_EMP-5500 projector Install a new Epson EMP-5500 projector lamp

This guide shows how to replace the Epson EMP-5500 projector lamp.

 When to replace

The Epson EMP-5500 projector lamp has an expected life of 200 hours. When it’s time to replace the lamp look for these warning signs:

  • The projected image gets darker or starts to deteriorate.
  • The projection lamp indicator flashes orange.
  • The message “LAMP REPLACE” appears on the screen

Finding the correct lamp

Protect your investment and buy a genuine Epson EMP-5500 projector lamp. You will need the Epson ELPLP06 replacement projector lamp.

You can find plenty of bargain generic lamps sold over the Internet. But Buyer Beware! These lamps can damage the sensitive and expensive mechanisms in your EMP-5500 projector.   They are also more prone to explosions due to the inferior materials and have a shorter life.

Even more troubling are the toxic, carcinogenic materials you are exposed to after installing one of these generic lamps. Installing a knock-off lamp will also void the guarantee on your EMP-5500 projector leaving you unprotected should anything happen after installation. Avoid hassles and buy authentic. Look for the seal of approval and buy from an authentic manufacturer. Learn how to protect yourself from counterfeit manufacturers.

Find this lamp sold on Amazon by these authorized dealers:

Find this lamp on Amazon from the following authorized dealers:

Installing a new lamp

Pre-installation preparation:

1. Turn off the projector power and wait for the cool-down period which is about two minutes. Disconnect the power cord after the two minutes is over.

2. Wait at least 30 minutes to one hour for the Epson EMP-5500 projector to cool internally before opening it up. It should be cool to the touch.

NOTE: Do not operate the projectors while the lamp is removed as this may result in malfunctions, fire hazard and other accidents.

 To install:

Epson_EMP-5500_projector_lamp_ELPLP06_lamp_cover

Use a screwdriver, coin, or similar object to loosen one retaining screw on the lamp cover. When the screw is loose, lift off the lamp cover. (You cannot remove this screw from the cover.)

Use a screwdriver, coin, or similar object to loosen two screws holding the lamp in position. (You cannot remove these screws.) Lift up the handle and pull out the Epson ELPLP06 projector lamp

NOTE: The Epson ELPLP06 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

Gently insert the new lamp by lowering it into position. Make sure it is inserted securely.
Tighten the screws you loosened. Replace the lamp cover and tighten the cover screw.
(Make sure the lamp cover is securely fastened. The projector will not run if the lamp cover is open.)

The lamps timer be automatically be reset to zero.

Extend lamp life

Extend the life of the newly installed Epson ELPLP06 with the following tips:

  • Keep your air filters clean to avoid overheating the projector.
  • Turn off the Epson Epson EMP-5500 projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
  • Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
  • Learn more with Top tips for extending DLP projector lamp life.

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Sanyo Sanyo PLC-XT15A projector, POA-LMP59 service parts no 610 305 560Replacing the Sanyo PLC-XT15A projector lamp 

The lifespan of your Sanyo PLC-XT16 projector lamp lamp varies depending on how much the projector is used and if the filters are cleaned regularly. When it’s time to replace the lamp, the LAMP REPLACE indicator will flash yellow on the top of the Sanyo PLC-XT15A projector.

Follow our step-by-step guide for easy installation of a new Sanyo PLC-XT15A projector lamp.

Buying the right lamp

Prolong the life of your Sanyo PLC-XT15A projector lamp by installing an original projector lamp. Generic lamps look like a great bargain but have a number of problems.

6 reasons to avoid counterfeit lamps:

Find this lamp sold on Amazon by the following authorized dealers:

Installing the Sanyo POA-LMP59

Sanyo_PLC-XT15A_lamp_cover_POA-LMP59_service_parts_no61030556021. Turn off the projector and unplug the AC cord. Allow the  Sanyo PLC-XT15A projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures.

2. The lamp cover is Underneath the Sanyo PLC-XT15A projector you’ll find the Lamp Cover. Gently turn the projector upside down protecting the top of the project and lsen the cover screw.

2. Remove the two screws on either side of each the Sanyo POA-LMP59  projector lamp. Grab the handle on the lamp cage and gently lift out the lamp. Place to one side. Don’t throw this lamp into the regular garbage as it contains mercury — send it to a local recycling program where it can be disposed of properly.

3. Take the new Sanyo POA-LMP59  lamp cage by the handle and gently maneuver it into place. Sanyo_PLC-XT15A_lam_ assembly_ POA-LMP59_service_part_no6103055602

4. Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb. The lamp should slide in easily – don’t force it. Once the lamp is in, tighten the two screws on the Lamp Assembly.

5. Replace the Lamp Hazard Cover and tighten the screw.

6. Re-connect the power cord and turn on the Sanyo PLC-XT15A projector in order to reset the Lamp Replace Counter.

NOTE: Your old Sanyo POA-LMP59 lamp should always be properly recycled. These lamps contain mercury and can’t be placed into common garbage.

Resetting the Lamp Replace Counter

The Lamp Replacement Counter always needs to be reset after installing a new projector lamp so it can track the age of your lamp and turn the Lamp Replace indicator on when the end of life for the Sanyo POA-LMP59 is approaching.
Sanyo_PLC-XT15A_lamp_replace_counter_POA-LMP59_service_parts_no6103055602

  • Press the MENU Button to display the MAIN MENU. Press the POINT LEFT/RIGHT button and scroll right to select SETTING.
  • Press the SELECT button to display the SETTING DISPLAY menu.
  • Press the POINT DOWN button (a red arrow will appear).
  • Move the red arrow to the LAMP AGE and then press the SELECT button.
  • The message “Lamp replace counter reset?” appears. Move the arrow down to YES and press the SELECT button.
  • Move the arrow to QUIT and press the SELECT button.

Extend the projector lamp life

Extend the life of your newly installed Sanyo POA-LMP59 by following these helpful tips:

  • Wait at least five minutes before turning the Sanyo PLC-XT16 off.
  • Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
  • Cleaning the air filter regularly will also prolong the life of the and prevent the Sanyo PLC-XT16 projector from overheating.
  • Use the ECO setting to reduce the brightness of the lamp and have a low consumption mode.
Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Sanyo PLC-XT10A projector, POA-LMP59 service parts no 610 305 560Replacing the Sanyo PLC-XT10A projector lamp

The lifespan of your Sanyo PLC-XT16 projector lamp lamp varies depending on how much the projector is used and if the filters are cleaned regularly. When it’s time to replace the lamp, the LAMP REPLACE indicator will flash yellow on the top of the Sanyo PLC-XT10A projector.

Follow our step-by-step guide for easy installation of a new Sanyo PLC-XT10A projector lamp.

Buying the right lamp

The Sanyo PLC-XT10A projector lamp uses the Sanyo POA-LMP59 (610 305 5602) from an authorized dealer and get the best lamp for your Sanyo PLC-XT10A projector.  Beware of cheaper knock-off versions that can damage the sensitive mechanisms in your Sanyo PLC-XT10A. These counterfeit lamps are often sold at discounted prices and may appear to be a good deal. But they actually have a shorter life span and may be prone to exploding due to their inferior materials and worksmanship. Installing generic lamps also voids your warranty leaving you unprotected should something be damaged.

Find this lamp sold on Amazon by the following authorized dealers:

Installing the Sanyo POA-LMP59

Sanyo PLC-XT16 lamp cover, POA-LMP59 service parts no 610 305 56021. Turn off the projector and unplug the AC cord. Allow the Sanyo PLC-XT10A projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures.

2. The lamp cover is Underneath the Sanyo PLC-XT10A projector you’ll find the Lamp Cover. Gently turn the projector upside down protecting the top of the project and lsen the cover screw.

2. Remove the two screws on either side of each the Sanyo POA-LMP59  projector lamp. Grab the handle on the lamp cage and gently lift out the lamp. Place to one side. Don’t throw this lamp into the regular garbage as it contains mercury — send it to a local recycling program where it can be disposed of properly.

3. Take the new Sanyo POA-LMP59  lamp cage by the handle and gently maneuver it into place. Sanyo PLC-XT16 lamp assembly, POA-LMP59 service parts no 610 305 5602

4. Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb. The lamp should slide in easily – don’t force it. Once the lamp is in, tighten the two screws on the Lamp Assembly.

5. Replace the Lamp Hazard Cover and tighten the screw.

6. Re-connect the power cord and turn on the Sanyo PLC-XT16 projector in order to reset the Lamp Replace Counter.

NOTE: Your old Sanyo POA-LMP59 lamp should always be properly recycled. These lamps contain mercury and can’t be placed into common garbage.

Resetting the Lamp Replace Counter

The Lamp Replacement Counter always needs to be reset after installing a new projector lamp so it can track the age of your lamp and turn the Lamp Replace indicator on when the end of life for the Sanyo POA-LMP59 is approaching.
Sanyo PLC-XT16 lamp replace counter, POA-LMP59 service parts no 610 305 5602

  • Press the MENU Button to display the MAIN MENU. Press the POINT LEFT/RIGHT button and scroll right to select SETTING.
  • Press the SELECT button to display the SETTING DISPLAY menu.
  • Press the POINT DOWN button (a red arrow will appear).
  • Move the red arrow to the LAMP AGE and then press the SELECT button.
  • The message “Lamp replace counter reset?” appears. Move the arrow down to YES and press the SELECT button.
  • Move the arrow to QUIT and press the SELECT button.

Extend the projector lamp life

Extend the life of your newly installed Sanyo POA-LMP59 by following these helpful tips:

  • Wait at least five minutes before turning the Sanyo PLC-XT16 off.
  • Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
  • Cleaning the air filter regularly will also prolong the life of the and prevent the Sanyo PLC-XT16 projector from overheating.
  • Use the ECO setting to reduce the brightness of the lamp and have a low consumption mode.
Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

ProjectionDesign Action! Model One projectorReplacement ProjectionDesign Action Model Five projector lamp

Your ProjectionDesign Action Model Five projector uses the ProjectionDesign 400-0003-00 Projector Lamp. Be sure to buy your ProjectionDesign Action Model 1 projector lamp from an authorized dealer to keep your projector working properly.

Find this replacement lamp on Amazon from the following authorized dealers:

 

6 reasons to avoid counterfeit lamps:

End of life warning signs

Projection_Design_Action_Mode_Five_l400-0003-00 Projector Lamp_warningWhen it’s time to replace the ProjectionDesign Action Model 5 projector lamp the projector lamp status indicators will turn red. Other warning signs may include a darker screen or colors that appear washed out or an deteriorating screen image.

How to replace

Before installation follow these important safety steps:

  • Turn off the ProjectionDesign Action Model 5 projector:
  • Unplug the AC cord.
  • These projectors operate under high temperatures and there is a risk of burning if the projector has not cooled enough. Allow the ProjectionDesign Action Model One to cool for one hour. It should be cool to the touch.

Projection_Design_Action_ModeL_Five_l400-0003-00 Projector Lamp_cover

Projection_Design_Action_Mode_Five_l400-0003-00 Projector Lamp_loosen_screws

Remove the two screws from the ProjectionDesign Action Model 1 projector lamp cover. Remove the projector lamp cover.

Loosen the two screws holding the ProjectionDesign 400-0003-00 projector lamp in place.

 

Projection_Design_Action_Mode_Five_l400-0003-
Turn the lamp knob counter clockwise to the unlocked position.

NOTE: The ProjectionDesign 400-0003-00 projector lamp contains mercury and should not be thrown into regular garbage. Recycle this lamp!

 

Projection_Design_Action_Mode_Five_l400-0003-00 Projector Lamp_insert

Pull out the ProjectionDesign 400-0003-00 projector lamp.
Tighten the screws on the projector lamp lid.

Projection_Design_Action_Mode_Five_l400-0003-00 Projector Lamp_replacement
Place the new ProjectionDesign 400-0003-00 projector lamp into the projector. Take care not to touch the actual bulb. Oil from your fingerprints will create black spots onto the bulb.
Projection_Design_Action_Mode_Five_l400-0003-00 Projector Lamp_tighten
Tighten the screws on the projector lamp. Turn the lamp knob
clockwise to the locked position.
Put the lamp cover back on and tighten the two screws holding the cover in place.

 

 

Resetting the projector lamp timer

Each time you replace the ProjectionDesign 400-0003-00 projector lamp you will need to reset the ProjectionDesign Action Model 1 lamp timer so the projector can accurately track the lamp hours. To reset the:
  • Open the MENU option. Press ENTER.
  • Scroll down to the UTILTIES submenu.
  • Press reset the lamp time.

Extending the projector lamp life

  • Use the Eco Mode for more lamp hours.
  • Keep your air filters clean to avoid overheating the projector.
  • Make sure there is enough airflow around the ProjectionDesign Action Model 1.
  • Learn more with Top tips for extending DLP projector lamp life

Learn more tips for extending lamp life.

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

ASK Proxima C160/C180, ASK Proxima SP-LAMP-017

How to install a new ASK Proxima C160 projector lamp

When the LED light is blinking red it’s time to replace the ASK Proxima C160 projector lamp. You may also see a “Replace Lamp” message on the screen. Don’t wait to replace the ASK Proxima SP-LAMP-017. The projector will turn off once the lamp life is approaching end of life.

The importance of authentic lamps

Prolong the life of your ASK Proxima C160 projector by installing an original ASK Proxima SP-LAMP-017 projector lamp. Generic lamps look like a great bargain but have a number of problems:

7 tips for spotting counterfeits.

Buy this lamp on Amazon from the following authorized dealers:

Aurabeam Replacement Lamp for Ask Proxima SP-LAMP-017 Projector with Housing
SpArc Bronze for Ask Proxima SP-LAMP-017 Projector Replacement Lamp with Housing

Replacing the  lamp

ASK Proxima C160/C180 lamp door, ASK Proxima SP-LAMP-017

  • Turn the ASK Proxima C160 projector off and unplug the AC cord. Wait 60 minutes until the projector is fully cooled. These projectors work under extremely high heat and there is danger of burning yourself if you don’t let the projector cool off.
  • Turn the ASK Proxima C160 projector upside down.

ASK Proxima C160/C180 door open, ASK Proxima SP-LAMP-017

  • Loosen the screw holding the lamp cover in place.
  • Pry the lamp door off using the tip of the screw driver.

 

ASK Proxima C160/C180 lamp cage, ASK Proxima SP-LAMP-017

Be sure to send the used lamp to a proper recycling facility. Don’t throw the used lamp into the regular garbage.

ASK Proxima C160/C180 lamp cage, ASK Proxima SP-LAMP-017

  • Put the new ASK Proxima SP-LAMP-017 lamp into the projector making sure it’s properly seated.
  • Replace the two screws on the lamp module.
  • Replace the door and tighten the screw.
  • Plug in the power cable and turn the projector back on. You are ready to reset the lamp timer.

Resetting the lamp timer

Once you have replaced the ASK Proxima SP-LAMP-017 it’s extremely important to reset the lamp timer. You want the the lamp life  to properly track the hours left for your ASK Proxima SP-LAMP-017. Otherwise you run the risk of the ASK Proxima C160 suddenly shutting down.
There are two ways of resetting the lamp timer.

Using the projector:

  • Press the decrease volume button on the remote first, followed by the increase volume button.
  • The LED light will blink green when the lamp hour has been reset.

ASK Proxima C160/C180, ASK Proxima SP-LAMP-017Using the menu:

  • Open the MAIN menu.
  • Navigate to the SETTINGS menu. Press SELECT.
  • Scroll down to the SERVICE menu option. Press SELECT.
  • Scroll down to the LAMP RESET option. Press SELECT.

 

 

Learn more with Top tips for extending DLP projector lamp life.

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

ASK Proxima C160/C180, ASK Proxima SP-LAMP-017

How to install a new ASK Proxima C180 projector lamp

When the LED light is blinking red it’s time to replace the ASK Proxima C180 projector lamp. You may also see a “Replace Lamp” message on the screen. Don’t wait to replace the ASK Proxima SP-LAMP-017. The projector will turn off once the lamp life is approaching end of life.

ASK Proxima C160/C180 ABOUT Menu, ASK Proxima SP-LAMP-017

Find out how many hours have been used on the ASK Proxima SP-LAMP-017 through the ABOUT option found on the main MENU.
nbsp

The importance of authentic lamps

Prolong the life of your ASK Proxima C180 projector by installing an original ASK Proxima SP-LAMP-017 projector lamp. Generic lamps look like a great bargain but these knock-off lamps are created with inferior materials making them susceptible to explosions when installed and they can damage the sensitive components in your ASK Proxima C180 projector. They’ve created using toxic substances such as Krypton-85 (which is carcinogenic to humans). “Compatible” lamps also  have a shorter life span so can actually cost more money in the long run.

Buying authentic guarantees a projector lamp created with genuine, non-hazardous materials by the original manufacturer. These lamps come with money-back guarantee and keeps your warranty entact. It’s worth the few extra dollars to eliminate potential problems and have a lamp built to work properly with your ASK Proxima C180 sensitive mechanisms. Learn more about spotting dangerous projector lamps by reading our article: 7 tips for spotting counterfeits.

Buy this lamp on Amazon from the following authorized dealers:

Aurabeam Replacement Lamp for Ask Proxima SP-LAMP-017 Projector with Housing
SpArc Bronze for Ask Proxima SP-LAMP-017 Projector Replacement Lamp with Housing

Replacing the  lamp

ASK Proxima C160/C180 lamp door, ASK Proxima SP-LAMP-017

  • Turn the ASK Proxima /C180 projector off and unplug the AC cord. Wait 60 minutes until the projector is fully cooled. These projectors work under extremely high heat and there is danger of burning yourself if you don’t let the projector cool off.
  • Turn the ASK Proxima C180 projector upside down.

ASK Proxima C160/C180 door open, ASK Proxima SP-LAMP-017

  • Loosen the screw holding the lamp cover in place.
  • Pry the lamp door off using the tip of the screw driver.

 

ASK Proxima C160/C180 lamp cage, ASK Proxima SP-LAMP-017

Be sure to send the used lamp to a proper recycling facility. Don’t throw the used lamp into the regular garbage.

ASK Proxima C160/C180 lamp cage, ASK Proxima SP-LAMP-017

  • Put the new ASK Proxima SP-LAMP-017 lamp into the projector making sure it’s properly seated.
  • Replace the two screws on the lamp module.
  • Replace the door and tighten the screw.
  • Plug in the power cable and turn the projector back on. You are ready to reset the lamp timer.

Resetting the lamp timer

Once you have replaced the ASK Proxima SP-LAMP-017 it’s extremely important to reset the lamp timer. You want the the lamp life  to properly track the hours left for your ASK Proxima SP-LAMP-017. Otherwise you run the risk of the ASK Proxima C180 suddenly shutting down.
There are two ways of resetting the lamp timer.

Using the projector:

  • Press the decrease volume button on the remote first, followed by the increase volume button.
  • The LED light will blink green when the lamp hour has been reset.

ASK Proxima C160/C180, ASK Proxima SP-LAMP-017Using the menu:

  • Open the MAIN menu.
  • Navigate to the SETTINGS menu. Press SELECT.
  • Scroll down to the SERVICE menu option. Press SELECT.
  • Scroll down to the LAMP RESET option. Press SELECT.

 

 

Learn more with Top tips for extending DLP projector lamp life.

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides, uncategorized — No Comments ↓

Epson EB-955W projector lampInstalling a new Epson EX7220 air filter is an important maintenance routine

The Epson EX7220 air filter should be replaced regularly. Allowing dust particles to collect in the projector can cause it to overheat and cause the lamp to explode.

Cleaning the Air Filter and Vents

Clean the projector’s air filter or vents if they get dusty, or if you see a message telling you to clean them.

      1. Turn off the projector and unplug the power cord.
      2. Gently remove the dust using a small vacuum designed for computers or a very soft brush (such as a paintbrush).Note: You can remove the air filter so you can clean both sides of it. Do not rinse the air filter in water, or use any detergent or solvent to clean it.Caution:
        Do not use canned air. The gases may leave a flammable residue or push dust and debris into the projector’s optics or other sensitive areas.
      3. If dust is difficult to remove or the air filter is damaged, replace the air filter.

Replacing the Air Filter

    • You need to replace the air filter in the following situations:

      • After cleaning the air filter, you see a message telling you to clean or replace it
      • The air filter is torn or damaged

You can replace the air filter while the projector is mounted to the ceiling or placed on a table.

    1. Turn off the projector and unplug the power cord.
    2. Carefully open the air filter cover.
    3. Pull the air filter out of the projector.

      Note: Air filters contain ABS resin and polyurethane foam. Dispose of used air filters according to local regulations.
    4. Place the new air filter in the projector as shown and push gently until it clicks into place.
    5. Close the air filter cover.

Need to replace the Epson EX7220 projector lamp? Follow our guide.

Tagged with: ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — 4 Comments ↓

Optoma_HD141X_projectorWhy change the Optoma HD141X air filter?

Optoma HD141X air filter should be replaced regularly, Keeping this The Optoma HD141X air filter properly is an important part of keeping the projector running.
Air filters stop dust from accumulating on the optical elements inside the projector. Allowing dust particles to collect in the projector can cause it to overheat and cause the lamp to explode. Cleaning and replacing the  Optoma HD141X should be done regularly every three months. If the projector is used in a dusty environment it should be changed more frequently.

Replacing the filter

TO start
  • Switch the power off button on the remote control or on the keypad of the projector.
  • Disconnect the power cord.
  • Slowly remove the dust cover. Don’t force the lid off as this could damage the lid.
 Gently clean dust from the filters using a small brush or small computer vacuum.
If the filters are very dirty you will need to replace them.
Re-install the filter cover.
After checking for filter, turn the projector back on.
Tagged with: ,
Join the discussion on Facebook! All your questions, answered! The Screen & Projector Group