Sanyo POA-LMP31

Depending on usage and the regular maintenance done on your projector, a newly installed Sanyo POA-LMP31 (service parts no 610 289 8422) lamp should last between 1,000 to 3,000 hours before end of life.

Simplify your life and buy an authentic lamp. It’s worth paying the few extra dollars to be guaranteed a projector lamp that will work and will keep your warranty intact.

Remember:  When you purchase from a guaranteed supplier you’ll be getting a lamp specifically manufactured to meet the specifications of your projector. Knock-off lamps can be tempting because of their lower prices. But these generic lamps are usually made with counterfeit parts that are inferior and can damage the sensitive mechanisms in your Sanyo projector. The few dollars you save upfront may end up costing you more. Protect yourself against unreliable knock-offs using inferior and dangerous parts.

Projectors using the Sanyo POA-LMP31 lamp:

• Sanyo PLC-XW10

• Sanyo PLC-SW15

• Sanyo PLC-XW15

Scroll down for links to step-by-step instructions on replacing the Sanyo POA-LMP31 (service parts no 610 289 8422)  lamps for each of these projectors.

For step-by-step instructions on replacing your Sanyo POA-LMP31 (610 289 8422) lamp, click on your model listed below:

Sanyo PLC-XW10 Projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP31 (service parts no 610 289 8422) projector lamp for the Sanyo PLC-XW10.

Sanyo PLC-SW15 projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP31 (service parts no 610 289 8422) projector lamp for the Sanyo PLC-SW15.

Sanyo PLC-XW15 Projector

Click here for step-by-step instructions on how to change Sanyo POA-LMP31 (service parts no 610 289 8422) projector lamp for the Sanyo PLC-XW15.

The post When to replace your Sanyo POA-LMP31 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Sanyo PLC-XW15 Projector

Avoid the nightmare scenario of having your projector not work for the important presentation by knowing when it’s time to replace the lamp in your Sanyo PLC-XW15 projector. Watch for the yellow blinking light on the Lamp Replace Indicator on the top of your projector. This indicates your Sanyo POA-LMP31 (service parts no 610 289 8422) lamp is reaching the end of its life cycle and should be replaced immediately.

Follow our easy step-by-step instructions on how to replace the Sanyo POA-LMP31 (service parts no 610 289 8422) lamps for your Sanyo PLC-XW15 projector.

Before installation

Buy your  Sanyo POA-LMP31 (610 289 8422) from an authorized manufacturer and avoid the lure of lower-priced knock-off lamps. These counterfeit lamps are usually made with inferior parts that can damage your projector. They may end up costing you more if the damage the  sensitive mechanisms in your Sanyo PLC-XW15 projector. Buying from a legitimate source keeps your projector under warranty and gives you a solid guarantee.

Replacing the Sanyo POA-LMP31 Lamp Assembly

1. Turn off the projector and unplug the AC cord. Allow the Sanyo PLC-XW15 projector to cool to the touch. This can take between 45 to 60 minutes. Don’t open the projector when its still hot since these machines operate under high temperatures and you can burn yourself.

2. Gently turn over the  Sanyo PLC-XW15 to access the lamp cover at the bottom of the projector. Loosen the  screw holding the lamp cover in place. Remove the cover and put it to one side.

3. Inside you’ll find the Sanyo POA-LMP31 (6102898422) lamp cage. Loosen both screws holding the lamp cage in place. Grab the handle on the lamp cage and gently lift the lamp out of its socket. Place to one side. Be sure to dispose the used lamp properly through a local recycling program.

4. Take the new Sanyo POA-LMP31 (service parts no 610 289 8422) lamp cage by the handle—avoid touching the lamp surface as oil from your fingers can cause black spots to appear when the projector is turned on. Gently maneuver the lamp into place. Don’t force the lamp as this may damage the lamp.

5. Once the lamp is in, tighten both screws on the Sanyo POA-LMP31 (610 289 8422) Lamp Assembly. Make sure the screws have been tightened properly or the Sanyo PLC-XW15 projector will not turn on. Replace the Lamp Cover and tighten the screw.

6. Re-connect the power cord and turn on the Sanyo PLC-XW15. If the lamp does not turn on after the warm-up period, try re-installing the lamp. Reset the Lamp Replacement Monitor Timer  by following the instructions below.

NOTE: Be sure to properly recycle your used Sanyo POA-LMP31 (service parts no 610 289 8422) lamps. Since they contain mercury they can’t be placed into regular garbage.

How to reset the Sanyo PLC-XW15 Lamp Replacement Monitor Timer

In order for the projector to properly track the lamp life of your you’ll need to reset the Lamp Replacement Monitor Timer. Failure to do so can result in  the monitor not tracking the Sanyo POA-LMP31 (service parts no 610 289 8422) lamp life properly.

• Turn the Sanyo PLC-XW15 projector on.
• Press the MENU button to access the ON-SCREEN MENU.
• Press the POINT LEFT/RIGHT button to select the SETTING menu.
• Press the SELECT button to open the SETTING MENU option.
• Press the POINT DOWN button so the red-arrow appears.
• Move down to the LAMP AGE option. Press SELECT to open the next option.
• The message “Lamp replace monitor Reset?” will be displayed.
• Click on the option YES to reset the timer.

NOTE: RESET the Lamp Replacement Monitor Timer ONLY WHEN the lamp has been REPLACED.

Extend the life of the Sanyo POA-LMP31 lamp

Extend the life of your newly installed Sanyo POA-LMP31 (service parts no 610 289 8422) by following these tips:

• Wait at least five minutes before turning the Sanyo PLC-XW15 projector off.
• Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
• Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP31 (service parts no 610 289 8422) and prevent the Sanyo PLC-XW15 from overheating.

The post Change the lamp in your Sanyo PLC-XW15 projector appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Sanyo PLC-XW10 Projector

STEP-BY-STEP INSTRUCTIONS FOR SANYO PLC-XW10 LAMP REPLACEMENT

When the image on your Sanyo PLC-XW10 projector becomes extremely dark or an unnatural colour, it’s time to change the projector lamp. You’ll notice that Lamp Replacement Indicator on the top control panel will turn yellow.

The lifespan of your Sanyo PLC-XW10 projector lamp will vary depending on how much the projector is used and if the air filters are cleaned regularly.

You’ll need to install a new Sanyo POA-LMP31 (service parts no 610 289 8422) projector lamp.

Before installation:

Buy your Sanyo POA-LMP31 (610 289 8422) from an authorized manufacturer and avoid the lower-priced knock-off lamps. These knock-off lamps are usually made with counterfeit parts that are inferior and can damage the sensitive mechanisms in your Sanyo PLC-SW15 projector. They may end up costing you more if they damage your projector since they also void your waranty. Buying from a legitimate source keeps your projector under warranty and gives you a solid guarantee that the lamp you are installing is suitable for your projector.

Replacing the Sanyo POA-LMP31 Lamp Assembly

1. Turn off the projector and unplug the AC cord. Allow the Sanyo PLC-XW10 projector to cool to the touch. This can take between 45 to 60 minutes. Don’t open the projector when its still hot since these machines operate under high temperatures and you can burn yourself.

2. The lamp cover for the  Sanyo PLC-XW10 is  located at the bottom of the projector.  Gently turn the projector over and loosen the  screw holding the lamp cover. Remove the cover and put it to one side.

3. Inside you’ll find the SSanyo POA-LMP31 (service parts no 610 289 8422) lamp cage. Loosen both screws holding the lamp cage in place. Grab the handle on the lamp cage and gently lift the lamp out of its socket. Place to one side. Be sure to dispose the used lamp properly through a local recycling program.

4. Take the new Sanyo POA-LMP31 (610 289 8422) lamp cage by the handle—avoid touching the lamp surface as oil from your fingers can cause black spots to appear when the projector is turned on. Gently maneuver the lamp into place. Don’t force the lamp as this may damage it.

5. Once the lamp is in, tighten both screws on the Sanyo POA-LMP31 (6102898422) Lamp Assembly. Make sure the screws have been tightened properly or the Sanyo PLC-XW10  projector will not turn on. Replace the Lamp Cover and tighten the screw.

6. Re-connect the power cord and turn on the Sanyo PLC-XW10. If the lamp does not turn on after the warm-up period, try re-installing the lamp. Reset the Lamp Control mode found on the Setting menu.

NOTE: Be sure to properly recycle your used Sanyo POA-LMP31 (service parts no 610 289 8422) lamps. Since they contain mercury they can’t be placed into regular garbage.

Reset the Lamp Replacement Monitor Timer  by following the instructions below.

How to reset the Sanyo PLC-XW10 Lamp Replacement Monitor Timer

In order for the projector to properly track the lamp life of your you’ll need to reset the Lamp Replacement Monitor Timer. Failure to do so can result in  the monitor not tracking the Sanyo POA-LMP31 (service parts no 610 289 8422) lamp life properly.

• Turn the Sanyo PLC-XW10 projector on.
• Press the MENU button to access the ON-SCREEN MENU.
• Press the POINT LEFT/RIGHT button to select the SETTING menu.
• Press the SELECT button to open the SETTING MENU option.
• Press the POINT DOWN button so the red-arrow appears.
• Move down to the LAMP AGE option. Press SELECT to open the next option.
• The message “Lamp replace monitor Reset?” will be displayed.
• Click on the option YES to reset the timer.
• RESET the Lamp Replacement Monitor Timer ONLY WHEN the lamp has been REPLACED.

Extend the life of the Sanyo POA-LMP31 lamp

Extend the life of your newly installed Sanyo POA-LMP31 (service parts no 610 289 8422) by following these tips:

• Wait at least five minutes before turning the Sanyo PLC-XW10 projector off.
• Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
• Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP31 (service parts no 610 289 8422) and prevent the Sanyo PLC-XW10 from overheating.

The post How to Change the Lamp in a Sanyo PLC-XW10 Projector appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.