We're now Screen and Projector! For updated content, visit ScreenAndProjector.com and follow @screenandproj on social media!
Home › About Us › Page 55

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — 2 Comments ↓

Optoma_PRO150S_projector_BL-FU185A_projector_lamp

This how-to guide will help you install a new Optoma PRO150S projector lamp

When it’s time to replace the Optoma PRO150S projector lamp you may also notice the Lamp-LED light flashing red or the picture quality starting to get poor resolution with washed out colours.

Optoma_PRO150S_lamp_replacement_warning_BL-FU185A_projector_lampYou will also see the projector lamp warning message flash on screen. This means you have no more than 30 hours before the bulb will burn out.

Change the Optoma BL-FU185A projector lamp in your Optoma PRO150S immediately.

Authentic Optoma PRO150S projector lamp are critical!

You’ll want the best projector lamp for your Optoma PRO150S and that means buying directly from an authorized manufacturer. Look for the seal of approval. Remember you get what you pay for.

6 reasons to avoid generic lamps:

Learn how to spot the copycat lamps posing as authentic lamps.

Find this lamp sold on Amazon by these authorized dealers:

Installing the Optoma PRO150S projector lamp

Your Optoma PRO150S projector uses the Optoma BL-FU185A  projector lamp follow these crucial safety tips to prevent injury to yourself or the projector:

  • Switch off the power to the Optoma PRO150S projector by pressing the Power/Standby button.
  • Disconnect the power cord.
  • Allow the projector to cool down for at least 30 minutes. If should be cool to the touch. These projectors run using high temperatures and you can burn yourself badly if you don’t allow the projector to cool down.

Optoma_PRO150S_install_replacement_BL-FU185A_projector_lamp1. Use a screwdriver to undo the two screws holding the lamp cover in place. The screws on the lamp cover and the lamp cannot be removed.

2. Remove the lid and place to one side. Don’t lose the lid as the PRO150S projector will not turn back on until the lamp cover has been properly installed.

3. Remove the two screws holding the Optoma BL-FU185A  projector lamp in place.

Note: The used Optoma BL-FU185A  projector lamp contains mercury and should be properly recycled. Don’t throw it into regular garbage.

4. Lift up the wire handle on the Optoma BL-FU185A projector lamp and slowly remove it from the projector. Be careful not to bang the lamp against the projector as this may case the bulb to break. Learn what to do if the lamp has exploded inside the projector.

Install the new Optoma BL-FU185A projector lamp:

  • Remove the new Optoma BL-FU185A projector lamp from its packaging.
  • Taking care not to touch the actual bulb, lift up the handle on the new lamp and insert it gently into the Optoma PRO150S projector.
  • Tighten the two screws on the projector lamp.
  • Replace the lamp cover and tighten its two screws. Reset the lamp timer.

Reset the Lamp Replacement Timer

The Optoma PRO150S projector has an automatic lamp timer that tracks the numbers of hours left in the projector lamp. When the Optoma BL-FU185A  projector lamp is approaching end of life, the lamp replacement timer will trigger the warning system. If you don’t reset the lamp replacement timer you run the risk of the projector lamp being used beyond its recommended life and possibly exploding in the projector.

Optoma_PRO150S__reset_lamp_timerBL-FU185A_projector_lampTo reset the Lamp Replacement Timer:

  • Turn on the projector.
  • Using the remote press MENU
  • Select OPTIONS
  • Select LAMP SETTINGS
  • Select LAMP RESET
  • Select YES.
  • Press MENU to exit.

Extend the life of the Optoma BL-FU185A projector lamp:

  • Chose the “STD” mode to to dim the projector lamp and lower power consumption. This will extend the lamp life by up to 130%.
  • Keep your air filters clean to avoid overheating the projector.
  • Every 24 hours, turn off the projector and let it stand for 1 hour
  • Make sure there is enough airflow around the Optoma PRO150S projector particularly if it’s been permanently mounted.
  • Learn more with Top tips for extending DLP projector lamp life.

Green your Optoma PRO150S projector

Optoma-BL-FU185A_replacement_bulb_training_videoThe Optoma PRO150S projector has the option of re-using the existing lamp cage and replacing only the actual bulb. You recycle and reduce waste this way. Watch our Optoma BL-FU185A training video to learn more.

Tagged with: , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Your guide for replacing the Viewsonic PJD6241 projector lamp.

Note: Viewsonic recommends you contact a service rep before changing the Viewsonic PJD6241 projector lamp.

End of life warning signs:

  • Power LED lamp light flashes bright blue
  • Lamp LED becomes bright red.
  • A warning message will also flash onscreen.
  • Authentic lamps are critical!

Find this lamp on Amazon sold by these authorized dealers:

 

ViewSonic-PJD6241_projector_change_RLC-049-Projector-LampInstalling the Viewsonic RLC-049 lamp

Before replacing the Viewsonic RLC-049 projector follow these crucial safety tips to prevent injury to yourself or the projector:

  • NEVER change the lamp unless the Viewsonic PJD6241 projector is cool to the touch as it operates under high temperatures and you can burn yourself quite badly.
  • Switch off the power to the Viewsonic PJD6381 projector.
  • Disconnect the power cord.

1. Use a screwdriver to undo the screw holding the Viewsonic RLC-049 lamp cover in place. Remove the lamp cover, being careful not to lose the screws.

2. Slide the lid — slowly — off the projector. and place to one side. Don’t lose the lid because the Viewsonic PJD6241 projector will not turn back if the lamp cover hasn’t been installed properly.

3. Remove the two screws holding the Viewsonic RLC-049 lamp in place.

Note: The used Viewsonic RLC-049 lamp contains mercury and should be properly recycled. Don’t throw it into regular garbage.

4. Grab the Viewsonic RLC-049 lamp by it’s side edges and slowly lift the lamp put of the projector. Be careful not to bang the lamp against the projector as this may case the bulb to break.

Reset the Lamp Replacement Timer

The Viewsonic PJD6381 projector has an automatic lamp timer that tracks the numbers of hours left in the lamp. Each time you install a new lamp, you’ll need to to reset the lamp timer to know how many hours are left and when to change the bulb.

ViewSonic_PJD6381_lamp_reset_menuRLC-049_lamp

To reset the Lamp Replacement Timer:

  • Turn on the projector.
  • Using the remote press MENU
  • Scroll to the main menu
  • Select Settings
  • Scroll down to Lamp Hours
  • Press the arrow button to move to the right,
  • Select YES.
  • Press MENU to exit.

Your Viewsonic PJD6241 is a sophisticated piece of technology with sensitive optics stored inside it’s main operating system. It doesn’t make sense to buy a cheap, reproduction lamp that is inferior to authentic OEM lamps. These Original Equipment Manufacturer (OEM) lamps are created using the proper materials and with the proper fittings. Look for the seal of approval that lets you know you are buying an authentic projector lamp.

6 reasons to avoid generic lamps:

Learn how to spot the copycat lamps posing as authentic lamps.

Learn what to do if the lamp has exploded inside the projector.

  • Remove the new Viewsonic RLC-049 from its packaging.
  • Taking care not to touch the actual bulb, lift up the handle on the new lamp and insert it gently into the Viewsonic PJD6241 projector.
  • Tighten the two screws on the lamp.
  • Replace the lamp cover and tighten its two screws. Reset the lamp timer.

Extend the life of the Viewsonic RLC-049 by setting the Viewsonic PJD6241 to Eco Mode. This lowers the brightness of the projector and makes the lamp last longer. Read about other tips for extending the lamp life in your Viewsonic PJD6241.

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Sharp_XG-P20_projector_Sharp_BQC-XGP20X_RLMPF0072CEZZ_projector_lampWhen it time to replace the Sharp XG-P20XU projector lamp use this guide.

Know the warning signs

Depending on the usage and maintenance, the Sharp XG-P20XU projector lamp operates for approximately 1,000 hours. At 900 hours, the projector LAMP REPLACEMENT indicator lights up red. The LAMP icon flashes yellow in the lower-left corner of the picture.  If you notice a significant deterioration of the picture and color quality, you can replace it the Sharp BQC-XGP20X//1 projector lamp.

You can see the hours remaining for lamp usage by checking the On-screen Display option found on the Main Menu.

Sharp_XG-P20_projector_Sharp_BQC-XGP20X_RLMPF0072CEZZ_projector_lamp_warning_lights Replace the Sharp BQC-XGP20X//1 projector lamp immediately at 900 hours and don’t wait! Should the projector lamp explode, learn what to do.

Buying the right projector lamp

The Internet has been flooded with generic projector lamps stating they are “compatible” with Sharp XG-P20XU projector. However, these projector lamps don’t offer much savings and come with many problems that can affect the life of your projector.

Consider the source before purchasing.

Six reasons to avoid generic lamps:

Learn How to buy an authentic projector lamp.

Find this lamp sold on Amazon by these authorized dealers:

Installing the Sharp BQC-XGP20X//1 projector lamp

Before replacing the Sharp BQC-XGP20X//1 projector lamp follow these important safety tips:

  • Switch off the power to the Sharp XG-P20XU projector by pressing the Power button.
  • Disconnect the power cord.
  • Allow the projector to cool down for at least one hour. If should be cool to the touch. The Sharp XG-P20XU projector uses high temperatures and you can burn yourself badly if you don’t allow the projector to cool down.

Sharp_XG-P20_projector_Sharp_BQC-XGP20X_RLMPF0072CEZZ_projector_lamp_cover_removalTurn over the Sharp XG-P20XU projector onto a soft service and loosen the user service screw that holds the projector lamp cover on place. Slide the cover off away from the projector and place it to one side.

Sharp_XG-P20_projector_Sharp_BQC-XGP20X_RLMPF0072CEZZ_projector_lamp_screws

Remove the screws holding the Sharp BQC-XGP20X//1 projector lamp in place. Grab the wire handle and gently pull the Sharp BQC-XGP20X//1 projector lamp out.

 

Sharp_XG-P20_projector_Sharp_BQC-XGP20X_RLMPF0072CEZZ_projector_lamp_insert_new

Take the new Sharp BQC-XGP20X//1 projector lamp and press it firmly into the lamp cage compartment. Be careful not to touch the actual bulb as the oil from your fingers left on the lamp will burn black holes onto the lamp that appear on screen.

Note: The used Sharp BQC-XGP20X//1 projector lamp contains mercury and should be properly recycled. Don’t throw it into regular garbage.

Sharp_XG-P20_projector_Sharp_BQC-XGP20X_RLMPF0072CEZZ_projector_lamp_replace_cover Fasten the securing screws. Slide the lamp cage cover back on in the direction of the projector. Then tighten the user service screw.

Reset the lamp timer and clean the air filters.

To reset the Sharp XG-P20XU projector lamp timer:

While pressing DOWN arrow, RIGHT arrow and ENTER on the projector, press POWER ON on the projector.

“LAMP 0000H” is displayed, indicating that the lamp timer is reset. Sharp_XG-P20_projector_Sharp_BQC-XGP20X_RLMPF0072CEZZ_projector_lamp_reset_timer_message

 

 

To clean the Sharp XG-P20XU air filter

Sharp_XG-P20_projector_Sharp_BQC-XGP20X_RLMPF0072CEZZ_projector_lamp_remove_air_dirty_filterSharp_XG-P20_projector_Sharp_BQC-XGP20X_RLMPF0072CEZZ_projector_lamp_change_dirty_air_filter

Press the air filter tab and lift open the filter cover away from the projector.

Grasp the air filter between your fingers and lift it off the filter cover.

Vacuum the dust off the air filter – DO NOT WASH.

Put the air filter back on the filter frame.

Insert the tab on the end of the filter cover into the filter cover opening and press the filter cover into position.

 

Extend the life of the Sharp BQC-XGP20X//1 projector lamp:

  • Chose the “STD” mode to to dim the projector lamp and lower power consumption. This will extend the lamp life by up to 130%.
  • Keep your air filters clean to avoid overheating the projector.
  • Every 24 hours, turn off the projector and let it stand for 1 hour
  • Make sure there is enough airflow around the Sharp XG-P20XU projector particularly if it’s been permanently mounted.
  • Learn more with Top tips for extending DLP projector lamp life.

Go for a green alternative!

Sharp_BQC-XGP20X_1_projector_lamp

If you are looking for an even more eco-friendly option for your Sharp XG-P20XU projector why no consider replacing only the projector bulb and not the entire projector lamp? You recycle the lamp cage and reduce waste. Our step-by-step video shows you how.

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Vivitek_d825_projector_Vivitek_1000055_projector_lampNo need to call a service technician to change your Vivitek D825EX projector lamp.

Our guide will walk you through the change.

Be prepared

When you notice the Power LED flashing 5 times consecutively, your Vivitek D825EX projector lamp is reaching its end of life and needs to be replaced immediately. Don’t get caught short. Have a lamp ready and waiting.

Be sure the purchase an authentic Vivitek 1000055-A (5811100760S) projector lamp for your Vivitek D825EX projector. Although generic lamps seem like a bargain, avoid knock-off “compatible” lamps. You get what you pay for and in the case of generic lamps it’s usually a long list of problems:

Save yourself unnecessary headaches and buy an authentic projector lamo from a recognized dealer. You’ll be getting a far superior product with a replacement guarantee and tech support.

Find this lamp on Amazon sold by these authorized dealers:

Replacing the 1000055-A projector lamp

Before changing the projector lamp:

  • Reduce the risk of electrical shock by disconnecting the power cord on the Vivitek D825EX projector.
  • Reduce the risk of severe burns by allowing the projector to cool for at least 45 minutes.

Vivitek_D825EX_projector_1000055_projector_lamp_replacemenVivitek_D825EX_projector_1000055_remove_projector_lamp_cover

  • Remove the two captive screws holding the lamp cover place.
  • Remove the lamp cover and place it to one side.

 

 

 

 

 

 

 

Vivitek_D825EX_projector_1000055_remove_projector_lamp_screws

 

Vivitek_D825EX-projector_1000055_remove_projector_lamp

 

NOTE: The Vivitek 1000055-A (5811100760S) projector lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps! If you bought from an authentic manufacturer they will recycle the lamp for you at no extra cost.

 

Vivitek_D825EX_projector_1000055_install_new_projector_lamp

  • Take the new Vivitek 1000055-A (5811100760S) projector lamp out of its packaging. Lift up the wire handle and gently guide it into the Vivitek D825EX projector.
  • Take care not to touch the actual bulb as the oil from your fingers can leave a smudge that will burn into a black spot when the projector heats up.
  • Tighten the lamp screw.
  • Re-install the Vivitek D825EX projector lamp cover and tighten the screw.
  • Reset the total lamp hour timer.

Resetting the Vivitek D825EX Lamp Hour Timer

It’s important to only reset the lamp timer when the Vivitek 1000055-A (5811100760S) projector lamp has been replaced.

Resetting the projector lamp timer without changing the lamp can make it work beyond its recommended hours and cause harm to your Vivitek D825EX projector.

Vivitek_D825EX_projector_1000055_Reset_projector_lamp_hours

  • Press the Menu button to open the OSD menu.
  • Press left/right arrow keys to move to the Installation II menu.
  • Press up/down arrows to move to the Advanced menu
  • Press Enter.
  • Using the or up/down arrow keys to move down to the Advanced menu.
  • Press the cursor up/down arrows button to Lamp Hour Reset.
  • Press Enter.
  • A message will appear saying the Lamp Hour has been reset to zero.
  • Press the Menu button to return to the main Installation II menu.

 

Extending the life of the Vivitek 1000055-A projector lamp:

  • Keep your air filters clean to avoid overheating the projector.
  • Use the Lamp Power option on the Vivitek D825EX projector and set to Eco Mode to reduce the amount of power used but extend projector lamp life.
  • Learn more with Top tips for extending DLP projector lamp life.

 

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Vivitek_5811116206_SU_projector_lampFind the projectors compatible with the Vivitek 5811116206-SU projector lamp and learn how to install one.

The importance of authentic projector lamps

Before purchasing a Vivitek 5811116206-SU projector lamp look for the seal of approval that lets you know you are buying from an authentic manufacturer. Generics simply have too many problems that make them more expensive in the long run.

6 reasons to buy authentic projector lamps:

Protect yourself from buying counterfeit lamps.

Projectors compatible with the Vivitek 5811116206-SU projector lamp

The Vivitek 5811116206-SU projector lamp is compatible with the:

For step-by-step instructions on replacing your Vivitek 5811116206-SU projector lamp, click on your projector listed below:

 

Vivitek_H1080FD_projector_Vivitek_5811116206_projector_lamp

Click here for step-by-step instructions on how to change the Vivitek 5811116206-SU projector lamp for the Vivitek H1080 projector.

 

Vivitek_H1080FD_projector_Vivitek_5811116206_projector_lamp

 

 

Click here for step-by-step instructions on how to change the Vivitek 5811116206-SU projector lamp for the Vivitek H1080FD projector.

Vivitek_H1081_projector_Vivitek_5811116206_projector_lamp

 

Click here for step-by-step instructions on how to change the Vivitek 5811116206-SU projector lamp for the Vivitek H1081 projector.

 

 

PJVIH1082_projector_5811116206_projector_lamp

Click here for step-by-step instructions on how to change the Vivitek 5811116206-SU projector lamp for the Vivitek H1082 projector.

 

 

 

vivitek_h1085_vivitek_5811116206_projector_lamp

Click here for step-by-step instructions on how to change the Vivitek 5811116206-SU projector lamp for the Vivitek H1085 projector.

 

 

PJVIH1082_projector_5811116206_Projector_lamp

 

 

Click here for step-by-step instructions on how to change the Vivitek 5811116206-SU projector lamp for the Vivitek PJVIH1082 projector.

Extend the life of the Vivitek 5811116206-SU projector lamp:

Extend the life of the newly installed Vivitek 5811116206-SU projector lamp with the following tips:

  • Keep your air filters clean to avoid overheating the projector.
  • Turn off the Epson projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
  • Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
  • Set the Brightness Mode to low or Econo Mode to extend lamp life.
  • Learn more with Top tips for extending DLP projector lamp life.

 

Tagged with: , , , , , , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Epson_PowerLite 755c_765c_Epson_ELPLP32_projector_lamp_timerOur quick instruction guide can help you replace the Epson PowerLite 755c projector lamp in less than 15 minutes.

Be prepared with the right projector lamp

Your Epson PowerLite 755c uses the Epson ELPLP32 projector lamps. The challenging part is finding an authentic merchant you can trust for an Epson PowerLite 755c projector lamp. The Internet has been flooded with copycat manufacturers who create generic imitations. You get what you pay for and it’s usually a number of problems:

Save yourself unnecessary headaches and keep your warranty intact for your Epson PowerLite 755c projector. Look for the seal of approval and buy an authentic Epson ELPLP32 projector lamp. 7 Ways to Spot a Counterfeit Lamp.

Find this lamp on Amazon sold by these authorized dealers:

Watch for end of life signs

Epson_PowerLite 755-765C_Epson_ELPLP32_projector_lamp_ warningTrack the umber of hours left in the  Epson PowerLite 755c projector by going to the Info menu found on the Main menu. The Epson ELPLP32 projector lamp will last up to 2000 hours if the Brightness setting is on normal. Change the setting to low and get up to 3000 hours. Watch for these signs as well to let you know the end of life is coming for the Epson ELPLP32 lamp:

  • The lamp warning light on the projector starts flashing orange. If it turns red and stays red, replace the Epson ELPLP32 projector lamp immediately.
  • Imaged becomes dark, colours are off or appear to be deteriorating
  • A message saying “Replace the lamp” appears on screen.

Install the new Epson ELPLP32

Installation will take under 10 minutes but before installing the new Epson ELPLP32 projector lamp into the Epson PowerLite 755c projector, be sure to follow these preparation steps:

Epson_PowerLite 755c-765c_unplug_ELPLP32_projector_lamp

  • Turn power button off and wait for the power light to stop flashing.
  • Unplug the power cord from the Epson Powerlite 755c projector.
  • The Epson Powerlite 755c should be cool to the touch before you try to change the Epson ELPLP32 projector lamp. This projector operate at a high temperatures so you can burn yourself badly if you don’t allow for the cool down period.
  • Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Epson_PowerLite 755c_765c_remove_cover_Epson_ELPLP32_projector_lamp

  • Turn the Epson PowerLite 755c over and placing on a soft, scratch free surface.
  • Press on the tabs located on top of the Epson PowerLite 755c cover. Lift up the lamp cover.

Epson_PowerLite_remove_Epson_ELPLP32_projector_lamp

  • Using the screw driver provided with the Epson PowerLite 755c projector, loosen the two screws holding the Epson ELPLP32 projector lamp in place.

Epson_PowerLite 755-765c_remove_projector_lamp_ELPLP32Pressing on the indents on the sides of the Epson ELPLP32, pull the projector lamp gently up out of the Epson PowerLite 755c projector. Take care not to bang the actual lamp or it may break. Learn how to do a proper clean up if the lamp breaks or explodes.

NOTE: The Epson ELPLP32 projector lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps and be good to the environment.
Epson_PowerLite 755c-765c_change_air_filter_ELPLP32_projector_lamp

  • Gently place the new Epson ELPLP32 lamp into the Epson PowerLite 755c making sure not to touch the actual bulb. The oil on your fingers will leave a burn mark on the lamp once it heats up and this can cause black out spots on the screen.
  • Tighten the screws on the new Epson ELPLP32 lamp.
  • Slide the air filter out and remove it immediately. Slide in the new filter that came with the Epson ELPLP32 lamp. Replace the lamp cover.
  • You are now ready to reset the lamp timer.

 

Reset the lamp timer in the Epson PowerLite 755c

Your Epson PowerLite 755c has a built-in timer to track the life of the Epson ELPLP32 projector lamp. So, it’s very important that you reset the lamp timer every time you replace the Epson ELPLP32 projector lamp. Here’s how:

Epson_PowerLite 755c_765c_reset_projector_lamp_timer

 

  • Press the MENU button on either the remote control on the projector’s control panel.
  • Scroll down to the RESET option.
  • Press Enter. The RESET ALL screen will appear.
  • Scroll down to LAMP-HOURS RESET.
  • Press ENTER to open up the confirmation screen

 

 

Epson_PowerLite 755c_765c_reset_lamp_timer_screen2_Epson_ELPLP32_proejctor lamp

 

  • Highlight YES.
  • Press ENTER.
  • Press ESC or MENU to exit this option.

Congratulations! You’ve just installed at new Epson ELPLP32 projector lamp in your Epson PowerLite 755c.

Tips for  a longer lasting Epson ELPLP32 projector lamp:

  • Keep your air filters clean to avoid overheating the projector.
  • Turn off the Epson Powerlite 755c projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
  • Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
  • Learn more with Top tips for extending DLP projector lamp life

 

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Acer-PD120_projector_Acer_EC-J2101-001_projector_LAMPThis simple guide will teach you how to replace Acer PD120 projector lamp.

Your Acer PD120 projector uses the Acer EC.J2101.001 projector lamp. Be sure to purchase an authentic Acer PD120 projector lamp. Note: these instructions are also compatible with the following models:

  • Acer PD120D
  • Acer PD120P
  • Acer PD120PD

Be prepared with the correct projector lamp

Be sure to buy your Acer EC.J2101.001 projector lamp from an authorized dealer to keep your Acer PD120 projector working properly. Cheap knock-offs will damage the sensitive optics in your Acer PD120 projector and have a much shorter life span. Generic lamps have many problems and will make you lose money in the long run.

6 reasons to buy authentic:

Protect yourself from buying counterfeit lamps.

Find this lamp sold on Amazon by these authorized dealers:

Know the warning signs

When your Acer PD120 projector lamp is coming to its end of life, you will see this replacement message appear on screen: Lamp is approaching the end of its useful life in full power opera­tion. Replacement Suggested!”

Other warning indications may be a washed out image with faded colors. Unfortunately, when you see this warning you don’t have a lot of time to replace the projector lamp. You must replace the lamp immediately. You can track the lamp life on the Managment menu under Lamp Hour Relapse. You can expect the Acer EC.J2101.001 projector lamp to last 2000 hours on Standard mode and 3000 hours on Eco mode. You can turn Eco Mode on or off from the Management menu.

Replacing the projector lamp

Before installation safety steps:

  • Turn off the projector and unplug the AC cord.
  • These projectors operate under high temperatures and there is a risk of burning if the projector has not cooled enough. Allow the PD120 to cool for one hour. It should be cool to the touch.

Acer-PD120_remove_cover_screws_Acer_EC-J2101-001_projector_lamp

1. Use a screwdriver to remove the two screws from the cover. Acer-PD120_remove_cover_Acer_EC-J2101-001_projector_lamp

 

2 Lift the cover off the projector and place it to one side.

 

Acer-PD120_remove_lamp_screws_Acer_EC-J2101-001_projector_lamp3. Use a screwdriver to remove the two screws holding the Acer PD120 projector lamp in place. screw from the cover. Lift the wire handle on the Acer EC.J2101.001 bulb and gently pull the lamp up to remove it.

Don’t throw the old Acer EC.J2101.001 projector lamp into regular garbage as it contains mercury — send it to a local recycling program.

Acer-PD120_install_new_Acer_EC-J2101-001_projector_lamp4. Take the new Acer EC.K0700.001 projector lamp using the wire handle. Avoid touching the bare bulb; the oil on your finger can leave a black mark on the lamp affecting the projected image.

5. Tighten the screws on the new Acer EC.K0700.001 projector lamp.

6. Put the lid back onto the projector. Tighten the screw holding the lid in place. Plug the AC cables back into the projector. Turn the project on so you can reset the lamp timer.

Resetting the Lamp timer

It’s important to always reset the lamp timer after replacing the projector lamp in your Acer PD120 projector. You want the projector to track how many hours the lamp has been used and send out warning messages when the Acer EC.K0700.001 reaches end of life.

 

Acer PD120 projector_Acer_EC-J2101-001_update_projector_lamp

To reset the Projector Lamp timer:

  • Open the MAIN MENU. Press ENTER.
  • Scroll down to the MANAGEMENT menu. Press ENTER.
  • Scroll down to the Lamp Hour reset option.
  • Press the right arrow.
  • The lamp will be reset to zero.
  • You can set the Eco Mode and Lamp Hours left plus time remaining.

Learn more tips for extending lamp life.

 

Acer-PD120_Replacement_Bulb_Acer_EC-J2101-001_ projector_lamp

A green alternative

This projector has the option of also just replacing the actual bulb and re-use the plastic cage. This reduces waste and is a great way to green your projector. Watch our training video to learn more.

 

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Discount_Merchant_Boxlight_XP60M-930_projector_lampWhen it’s time to replace your Boxlight XP-60m projector lamp our handy step-by-step guide is here to help!

Get the right projector lamp

Be sure to buy an authentic Boxlight XP-60m projector lamp from a recognized dealer. The cheaper knock off lamps being sold on popular e-commerce sites may seem like a bargain but will end up costing you money. You get what you pay for and in the case of generic lamps it’s some serious problems:

Save yourself unnecessary headaches and buy an authentic Boxlight XP60M-930 from a recognized dealer. You’ll be getting a far superior product with a replacement guarantee and tech support.

Knowing when to replace the projector lamp

Boxlight_XP-60m_XP60M-930_replace_projector_lamp_warningWhen the Boxlight XP60M-930 is reaching end of life, the alarm light on the Boxlight XP-60m projector flash red. Other indications that the lamp is reaching end of life include a picture that looks dim on screen or one with faded colours. Be sure to check the lamp life using the SERVICE menu found on the SETUP MENU. NOTE: Don’t use the lamp in the projector past it’s due date or it may overheat, stop working or explode causing the projector to shut down.

 

Find this lamp sold on Amazon by these authorized dealers:

 

Replacing the Boxlight XP60M-930 projector lamp

Before replacing the Boxlight XP60M-930 follow these safety tips:

  • Disconnect the power cord on the Boxlight XP-60m projector.
  • Reduce the risk of severe burns by allowing the Boxlight XP-60m projector to cool for at least 45 minutes. These projectors operate using high temperatures and you run the risk of severe burns if you don’t allow it to cool down.

Boxlight_XP-60m_XP60M-930_projector_lamp_remove_coverStep 1: Place the projector on a soft surface and turn it over. Loosen the three screws holding the lamp unit in place.

Step 2: Carefully pull out and remove lamp housing. Be careful not to bang the bulb or it can shatter. Learn what to do if the bulb has broken.

Boxlight_XP-60m_XP60M-930_replace_projector_lampStep 3: Insert the new Boxlight XP60M-930 projector lamp. Be careful not to touch the actual bulb as this can result in black spots from the oil on your hands.

Step 4: Tighten the screw on the outside of the projector lamp module.

 

 

 

NOTE: Be sure to recycle this projector lamp properly. The Boxlight XP60M-930 lamp contains mercury and should not be thrown into regular garbage. It must be recycled properly!

Boxlight_XP-60m_XP60M-930_reset_projector_lamp_timer_ICONS Resetting the Boxlight XP-60m lamp counter

Once the Boxlight XP60M-930 has been replaced, you will need to reset the lamp counter so the Boxlight XP-60m projector can accurately track the number of lamp hours remaining.

 

To reset the lamp hours:

Boxlight_XP-60m_XP60M-930_reset_projector_lamp_timer

  • Plug in the power cord and press the Power switch to turn the projector back on.
  • Go to SETUP MENU.
  • Scroll down to the Reset lamp timer.
  • Press Enter.
  • This will reset the lamp hours to zero.
  • Verify that the counter was reset by pressing MENU/SELECT and viewing the counter in the STATUS menu.

Learn how to extend the life of the Boxlight xP-60m. Check out Top tips for extending DLP projector lamp life.

Interested in a green alternative?

Sanyo_replacement_just_bulb

The Boxlight XP-60m has the option of replacing only the actual bulb and re-using the plastic cage. This reduces waste and is a great way to green your projector. Watch our step-by-step training video to learn more.

 

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Hitachi-CP-X505_Hitachi_DT00771_projector_lampReplace the Hitachi CP-X605 projector lamp with the instruction guide.

First step: Buy authentic projector lamp

Be sure to install an authentic Hitachi CP-X605 projector lamp to keep your projector working at its best. You’ll need a Hitachi DT00771 CPX605 projector lamp.

Avoid generics. With their inferior parts, combined with a shorter life means counterfeit projector lamps cost you more in the end. Avoid exposure to the toxic materials and parts used to create the lamps and keep your warranty in place. Look for the seal of approval to make sure you are getting an authentic projector lamp.

Signs your projector lamp needs to be replaced:

  • Hitachi CP-X605 Lamp Indicator light will start flashing red.
  • Color tone on the screen may also appear weak or washed out.
  • Picture has poor colour quality.
  • You may notice the Hitachi DT00771 CPX605 starts to go dark after being used for long period of time. It does have a finite life and trying to force it to work beyond its normal life can damage your Hitachi CP-X605 projector.

Find this lamp on Amazon sold by these authorized dealers:

Hitachi-CP-X605_Hitachi_DT00771_projector_lamp_cover_screw

Replace the projector lamp

Turn the Hitachi CP-X605 projector off, and unplug the power cord. Allow the projector to cool for at least 45 minutes. It should be cool to the touch. This projector works using high heat and there is danger you can be burned.

NOTE: If the projector is mounted on the ceiling, don’t stand underneath the projector while opening the cover.

 

 

Hitachi-CP-X605_Hitachi_DT00771_projector_lamp_remove_coverLoosen the screw on the lamp cover (marked with an X). Slide the cover to off the projector and set it one side.

Hitachi-CP-X605_Hitachi_DT00771_projector_lamp_handlesLoosen the three screws holding the Hitachi DT00771 CPX605 projector lamp in place. Slowly pick up the projector lamp by its handle and pull out taking care not to bang the bulb on the side of the projector. If you do shatter the bulb, you will need take time to properly clean the projector. Learn how to clean up a broken lamp.

NOTE: The Hitachi DT00771 projector lamp contains mercury and should be properly recycled. Don’t place it into regular garbage.

Finish the installation:

  • Insert the new Hitachi DT00771 CPX605 projector lamp making sure to line it up properly and tighten the three lamp screws.
  • Slide the cover back onto the projector, lock it in place and fasten the screw.
  • Turn on the projector and set the lamp time:

To reset the lamp timer:

Hitachi CP-X605_reset_projector_lamp_timerNote: Reset the projector lamp time only when you have replaced the lamp so the Hitachi CP-X605 projector can properly track the lamp life. Otherwise you run the risk of using the lamp beyond its lamp life.

Press the MENU button

  • Scroll down to the GO TO ADVANCED MENU option. Press ENTER
  • Scroll down to the OPTION menu in the left column and press ENTER.
  • Scroll down to LAMP TIME. Press ENTER To make a dialogue field appear
  • Scroll up to the RESET option on the dialogue box.
  • The lamp setting will be set to zero.

Get more hours from your Hitachi DT00771 CPX605 by keeping your air filters clean to avoid overheating the projector. Learn more with Top tips for extending DLP projector lamp life.

Go green, save money

Hitachi_Replace_BulbIf you are looking for a green alternative, why not consider changing only the bulb and leaving the housing for the bulb. Our training video shows you how simple it is.

 

 

Tagged with: , ,

by avatarShelagh McNallyPosted on Posted in FixYourDLP, Projector Lamp Replacement Guides — No Comments ↓

Eiki_-LC-X4a_Eiki_POA-LMP39_projector lamp_modeChange your Eiki LC-X4LA projector lamp in three simple steps by following our guide.

Step 1: Buy the right lamp

Always install an authentic Eiki LC-X4LA projector lamp to keep your projector working properly. Look for the seal of approval before buying Eiki POA-LMP39 and avoid generics for the following reasons:

Go with original OEM projector lamps and save yourself hassles.

Find this lamp sold on Amazon by these authorized dealers:

Step 2: Recognize end of life warnings

NOTE: These instructions can also be used for the Eiki LC-X4A projector.

The Eiki LC-X4LA uses two Eiki POA-LMP39 projector lamps, so it’s recommended you change both at the same time. Watch for signs  indicating it’s time to change the projector lamp. There are several key functions that will help you manage end of life for the projector lamp.

Lamp Status

Eiki_LC-X4LA_Eiki_POA-LMP39_projector_lamp_mode

The Lamp Management Function detects the status of bots lamps and displays it on screen. The lamp status is also displayed for 5 seconds when the projector is turned on. The LAMP REPLACE indicator lights yellow when either lamp is nearing end of life.

Eiki LC-X4LA_Eiki_POA-LMP39_projector_lamp_remove_coverOn screen status:

  • ON: Yellow lamp on screen: Lamps are functioning normally.
  • OFF: Dim Lamp: Lamp is turned off and not in use.
  • NEAR END: Red lamp: Projection Lamp is nearing its end. When image becomes darker or color becomes unnatural, replace lamp. (The Lamp replace light on the projector lights yellow at the same time.
  • OUT: X Mark on lamp: The lamp has reached its end of life and fails to turn on. It may also be defective. Replace lamp corresponding with number marked X.

Lamp Mode Changeover: Lamp Management Function automatically changes the combination of lighting lamp (Lamp Mode) by detecting the status of each projector lamp. When any of the two lamps goes out, Lamp Mode is changed over from 2 lamps to 1 lamp. Lamp Mode can be switched to 2 lamps or 1 lamp manually. Check the number of lamps being used on the Lamp Status.

Step 3: How to replace the Eiki POA-LMP39 lamp

Follow these important safety steps before replacing the Eiki POA-LMP39 lamp.

  • The Eiki LC-X4LA projector operates under very high temperatures. Let it cool for one full hour before attempting to replace the lamp in order to avoid being burned.
  • Turn off the projector by pressing the power button. Wait for the light to stop flashing.
  • Turn off the power switch at the back on the projector
  • Unplug any power cords.

NOTE: To maintain quality of picture (better balance of color and brightness in entire screen), replacing both lamps at the same time.

Eiki_LC-X4LA_Eiki_POA-LMP39_remove_projector_lamp

  • Loosen the three screws on Lamp Cover and remove Lamp Cover.

 

Eiki_LC-X4LA_Eiki_POA-LMP39_replace_projector_lamp

  • Loosen the 2 screws. Using the wire handle and pull out the projector lamp. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.
  • Replace the Lamp Assembly. NOTE: The Eiki POA-LMP39 contains mercury and should be properly recycled. Don’t place it into regular garbage.
  • Make sure that Lamp Assembly is set properly. Tighten the 2 screws on the new lamp
  • Replace Lamp Cover and tighten 3 screws. Connect AC Power Cord to a projector and turn projector on.
  • Reset Lamp Replacement Counter.

Reset Eiki LC-X4LA lamp counter

Your Eiki LC-X4LA projector has a built in lamp counter to determine when the projector lamp should be replaced. It needs to be reset every time you replace the Eiki POA-LMP39 projector lamps. When the Lamp Replace Counter is reset, the LAMP REPLACE indicator stops lighting.

Eiki_LC-X4LA_Eiki_POA-LMP39_reset_projector_lamp_timer

  • Turn projector on, press MENU button and ON-SCREEN MENU will appear.
  • Press POINT LEFT/RIGHT button(s) to move the red frame pointer to SETTING Menu icon. Press POINT DOWN button to move a red frame pointer to “Lamp counter reset.”
  • Press SELECT button.
  • Move arrow to select either Lamp 1 or Lamp 2. Press SELECT button.

Eiki_LC-X4LA_Eiki_POA-LMP39_reset_projector_lamp_timer_2

  • Message “Lamp replace counter Reset?” is displayed.
  • Move pointer to YES and then press SELECT button.
  • NOTE: Be sure to reset correct lamp number otherwise LAMP REPLACE indicator continues lighting.
  • Another confirmation dialog box appears and select YES to reset Lamp Replace Counter.
  • Do not reset Lamp Replace Counter except after Projection lamp is replaced.

Extend the life of the Eiki POA-LMP39 projector lamp

Get more hours from your Eiki POA-LMP39 lamp by following these maintenance tips:

  • Keep your air filters clean to avoid overheating the projector.
  • Turn off the Eiki LC-X4LA projector and let it stand unused for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
  • Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
  • Learn more with Top tips for extending DLP projector lamp life.
  • Press the MENU button to exit.

Save money, go green

Video_Changing_Lamp_for_Eiki_LC-X4LA_projector_lampLooking for a green alternative? Try replacing only the bulb and re-using the same projector lamp cage for the Eiki LC-X4LA projector. You save money and reduce waste.

Watch our how to video guide to learn more.

 

Tagged with: , ,
Join the discussion on Facebook! All your questions, answered! The Screen & Projector Group