Check out this list to see if your Epson projector is compatible with the Epson ELPLP46 lamp. Before you install any Epson ELPLP46 lamp look for the seal of approval and be sure to buy authentic:

• authentic lamps have a longer life than generics
• generic lamps are created with toxic materials and have NO saftey standards
• authentic last the entire 3000 hours and will not explode
• copycat lamps can damage the sensitive electronics in your projectors
• generics don’t come with a guarantee or tech support. Getting a refund can be a hassle.
• your warranty on the Epson will be void if you install a generic lamp.
• Find out how to protect yourself from being tricked into buying counterfeit lamps.

Find these lamp sold on Amazon by these authorized dealers:

• ELP-LP46 Epson Projector Lamp Replacement. Projector Lamp Assembly with High Quality Genuine Original Ushio Bulb Inside.
• Epson ELPLP46 Projector Assembly with High Quality Osram Projector Bulb Inside
• Epson Compatible Manufacturer ELPLP46 E-Series Replacement Lamp
  

Compatible projectors with the Epson ELPLP46 lamp

The Epson ELPLP46 lamp is compatible with the following Epson projectors:

Epson EB-G5200, Epson EB-G5200W, Epson EB-G5300, Epson EB-G5350, Epson G5200, Epson G5200WNL,Epson G5350NL, Epson PowerLite Pro G5200, Epson PowerLite Pro G5200WNL, Epson PowerLite Pro G5350, Epson PowerLite Pro G5350NL

For step-by-step instructions on replacing your Epson ELPLP46 lamp, click on your projector listed below:

Click here for step-by-step instructions on how to change the Epson ELPLP46 projector lamp for the Epson EB-G5200 projector.

Click here for step-by-step instructions on how to change the Epson ELPLP46 projector lamp for the Epson EB-G5200W projector.

Click here for step-by-step instructions on how to change the Epson ELPLP46 projector lamp for the Epson EB-G5300 projector.

Click here for step-by-step instructions on how to change the Epson ELPLP46 projector lamp for the Epson EB-G5350 projector.

Click here for step-by-step instructions on how to change the Epson ELPLP46 projector lamp for the Epson G5200 projector.

How to extend the life of the Epson ELPLP46 lamp:

Extend the life of the newly installed Epson ELPLP46 with the following tips:

• Keep your air filters clean to avoid overheating the projector.
• Turn off the Epson projectors and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
• Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
• Set the Brightness Mode to low or Econo Mode to extend lamp life.
• Learn more with Top tips for extending DLP projector lamp life.

The post Find projectors compatible with the Epson ELPLP46 lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

This kind shows you how to install a replacement Epson PowerLite Pro G5350 projector lamp. Your replacement lamp is Epson ELPLP46.

Find these lamp sold on Amazon by these authorized dealers:

• ELP-LP46 Epson Projector Lamp Replacement. Projector Lamp Assembly with High Quality Genuine Original Ushio Bulb Inside.
• Epson ELPLP46 Projector Assembly with High Quality Osram Projector Bulb Inside
• Epson Compatible Manufacturer ELPLP46 E-Series Replacement Lamp
  

STEP 1: End of life warnings

Tracking lamp life

The life span of the Epson ELPLP46 is 2000 hours when Brightness Control is set to High (which is the default) or 3000 hours if the Brightness Control is set to Low. Track the life of the lamp in the Epson PowerLite Pro G5350:

• Press the MENU button on either the remote control or on the projector’s control panel.
• Scroll down to INFO to show the number of hours.
• You can see the number of hours left on both High and Low Brightness.

To reset the lamp Brightness:

• Press the MENU button on either the remote control or on the projector’s control panel.
• Scroll down to SETTINGS menu. Press ENTER.
• Scroll down to highlight BRIGHTNESS CONTROL. Press ENTER.
• Press the arrow key to change from High to Low.
• Press ENTER to save the change.

When the Epson ELPLP46 is approaching end of life you’ll start to see warnings signs:

• A screen that is gradually dimming or deteriorating.
• Colour in the image appears dark or off colour.
• “Replace the lamp” warning flashing on screen.
• Lamp light flashing a steady orange.

Replace the Epson ELPLP46 lamp immediately so you don’t run the risk of having the lamp explode in the Epson PowerLite Pro G5350 projector.

STEP 2: Buy authentic

What’s the difference between an authentic Epson ELPLP46 and a generic lamp? Quality, price and reliability!

With their bargain prices and easy availability, generic lamps can be a real temptation. However, inferior workmanship means a inferior product, that doesn’t last the full 2000 hours making generics a poor choice despite the great price tag. These lamps can’t be calibrated properly and they they can seriously damage the optics in your Epson PowerLite Pro G5350. But the main reason to avoid generic lamps are the health hazard they pose due to their toxic materials.

Keep the warranty valid on Epson PowerLite Pro G5350. Buy an authentic lamp from a recognized dealer who proudly displays the seal of approval. Learn how to buy authentic.

STEP 3: Replacing the Epson ELPLP46 lamp

Before installation follow these important safety tips:

• Turn power button off and after the Epson PowerLite Pro G5350 has beeped twice unplug the power cord.
• The Epson PowerLite Pro G5350 should be cool to the touch. DO NOT attempt to change the Epson ELPLP46 if the projector is still hot. You can be badly burned if you don’t wait for the projector to cool.

IMPORTANT: Do not operate the projectors the lamps is removed as this may result in malfunctions, fire hazard and other accidents.

• Loosen the screws on the Epson PowerLite G5350 projector using the screwdriver provided.
• NOTE: Even when the lamp cover is removed in remains attached to the projector to prevent it from falling should the projector be mounted to the ceiling.

• Loosen the two screws holding the Epson ELPLP46 lamp in place. Theses screws also don’t completely come out.

• Grab the handle in the middle of the Epson ELPLP46 and slowly pull out the lamp out of the Epson PowerLite Pro G5350 projector.
• Don’t use excessive force or the lamp could break.
• Read this article about what to do if lamp breaks inside the projector.

• Gently insert the new Epson ELPLP46 lamp into the Epson PowerLite G5350 projector.
• Avoid touching the actual lamp since your fingerprints will cause black out spots to appear when the projector starts working.
• Tighten the screws on the Epson ELPLP46 lamp. Be sure not to tighten too much or the lamp may not work.
• Replace the lamp cover and tighten the screw on the Epson ELPLP46 projector lamp cover.

NOTE: The Epson ELPLP46 lamp contains mercury and needs to be properly recycled. Don’t thrown the used lamp into your regular garbage.

You are now ready to reset the lamp timer.

Resetting the Epson PowerLite Pro G5350 Lamp Timer

It’s important to reset the PowerLite Pro G5350 has a lamp timer each time a new lamp is installed so the projector can accurately track the Epson ELPLP46 lamp. Never use the Epson ELPLP46 lamp beyond its recommended usage as this can damage the Epson Pro G5350 projector beyond repair.

• Press the MENU button on either the remote control or on the projector’s control panel.
• Scroll down to the RESET option. Press Enter to bring up the reset screen.
• Scroll down to RESET LAMP HOURS.
• A second prompt screen will appear asking for confirmation. Scroll over to the YES option. Press ENTER.
• Press MENU to exit.

Extending the life of your Epson ELPLP46 lamp

Follow this simple tips to make your Epson ELPLP46 lamp last even longer:

• Keep your air filters clean to avoid overheating the projector.
• Turn off the PowerLite Pro G5350 projector and let it stand for at least one hour ever 24 hours.
• An average use of four to five hours per day will ensure longer lamp life.
• Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
• Set the Brightness Mode to low.
• Learn more with Top tips for extending DLP projector lamp life

The post Change the Epson PowerLite Pro G5350 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Start off with buying an authentic Epson EB-G5200 projector lamp. What’s the difference between an authentic projector lamp and a generic version? Quality, price and reliability!

With their bargain prices and easy availability, generic lamps can be a real temptation. However, generic lamps are plagued with problems that may them a poor choice despite the great price tag. The main reason to avoid these so-called compatible, generic lamps include:

• inferior workmanship means a inferior product
• unable to be calibrated properly they can seriously damage the optics in your Epson EB-G5200.
  
• don’t last the full 2000 hours.
• present a serious health hazard due to their toxic materials.
• void the warranty on your Epson EB-G5200 projector.

Buy an authentic lamp from a recognized dealer who proudly displays the seal of approval. Protect yourself and buy authentic. Your replacement lamp is Epson ELPLP46.

Find these lamp sold on Amazon by these authorized dealers:

• ELP-LP46 Epson Projector Lamp Replacement. Projector Lamp Assembly with High Quality Genuine Original Ushio Bulb Inside.
• Epson ELPLP46 Projector Assembly with High Quality Osram Projector Bulb Inside
• Epson Compatible Manufacturer ELPLP46 E-Series Replacement Lamp
  

End of life warning signs

The life span of the Epson ELPLP46 is 2000 hours when Brightness Control is set to High (which is the default) or 3000 hours if the Brightness Control is set to Low.

When the Epson ELPLP46 is approaching end of life you’ll start to see warnings signs:

• A screen that is gradually dimming or deteriorating.
• Colour in the image appears dark or off colour.
• “Replace the lamp” warning flashing on screen.
• Lamp light flashing a steady orange.

Replace the Epson ELPLP46 lamp immediately so you don’t run the risk of having the lamp explode.

Tracking lamp life

To track the life of your lamp check the number of hours it’s been in use:

• Press the MENU button on either the remote control or on the projector’s control panel.
• Scroll down to INFO to show the number of hours.
• You can see the number of hours left on both High and Low Brightness.

To reset the lamp Brightness:

• Press the MENU button on either the remote control or on the projector’s control panel.
• Scroll down to SETTINGS menu. Press ENTER.
• Scroll down to highlight BRIGHTNESS CONTROL. Press ENTER.
• Press the arrow key to change from High to Low.
• Press ENTER to save the change.

Replacing the Epson ELPLP46 lamp

Before installation follow these important safety tips:

• Turn power button off and after the Epson EB-G5200 has beeped twice unplug the power cord.
• The Epson EB-G5200 should be cool to the touch. DO NOT attempt to change the Epson ELPLP46 if the projector is still hot. You can be badly burned if you don’t wait for the projector to cool.

IMPORTANT: Do not operate the projectors the lamps is removed as this may result in malfunctions, fire hazard and other accidents.

• Loosen the screws on the Epson Epson EB-G5200 projector using the screw drive provided.
• NOTE: Even when the lamp cover is removed in remains attached to the projector to prevent it from falling should the projector be mounted to the ceiling.

• Loosen the two screws holding the Epson ELPLP46 lamp in place. These screws also don’t completely come out.

• Grab the handle in the middle of the Epson ELPLP46 and slowly pull out the lamp.
• Don’t use excessive force or the lamp could break.
• Read this article about what to do if lamp breaks inside the projector.

• Gently insert the new Epson ELPLP46 lamp into the Epson EB-G5200 projector.
• Avoid touching the actual lamp since your fingerprints will cause black out spots to appear when the projector starts working.
• NOTE: The Epson ELPLP46 lamp contains mercury and needs to be properly recycled. Don’t thrown the used lamp into your regular garbage.

• Tighten the screws on the Epson ELPLP46 lamp. Be sure not to tighten too much or the lamp may not work.

• Replace the lamp cover and tighten the screw on the Epson ELPLP46 projector lamp cover.

You are now ready to reset the lamp timer.

Resetting the Epson EB-G5200 Lamp Timer

The Epson Epson EB-G5200 has a lamp timer that tracks the number of hours left for the Epson ELPLP46. Every time you install a new Epson ELPLP46 lamp you must reset the lamp timer to zero. Don’t use the Epson ELPLP46 lamp beyond its recommended usage as this can damage the EpsonEpson EB-G5200 projector.

• Press the MENU button on either the remote control or on the projector’s control panel.
• Scroll down to the RESET option. Press Enter to bring up the reset screen.
• Scroll down to RESET LAMP HOURS.
• A second prompt screen will appear asking for confirmation. Scroll over to the YES option. Press ENTER.
• Press MENU to exit.

Extending the life of your Epson ELPLP46 lamp

Follow this simple tips to make your Epson ELPLP46 lamp last even longer:

• Keep your air filters clean to avoid overheating the projector.
• Turn off the Epson EB-G5200 projector and let it stand for at least one hour ever 24 hours.
• An average use of four to five hours per day will ensure longer lamp life.
• Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
• Set the Brightness Mode to low.
• Learn more with Top tips for extending DLP projector lamp life

The post Install a new Epson EB-G5200 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Start off with buying an authentic Epson ELPLP 31 lamp. What’s the difference between an authentic Epson ELPLP 31 lamp and a generic version. Quality, price and reliability!

With their bargain prices and easy availability, generic lamps can be a real temptation. However, generic lamps are plagued with problems that may them a poor choice despite the great price tag. The main reason to avoid these so-called compatible, generic lamps include:

• inferior workmanship means a inferior product
• unable to be calibrated properly they can seriously damage the optics in your Epson EB-G5200W.
  
• don’t last the full 2000 hours.
• present a serious health hazard due to their toxic materials.
• void the warranty on your Epson EB-G5200W projector.

Buy an authentic lamp from a recognized dealer who proudly displays the seal of approval. Protect yourself and buy authentic. Your replacement lamp is Epson ELPLP46.

End of life warning signs

The life span of the Epson ELPLP46 is 2000 hours when Brightness Control is set to High (which is the default) or 3000 hours if the Brightness Control is set to Low.

When the Epson ELPLP46 is approaching end of life you’ll start to see warnings signs:

• A screen that is gradually dimming or deteriorating.
• Colour in the image appears dark or off colour.
• “Replace the lamp” warning flashing on screen.
• Lamp light flashing a steady orange.

Replace the Epson ELPLP46 lamp immediately so you don’t run the risk of having the lamp explode.

Tracking lamp life

To track the life of your lamp check the number of hours it’s been in use:

• Press the MENU button on either the remote control or on the projector’s control panel.
• Scroll down to INFO to show the number of hours.
• You can see the number of hours left on both High and Low Brightness.

To reset the lamp Brightness:

• Press the MENU button on either the remote control or on the projector’s control panel.
• Scroll down to SETTINGS menu. Press ENTER.
• Scroll down to highlight BRIGHTNESS CONTROL. Press ENTER.
• Press the arrow key to change from High to Low.
• Press ENTER to save the change.

Replacing the Epson ELPLP46 lamp

Before installation follow these important safety tips:

• Turn power button off and after the Epson EB-G5200W has beeped twice unplug the power cord.
• The Epson Epson EB-G5200W should be cool to the touch. DO NOT attempt to change the Epson ELPLP46 if the projector is still hot. You can be badly burned if you don’t wait for the projector to cool.

IMPORTANT: Do not operate the projectors the lamps is removed as this may result in malfunctions, fire hazard and other accidents.

• Loosen the screws on the Epson Epson EB-G5200W projector using the screw drive provided.
• NOTE: Even when the lamp cover is removed in remains attached to the projector to prevent it from falling should the projector be mounted to the ceiling.

• Loosen the two screws holding the Epson ELPLP46 lamp in place. These screws also don’t completely come out.

• Grab the handle in the middle of the Epson ELPLP46 and slowly pull out the lamp.
• Don’t use excessive force or the lamp could break.
• Read this article about what to do if lamp breaks inside the projector.

• Gently insert the new Epson ELPLP46 lamp into the Epson EB-G5200W projector.
• Avoid touching the actual lamp since your fingerprints will cause black out spots to appear when the projector starts working.
• NOTE: The Epson ELPLP46 lamp contains mercury and needs to be properly recycled. Don’t thrown the used lamp into your regular garbage. Contact your authentic manufacturer and they they assist you in getting the lamp to the right recycling facility.

• Tighten the screws on the Epson ELPLP46 lamp. Be sure not to tighten too much or the lamp may not work.

• Replace the lamp cover and tighten the screw on the Epson ELPLP46 projector lamp cover.

You are now ready to reset the lamp timer.

Resetting the Epson EB-G5200W Lamp Timer

The Epson Epson EB-G5200W has a lamp timer that tracks the number of hours left for the Epson ELPLP46. Every time you install a new Epson ELPLP46 lamp you must reset the lamp timer to zero. Don’t use the Epson ELPLP46 lamp beyond its recommended usage as this can damage the Epson Epson EB-G5200W projector.

• Press the MENU button on either the remote control or on the projector’s control panel.
• Scroll down to the RESET option. Press Enter to bring up the reset screen.
• Scroll down to RESET LAMP HOURS.
• A second prompt screen will appear asking for confirmation. Scroll over to the YES option. Press ENTER.
• Press MENU to exit.

Extending the life of your Epson ELPLP46 lamp

Follow this simple tips to make your Epson ELPLP46 lamp last even longer:

• Keep your air filters clean to avoid overheating the projector.
• Turn off the Epson EB-G5200W projector and let it stand for at least one hour ever 24 hours.
• An average use of four to five hours per day will ensure longer lamp life.
• Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
• Set the Brightness Mode to low.
• Learn more with Top tips for extending DLP projector lamp life

The post Installation guide for the Epson ELPLP 31 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Be sure to invest in an authentic Epson G5350NL projector lamp.

When do I need to change the lamp?

When the Epson ELPLP46 is approaching end of life you’ll start to see warnings signs:

• A screen that is gradually dimming or deteriorating.
• Colour in the image appears dark or off colour.
• “Replace the lamp” warning flashing on screen.
• Lamp light flashing a steady orange.

Replace the Epson ELPLP46 lamp immediately so you don’t run the risk of having the lamp explode.

Tracking lamp life

The life span of the Epson ELPLP46 is 2000 hours when Brightness Control is set to High (which is the default) or 3000 hours if the Brightness Control is set to Low. To track the life of your lamp check the number of hours it’s been in use:

• Press the MENU button on either the remote control or on the projector’s control panel.
• Scroll down to INFO to show the number of hours.
• You can see the number of hours left on both High and Low Brightness.

To reset the lamp Brightness:

• Press the MENU button on either the remote control or on the projector’s control panel.
• Scroll down to SETTINGS menu. Press ENTER.
• Scroll down to highlight BRIGHTNESS CONTROL. Press ENTER.
• Press the arrow key to change from High to Low.
• Press ENTER to save the change.

Be ready with an authentic lamp

What’s the difference between an authentic Epson ELPLP46 and a generic version. Quality, price and reliability!

With their bargain prices and easy availability, generic lamps can be a real temptation. However, generic lamps are plagued with problems that may them a poor choice despite the great price tag. The main reason to avoid these so-called compatible, generic lamps include:

• inferior workmanship means a inferior product
• unable to be calibrated properly they can seriously damage the optics in your Epson G5350NL.
  
• don’t last the full 2000 hours.
• present a serious health hazard due to their toxic materials.
• void the warranty on your Epson G5350NL projector.

Buy an authentic lamp from a recognized dealer who proudly displays the seal of approval. Protect yourself and buy authentic.

Replacing the Epson ELPLP46 lamp

Before installation follow these important safety tips:

• Turn power button off and after the Epson G5350NL has beeped twice unplug the power cord.
• The Epson G5350NL should be cool to the touch. DO NOT attempt to change the Epson ELPLP46 if the projector is still hot. You can be badly burned if you don’t wait for the projector to cool.

IMPORTANT: Do not operate the projectors the lamps is removed as this may result in malfunctions, fire hazard and other accidents.

• Loosen the screws on the Epson G5350NL projector using the screw drive provided.
• NOTE: Even when the lamp cover is removed in remains attached to the projector to prevent it from falling should the projector be mounted to the ceiling.

• Loosen the two screws holding the Epson ELPLP46 lamp in place. Theses screws also don’t completely come out.

• Grab the handle in the middle of the Epson ELPLP46 and slowly pull out the lamp.
• Don’t use excessive force or the lamp could break.
• Read this article about what to do if lamp breaks inside the projector.

• Gently insert the new Epson ELPLP46 lamp into the Epson  G5350NL projector.
• Avoid touching the actual lamp since your fingerprints will cause black out spots to appear when the projector starts working.
• Tighten the screws on the Epson ELPLP46 lamp. Be sure not to tighten too much or the lamp may not work.
• Replace the lamp cover and tighten the screw on the Epson ELPLP46 projector lamp cover.

NOTE: The Epson ELPLP46 lamp contains mercury and needs to be properly recycled. Don’t thrown the used lamp into your regular garbage. Contact your authentic manufacturer and they they assist you in getting the lamp to the right recycling facility.

You are now ready to reset the lamp timer.

Resetting the Epson PG5350NL Lamp Timer

The Epson G5350NL has a lamp timer that tracks the number of hours left for the Epson ELPLP46. Every time you install a new Epson ELPLP46 lamp you must reset the lamp timer to zero. Don’t use the Epson ELPLP46 lamp beyond its recommended usage as this can damage the Epson G5350NL projector.

• Press the MENU button on either the remote control or on the projector’s control panel.
• Scroll down to the RESET option. Press Enter to bring up the reset screen.
• Scroll down to RESET LAMP HOURS.
• A second prompt screen will appear asking for confirmation. Scroll over to the YES option. Press ENTER.

• Press MENU to exit

Extending the life of your Epson ELPLP46 lamp

Follow this simple tips to make your Epson ELPLP46 lamp last even longer:

• Keep your air filters clean to avoid overheating the projector.
• Turn off the Epson G5350NL projector and let it stand for at least one hour ever 24 hours.
• An average use of four to five hours per day will ensure longer lamp life.
• Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
• Set the Brightness Mode to low.
• Learn more with Top tips for extending DLP projector lamp life

The post How to replace the Epson G5350NL projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

It’s simple and fast to replace the Epson G5200 projector lamp. Your replacement lamp is Epson ELPLP46.

 Step 1: Track the lamp life so you know when to replace

The life span of the Epson G5200 projector lamp is 2000 hours when the Brightness Control is set to High (which is the default) or 3000 hours if the Brightness Control is set to Low. To track the life of your lamp check the number of hours it’s been in use:

• Press the MENU button on either the remote control or on the projector’s control panel.
• Scroll down to INFO to show the number of hours.
• You can see the number of hours left on both High and Low Brightness.

To reset the lamp Brightness:

• Press the MENU button on either the remote control or on the projector’s control panel.
• Scroll down to SETTINGS menu. Press ENTER.
• Scroll down to highlight BRIGHTNESS CONTROL. Press ENTER.
• Press the arrow key to change from High to Low.
• Press ENTER to save the change.

End of life warning signs

When the Epson G5200 projector lamp is approaching end of life you’ll start to see warnings signs:

• A screen that is gradually dimming or deteriorating.
• Colour in the image appears dark or off colour.
• “Replace the lamp” warning flashing on screen.
• Lamp light flashing a steady orange.

Replace the Epson ELPLP46 lamp immediately so you don’t run the risk of having the lamp explode.

Step 2: Buy authentic!

It’s important that you buy an authentic lamp from a recognized dealer who proudly displays the seal of approval. The market has been flooded with copycat counterfeit lamps claiming to be compatible with your Epson G5200 projector. Unfortunately that is false advertising since these generic lamps can harm the sensitive optics in your projector. They actually have a shorter lamp life and are prone to explosions. Probably the most disturbing thing about generic lamps bought off the Internet is the health hazards they pose. They’ve been created with toxic substitutes but also don’t have the safety guards in place to protect your eyesight from damage. Protect yourself and buy authentic.

Step 3: Replacing the Epson ELPLP46 lamp

Before installation follow these important safety tips:

• Turn power button off and after the Epson G5200 has beeped twice unplug the power cord.
• The Epson G5200 should be cool to the touch. DO NOT attempt to change the Epson ELPLP46 if the projector is still hot. You can be badly burned if you don’t wait for the projector to cool.

IMPORTANT: Do not operate the projectors the lamps is removed as this may result in malfunctions, fire hazard and other accidents.

• Loosen the screws on the Epson G5200 projector using the screw drive provided.
• NOTE: Even when the lamp cover is removed in remains attached to the projector to prevent it from falling should the projector be mounted to the ceiling.

• Loosen the two screws holding the Epson ELPLP46 lamp in place. Theses screws also don’t completely come out.

• Grab the handle in the middle of the Epson ELPLP46 and slowly pull out the lamp. Don’t use excessive force or the lamp could break.
• Read this article about what to do if lamp breaks inside the projector.
• NOTE: The Epson ELPLP46 lamp contains mercury and needs to be properly recycled. Don’t thrown the used lamp into your regular garbage. Contact your authentic manufacturer and they they assist you in getting the lamp to the right recycling facility.

• Gently insert the new Epson ELPLP46 lamp into the Epson G5200 projector.
• Avoid touching the actual lamp since your fingerprints will cause black out spots to appear when the projector starts working.
• Tighten the screws on the Epson ELPLP46 lamp. Be sure not to tighten too much or the lamp may not work.
• Replace the lamp cover and tighten the screw on the Epson G5200 projector projector lamp cover.

You are now ready to reset the lamp timer.

Resetting the Epson G5200 Lamp Timer

The Epson G5200 has a lamp timer that tracks the number of hours left for the Epson ELPLP46. Every time you install a new Epson ELPLP46 lamp you must reset the lamp timer to zero. Don’t use the Epson ELPLP46 lamp beyond its recommended usage as this can damage the Epson G5200 projector.

• Press the MENU button on either the remote control or on the projector’s control panel.
• Scroll down to the RESET option. Press Enter to bring up the reset screen.
• Scroll down to RESET LAMP HOURS.
• A second prompt screen will appear asking for confirmation. Scroll over to the YES option. Press ENTER.
• Press MENU to exit.

Extending the life of your Epson ELPLP46 lamp

Follow this simple tips to make your Epson ELPLP46 lamp last even longer:

• Keep your air filters clean to avoid overheating the projector.
• Turn off the Epson G5200WNL projector and let it stand for at least one hour ever 24 hours.
• An average use of four to five hours per day will ensure longer lamp life.
• Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
• Set the Brightness Mode to low.
• Learn more with Top tips for extending DLP projector lamp life

The post 3 steps to a new Epson G5200 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

It’s important that you buy an authentic Epson G5200WNL projector lamp from a recognized dealer who proudly displays the seal of approval.

Avoid hassles! Go with authentic lamps!

The market has been flooded with copycat counterfeit lamps claiming to be compatible with your Epson  G5200WNL projector.

Unfortunately that is false advertising since these generic lamps can harm the sensitive optics in your projector. They actually have a shorter lamp life and are prone to explosions. Probably the most disturbing thing about generic lamps bought off the Internet is the health hazards they pose. They’ve been created with toxic substitutes but also don’t have the safety guards in place to protect your eyesight from damage. Protect yourself and buy authentic.

Know when to replace the Epson ELPLP46 lamp

The life span of the Epson ELPLP46 is 2000 hours when the Brightness Control is set to High (which is the default) or 3000 hours if the Brightness Control is set to Low. To track the life of your lamp check the number of hours it’s been in use:

• Press the MENU button on either the remote control or on the projector’s control panel.
• Scroll down to INFO to show the number of hours.
• You can see the number of hours left on both High and Low Brightness.

To reset the lamp Brightness:

• Press the MENU button on either the remote control or on the projector’s control panel.
• Scroll down to SETTINGS menu. Press ENTER.
• Scroll down to highlight BRIGHTNESS CONTROL. Press ENTER.
• Press the arrow key to change from High to Low.
• Press ENTER to save the change.

End of life warning signs

When the Epson ELPLP46 is approaching end of life you’ll start to see warnings signs:

• A screen that is gradually dimming or deteriorating.
• Colour in the image appears dark or off colour.
• “Replace the lamp” warning flashing on screen.
• Lamp light flashing a steady orange.

Replace the Epson ELPLP46 lamp immediately so you don’t run the risk of having the lamp explode.

Replacing the Epson ELPLP46 lamp

Before installation follow these important safety tips:

• Turn power button off and after the Epson G5200WNL has beeped twice unplug the power cord.
• The Epson G5200WNL should be cool to the touch. DO NOT attempt to change the Epson ELPLP46 if the projector is still hot. You can be badly burned if you don’t wait for the projector to cool.

IMPORTANT: Do not operate the projectors the lamps is removed as this may result in malfunctions, fire hazard and other accidents.

• Loosen the screws on the Epson G5200WNL projector using the screw drive provided.
• NOTE: Even when the lamp cover is removed in remains attached to the projector to prevent it from falling should the projector be mounted to the ceiling.

• Loosen the two screws holding the Epson ELPLP46 lamp in place. Theses screws also don’t completely come out.

• Grab the handle in the middle of the Epson ELPLP46 and slowly pull out the lamp. Don’t use excessive force or the lamp could break.
• Read this article about what to do if lamp breaks inside the projector.
• NOTE: The Epson ELPLP46 lamp contains mercury and needs to be properly recycled. Don’t thrown the used lamp into your regular garbage.

• Gently insert the new Epson ELPLP46 lamp into the Epson G5200WNL projector.
• Avoid touching the actual lamp since your fingerprints will cause black out spots to appear when the projector starts working.
• Tighten the screws on the Epson ELPLP46 lamp. Be sure not to tighten too much or the lamp may not work.
• Replace the lamp cover and tighten the screw on the Epson ELPLP46 projector lamp cover. You are now ready to reset the lamp timer.

Resetting the Epson G5200WNL Lamp Timer

The Epson G5200WNL has a lamp timer that tracks the number of hours left for the Epson ELPLP46. Every time you install a new Epson ELPLP46 lamp you must reset the lamp timer to zero. Don’t use the Epson ELPLP46 lamp beyond its recommended usage as this can damage the Epson G5200WNL projector.

• Press the MENU button on either the remote control or on the projector’s control panel.
• Scroll down to the RESET option. Press Enter to bring up the reset screen.
• Scroll down to RESET LAMP HOURS.
• A second prompt screen will appear asking for confirmation. Scroll over to the YES option. Press ENTER.
• Press MENU to exit.

Extending the life of your Epson ELPLP46 lamp

Follow this simple tips to make your Epson ELPLP46 lamp last even longer:

• Keep your air filters clean to avoid overheating the projector.
• Turn off the Epson G5200WNL projector and let it stand for at least one hour ever 24 hours.
• An average use of four to five hours per day will ensure longer lamp life.
• Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
• Set the Brightness Mode to low.
• Learn more with Top tips for extending DLP projector lamp life

The post How to intall an Epson G5200WNL projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Save on the technician’s fee. Use this guide to install a new Epson EB-G5300 projector lamp. Your replacement lamp is Epson ELPLP46.

Be prepared with an authentic lamp

It’s critical to install a genuine Epson EB-G5300 projector lamp rather than a counterfeit lamps.

Generic lamps look appealing because of their low cost but have several major flaws:

• generics have shorter lamp life and will not last the full 3000 hours
• knock off lamps have been created with carcinogenic parts including Krypton-85
• generic lamps are prone to explosions
• copycat lamps can damage the sensitive electronics in your Epson PowerLite 830p projector
• no guarantee or refunds offered with generic lamps
• your Epson EB-G5300 warranty will become void

Look for the seal of approval before purchasing your Epson EB-G5300 projector lamp. Read more about the 7 Ways to Spot a Counterfeit Lamp.

End of life warning signs

When the Epson EB-G5300 projector lamp is approaching end of life you’ll start to see warnings signs:

• A screen that is gradually dimming or deteriorating.
• Colour in the image appears dark or off colour.
• “Replace the lamp” warning flashing on screen.
• Lamp light flashing a steady orange.

Replace the Epson ELPLP46 lamp immediately so you don’t run the risk of having the lamp explode.

 Tracking Epson ELPLP46 lamp hours

The life span of the Epson ELPLP46 is 2000 hours when Brightness Control is set to High (which is the default) or 3000 hours if the Brightness Control is set to Low. To track the life of your lamp check the number of hours it’s been in use:

• Press the MENU button on either the remote control or on the projector’s control panel.
• Scroll down to INFO to show the number of hours.
• You can see the number of hours left on both High and Low Brightness.

To reset the lamp Brightness:

• Press the MENU button on either the remote control or on the projector’s control panel.
• Scroll down to SETTINGS menu. Press ENTER.
• Scroll down to highlight BRIGHTNESS CONTROL. Press ENTER.
• Press the arrow key to change from High to Low.
• Press ENTER to save the change.

Installing a new Epson ELPLP46 lamp

Before installation follow these important safety tips:

• Turn power button off and after the Epson EB-G5300 has beeped twice unplug the power cord.
• The Epson PowerLite EB-G5300 should be cool to the touch. DO NOT attempt to change the Epson ELPLP46 if the projector is still hot. You can be badly burned if you don’t wait for the projector to cool.

IMPORTANT: Do not operate the projectors the lamps is removed as this may result in malfunctions, fire hazard and other accidents.

• Loosen the screws on the Epson EB-G5300 projector using the screw drive provided.
• NOTE: Even when the lamp cover is removed in remains attached to the projector to prevent it from falling should the projector be mounted to the ceiling.

• Loosen the two screws holding the Epson ELPLP46 lamp in place. These screws also don’t completely come out.

• Grab the handle in the middle of the Epson ELPLP46 and slowly pull out the lamp.
• Don’t use excessive force or the lamp could break.
• Read this article about what to do if lamp breaks inside the projector.

NOTE: The Epson ELPLP46 lamp contains mercury and needs to be properly recycled. Don’t thrown the used lamp into your regular garbage.

• Gently insert the new Epson ELPLP46 lamp into the Epson EB-G5300 projector.
• Avoid touching the actual lamp since your fingerprints will cause black out spots to appear when the projector starts working.

• Tighten the screws on the Epson ELPLP46 lamp. Be sure not to tighten too much or the lamp may not work.

• Replace the lamp cover and tighten the screw on the Epson ELPLP46 projector lamp cover.

You are now ready to reset the lamp timer.

Resetting the Epson EB-G5300 Lamp Timer

The Epson EB-G5300 has a lamp timer that tracks the number of hours left for the Epson ELPLP46. Every time you install a new Epson ELPLP46 lamp you must reset the lamp timer to zero. Don’t use the Epson ELPLP46 lamp beyond its recommended usage as this can damage the Epson EB-G5300 projector.

• Press the MENU button on either the remote control or on the projector’s control panel.
• Scroll down to the RESET option. Press Enter to bring up the reset screen.
• Scroll down to RESET LAMP HOURS.
• A second prompt screen will appear asking for confirmation. Scroll over to the YES option. Press ENTER.
• Press MENU to exit.

Extending the life of your Epson ELPLP46 lamp

Follow this simple tips to make your Epson ELPLP46 lamp last even longer:

• Keep your air filters clean to avoid overheating the projector.
• Turn off the Epson EB-G5300 projector and let it stand for at least one hour ever 24 hours.
• An average use of four to five hours per day will ensure longer lamp life.
• Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
• Set the Brightness Mode to low.
• Learn more with Top tips for extending DLP projector lamp life

The post Install a new Epson EB-G5300 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Be sure to install an authentic Epson PowerLite Pro G5350NL projector lamp and follow this guide for easy replament.

STEP 1: When do I need to change the lamp?

When the Epson PowerLite Pro G5350NL projector lamp is approaching end of life you’ll start to see warnings signs:

• A screen that is gradually dimming or deteriorating.
• Colour in the image appears dark or off colour.
• “Replace the lamp” warning flashing on screen.
• Lamp light flashing a steady orange.

Replace the Epson PowerLite Pro G5350NL projector lamp immediately so you don’t run the risk of having the lamp explode.

Tracking lamp life

The life span of the Epson ELPLP46 is 2000 hours when Brightness Control is set to High (which is the default) or 3000 hours if the Brightness Control is set to Low. To track the life of your lamp check the number of hours it’s been in use:

• Press the MENU button on either the remote control or on the projector’s control panel.
• Scroll down to INFO to show the number of hours.
• You can see the number of hours left on both High and Low Brightness.

To reset the lamp Brightness:

• Press the MENU button on either the remote control or on the projector’s control panel.
• Scroll down to SETTINGS menu. Press ENTER.
• Scroll down to highlight BRIGHTNESS CONTROL. Press ENTER.
• Press the arrow key to change from High to Low.
• Press ENTER to save the change.

 STEP 2: Be ready with an authentic lamp

What’s the difference between an authentic Epson PowerLite Pro G5350NL projector lamp and a counterfeit version? Quality, price and reliability!

With their bargain prices and easy availability, generic lamps can be a real temptation. However, generic lamps are plagued with problems that may them a poor choice despite the great price tag. The main reason to avoid these so-called compataible, generic lamps include:

• inferior workmanship means a inferior product
• unable to be calibrated properly they can seriously damage the optics in your Epson PowerLite Pro G5350NL.
  
• don’t last the full 2000 hours.
• present a serious health hazard due to their toxic materials.
• void the warranty on your Epson PowerLite Pro G5350NL projector.

Buy an authentic lamp from a recognized dealer who proudly displays the seal of approval. Protect yourself and buy authentic.

STEP 3: Replacing the Epson PowerLite Pro G5350NL projector lamp

Before installation follow these important safety tips:

• Turn power button off and after the Epson PowerLite Pro G5350NL has beeped twice unplug the power cord.
• The Epson PowerLite Pro G5350NL should be cool to the touch. DO NOT attempt to change the Epson ELPLP46 if the projector is still hot. You can be badly burned if you don’t wait for the projector to cool.

IMPORTANT: Do not operate the projectors the lamps is removed as this may result in malfunctions, fire hazard and other accidents.

• Loosen the screws on the Epson PowerLite G5350NL projector using the screw drive provided.
• NOTE: Even when the lamp cover is removed in remains attached to the projector to prevent it from falling should the projector be mounted to the ceiling.

• Loosen the two screws holding the Epson ELPLP46 lamp in place. Theses screws also don’t completely come out.

• Grab the handle in the middle of the Epson ELPLP46 and slowly pull out the lamp.
• Don’t use excessive force or the lamp could break.
• Read this article about what to do if lamp breaks inside the projector.

• Gently insert the new Epson ELPLP46 lamp into the Epson PowerLite G5350NL projector.
• Avoid touching the actual lamp since your fingerprints will cause black out spots to appear when the projector starts working.
• Tighten the screws on the Epson ELPLP46 lamp. Be sure not to tighten too much or the lamp may not work.
• Replace the lamp cover and tighten the screw on the Epson ELPLP46 projector lamp cover.

NOTE: The Epson ELPLP46 lamp contains mercury and needs to be properly recycled. Don’t throw the used lamp into your regular garbage.

You are now ready to reset the lamp timer.

Resetting the Epson PowerLite Pro G5350NL Lamp Timer

The PowerLite Pro G5350NL has a lamp timer that tracks the number of hours left for the Epson ELPLP46. Every time you install a new Epson ELPLP46 lamp you must reset the lamp timer to zero. Don’t use the Epson ELPLP46 lamp beyond its recommended usage as this can damage the Epson Pro G5350NL projector.

• Press the MENU button on either the remote control or on the projector’s control panel.
• Scroll down to the RESET option. Press Enter to bring up the reset screen.
• Scroll down to RESET LAMP HOURS.
• A second prompt screen will appear asking for confirmation. Scroll over to the YES option. Press ENTER.
• Press MENU to exit.

Extending the life of your Epson PowerLite Pro G5350NL projector lamp

Follow this simple tips to make your Epson ELPLP46 lamp last even longer:

• Keep your air filters clean to avoid overheating the projector.
• Turn off the PowerLite Pro G5350NL projector and let it stand for at least one hour ever 24 hours.
• An average use of four to five hours per day will ensure longer lamp life.
• Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
• Set the Brightness Mode to low.
• Learn more with Top tips for extending DLP projector lamp life

The post 3 steps to a new Epson PowerLite Pro G5350NL projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

It’s important that you buy an authentic Epson PowerLite Pro G5200WNL projector lamp from a recognized dealer who proudly displays the seal of approval.  The market has been flooded with copycat counterfeit lamps claiming to be compatible with your Epson PowerLite Pro G5200WNL projector. Unfortunately that is false advertising since these generic lamps can harm the sensitive optics in your projector. They actually have a shorter lamp life and are prone to explosions.  Probably the most disturbing thing about generic lamps bought off the Internet is the health hazards they pose. They’ve been created with toxic substitutes but also don’t have the safety guards in place to protect your eyesight from damage. Protect yourself and buy authentic.

Tracking lamp life

The life span of the Epson PowerLite Pro G5200WNL projector lamp is 2000 hours when the Brightness Control is set to High (which is the default) or 3000 hours if the Brightness Control is set to Low. To track the life of your lamp check the number of hours it’s been in use:

• Press the MENU button on either the remote control or on the projector’s control panel.
• Scroll down to INFO to show the number of hours.
• You can see the number of hours left on both High and Low Brightness.

To reset the lamp Brightness:

• Press the MENU button on either the remote control or on the projector’s control panel.
• Scroll down to SETTINGS menu. Press ENTER.
• Scroll down to highlight BRIGHTNESS CONTROL. Press ENTER.
• Press the arrow key to change from High to Low.
• Press ENTER to save the change.

End of life warning signs

When the Epson PowerLite Pro G5200WNL projector lamp is approaching end of life you’ll start to see warnings signs:

• A screen that is gradually dimming or deteriorating.
• Colour in the image appears dark or off colour.
• “Replace the lamp” warning flashing on screen.
• Lamp light flashing a steady orange.

Replace the Epson ELPLP46 lamp immediately so you don’t run the risk of having the lamp explode.

Replacing the Epson PowerLite Pro G5200WNL projector lamp

Before installation follow these important safety tips:

• Turn power button off and after the Epson PowerLite Pro G5200WNL has beeped twice unplug the power cord.
• The Epson PowerLite Pro G5200WNL should be cool to the touch. DO NOT attempt to change the Epson ELPLP46 if the projector is still hot. You can be badly burned if you don’t wait for the projector to cool.

IMPORTANT: Do not operate the projectors the lamps is removed as this may result in malfunctions, fire hazard and other accidents.

• Loosen the screws on the Epson PowerLite Pro G5200WNL projector using the screw drive provided.
• NOTE: Even when the lamp cover is removed in remains attached to the projector to prevent it from falling should the projector be mounted to the ceiling.

• Loosen the two screws holding the Epson ELPLP46 lamp in place. Theses screws also don’t completely come out.

• Grab the handle in the middle of the Epson ELPLP46 and slowly pull out the lamp. Don’t use excessive force or the lamp could break.
• Read this article about what to do if lamp breaks inside the projector.
• NOTE: The Epson ELPLP46 lamp contains mercury and needs to be properly recycled. Don’t throw the used lamp into your regular garbage.

• Gently insert the new Epson ELPLP46 lamp into the Epson PowerLite Pro G5200WNL projector.
• Avoid touching the actual lamp since your fingerprints will cause black out spots to appear when the projector starts working.
• Tighten the screws on the Epson ELPLP46 lamp. Be sure not to tighten too much or the lamp may not work.
• Replace the lamp cover and tighten the screw on the Epson ELPLP46 projector lamp cover.

You are now ready to reset the lamp timer.

Resetting the Epson PowerLite Pro G5200WNL Lamp Timer

The PowerLite Pro G5200WNL has a lamp timer that tracks the number of hours left for the Epson ELPLP46. Every time you install a new Epson ELPLP46 lamp you must reset the lamp timer to zero. Don’t use the Epson ELPLP46 lamp beyond its recommended usage as this can damage the Epson Pro G5200WNL projector.

• Press the MENU button on either the remote control or on the projector’s control panel.
• Scroll down to the RESET option. Press Enter to bring up the reset screen.
• Scroll down to RESET LAMP HOURS.
• A second prompt screen will appear asking for confirmation. Scroll over to the YES option. Press ENTER.
• Press MENU to exit.

Extending the life of your Epson ELPLP46 lamp

Follow this simple tips to make your Epson ELPLP46 lamp last even longer:

• Keep your air filters clean to avoid overheating the projector.
• Turn off the PowerLite Pro G5200WNL projector and let it stand for at least one hour ever 24 hours.
• An average use of four to five hours per day will ensure longer lamp life.
• Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
• Set the Brightness Mode to low.
• Learn more with Top tips for extending DLP projector lamp life

The post Replaceming the Epson PowerLite Pro G5200WNL projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.