Sanyo POA-LMP 21, Sanyo POA-LMP21 (service parts no 610 290 6939)

The life of the Sanyo POA-LMP21j (service parts no 610 290 6939) lamp runs anywhere from 1,000 to 3,000 hours. It’s life cycle will vary  depending on how often  depending your projector is use and whether there is regular maintenance of the filters.

The life expectancy of your Sanyo POA-LMP21j (service parts no 610 290 6939)lamp depends on the amount of usage and whether the air filters are cleaned on a regular basis. A build up of dust on the filters will reduce the cooling fans effectiveness and may cause the lamp to overheat. It’s always a good idea to keep a spare lamp on hand so you can replace the lamp immediately and not wait to use the projector.

Only genuine Sanyo POA-LMP21j (service parts no 610 290 6939) lamps should be used when replacing the projector lamp order to keep your projector is good working order. The authentic POA-LMP21j has been manufactured to meet the specifications of the Sanyo projectors.

While knock-off lamps may seem like a bargain due to their low prices, these counterfeit lamps  can damage the sensitive and expensive mechanisms and expensive mechanisms in your Sanyo  projector and may also void your guarantee from the manufacturer. Purchasing a genuine  Sanyo POA-LMP21j (610 290 6939) will ensure you keep your projector in good working order.

The Sanyo POA-LMP 21 can be used in the following projectors:

Sanyo PLC-SU20
Sanyo PLC-SU22
Sanyo PLC-XU20
Sanyo PLC-XU22

For step-by-step instructions on how to replace the Sanyo POA-LMP21j (service parts no 610 290 6939) projector lamp, please click on your specific model listed below:

Sanyo PLC SU20N Projectior

Click here for step-by-step instructions on how to change the Sanyo POA-LMP21j (service parts no 610 290 6939) projector lamp for the Sanyo PLC-SU20 projector.

Sanyo PLC SU22 Projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP21j (service parts no 610 290 6939) projector lamp for the Sanyo PLC-SU22 projector.

Sanyo PLC-XU20

Click here for step-by-step instructions on how to change the Sanyo POA-LMP21j (service parts no 610 290 6939) projector lamp for the Sanyo PLC-XU20 projector.

Sanyo PLC XU22-N projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP21j (service parts no 610 290 6939) projector lamp for the Sanyo PLC-XU22 projector.

The post When to replace your Sanyo POA-LMP 21 appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Sanyo PLC XU22-N projector

When your Sanyo POA-LMP21j (service parts no 610 290 6939) projector lamp is nearing its end of life you’ll see the  Lamp Replace Indicator on the Sanyo PLC-XU22 projector flash red. You will need to replace the lamp immediately.  Follow our step-by-step instructions to install the new Sanyo POA-LMP21j (610 290 6939) projector lamp.

Before installation

Buy your  Sanyo POA-LMP21j (service parts no 610 290 6939) from an authorized manufacturer and avoid the lower-prices knock-off lamps. These counterfeit lamps are usually made with counterfeit parts that can damage sensitive mechanisms in your Sanyo PLC-XU22. This can end up costing you more money in the long run.  Buying from a legitimate source keeps your projector under warranty and gives you a solid guarantee.

Instructions for replacing the Sanyo PLC-XU22 Projector Lamp

1. Before installing the new Sanyo POA-LMP21j (service parts no 610 290 6939) lamp turn off the projector and unplug the AC cord. Allow the Sanyo PLC-XU22 projector to cool to the touch. This can take between 45 to 60 minutes. Don’t open the projector when its still hot since these machines operate under high temperatures and you can burn yourself.

2. The lamp cover for the Sanyo PLC-XU22 is located at the bottom of the projector. Gently turn over the projector onto its side and loosen the screw holding the cover in place. Place the cover to one side.

3. Loosen both screws holding the Sanyo POA-LMP21j (6102906939) lamp cage in place. Grab the lamp handle and gently lift the lamp out of its socket. Place to one side. Be sure to dispose of the lamp properly through a local recycling program.

4. Take the new Sanyo POA-LMP21j (service parts no 610 290 6939) lamp cage by the handle—avoid touching the actual bulb a this can break or damage the lamp. Without forcing the lamp, place it into the slot.

5. Once the lamp is in, tighten both screws on the Sanyo POA-LMP21j (610 290 6939) Lamp Assembly. Make sure the screws have been tightened properly or the Sanyo PLC-XU22 projector will not turn on.

6. Replace the Lamp Cover and tighten the screw. Re-connect the power cord and turn on the Sanyo PLC-XU22 projector. If the Sanyo POA-LMP21j (610 290 6939) lamp does not turn on after the warm-up period, try re-installing the lamp. Reset the Lamp Counter Screen by following the instructions below.

NOTE: Be sure to properly recycle your used Sanyo POA-LMP21j (service parts no 610 290 6939) lamps. Since they contain mercury they can’t be placed into regular garbage.

How to reset the Sanyo PLC-XU22 Lamp Replacement Monitor Timer

In order for the projector to properly track the lamp life of your Sanyo POA-LMP21j (service parts no 610 290 6939) you’ll need to reset the Lamp Replacement Monitor Timer. Failure to do so can result in the Replace Lamp Indicator not tracking the lamp life properly.

• Turn the Sanyo PLC-XU22 projector on.
• Press the MENU button to access the ON-SCREEN MENU.
• Press the POINT LEFT/RIGHT button to select the SETTING menu.
• Press the SELECT button to open the SETTING MENU option.
• Press the POINT DOWN button so the red-arrow appears.
• Move down to the LAMP AGE option. Press SELECT to open the next option.
• The message “Lamp replace monitor Reset?” will be displayed.
• Click on the option YES to reset the timer.
• RESET the Lamp Replacement Monitor Timer ONLY WHEN the lamp has been REPLACED.

Extend the life of the SANYO POA-LMP 21 lamp

Extend the life of your newly installed Sanyo POA-LMP21j (service parts no 610 290 6939) by following these tips:

• Wait at least five minutes before turning the Sanyo PLC-XU22 projector off.
• Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
• Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP21j (service parts no 610 290 6939) and prevent the Sanyo PLC-XU22 from overheating.

The post 6 Steps to replacing the Sanyo PLC-XU22 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Sanyo PLC-XU20 Projector

Watch for the yellow blinking light on your Sanyo PLC-XU20’s Lamp Replacement Indicator. The blinking light indicates your Sanyo POA-LMP21 (service parts no 610 290 6939) lamp is reaching its end of life. Follow our easy step-by-step instructions to replace your projector lamp

Instructions for replacing the Sanyo PLC-XU20 Projector Lamp

It’s important to buy only a genuine POA-LMP21 to replace the old lamp. The price of generic knock-off lamps may be tempting but can cost you more money in the long run. Counterfeit lamps are not manufactured according to Sanyo’s specifications and can damage the sensitive (and expensive) mechanisms in your Sanyo PLC-XU20 projector.

Before installation

Before installing the new Sanyo POA-LMP21 (610 290 6939) lamp be sure to turn off the projector and unplug the AC cord. Allow the Sanyo PLC-XU20 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures.

Step-by-step instructions for replacing the Sanyo POA-LMP 21 Lamp Assembly

• The lamp cover for the Sanyo PLC-XU20 is located at the bottom of the projector. Gently turn over the projector onto its side and loosen the screw holding the cover in place. Place the cover to one side.
• Loosen both screws holding the Sanyo POA-LMP21 (service parts no 610 290 6939) lamp cage in place. Grab the lamp handle and gently lift the lamp out of its socket. Place to one side.
• Be sure to dispose of the lamp properly through a local recycling program.
• Take the new Sanyo POA-LMP21 (610 290 6939) lamp cage by the handle—avoid touching the actual bulb a this can break or damage the lamp. Without forcing the lamp, place it into the slot.
• Once the lamp is in, tighten both screws on the Sanyo POA-LMP21 (6102906939) Lamp Assembly. Make sure the screws have been tightened properly or the Sanyo PLC-XU20 projector will not turn on.
• Replace the Lamp Cover and tighten the screw. Re-connect the power cord and turn on the Sanyo PLC-XU20 projector If the Sanyo POA-LMP21 (service parts no 610 290 6939) lamp does not turn on after the warm-up period, try re-installing the lamp.
• Reset the Lamp Counter Screen by following the instructions below.

NOTE: BE sure to properly recycle your used Sanyo POA-LMP21 (610 290 6939) lamps. Since they contain mercury they can’t be placed into regular garbage.

How to reset the Sanyo PLC-XU20 Lamp Replacement Monitor Timer

In order for the projector to properly track the lamp life of your Sanyo POA-LMP21 (service parts no 610 290 6939) you’ll need to reset the Lamp Replacement Monitor Timer. Failure to do so can result in the Replace Lamp Indicator not tracking the lamp life properly.

• Turn the Sanyo PLC-XU20 projector on.
• Press the MENU button to access the ON-SCREEN MENU.
• Press the POINT LEFT/RIGHT button to select the SETTING menu.
• Press the SELECT button to open the SETTING MENU option.
• Press the POINT DOWN button so the red-arrow appears.
• Move down to the LAMP AGE option. Press SELECT to open the next option.
• The message “Lamp replace monitor Reset?” will be displayed.
• Click on the option YES to reset the timer.
• RESET the Lamp Replacement Monitor Timer ONLY WHEN the Sanyo POA-LMP21 (610 290 6939) lamp has been REPLACED.

Extend the life of the SANYO POA-LMP 21 lamp

Extend the life of your newly installed Sanyo POA-LMP21 (service parts no 610 290 6939) by following these tips:

• Wait at least five minutes before turning the Sanyo PLC-XU20 projector off.
• Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
• Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP21 (service parts no 610 290 6939) and prevent the Sanyo PLC-XU20 from overheating.

The post How to replace the Sanyo PLC-XU20 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Sanyo PLC SU22 Projector

STEP-BY-STEP INSTRUCTIONS FOR SANYO PLC-SU22 LAMP REPLACEMENT

When it’s time to change your lamp on your Sanyo PLC-SU22 projector, you’ll notice the yellow light blinking on the Lamp Indicator found on the top control panel.

You’ll need a Sanyo POA-LMP21 (service parts no 610 290 6939) lamp as a replacement.

BEFORE INSTALLATION

Be sure to buy an authentic Sanyo POA-LMP21 (service parts no 610 290 6939) lamp bought from a verified source. These genuine lamps have manufactured to meet the specifications of the PLC-XE40/PLC-XE45 projector.  Resist the temptation to buy a cheaper POALMP21 as these generic lamps often use counterfeit parts that can damage the sensitive mechanisms in your Sanyo PLC-SU22 projector.

REPLACING THE SANYO POA-LMP 21 LAMP

• The lamp cover for the Sanyo PLC-SU22 is located at the bottom of the projector. Gently turn over the projector onto its side and loosen the screw holding the cover in place. Place the cover to one side.
• Loosen both screws holding the Sanyo POA-LMP21 (610 290 6939) lamp cage in place. Grab the lamp handle and gently lift the lamp out of its socket. Place to one side. Be sure to dispose of the lamp properly through a local recycling program.
• Take the new Sanyo POA-LMP21 (6102906939) lamp cage by the handle—avoid touching the actual bulb as this can break or damage the lamp. Without forcing the lamp, place it into the slot.
• Once the lamp is in, tighten both screws on the Sanyo POA-LMP21 (service parts no 610 290 6939) Lamp Assembly. Make sure the screws have been tightened properly or the Sanyo PLC-SU22 projector will not turn on.
• Replace the Lamp Cover and tighten the screw. Re-connect the power cord and turn on the Sanyo PLC-SU22 projector. If the Sanyo POA-LMP21 (610 290 6939) lamp does not turn on after the warm-up period, try re-installing the lamp.
• Reset the Lamp Counter Screen by following the instructions below.

NOTE: BE sure to properly recycle your used Sanyo POA-LMP21 (service parts no 610 290 6939) lamps. Since they contain mercury they can’t be placed into regular garbage.

RESETTING THE LAMP REPLACEMENT MONITOR TIMER

In order for the projector to properly track the lamp life of your Sanyo POA-LMP21 (service parts no 610 290 6939) you’ll need to reset the Lamp Replacement Monitor Timer. Failure to do so can result in the Replace Lamp Indicator not tracking the lamp life properly.

• Turn the projector on.
• Press the MENU button to access the ON-SCREEN MENU.
• Press the POINT LEFT/RIGHT button to select the SETTING menu.
• Press the SELECT button to open the SETTING MENU option.
• Press the POINT DOWN button so the red-arrow appears.
• Move down to the LAMP AGE option. Press SELECT to open the next option.
• The message “Lamp replace monitor Reset?” will be displayed.
• Click on the option YES to reset the timer.
• RESET the Lamp Replacement Monitor Timer ONLY WHEN the lamp has been REPLACED.

MAKE THE SANYO POA-LMP 21 LAMP LAST LONGER

Extend the life of your newly installed Sanyo POA-LMP21 (service parts no 610 290 6939) by following these tips:

• Wait at least five minutes before turning the Sanyo PLC-SU22 projector off.
• Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
• Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP21 (service parts no 610 290 6939) and prevent the Sanyo PLC-SU22 from overheating.

The post Change your Sanyo PLC-SU22 projector lamp in 6 easy steps appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Sanyo PLC SU20N Projectior

STEP-BY-STEP INSTRUCTIONS FOR SANYO PLC-SU20 LAMP REPLACEMENT

The life span for the projector lamp in a Sanyo PLC-SU20 projector depends on how much the projector is used and how often the air filter is cleaned. With proper care and maintenance, you can expect between  two to three thousand hours of use.

When you are approaching end of life with your lamp, the Lamp Replacement Indicator will blink yellow. When this happens replace the lamp with a genuine Sanyo POA-LMP21 (service parts no 610 290 6939).

Be sure to purchase an authentic lamp to ensure you are getting a Sanyo POA-LMP21 (610 290 6939) that has been made to fit properly into the Sanyo PLC-SU20 projector. Installing a generic lamp can damage your projector and may cost you more in the long run.

Before Installing

Allow the Sanyo PLC-SU20 projector to thoroughly cool before changing the lamp. Turn off the projector, unplug the AC cord and allow 45 to 60 minutes for the projector to cool. These projectors operate under high heat and there is a possibility of being burned, if the projector is not fully cooled before changing the Sanyo POA-LMP21 (service parts no 610 290 6939) lamp.

Replacing the Sanyo POA-LMP 21 Lamp Assembly

• The lamp cover for the Sanyo PLC-SU20 is located at the bottom of the projector. Gently turn over the projector onto its side and loosen the screw holding the cover in place. Place the cover to one side.
• Loosen both screws holding the Sanyo POA-LMP21 (service parts no 610 290 6939) lamp cage in place. Grab the lamp handle and gently lift the lamp out of its socket. Place to one side.
• Be sure to dispose of the lamp properly through a local recycling program.
• Take the new Sanyo POA-LMP21 (service parts no 610 290 6939) lamp cage by the handle—avoid touching the actual bulb as this can break or damage the lamp. Without forcing the lamp, place it into the slot.
• Once the lamp is in, tighten both screws on the Sanyo POA-LMP21 (610 290 6939) Lamp Assembly. Make sure the screws have been tightened properly or the Sanyo PLC-SU20 projector will not turn on.
• Replace the Lamp Cover and tighten the screw. Re-connect the power cord and turn on the Sanyo PLC-SU20 projector If the Sanyo POA-LMP21 (6102906939) lamp does not turn on after the warm-up period, try re-installing the lamp. Reset the Lamp Replacement Monitor by following the instructions below.

NOTE: BE sure to properly recycle your used Sanyo POA-LMP21 (service parts no 610 290 6939) lamps. Since they contain mercury they can’t be placed into regular garbage.

RESETTING THE LAMP REPLACEMENT MONITOR TIMER FOR SANYO PLC-SU20 PROJECTOR

In order for the projector to properly track the lamp life of your Sanyo POA-LMP21 (service parts no 610 290 6939) you’ll need to reset the Lamp Replacement Monitor Timer. Failure to do so can result in the Replace Lamp Indicator not tracking the lamp life properly.

• Turn the Sanyo PLC-SU20 projector on.
• Press the MENU button to access the ON-SCREEN MENU.
• Press the POINT LEFT/RIGHT button to select the SETTING menu.
• Press the SELECT button to open the SETTING MENU option.
• Press the POINT DOWN button so the red-arrow appears.
• Move down to the LAMP AGE option. Press SELECT to open the next option.
• The message “Lamp replace monitor Reset?” will be displayed.
• Click on the option YES to reset the timer.
• RESET the Lamp Replacement Monitor Timer ONLY WHEN the lamp has been REPLACED.

MAKING SANYO POA-LMP21 LAMP LAST LONGER

Extend the life of your newly installed Sanyo POA-LMP21 (service parts no 610 290 6939) by following these tips:

• Wait at least five minutes before turning the Sanyo PLC-SU20 projector off.
• Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
• Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP21 (service parts no 610 290 6939) and prevent the Sanyo PLC-SU20 from overheating.

The post Step-by-step instructions for Sanyo PLC-SU20 lamp replacement appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.