When it’s time to replace the Epson ELPLP41 in the Epson V11H285620, you’ll see the following warning signs:

• Dark image
• Image that has deteriorated
• On warning message appears on screen
• Lamp light flashes orange
• Lamp light turns red and stays on
• Check Lamp Usage

You can expect up to the 3000 hours of use with the Epson ELPLP41 before it needs to be replaced, if you have installed an authentic lamp.

The importance of authentic lamps

It’s critical to install a genuine Epson ELPLP41 rather than a compatible generic lamps. Although lower in price initially, generic, knock-off lamps end up costing much more in the long run. Counterfeit generic lamp have a shorter lamp life, damage the components in your projector, have poor picture quality and are prone to explosion. You also run the risk of being exposed to the carcinogenic substances such Krypton-85used in the making of these lamps.

Be sure the purchase an authentic Epson ELPLP41 projector lamp for your Epson PowerLite Home Cinema 700 projector. Save yourself unnecessary headaches and buy authentic from a recognized dealer. You’ll be getting a far superior product with a replacement guarantee and tech support.

Read more about the 7 Ways to Spot a Counterfeit Lamp.

Installing the Epson ELPLP41

Before installation:

• Turn power button off wait for light to stop flashing.
• Turn off power on Epson V11H285620 projector.
• Unplug the power cord.
• Allow the Epson V11H285620 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
• Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

The lamp cover is found on top of the Epson V11H285620 projector. Loosen the lamp cover screw — you can’t remove it only loosen it.

Slide the Epson V11H285620 lamp cover off.

Loosen the two screws holding the Epson ELPLP41 lamp in place.

Grab the Epson ELPLP41 lamp by the two indents on the lamp. Gently remove the lamp.

Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP41 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps! If you bought from an authentic manufacturer they will recycle the lamp for you at no extra cost (another reason to buy authentic lamps).

Gently insert the Epson ELPLP41 lamp making sure it’s facing the right way.

Tighten the screws on the new Epson ELPLP41 lamp.

Replace the lamp cover and tighten the screw on the Epson V11H285620 lamp cover.
You are now ready to reset the lamp timer.

Reset the lamp timer on the Epson V11H285620

Reset the Epson V11H285620 Lamp Replacement Counter only when the Epson ELPLP41 lamp has been replaced.

• Press the MENU button on the remote control. The Lamp Reset Menu will appear.
• Scroll down to the RESET LAMP HOURS. Press ENTER.
• A prompt appears asking if you want to replace the lamp.
• Select YES and press ENTER.
• Press MENU to exit.

Prolong the life of the Epson ELPLP41 lamp:

Extend the life of the newly installed Epson ELPLP41 with the following tips:

• Keep your air filters clean to avoid overheating the projector.
• Turn off the Epson V11H285620 projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
• Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
• Learn more with Top tips for extending DLP projector lamp life

The post Changing the Epson V11H285620 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Wondering which projectors are compatible with the Epson ELPLP41 projector lamp? Scroll down to find out more.

You can expect up to 3000 hours from your lamp if the Brightness Controls have been set to High. If the Brightness Control has been sent to Low, you will get up to 4,000 hours from the one lamp.

6 reasons to buy an authentic Epson ELPLP41

The Internet has been flooded with companies selling projector lamps. It’s critical to install a genuine Epson ELPLP41 rather than a compatible generic lamps. Although lower in price initially, generic, knock-off lamps end up costing much more in the long run

Many advertised their lamps as “generic and compatible” – a euphemism for a knock-off, copycat technology that produces an inferior and dangerous product. Don’t believe the cheap prices you see as there are hidden costs to installing generic lamps.

You get what you pay for and in the case of generic lamps it’s usually a long list of problems:

• shorter lamp life than original lamps
• toxic materials and carcinogenic parts including Krypton-85
• prone to explosions
• incompatibility causing damage to the sensitive electronics in your projectors
• no guarantee or refunds
• the warranty on your Epson projector will be voided.

Be sure the purchase an authentic Epson ELPLP41 projector lamp for your Epson projector. Save yourself unnecessary headaches and buy authentic from a recognized dealer. You’ll be getting a far superior product with a replacement guarantee and tech support.

Read more about the 7 Ways to Spot a Counterfeit Lamp.

Warning signs: when its time to replace

Watch for the signs that it’s time to replace the Epson ELPLP41 projector lamp:

• The projector image gets darker and starts to deteriorate.
• The projector lamp flashes red.
• The warning message REPLACE THE LAMP appears on screen.

A replacement warning message will also appear on screen. You can expect 4000 hours of lamp from the lamp depending on the settings and usage.

Compatible Projectors

The Epson ELPLP41 is compatible with:

Epson EMP-260, Epson EMP-X5, Epson EMP-X52, Epson EMP-X56, Epson EMP-X6, Epson EMP-S5, Epson EMP-S5+, Epson EMP-S52, Epson EX21, Epson EX30, Epson EX50, Epson EX70, Epson PowerLite Home Cinema 700, Epson PowerLite S5, Epson PowerLite S6, Epson PowerLite W6, Epson V11H285620, Epson EB-S6/EB-X6, Epson EB-W6, Epson EB-S62/EB-X62, Epson EMP-S6, Epson EMP-S6+

For step-by-step instructions on replacing your Epson ELPLP41 projector lamp, click on your projector listed below:

Click here for step-by-step instructions on how to change the Epson ELPLP41 projector lamp for the Epson EMP-260 projector.

Click here for step-by-step instructions on how to change the Epson ELPLP41 projector lamp for the Epson EMP-S6 projector.

Click here for step-by-step instructions on how to change the Epson ELPLP41 projector lamp for the Epson EMP-S6+ projector.

Click here for step-by-step instructions on how to change the Epson ELPLP41 projector lamp for the Epson EX21 projector.

Click here for step-by-step instructions on how to change the Epson ELPLP41 projector lamp for the Epson EX30 projector.

Click here for step-by-step instructions on how to change the Epson ELPLP41 projector lamp for the Epson EX50 projector.

Prolong the life of the Epson ELPLP41 lamp:

Extend the life of the newly installed Epson ELPLP41 with the following tips:

• Keep your air filters clean to avoid overheating the projector.
• Turn off the Epson projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
• Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
• Learn more with Top tips for extending DLP projector lamp life

The post Matching projectors with the Epson ELPLP41 lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

When it’s time to replace the Epson ELPLP41 in the Epson PowerLite Home Cinema 700, you’ll see the following warning signs:

• Dark image
• Image that has deteriorated
• On warning message appears on screen
• Lamp light flashes orange
• Lamp light turns red and stays on
• Check Lamp Usage

You can expect up to the 3000 hours of use with the Epson ELPLP41 before it needs to be replaced, if you have installed an authentic lamp.

The importance of authentic lamps

It’s critical to install a genuine Epson ELPLP41 rather than a compatible generic lamps. Although lower in price initially, generic, knock-off lamps end up costing much more in the long run. Counterfeit generic lamp have a shorter lamp life, damage the components in your projector, have poor picture quality and are prone to explosion. You also run the risk of being exposed to the carcinogenic substances such Krypton-85used in the making of these lamps.

Be sure the purchase an authentic Epson ELPLP41 projector lamp for your Epson PowerLite Home Cinema 700 projector. Save yourself unnecessary headaches and buy authentic from a recognized dealer. You’ll be getting a far superior product with a replacement guarantee and tech support.

Read more about the 7 Ways to Spot a Counterfeit Lamp.

Installing the Epson ELPLP41

Before installation:

• Turn power button off wait for light to stop flashing.
• Turn off power on Epson PowerLite Home Cinema 700 projector.
• Unplug the power cord.
• Allow the Epson PowerLite Home Cinema 700 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
• Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

The lamp cover is found on top of the Epson PowerLite Home Cinema 700 projector. Loosen the lamp cover screw — you can’t remove it only loosen it.

Slide the Epson PowerLite Home Cinema 700 lamp cover off.

Loosen the two screws holding the Epson ELPLP41 lamp in place.

Grab the Epson ELPLP41 lamp by the two indents on the lamp. Gently remove the lamp.

Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP41 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps! If you bought from an authentic manufacturer they will recycle the lamp for you at no extra cost (another reason to buy authentic lamps).

Gently insert the Epson ELPLP41 lamp making sure it’s facing the right way.

Tighten the screws on the new Epson ELPLP41 lamp.

Replace the lamp cover and tighten the screw on the Epson PowerLite Home Cinema 700 lamp cover.
You are now ready to reset the lamp timer.

Reset the lamp timer on the Epson PowerLite Home Cinema 700

Reset the Epson PowerLite Home Cinema 700 Lamp Replacement Counter only when the Epson ELPLP41 lamp has been replaced.

• Press the MENU button on the remote control. The Lamp Reset Menu will appear.
• Scroll down to the RESET LAMP HOURS. Press ENTER.
• A prompt appears asking if you want to replace the lamp.
• Select YES and press ENTER.
• Press MENU to exit.

Prolong the life of the Epson ELPLP41 lamp:

Extend the life of the newly installed Epson ELPLP41 with the following tips:

• Keep your air filters clean to avoid overheating the projector.
• Turn off the Epson PowerLite Home Cinema 700 projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
• Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
• Learn more with Top tips for extending DLP projector lamp life

The post Replacing the Epson PowerLite Home Cinema 700 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Follow this quick guide to install a new lamp in your Epson PowerLite W6 projector.

Scroll down for instructions!

Step 1: When is it time to replace the light?

When it’s time to replace the Epson ELPLP41 in the Epson PowerLite W6, you’ll see the following warning signs:

• Dark image
• Image that has deteriorated
• On warning message appears on screen
• Lamp light flashes orange
• Lamp light turns red and stays on
• Check Lamp Usage

You can expect up to the 3000 hours of use with the Epson ELPLP41 before it needs to be replaced, if you have installed an authentic lamp.

Step 2: Why buy an authentic lamp?

It’s critical to install a genuine Epson ELPLP41 rather than a compatible generic lamps. Although lower in price initially, generic, knock-off lamps end up costing much more in the long run and come with a whole set of problems that include:

• shorter lamp life than original lamps
• created with toxic materials and carcinogenic parts including Krypton-85
• prone to explosions
• can damage the sensitive electronics in your projectors
• no guarantee or refunds offered with generic lamps.

Be sure the purchase an authentic Epson ELPLP41 projector lamp for your Epson PowerLite W6 projector. Save yourself unnecessary headaches and buy authentic from a recognized dealer. You’ll be getting a far superior product with a replacement guarantee and tech support.

Read more about the 7 Ways to Spot a Counterfeit Lamp.

Step 3: How to replace the the Epson ELPLP41

Before installation:

• Turn power button off wait for light to stop flashing.
• Turn off power on Epson PowerLite W6 projector.
• Unplug the power cord.
• Allow the Epson PowerLite W6 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
• Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

1. The lamp cover is found on top of the Epson PowerLite W6 projector. Loosen the lamp cover screw — you can’t remove it only loosen it.

2. Slide the Epson PowerLite W6 lamp cover off.

3. Loosen the two screws holding the Epson ELPLP41 lamp in place.

4. Grab the Epson ELPLP41 lamp by the two indents on the lamp. Gently remove the lamp.

Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP41 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps! If you bought from an authentic manufacturer they will recycle the lamp for you at no extra cost (another reason to buy authentic lamps).

5. Gently insert the Epson ELPLP41 lamp making sure it’s facing the right way.

6. Tighten the screws on the new Epson ELPLP41 lamp.

7. Replace the lamp cover and tighten the screw on the Epson PowerLite W6 lamp cover.

8. You are now ready to reset the lamp timer.

Reset the lamp timer on the Epson PowerLite W6

Reset the Epson PowerLite W6 Lamp Replacement Counter only when the Epson ELPLP41 lamp has been replaced.

• Press the MENU button on the remote control. The Lamp Reset Menu will appear.
• Scroll down to the RESET LAMP HOURS. Press ENTER.
• A prompt appears asking if you want to replace the lamp.
• Select YES and press ENTER.
  Press MENU to exit.

Prolong the life of the Epson ELPLP41 lamp:

Extend the life of the newly installed Epson ELPLP41 with the following tips:

• Keep your air filters clean to avoid overheating the projector.
• Turn off the Epson PowerLite W6 projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
• Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.

Learn more with Top tips for extending DLP projector lamp life

The post A new Epson PowerLite W6 projector lamp in 3 easy steps appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

• Dark image
• Image that has deteriorated
• On warning message appears on screen
• Lamp light flashes orange
• Lamp light turns red and stays on
• Check Lamp Usage

You can expect up to the 3000 hours of use with the Epson ELPLP41 before it needs to be replaced, if you have installed an authentic lamp.

The importance of authentic lamps

It’s critical to install a genuine Epson ELPLP41 rather than a compatible generic lamps. Although lower in price initially, generic, knock-off lamps end up costing much more in the long run. Counterfeit generic lamp have a shorter lamp life, damage the components in your projector, have poor picture quality and are prone to explosion. You also run the risk of being exposed to the carcinogenic substances such Krypton-85used in the making of these lamps.

Be sure the purchase an authentic Epson ELPLP41 projector lamp for your Epson PowerLite S6 projector. Save yourself unnecessary headaches and buy authentic from a recognized dealer. You’ll be getting a far superior product with a replacement guarantee and tech support.

Read more about the 7 Ways to Spot a Counterfeit Lamp.

Installing the Epson ELPLP41

Before installation:

• Turn power button off wait for light to stop flashing.
• Turn off power on Epson PowerLite S6 projector.
• Unplug the power cord.
• Allow the Epson PowerLite S6 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
• Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

The lamp cover is found on top of the Epson PowerLite S6 projector. Loosen the lamp cover screw — you can’t remove it only loosen it.

Slide the Epson PowerLite S6 lamp cover off.

Loosen the two screws holding the Epson ELPLP41 lamp in place.

Grab the Epson ELPLP41 lamp by the two indents on the lamp. Gently remove the lamp.

Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP41 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps! If you bought from an authentic manufacturer they will recycle the lamp for you at no extra cost (another reason to buy authentic lamps).

Gently insert the Epson ELPLP41 lamp making sure it’s facing the right way.

Tighten the screws on the new Epson ELPLP41 lamp.

Replace the lamp cover and tighten the screw on the Epson PowerLite S6 lamp cover.
You are now ready to reset the lamp timer.

Reset the lamp timer on the Epson PowerLite S6

Reset the Epson PowerLite S6 Lamp Replacement Counter only when the Epson ELPLP41 lamp has been replaced.

• Press the MENU button on the remote control. The Lamp Reset Menu will appear.
• Scroll down to the RESET LAMP HOURS. Press ENTER.
• A prompt appears asking if you want to replace the lamp.
• Select YES and press ENTER.
  Press MENU to exit.

Prolong the life of the Epson ELPLP41 lamp:

Extend the life of the newly installed Epson ELPLP41 with the following tips:

• Keep your air filters clean to avoid overheating the projector.
• Turn off the Epson PowerLite S6 projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
• Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
• Learn more with Top tips for extending DLP projector lamp life

The post Your guide to replacing the Epson PowerLite S6 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Follow this quick guide to install a new lamp in your Epson PowerLite 78 projector.

Scroll down for instructions!

When is it time to replace the light?

Watch for the signs that the Epson ELPLP41 needs to be replaced in the Epson PowerLite 78:

• Dark image
• Image that has deteriorated
• On warning message appears on screen
• Lamp light flashes orange
• Lamp light turns red and stays on
• Check Lamp Usage

You can expect up to the 3000 hours of use with the Epson ELPLP41 before it needs to be replaced, if you have installed an authentic lamp.

The importance buying authentic lamps

It’s critical to install a genuine Epson ELPLP41 rather than a compatible generic lamps. Although lower in price initially, generic, knock-off lamps end up costing much more in the long run and come with a whole set of problems that include:

• shorter lamp life than original lamps
• created with toxic materials and carcinogenic parts including Krypton-85
• prone to explosions
• can damage the sensitive electronics in your projectors
• no guarantee or refunds offered with generic lamps.

Be sure the purchase an authentic Epson ELPLP41 projector lamp for your Epson PowerLite 78 projector. Save yourself unnecessary headaches and buy authentic from a recognized dealer. You’ll be getting a far superior product with a replacement guarantee and tech support.

Read more about the 7 Ways to Spot a Counterfeit Lamp.

Installing the Epson ELPLP41

Before installation:

• Turn power button off wait for light to stop flashing.
• Turn off power on Epson PowerLite 78 projector.
• Unplug the power cord.
• Allow the Epson PowerLite 78 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
• Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

The lamp cover is found on top of the Epson PowerLite 78 projector. Loosen the lamp cover screw — you can’t remove it only loosen it.

Slide the Epson PowerLite 78 lamp cover off.

Loosen the two screws holding the Epson ELPLP41 lamp in place.

Grab the Epson ELPLP41 lamp by the two indents on the lamp. Gently remove the lamp.

Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP41 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps! If you bought from an authentic manufacturer they will recycle the lamp for you at no extra cost (another reason to buy authentic lamps).

Gently insert the Epson ELPLP41 lamp making sure it’s facing the right way.

Tighten the screws on the new Epson ELPLP41 lamp.

Replace the lamp cover and tighten the screw on the Epson PowerLite 78 lamp cover.
You are now ready to reset the lamp timer.

Reset the lamp timer on the Epson PowerLite 78

Reset the Epson PowerLite 78 Lamp Replacement Counter only when the Epson ELPLP41 lamp has been replaced.

• Press the MENU button on the remote control. The Lamp Reset Menu will appear.
• Scroll down to the RESET LAMP HOURS. Press ENTER.
• A prompt appears asking if you want to replace the lamp.
• Select YES and press ENTER.
  Press MENU to exit.

Prolong the life of the Epson ELPLP41 lamp:

Extend the life of the newly installed Epson ELPLP41 with the following tips:

• Keep your air filters clean to avoid overheating the projector.
• Turn off the Epson PowerLite 78 projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
• Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
• Learn more with Top tips for extending DLP projector lamp life

The post How to replace the Epson PowerLite 78 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Follow this 3-step guide to a new Epson ELPLP41 projector lamp.

Step 1: Know when to replace

Watch for the signs that the Epson ELPLP41 needs to be replaced in the Epson Powerlite S5 projector:

• Dark image
• Image that has deteriorated
• On warning message appears on screen
• Lamp light flashes orange

You can expect up to the 3000 hours of use with the Epson ELPLP41 before it needs to be replaced, if you have installed an authentic lamp.

Step 2: Buy authentic

You’ll want to protect your investment and buy the best possible lamp for your Epson Powerlite S5 projector. Why jeopardize the projector to save a few dollars. Copycats lamps advertised as “generic compatible”  lamps may appear to be a bargain but they actually will end up costing more in the long run. Why? Because generic lamps actually have shorter lamp life than original lamps and are prone to explosions. Since copy cat manufacturers lack the genuine materials, they resort to using toxic materials and carcinogenic parts including Krypton-85.

Be sure to purchase an authentic Epson ELPLP41 projector lamp for your Epson Powerlite S5 projector and avoid incompatible parts that can damage the sensitive components in your projector. Save yourself unnecessary headaches You’ll be getting a far superior product with a replacement guarantee and tech support.

Read more about the 7 Ways to Spot a Counterfeit Lamp.

Step 3: Install the Epson ELPLP41

Before installation:

• Turn power button off wait for light to stop flashing.
• Turn off power switch on Epson Powerlite S5 projector.
• Unplug the power cord.
• Allow the Epson Powerlite S5 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
• Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

The lamp cover is found on top of the Epson Powerlite S5 projector. Loosen the lamp cover screw — you can’t remove it only loosen it.

Slide the Epson Powerlite 77C lamp cover off.

Loosen the two screws holding the Epson ELPLP41 lamp in place. You be able to remove them completely from the lamp — only loosen them enough to remove the lamp.

Grab the Epson ELPLP41 lamp by the two indents on the lamp. Gently remove the lamp by lifting straight up.

Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP41 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps! If you bought from an authentic manufacturer they will recycle the lamp for you at no extra cost (another reason to buy authentic lamps).

Gently insert the Epson ELPLP41 lamp following the rail guide. Make sure it’s facing the correct way. If it’s not facing the right way, the lamp will not go in properly. Push the lamp down firmly where you see the PUSH label. Tighten the screws on new Epson ELPLP41 lamp when it’s fitted properly into the projector

Replace the lamp cover and tighten the screw on the Epson Powerlite S5 projector lamp cover.
You are now ready to reset the lamp timer.

Reset the lamp timer on the Epson Powerlite S5 projector

Reset the Epson Powerlite S5 Lamp Replacement Counter only when the Epson ELPLP41 lamp has been replaced.

• Press the MENU button on the remote control. The Lamp Reset Menu will appear.
• Scroll down to the RESET LAMP HOURS. Press ENTER.
• A prompt appears asking if you want to replace the lamp.
• Select YES and press ENTER.
• Press MENU to exit.

Prolong the life of the Epson ELPLP41 lamp:

Extend the life of the newly installed Epson ELPLP41 with the following tips:

• Keep your air filters clean to avoid overheating the projector.
• Turn off the Epson Powerlite S5 projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
• Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
• Learn more with Top tips for extending DLP projector lamp life

The post 3 Steps to a new Epson Powerlite S5 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Note: These instructions can also be used for the Epson Powerlite 77 projector.

Step 1: When to replace

Watch for the signs that the Epson ELPLP41 needs to be replaced in the Epson Powerlite 77C projector:

• Dark image
• Image that has deteriorated
• On warning message appears on screen
• Lamp light flashes orange

You can expect up to the 3000 hours of use with the Epson ELPLP41 before it needs to be replaced, if you have installed an authentic lamp.

Step 2: Buy authentic

It’s critical to install a genuine Epson ELPLP41 rather than a compatible generic lamps. Although lower in price initially, generic, knock-off lamps end up costing much more in the long run. Counterfeit generic lamp have a shorter lamp life, damage the components in your projector, have poor picture quality and are prone to explosion. You also run the risk of being exposed to the carcinogenic substances such Krypton-85 used in the making of these lamps.

6 reasons to buy authentic

• generics have shorter lamp life than original lamps
• knock off lamps have been created with toxic materials and carcinogenic parts including Krypton-85
• generic lamps are prone to explosions
• copycat lamps can damage the sensitive electronics in your projectors
• no guarantee or refunds offered with generic lamps
• your warranty on the Epson Powerlite 77C will be void.

Be sure the purchase an authentic Epson ELPLP41 projector lamp for your Epson Powerlite 77C projector. Save yourself unnecessary headaches and buy authentic from a recognized dealer. You’ll be getting a far superior product with a replacement guarantee and tech support.

Read more about the 7 Ways to Spot a Counterfeit Lamp.

Step 3: Install the Epson ELPLP41

Before installation:

• Turn power button off wait for light to stop flashing.
• Turn off power switch on Epson Powerlite 77C projector.
• Unplug the power cord.
• Allow the Epson Powerlite 77C projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
• Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

The lamp cover is found on top of the Epson Powerlite 77C projector. Loosen the lamp cover screw — you can’t remove it only loosen it.

Slide the Epson Powerlite 77C lamp cover off.

Loosen the two screws holding the Epson ELPLP41 lamp in place. You not be able to remove them completely from the lamp — only loosen them enough to remove the lamp.

Grab the Epson ELPLP41 lamp by the two indents on the lamp. Gently remove the lamp by lifting straight up.

Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP41 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps! If you bought from an authentic manufacturer they will recycle the lamp for you at no extra cost (another reason to buy authentic lamps).

Gently insert the Epson ELPLP41 lamp following the rail guide. Make sure it’s facing the correct way. If it’s not facing the right way, the lamp will not go in properly. Push the lamp down firmly where you see the PUSH label. Tighten the screws on new Epson ELPLP41 lamp when it’s fitted properly into the projector

Replace the lamp cover and tighten the screw on the Epson Powerlite 77C projector  lamp cover.
You are now ready to reset the lamp timer.

Reset the lamp timer on the Epson Powerlite 77C projector

Reset the Epson Powerlite 77C Lamp Replacement Counter only when the Epson ELPLP41 lamp has been replaced.

• Press the MENU button on the remote control. The Lamp Reset Menu will appear.
• Scroll down to the RESET LAMP HOURS. Press ENTER.
• A prompt appears asking if you want to replace the lamp.
• Select YES and press ENTER.
  Press MENU to exit.

Prolong the life of the Epson ELPLP41 lamp:

Extend the life of the newly installed Epson ELPLP41 with the following tips:

• Keep your air filters clean to avoid overheating the projector.
• Turn off the Epson Powerlite 77C projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
• Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
• Learn more with Top tips for extending DLP projector lamp life

The post The easy way to replace the Epson Powerlite 77C projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Replacing the projector lamp for the Epson EB-S62/EB-X62 is quick and easy.

Follow this 3-step guide to replacing the Epson ELPLP41 projector lamp.

Step 1: Know when to replace

Watch for the signs that the Epson ELPLP41 needs to be replaced in the Epson EEB-S62/EB-X62 projector:

• Image that has deteriorated
• Dark image
• On warning message appears on screen
• Lamp light flashes orange
• Lamp light turns red and stays on
• Check Lamp Usage

To check the number of hours:

You can expect up to 3000 hours from your lamp if the Brightness Controls have been set to High, 4,000 hours if it has been set to Low.

• Press the MENU button
• Scroll down to highlight the INFO Menu. The number of hours let will be shown on screen.

Step 2: Buy authentic lamps

It’s critical to install a genuine Epson ELPLP41 rather than a compatible generic lamps. Although lower in price initially, generic, knock-off lamps end up costing much more in the long run and come with many problems that just add up to one giant headache. Be sure the purchase an authentic Epson ELPLP41 projector lamp for your EB-S62/EB-X62 projector. You’ll be getting a far superior product with a replacement guarantee and tech support.

6 reasons for avoiding generic lamps

• shorter lamp life than original lamps
• toxic materials and carcinogenic parts including Krypton-85
• prone to explosions
• incompatibility causing damage to the sensitive electronics in your projectors
• no guarantee or refunds

Read more about the 7 Ways to Spot a Counterfeit Lamp.

Step 3: Install the Epson ELPLP41

Before installation:

• Turn power button off wait for light to stop flashing.
• Turn off power swtich on the back of the Epson EB-S62/EB-X62 projector.
• Unplug the power cord.
• Allow the Epson EB-S62/EB-X62 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
• Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

The lamp cover is found on top of the Epson EB-S62/EB-X62 projector. Loosen the lamp cover screw — you can’t remove it only loosen it.

Slide the Epson EB-S62/EB-X62 lamp cover off.

Loosen the two screws holding the Epson ELPLP41 lamp in place.

Grab the Epson ELPLP41 lamp by the two indents on the lamp. Gently remove the lamp.

Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP41 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps! If you bought from an authentic manufacturer they will recycle the lamp for you at no extra cost (another reason to buy authentic lamps).

Gently insert the Epson ELPLP41 lamp making sure it’s facing the right way.

Tighten the screws on the new Epson ELPLP41 lamp.

Replace the lamp cover and tighten the screw on the lamp cover.
You are now ready to reset the lamp timer.

Reset the lamp timer on the Epson EB-S62/EB-X62

Reset the EB-S62/EB-X62 Lamp Replacement Counter only when the Epson ELPLP41 lamp has been replaced.

• Press the MENU button on the remote control. The Lamp Reset Menu will appear.
• Scroll down to the RESET LAMP HOURS. Press ENTER.
• A prompt appears asking if you want to replace the lamp.
• Select YES and press ENTER.
  Press MENU to exit.

Prolong the life of the Epson ELPLP41 lamp:

Extend the life of the newly installed Epson ELPLP41 with the following tips:

• Keep your air filters clean to avoid overheating the projector.
• Turn off the EB-S62/EB-X62 projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
• Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
• Learn more with Top tips for extending DLP projector lamp life.

The post 3 steps to replacing the Epson EB-S62/EB-X62 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Follow our 3-step guide to replace the lamp in your Epson EMP-S6+ projector? It’s simple to do.

Step 1: Knowing when to replace

Watch for the signs that the Epson ELPLP41 needs to be replaced in the Epson EMP-S6+ projector:

• Dark image
• Image that has deteriorated
• On warning message appears on screen
• Lamp light flashes orange
• Lamp light turns red and stays on
• Check Lamp Usage

Check the number of hours:

You can expect up to 3000 hours from your lamp if the Brightness Controls have been set to High. If Brightness Controls has been set to Low, you can expect, 4,000 hours.

• Press the MENU button
• Scroll down to highlight the INFO Menu. The number of hours let will be shown on screen.

Step 2: Finding the correct lamp

Why buy authentic? You’ll want to protect your investment and buy the best possible lamp for your Epson EMP-S6+ projector. Why jeopardize the projector to save a few dollars. Copycats lamps advertised as “generic compatible” lamps may appear to be a bargain but they actually will end up costing more in the long run. Why? Because generic lamps actually have shorter lamp life than original lamps and are prone to explosions. Since copy cat manufacturers lack the genuine materials, they resort to using toxic materials and carcinogenic parts including Krypton-85.

Be sure to purchase an authentic Epson ELPLP41 projector lamp for your Epson EMP-S6+ projector and avoid incompatible parts that can damage the sensitive components in your projector. Save yourself unnecessary headaches You’ll be getting a far superior product with a replacement guarantee and tech support.

Step 3: How to install the Epson ELPLP41

Before installation:

• Turn power button off wait for light to stop flashing.
• Turn off power swtich on the back of the Epson EMP-S6+ projector.
• Unplug the power cord.
• Allow the Epson EMP-S6+ projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
• Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

The lamp cover is found on top of the Epson EMP-S6+ projector. Loosen the lamp cover screw — you can’t remove it only loosen it.

Slide the Epson EMP-S6+ lamp cover off.

Loosen the two screws holding the Epson ELPLP41 lamp in place.

Grab the Epson ELPLP41 lamp by the two indents on the lamp. Gently remove the lamp.

Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The Epson ELPLP41 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps! If you bought from an authentic manufacturer they will recycle the lamp for you at no extra cost (another reason to buy authentic lamps).

Gently insert the Epson ELPLP41 lamp making sure it’s facing the right way.

Tighten the screws on the new Epson ELPLP41 lamp.

Replace the lamp cover and tighten the screw on the Epson EMP-S6+ lamp cover.
You are now ready to reset the lamp timer.

Reset the lamp timer on the Epson EMP-S6+

Reset the Epson EMP-S6+ Lamp Replacement Counter only when the Epson ELPLP41 lamp has been replaced.

• Press the MENU button on the remote control. The Lamp Reset Menu will appear.
• Scroll down to the RESET LAMP HOURS. Press ENTER.
• A prompt appears asking if you want to replace the lamp.
• Select YES and press ENTER.
  Press MENU to exit.

Prolong the life of the Epson ELPLP41 lamp:

Extend the life of the newly installed Epson ELPLP41 with the following tips:

• Keep your air filters clean to avoid overheating the projector.
• Turn off the Epson EMP-S6+ projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
• Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
• Learn more with Top tips for extending DLP projector lamp life

The post 3 Steps to a new Epson EMP-S6 Plus projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.