Buying the right lamp

Purchase your lamp ahead of time and be prepared.  The Optoma ES526L projector uses the Optoma BL-FU185A projector lamp Be sure to purchase an authentic, OES Optoma ES526L projector lamp. Avoid counterfeit lamp for the following reaons;

• shorter lamp life than original lamps
• created with toxic materials and carcinogenic parts including Krypton-85
• prone to explosions
• can damage the sensitive electronics in your projectors
• when you buy copy-cat lamps you get no guarantee or refunds
• installing a generic lamp voids your projector’s warranty.

Spot the counterfeit.

Find this lamp sold on Amazon by these authorized dealers:

• Optoma BL-FU185A, UHP, 185W Projector Lamp Optoma BL-FU185A Projector lamp – UHP – 185 Watt – for Optoma DS316, ES526, EW536, EX536, Pro350, TS526, TW536, TX536, Home Theater Series HD66
• BL-FU185A Optoma Projector Lamp Replacement. Projector Lamp Assembly with Genuine Original Philips UHP Bulb Inside.
• Optoma BL-FU185A Replacement Lamp for TS526/PRO150S/DS316/TX536/PRO250X/DX619 Projectors
• Optoma 00185 – BL-FU185A Projector Light Bulb
  

When to replace the projector lamp

Your Optoma ES526L projector uses the Optoma BL-FU185A  projector lamp . When the projector lamp is approaching end of life, you may notice the Lamp-LED light flashing red or the picture quality starting to get poor resolution with washed out colours. As the projector lamp approaches end of life, the projector lamp replacement message flashes on screen. Change your projector lamp immediately. The projector will not work if the lamp has burnt out or broken.

If you hear a loud pop when turning on the projector, the Optoma BL-FU185A  projector lamp has broken. Learn what to do if the lamp has exploded inside the projector.

Installing the Optoma BL-FU185A projector lamp

Before replacing the Optoma BL-FU185A projector lamp follow these important safety tips:

• Switch off the power to the Optoma ES526L projector by pressing the Power/Standby button.
• Disconnect the power cord.
• Allow the projector to cool down for at least 30 minutes. If should be cool to the touch. These projectors run using high temperatures and you can burn yourself badly if you don’t allow the projector to cool down.

1. Use a screwdriver to undo the two screws holding the lamp cover in place. The screws on the lamp cover and the lamp cannot be removed.

2. Remove the lid and place to one side. Don’t lose the lid as the Optoma ES526L projector will not turn back on until the lamp cover has been properly installed.

3. Remove the two screws holding the Optoma BL-FU185A  in place.

Note: The used Optoma BL-FU185A projector lamp contains mercury and should be properly recycled. Don’t throw it into regular garbage.

4. Lift up the wire handle on the Optoma BL-FU185A projector lamp and slowly remove it from the projector.

Be careful not to bang the projector lamp against the projector as this may case the bulb to break. Learn how to clean up a broken projector lamp.

5. Remove the new Optoma BL-FU185A projector lamps from its packaging. Without touching the actual bulb, lift up the handle on the new lamp and gently insert.

6. Tighten the two screws on the lamp.

7. Replace the lamp cover and tighten its two screws. You are now ready to reset the Lamp Replacement Timer.

Reset the Lamp Replacement Timer

The Optoma ES526L projector has an automatic lamp timer that tracks the numbers of hours left in the lamp. If you don’t reset the lamp replacement timer you run the risk of the lamp being used beyond its recommended life and possibly exploding in the projector.

To reset the Lamp Replacement Timer:

• Turn on the projector.
• Using the remote press MENU
• Select OPTIONS
• Select LAMP SETTINGS
• Select LAMP RESET
• Select YES.
• Press MENU to exit.

Tips for extending Optoma BL-FU185A lamp life:

• Chose the “STD” mode to to dim the projector lamp and lower power consumption. This will extend the lamp life by up to 130%.
• Keep your air filters clean to avoid overheating the projector.
• Every 24 hours, turn off the projector and let it stand for 1 hour
• Make sure there is enough airflow around the Optoma ES526L projector particularly if it’s been permanently mounted.
• Learn more with Top tips for extending DLP projector lamp life.

  Green your Optoma ES526L projector

  The Optoma ES526L projector has the option of re-using the existing lamp cage and replacing only the actual bulb. A great way to reduce and recycle. Watch our Optoma BL-FU185A training video to learn more.

The post Switch to a new Optoma ES526L projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Step 1: Be ready with the right type of projector lamp

You will want to be prepared and have your Optoma DS216 projector lamp purchased ahead of time. Otherwise, you may be caught off guard with a broken projector lamp and projector that isn’t working. Be sure to purchase an authentic, OES lamp for your Optoma DS216 projector.

Why avoid generics:

• shorter lamp life than original lamps
• created with toxic materials and carcinogenic parts including Krypton-85
• prone to explosions
• can damage the sensitive electronics in your projectors
• when you buy copy-cat lamps you get no guarantee or refunds
• installing a generic lamp voids your projector’s warranty.

They are simply not worth the hassles for the few dollars you save. Protect your projector and invest in authentic projector lamps. Learn How to spot a counterfeit.

Find this lamp sold on Amazon by these authorized dealers:

• Optoma BL-FU185A, UHP, 185W Projector Lamp Optoma BL-FU185A Projector lamp – UHP – 185 Watt – for Optoma DS316, ES526, EW536, EX536, Pro350, TS526, TW536, TX536, Home Theater Series HD66
• BL-FU185A Optoma Projector Lamp Replacement. Projector Lamp Assembly with Genuine Original Philips UHP Bulb Inside.
• Optoma BL-FU185A Replacement Lamp for TS526/PRO150S/DS316/TX536/PRO250X/DX619 Projectors
• Optoma 00185 – BL-FU185A Projector Light Bulb
  

Step 2: When to replace the projector lamp?

Your Optoma DS216 projector uses the Optoma BL-FU185A projector  lamp. When the projector lamp is approaching end of life, you will see the Lamp-LED light flashing red and the lamp warning message will start flashing on screen. Other indications include faded colors and poor resolution. Don’t wait to change the lamp when you get these warnings. If you do try to extend the hours beyond the recommended hours, the lamp may explode inside the projector. Learn what to do if the projector lamp has exploded inside the projector.

Step 3: Installing the Optoma BL-FU185A projector lamp

Before replacing the Optoma BL-FU185A  projector lamp follow these important safety tips:

• Switch off the power to the Optoma DS216 projector by pressing the Power/Standby button.
• Disconnect the power cord.
• Allow the projector to cool down for at least 30 minutes. If should be cool to the touch. These projectors run using high temperatures and you can burn yourself badly if you don’t allow the projector to cool down.

1. Use a screwdriver to undo the two screws holding the projector lamp cover in place. The screws on the projector lamp cover and the lamp cannot be removed.

2. Remove the lid and place to one side. Don’t lose the lid as the Optoma DS216 projector will not turn back on until the lamp cover has been properly installed.

3. Remove the two screws holding the Optoma BL-FU185A  projector lamp in place. Note: The used Optoma BL-FU185A  projector lamp contains mercury and should be properly recycled. Don’t throw it into regular garbage

4. Lift up the wire handle on the Optoma BL-FU185A projector lamp and slowly remove it from the projector.

Be careful not to bang the projector lamp against the projector as this may case the bulb to break. Learn how to clean up a broken projector lamp.

5. Remove the new Optoma BL-FU185A  projector lamp from its packaging. Taking care not to touch the actual bulb, lift up the handle on the new lamp and insert it gently into the Optoma DS216 projector.

6. Tighten the two screws on the projector lamp.

7. Replace the projector lamp cover and tighten its two screws. You are now ready to reset the Lamp Replacement Timer.

Reset the Projector Lamp Replacement Timer

The Optoma DS216 projector has an automatic lamp timer that tracks the numbers of hours left in the projector lamp. If you don’t reset the projector lamp replacement timer you run the risk of the lamp being used beyond its recommended life and possibly exploding in the projector.

To reset the Lamp Replacement Timer:

• Turn on the projector.
• Using the remote press MENU
• Select OPTIONS
• Select LAMP SETTINGS
• Select LAMP RESET
• Select YES.
• Press MENU to exit.

Tips for extending Optoma BL-FU185A  projector lamp life:

• Chose the “STD” mode to to dim the projector lamp and lower power consumption. This will extend the lamp life by up to 130%.
• Keep your air filters clean to avoid overheating the projector.
• Every 24 hours, turn off the projector and let it stand for 1 hour
• Make sure there is enough airflow around the Optoma DS216 projector particularly if it’s been permanently mounted.
• Learn more with Top tips for extending DLP projector lamp life.

The post 4 Steps to replacing the Optoma DS216 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

It’s easy to replace the Optoma DS316L projector lamp.

 Step 1: When to replace the Optoma DS316L projector lamp

Your Optoma DS316L projector uses the Optoma BL-FU185A  projector lamp . When the Optoma DS316L projector lamp is approaching end of life, you may  notice the Lamp-LED light flashing red or the picture quality starting to get poor resolution with washed out colours. As the projector lamp approaches end of life, the  projector lamp replacement message flashes on screen. Change your proejctor lamp immediately.  The projector will not work if the lamp has burnt out or broken.

If you hear a loud pop when turning on the projector, the Optoma BL-FU185Aprojector lamp has broken. Learn what to do if the lamp has exploded inside the projector.

Step 2: Buying the right Optoma DS316L projector lamp

You will want to be prepared and have your Optoma BL-FU185A  projector lamp purchased ahead of time. Otherwise, you may be caught off guard with a broken lamp and projector that isn’t working. Be sure to purchase an authentic, OES projector lamp for your Optoma DS316L projector. You’ll notice an overwhelming selection but unfortunately many of the lamps being sold are counterfeit with long list of associated problems:

• shorter lamp life than original lamps
• created with toxic materials and carcinogenic parts including Krypton-85
• prone to explosions
• can damage the sensitive electronics in your projectors
• when you buy copy-cat lamps you get no guarantee or refunds
• installing a generic lamp voids your projector’s warranty.

Learn How to spot a counterfeit.

Find this lamp sold on Amazon by these authorized dealers:

• Optoma BL-FU185A, UHP, 185W Projector Lamp Optoma BL-FU185A Projector lamp – UHP – 185 Watt – for Optoma DS316, ES526, EW536, EX536, Pro350, TS526, TW536, TX536, Home Theater Series HD66
• BL-FU185A Optoma Projector Lamp Replacement. Projector Lamp Assembly with Genuine Original Philips UHP Bulb Inside.
• Optoma BL-FU185A Replacement Lamp for TS526/PRO150S/DS316/TX536/PRO250X/DX619 Projectors
• Optoma 00185 – BL-FU185A Projector Light Bulb
  

Step 3: Installing the Optoma BL-FU185A projector lamp

Before replacing the Optoma BL-FU185A projector lamp follow these important safety tips:

• Switch off the power to the Optoma DS316L projector by pressing the Power/Standby button.
• Disconnect the power cord.
• Allow the projector to cool down for at least 30 minutes. If should be cool to the touch. These projectors run using high temperatures and you can burn yourself badly if you don’t allow the projector to cool down.

1. Use a screwdriver to undo the two screws holding the lamp cover in place. The screws on the lamp cover and the lamp cannot be removed.

2. Remove the lid and place to one side. Don’t lose the lid as the Optoma DS316L projector will not turn back on until the lamp cover has been properly installed.

3. Remove the two screws holding the Optoma BL-FU185A in place.

Note: The used Optoma BL-FU185A projector lamp contains mercury and should be properly recycled. Don’t throw it into regular garbage.

4. Lift up the wire handle on the Optoma BL-FU185A projector lamp and slowly remove it from the projector.

Be careful not to bang the projector lamp against the projector as this may case the bulb to break. Learn how to clean up a broken projector lamp.

5. Remove the new Optoma BL-FU185A  projector lamps from its packaging. Taking care not to touch the actual bulb, lift up the handle on the new lamp and insert it gently into the Optoma DS316L projector.

6. Tighten the two screws on the lamp.

7. Replace the lamp cover and tighten its two screws. You are now ready to reset the Lamp Replacement Timer.

Reset the Lamp Replacement Timer

The Optoma DS316L projector has an automatic lamp timer that tracks the numbers of hours left in the lamp. If you don’t reset the lamp replacement timer you run the risk of the lamp being used beyond its recommended life and possibly exploding in the projector.

To reset the Lamp Replacement Timer:

• Turn on the projector.
• Using the remote press MENU
• Select OPTIONS
• Select LAMP SETTINGS
• Select LAMP RESET
• Select YES.
• Press MENU to exit.

Tips for extending Optoma BL-FU185A lamp life:

• Chose the “STD” mode to to dim the projector lamp and lower power consumption. This will extend the lamp life by up to 130%.
• Keep your air filters clean to avoid overheating the projector.
• Every 24 hours, turn off the projector and let it stand for 1 hour
• Make sure there is enough airflow around the Optoma DS316L projector particularly if it’s been permanently mounted.
• Learn more with Top tips for extending DLP projector lamp life.

The post Install a new Optoma DS316L projector lamp in 3 easy steps appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Instead, follow this easy how-to guide and install a new lamp quickly and easily. When it’s time to replace the Optoma TW536 projector lamp may also notice the Lamp-LED light flashing red or the picture quality starting to get poor resolution with washed out colours.

You will also see the lamp warning message flash on screen. This means you have no more than 30 hours before the bulb will burn out. Change the Optoma BL-FU185A lamp in your Optoma TW536 immediately.

Authentic lamps are critical!

You’ll want the best lamp for your Optoma TW536 and that means buying directly from an authorized manufacturer. Look for the seal of approval that lets you know you are buying an authentic projector lamp.  Why avoid generics? While their price tag may seem appealing, you get what you pay for and with compatible, generic lamps that means a whole lot of headaches:

• shorter lamp life than original lamps
• created with toxic materials and carcinogenic parts including Krypton-85
• prone to explosions
• can damage the sensitive electronics in your projectors
• when you buy copy-cat lamps you get no guarantee or refunds
• installing a generic lamp voids your projector’s warranty.

Learn How to buy an authentic lamp.

Find this lamp sold on Amazon by these authorized dealers:

• Optoma BL-FU185A, UHP, 185W Projector Lamp Optoma BL-FU185A Projector lamp – UHP – 185 Watt – for Optoma DS316, ES526, EW536, EX536, Pro350, TS526, TW536, TX536, Home Theater Series HD66
• BL-FU185A Optoma Projector Lamp Replacement. Projector Lamp Assembly with Genuine Original Philips UHP Bulb Inside.
• Optoma BL-FU185A Replacement Lamp for TS526/PRO150S/DS316/TX536/PRO250X/DX619 Projectors
• Optoma 00185 – BL-FU185A Projector Light Bulb
  

Installing the Optoma BL-FU185A

Before replacing the Optoma BL-FU185A follow these crucial safety tips to prevent injury to yourself or the projector:

• Switch off the power to the Optoma TW536 projector by pressing the Power/Standby button.
• Disconnect the power cord.
• Allow the projector to cool down for at least 30 minutes. If should be cool to the touch. These projectors run using high temperatures and you can burn yourself badly if you don’t allow the projector to cool down.

1. Use a screwdriver to undo the two screws holding the lamp cover in place. The screws on the lamp cover and the lamp cannot be removed.

2. Remove the lid and place to one side. Don’t lose the lid as the Optoma TW536 projector will not turn back on until the lamp cover has been properly installed.

3. Remove the two screws holding the Optoma BL-FU185A in place.

Note: The used Optoma BL-FU185A lamp contains mercury and should be properly recycled. Don’t throw it into regular garbage.

4. Lift up the wire handle on the Optoma BL-FU185A lamp and slowly remove it from the projector. Be careful not to bang the lamp against the projector as this may case the bulb to break. Learn what to do if the lamp has exploded inside the projector.

5. Remove the new Optoma BL-FU185A from its packaging. Taking care not to touch the actual bulb, lift up the handle on the new lamp and insert it gently into the Optoma TW536 projector.

6. Tighten the two screws on the lamp.

7. Replace the lamp cover and tighten its two screws. Reset the lamp timer.

Reset the Lamp Replacement Timer

The Optoma DS316 projector has an automatic lamp timer that tracks the numbers of hours left in the lamp. When the Optoma BL-FU185A  is approaching end of life, the lamp replacement timer will trigger the warning system. If you don’t reset the lamp replacement timer you run the risk of the lamp being used beyond its recommended life and possibly exploding in the projector.

Should the lamp explode, learn what to do.

To reset the Lamp Replacement Timer:

• Turn on the projector.
• Using the remote press MENU
• Select OPTIONS
• Select LAMP SETTINGS
• Select LAMP RESET
• Select YES.
• Press MENU to exit.

Extend the life of the Optoma BL-FU185A lamp:

• Chose the “STD” mode to to dim the projector lamp and lower power consumption. This will extend the lamp life by up to 130%.
• Keep your air filters clean to avoid overheating the projector.
• Every 24 hours, turn off the projector and let it stand for 1 hour
• Make sure there is enough airflow around the Optoma TW536 projector particularly if it’s been permanently mounted.
• Learn more with Top tips for extending DLP projector lamp life

The post Optoma TW536 projector lamp installation guide appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.