Go with OEM authentic lamps

When the Optoma DX608 projector lamp has reached end of life, the Lamp Replacement message will appear on screen. You should prepare to change the lamp as you 30 hours or less before the projector shuts down. Be sure to buy an authentic an Optoma DX608 projector lamp for the Optoma DX608 projector.

Why avoid generics:

• generic lamps have a much shorter life so are actually more expensive in the long run
• Krypton-85 and other toxic chemicals are used to create counterfeit lamps
• compatible lamps are more prone to overheat and explode
• copycat manufacturers don’t know how to properly calibrate their lamps to work with the sensitive electronics in projectors
• copycat manufacturers offer no guarantee or refunds
• the warranty on your Optoma DX608 projector will become void.

Learn the 7 Ways to Spot a Counterfeit Lamp.

FP230A lamp

Learn how to install the Optoma BL-FP230A lamp into your compatible Optoma projector.

Before purchasing look for the seal of approval that lets you know you are buying from an authentic manufacturer.

Find this lamp on Amazon from these authorize dealers:

• Optoma BL-FP230A LCD Projector Brand New High Quality Original Projector Bulb
• Optoma BL-FP230A, P-VIP, 230W Projector Lamp (Discontinued by Manufacturer)

Step-by-step instructions

Your Optoma DX608 projector lamp needs a Optoma BL-FP230A lamp. Follow these safety tip before installing a new lamp:

• Switch off the power to the Optoma DX608 projector by pressing the Power/Standby button.
• Disconnect the power cord.
• Allow the projector to cool down for at least 30 minutes. If should be cool to the touch. These projectors run using high temperatures and you can burn yourself badly if you don’t allow the projector to cool down.

Using a screwdriver, remove the screw holding the cover in place.

Push the cover up to remove.

Use a screwdriver to remove the two screws holding the lamp module in place.

Slowly put out the old lamp by grabbing the edge of the lamp. Be careful not to bang the lamp against the projector as this may case the bulb to break. Learn what to do if the lamp has exploded inside the projector. Note: The used Optoma BL-FP230A lamp contains mercury and should be properly recycled.

Place the new Optoma BL-FP230A lamp into the Optoma DX608 projector. Tighten the two screws on the lamp. Replace the lamp cover and tighten its two screws.

You must now reset the Lamp Replacement Timer.

Reset the lamp timing on the Optoma DX608

The Optoma DX608 projector has an automatic lamp reset timer that tracks the life of the lamp and triggers the lamp replacement warning. You need to reset the timer each time the lamp is replaced.

• Press the Menu option on either the remote or on the projector.
• Scroll over the Lamp Setting. Press Enter.
• Select Reset Lamp Hours. Press Enter
• The Execute/Cancel command line will appear.
• Scroll over to choose Execute. Press Enter.
• The lamp hours will be reset to zero.

Extend the life of the Optoma BL-FP230A lamp:

• Turning on the Eco Mode to lower power consumption and extend the lamp life by 130%.
• Keep your air filters clean to avoid overheating the projector.
• Turn off the Optoma DX608 projector and let it stand for at least one hour ever 24 hours.
• Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
• Learn more with Top tips for extending DLP projector lamp life.

The post How to replace the Optoma DX608 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Step 1: Let’s discuss generics

Your Optoma EP7477 needs an Optoma BL-FP230A (SP.83R01G001)  lamp. There are lots of choices out there on the Internet but since selling online has few regulations, it’s easy to get duped into buying an inferior knock-off . Invest in an authentic Optoma EP7477 projector lamp.

Counterfeit manufacturers advertise their lamp as “compatible but there’s nothing farther from the truth.

Why avoid generics:

• generic lamps have a much shorter life so are actually more expensive in the long run
• Krypton-85 and other toxic chemicals are used to create counterfeit lamps
• compatible lamps are more prone to overheat and explode
• copycat manufacturers don’t know how to properly calibrate their lamps to work with the sensitive electronics in projectors
• copycat manufacturers offer no guarantee or refunds
• the warranty on your Optoma EP747a projector will become void.

Learn how to spot the copycat fake lamps with 7 Ways to Spot a Counterfeit Lamp.

Find this lamp on Amazon from these authorize dealers:

• Optoma BL-FP230A LCD Projector Brand New High Quality Original Projector Bulb
• Optoma BL-FP230A, P-VIP, 230W Projector Lamp (Discontinued by Manufacturer)

Step 2: The warning signs

At 3o hours as the Optoma BL-FP230A lamp approaches end of life, a Lamp Replacement message will appear on screen.  If you hear a loud popping sound, the lamp has burnt out and needs to be replaced immediately. The projector will not turn back on until the lamp has been replaced. Replace ASAP!

Step 3: Replacing the Optoma BL-FP230A lamp

Be sure to buy an authentic an Optoma BL-FP230A for the Optoma EP7477 projector.

NOTE: The Optoma BL-FP230A  lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps! If you bought from an authentic manufacturer they will recycle the lamp for you at no extra cost. Generic manufacturers don’t recycle.

Follow these step-by-step instructions to replace the Optoma BL-FP230A lamp:

• Switch off the power to the Optoma EP7477 projector by pressing the Power/Standby button.
• Allow the projector to cool down for at least 30 minutes. If should be cool to the touch. These projectors run using high temperatures and you can burn yourself badly if you don’t allow the projector to cool down.
• Disconnect the power cord.
• Using a screwdriver, remove the screws holding the cover in place.
• Push the cover up to remove.

Use a screwdriver to remove the two screws holding the lamp module in place.

Slowly put out the old lamp by grabbing the edge of the lamp. Be careful not to bang the lamp against the projector as this may case the bulb to break. Learn what to do if the lamp has exploded inside the projector.

Be sure to properly recycle the used Optoma BL-FP230A lamp!

Place the new  BL-FP230A  into the Optoma EP7477 projector. Tighten the two screws on the lamp. Replace the lamp cover and tighten its two screws.

You must now reset the Lamp Replacement Timer.

Reset the lamp timing on the Optoma EP7477

• Press the Menu option on either the remote or on the projector.
• Scroll over the Lamp Setting. Press enter.
• Select Reset Lamp Hours. Press Enter
• The Execute/Cancel command line will appear.
• Scroll over to choose Execute. Press Enter.
• The lamp hours will be reset to zero.

Turn on the Eco Mode to lower power consumption and extend the lamp life by 130%.

Learn the TOP Tips for extending the lamp life in your Optoma EP7477 projector.

The post Replace the Optoma EP7477 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

At 3o hours, when the Optoma EP747T projector lamp is reaching end of life, you will see the Lamp Replacement message on your screen.

Be sure to buy authentic lamps and avoid generic lamps. Optoma EP747T projector lamp generic lamps may appear to be a bargain but actually less durable than authentic lamp.

Find this lamp from the following OEM manufacturers on Amazon:

• Optoma BL-FP230H, P-VIP, 230W Projector Lamp
• Optoma Projector Lamp Part BL-FP230H-ER Model Optoma GT GT750 GT GT750-XL GT GT750E
•  SP.8MY01GC01 / BL-FP230H- Lamp With Housing For Optoma GT750, GT750E, GT750-XL Projectors
• Optoma BL-FP230H Projector Brand New High Quality Original Projector Bulb.
  

Replace the Optoma EP747T projector lamp

NOTE: The Optoma BL-FP230A lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps! If you bought from an authentic manufacturer they will recycle the lamp for you at no extra cost. Generic manufacturers don’t recycle.

Step 1

• Switch off the power to the Optoma EP747T projector by pressing the Power/Standby button.

• Allow the projector to cool down for at least 30 minutes. If should be cool to the touch. These projectors run using high temperatures and you can burn yourself badly if you don’t allow the projector to cool down.
• Disconnect the power cord. Using a screwdriver, remove the screws holding the cover in place. Push the cover up to remove.

Step 2

• Use a screwdriver to remove the two screws holding the Optoma EP747T lamp module in place.
• Slowly put out the old lamp by grabbing the edge of the lamp. Be careful not to bang the lamp against the projector as this may case the bulb to break. Learn what to do if the lamp has exploded inside the projector.

Step 3

• Place the new Optoma BL-FP230A (SP.83R01G001) into the Optoma EP747T projector. Tighten the two screws on the lamp. Replace the lamp cover and tighten its two screws.
• You must now reset the Lamp Replacement Timer.

Reset the lamp timing on the Optoma EP747T

• Press the Menu option on either the remote or on the projector.
• Scroll over the Lamp Setting. Press enter.
• Select Reset Lamp Hours. Press Enter
• The Execute/Cancel command line will appear.
• Scroll over to choose Execute. Press Enter.
• The lamp hours will be reset to zero.

Turn on the Eco Mode to lower power consumption and extend the lamp life by 130%.

Why buy authentic lamps?

There are lots of choices out there on the Internet. Since selling online has few regulations, it’s easy to get duped into buying an inferior knock-off lamp posing as an authentic Optoma BL-FP230A.

The tell tale sign is a price that seems too good to be true. These counterfeit manufacturers will advertise their lamp as “compatible.” However, it’s anything but compatible.

Learn how to spot the copycat fake lamps with 7 Ways to Spot a Counterfeit Lamp.

6 reasons to avoid generics:

• generic lamps have a much shorter life so are actually more expensive in the long run
• Krypton-85 and other toxic chemicals are used to create counterfeit lamps
• compatible lamps are more prone to overheat and explode
• copycat manufacturers don’t know how to properly calibrate their lamps to work with the sensitive electronics in projectors
• copycat manufacturers offer no guarantee or refunds
• the warranty on your Optoma EP747T projector will become void.

The post Replacement guide for Optoma EP747T projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

If you’ve seen the replacement warning for the Optoma EP747N projector lamp, keep reading! Our step-by-step guides will show you how to replace the lamp in three easy steps.

Your Optoma EP747N uses a Optoma BL-FP230A lamp.  Be sure to buy authentic lamp and keep your projector working as its best. Generic are not worth the trouble even if they are less expensive!

Find this lamp from the following OEM manufacturers on Amazon:

• Optoma BL-FP230H, P-VIP, 230W Projector Lamp
• Optoma Projector Lamp Part BL-FP230H-ER Model Optoma GT GT750 GT GT750-XL GT GT750E
•  SP.8MY01GC01 / BL-FP230H- Lamp With Housing For Optoma GT750, GT750E, GT750-XL Projectors
• Optoma BL-FP230H Projector Brand New High Quality Original Projector Bulb.
  

6 reasons to avoid generics:

• generic lamps have a much shorter life so are actually more expensive in the long run
• Krypton-85 and other toxic chemicals are used to create counterfeit lamps
• compatible lamps are more prone to overheat and explode
• copycat manufacturers don’t know how to properly calibrate their lamps to work with the sensitive electronics in projectors
• copycat manufacturers offer no guarantee or refunds
• the warranty on your Optoma EP747H projector will become void.

Replace the Optoma EP747H projector lamp

When the Optoma BL-FP230A lamp is reaching end of life, you will see the Lamp Replacement message. You have 30 hours or less before the projector shuts down.

Step 1

• Switch off the power to the Optoma EP747H projector by pressing the Power/Standby button.

• Allow the projector to cool down for at least 30 minutes. If should be cool to the touch. These projectors run using high temperatures and you can burn yourself badly if you don’t allow the projector to cool down.
• Disconnect the power cord. Using a screwdriver, remove the screws holding the cover in place.Push the cover up to remove.

Step 2

• Use a screwdriver to remove the two screws holding the lamp module in place.
• Slowly put out the old lamp by grabbing the edge of the lamp. Be careful not to bang the lamp against the projector as this may case the bulb to break. Learn what to do if the lamp has exploded inside the projector.
• Note: The used Optoma BL-FP230A lamp contains mercury and should not be thrown out with regular garbage and should be recycled.

Step 3

• Place the new Optoma BL-FP230A into the Optoma EP747N projector. Tighten the two screws on the lamp. Replace the lamp cover and tighten its two screws.
• You must now reset the Lamp Replacement Timer.

Reset the lamp timing on the Optoma EP747N

• Press the Menu option on either the remote or on the projector.
• Scroll over the Lamp Setting. Press enter.
• Select Reset Lamp Hours. Press Enter
• The Execute/Cancel command line will appear.
• Scroll over to choose Execute. Press Enter.
• The lamp hours will be reset to zero.

Turn on the Eco Mode to lower power consumption and extend the lamp life by 130%.

Why buy authentic lamps?

There are lots of choices out there on the Internet. Since selling online has few regulations, it’s easy to get duped into buying an inferior knock-off lamp posing as an authentic Optoma BL-FP230A.

The tell tale sign is a price that seems too good to be true. These counterfeit manufacturers will advertise their lamp as “compatible.” However, it’s anything but compatible.

Learn how to spot the copycat fake lamps with 7 Ways to Spot a Counterfeit Lamp.

The post How to replace the Optoma EP747N projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Wondering when to replace the Optoma EP705H projector lamp? Just follow our quick guide. When the Optoma BL-FU150A lamp is reaching end of life, you will see the Lamp Replacement message. You have 30 hours or less before the projector shuts down. Be sure to buy an authentic an Optoma EP705H projector lamp.

Buy this lamp on Amazon from the following authorized dealers:

• Optoma BL-FU150A LCD Projector Brand New High Quality Original Projector Bulb
  

Replace the Optoma EP705H projector lamp

NOTE: The Optoma BL-FU150A lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

Step 1:

• Switch off the power to the Optoma EP705H projector.
• Allow the projector to cool down for at least 30 minutes or until it is cool to the touch. These projectors run using high temperatures and you can burn yourself badly if you don’t allow the projector to cool down.Disconnect the power cord.
• Using a screwdriver, remove the screw holding the cover in place.
• Remove the cover from the Optoma EP705H projector.

 Step 2:

On the left side of the lamp module, push the electrical connector up to disengage it from the projector base.

Step 3:

• Loosen the three screw holding the Optoma BL-FU150A lamp into the Optoma EP705H.
• Remove the three screws from the lamp module.

Step 4:

• Pull out the lamp manually.
• Gently slide in the new BL-FU150A (SP.82902.001). Take care not to touch the actual bulb as this may cause black spots to appear when the oil from your fingerprint heats up.
• Tighten the two screws on the lamp.
• Replace the lamp cover and tighten its two screws.

You must now reset the Lamp Replacement Timer.

Reset the lamp timing on the Optoma EP705H

• Press the Menu option on either the remote or on the projector.
• Scroll over the Lamp Setting. Press enter.
• Select Reset Lamp Hours. Press Enter
• The Execute/Cancel command line will appear.
• Scroll over to choose Execute. Press Enter.
• The lamp hours will be reset to zero.

Turn on the Eco Mode to lower power consumption and extend the lamp life by 130%.

Why buy authentic lamps?

There are lots of choices out there on the Internet. Since selling online has few regulations, it’s easy to get duped into buying an inferior knock-off lamp posing as an authentic Optoma EP705H.

The tell tale sign is a price that seems too good to be true. These counterfeit manufacturers will advertise their lamp as “compatible.” However, it’s anything but compatible.

Why avoid generics:

• generic lamps have a much shorter life so are actually more expensive in the long run
• Krypton-85 and other toxic chemicals are used to create counterfeit lamps
• compatible lamps are more prone to overheat and explode
• copycat manufacturers don’t know how to properly calibrate their lamps to work with the sensitive electronics in projectors
• copycat manufacturers offer no guarantee or refunds
• the warranty on your Optoma EP705H projector will become void.

Learn how to spot the copycat fake lamps with 7 Ways to Spot a Counterfeit Lamp.

The post Replacing the Optoma EP705H projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Be sure to buy an authentic an Optoma EP747H projector lamp. Scroll down to learn why authentic lamps are so important for your projector.

At 30 hours, when  the Optoma EP747H projector lamp is reaching end of life, you will see the Lamp Replacement message. Replace immediately!

Find this lamp from the following OEM manufacturers on Amazon:

• Optoma BL-FP230H, P-VIP, 230W Projector Lamp
• Optoma Projector Lamp Part BL-FP230H-ER Model Optoma GT GT750 GT GT750-XL GT GT750E
•  SP.8MY01GC01 / BL-FP230H- Lamp With Housing For Optoma GT750, GT750E, GT750-XL Projectors
• Optoma BL-FP230H Projector Brand New High Quality Original Projector Bulb.
  

Replace the projector lamp

Step 1:

• Switch off the power to the Optoma EP747H projector by pressing the Power/Standby button.
• Allow the projector to cool down for at least 30 minutes. If should be cool to the touch. These projectors run using high temperatures and you can burn yourself badly if you don’t allow the projector to cool down.
• Disconnect the power cord. Using a screwdriver, remove the screws holding the cover in place.

Push the cover up to remove.

 Step 2

• Use a screwdriver to remove the two screws holding the lamp module in place.
• Slowly put out the old lamp by grabbing the edge of the lamp. Be careful not to bang the lamp against the projector as this may case the bulb to break. Learn what to do if the lamp has exploded inside the projector.
• Note: The used Optoma BL-FP230A contains mercury and should not be thrown out with regular garbage and should be recycled.

 Step 3

• Place the new Optoma BL-FP230A (SP.83R01G001) into the Optoma EP747H projector. Tighten the two screws on the lamp. Replace the lamp cover and tighten its two screws.
• You must now reset the Lamp Replacement Timer.

Reset the lamp timing on the Optoma EP747H

• Press the Menu option on either the remote or on the projector.
• Scroll over the Lamp Setting. Press enter.
• Select Reset Lamp Hours. Press Enter
• The Execute/Cancel command line will appear.
• Scroll over to choose Execute. Press Enter.
• The lamp hours will be reset to zero.

Turn on the Eco Mode to lower power consumption and extend the lamp life by 130%.

Why buy authentic lamps?

There are lots of choices out there on the Internet. Since selling online has few regulations, it’s easy to get duped into buying an inferior knock-off lamp posing as an authentic Optoma BL-FP230A.

The tell tale sign is a price that seems too good to be true. These counterfeit manufacturers will advertise their lamp as “compatible.” However, it’s anything but compatible.

Why avoid generics:

• generic lamps have a much shorter life so are actually more expensive in the long run
• Krypton-85 and other toxic chemicals are used to create counterfeit lamps
• compatible lamps are more prone to overheat and explode
• copycat manufacturers don’t know how to properly calibrate their lamps to work with the sensitive electronics in projectors
• copycat manufacturers offer no guarantee or refunds
• the warranty on your Optoma EP747H projector will become void.

Learn how to spot the copycat fake lamps with 7 Ways to Spot a Counterfeit Lamp.

The post 3 Steps to a new Optoma EP747H projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Replacing the Optoma EP7475 projector lamp doesn’t have to be time consuming or difficult. This quick guide will help you install a new Optoma BL-FP230A lamp in less than 15 minutes.

When the Optoma EP7475 projector lamp lamp is reaching end of life, the Lamp Replacement message will appear on screen. You should prepare to change the lamp as you 30 hours or less Fbefore the projector shuts down.

Be prepared, buy authentic

Be sure to buy an authentic an Optoma BL-FP230A lamp for the Optoma EP7475 projector. Scroll down for the 6 reasons to avoid generics.

Find this lamp on Amazon from these authorize dealers:

• Optoma BL-FP230A LCD Projector Brand New High Quality Original Projector Bulb
• Optoma BL-FP230A, P-VIP, 230W Projector Lamp (Discontinued by Manufacturer)

Step-by-step instructions

Follow these safety steps before installing the new Optoma BL-FP230A lamp:

• Switch off the power to the Optoma EP7475 projector by pressing the Power/Standby button.
• Disconnect the power cord.
• Allow the projector to cool down for at least 30 minutes. If should be cool to the touch. These projectors run using high temperatures and you can burn yourself badly if you don’t allow the projector to cool down.

Using a screwdriver, remove the screws holding the cover in place.

Push the cover up to remove.

Use a screwdriver to remove the two screws holding the lamp module in place.

Slowly put out the old lamp by grabbing the edge of the lamp. Be careful not to bang the lamp against the projector as this may case the bulb to break. Learn what to do if the lamp has exploded inside the projector.

Note: The used Optoma BL-FP230A lamp contains mercury and should be properly recycled. Don’t throw it into regular garbage.

Place the new BL-FP230A into the Optoma EP7475 projector. Tighten the two screws on the lamp. Replace the lamp cover and tighten its two screws.

You must now reset the Lamp Replacement Timer.

Reset the lamp timing on the Optoma EP7475

The Optoma EP7474 projector has an automatic lamp reset timer that tracks the life of the lamp and triggers the lamp replacement warning. You need to reset the timer each time the lamp is replaced.

• Press the Menu option on either the remote or on the projector.
• Scroll over the Lamp Setting. Press enter.
• Select Reset Lamp Hours. Press Enter
• The Execute/Cancel command line will appear.
• Scroll over to choose Execute. Press Enter.
• The lamp hours will be reset to zero.

Extend the life of the Optoma BL-FP230A (SP.83R01G001) lamp by:

• Turning on the Eco Mode to lower power consumption and extend the lamp life by 130%.
• Keep your air filters clean to avoid overheating the projector.
• Turn off the Optoma EP7475 projector and let it stand for at least one hour ever 24 hours.
• Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
• Learn more with Top tips for extending DLP projector lamp life

6 reason to avoid generics:

• generic lamps have a much shorter life so are actually more expensive in the long run
• Krypton-85 and other toxic chemicals are used to create counterfeit lamps
• compatible lamps are more prone to overheat and explode
• copycat manufacturers don’t know how to properly calibrate their lamps to work with the sensitive electronics in projectors
• copycat manufacturers offer no guarantee or refunds
• the warranty on your Optoma EP7475 projector will become void.

Learn the 7 Ways to Spot a Counterfeit Lamp.

The post How to install a new Optoma EP7475 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Learn how to replace the Optoma EP747a projector lamp.

Our quick guide shows you how to replace the Optoma EP747a projector lamp in three easy steps. The Optoma EP747a uses the Optoma BL-FP230A lamp. When the lamp is reaching end of life, you will see the Lamp Replacement message. You have 30 hours or less before the projector shuts down.  If you hear a loud popping sound, the lamp has burnt out and needs to be replaced immediately. The projector will not turn back on until the lamp has been replaced.

Find this lamp on Amazon from these authorize dealers:

• Optoma BL-FP230A LCD Projector Brand New High Quality Original Projector Bulb
• Optoma BL-FP230A, P-VIP, 230W Projector Lamp (Discontinued by Manufacturer)

To replace the Optoma EP747a projector lamp

Be sure to buy an authentic an Optoma EP747a projector lamp. Keep reading to find out why authentic lamps are so important for your projector.

NOTE: The Optoma BL-FP230A lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps! If you bought from an authentic manufacturer they will recycle the lamp for you at no extra cost. Generic manufacturers don’t recycle.

Follow these step-by-step instructions to replace the Optoma BL-FP230A lamp:

Switch off the power to the Optoma EP747a projector by pressing the Power/Standby button. Allow the projector to cool down for at least 30 minutes. If should be cool to the touch. These projectors run using high temperatures and you can burn yourself badly if you don’t allow the projector to cool down.

Disconnect the power cord. Using a screwdriver, remove the screws holding the cover in place.

Push the cover up to remove.

Use a screwdriver to remove the two screws holding the lamp module in place.

Slowly put out the old lamp by grabbing the edge of the lamp. Be careful not to bang the lamp against the projector as this may case the bulb to break. Learn what to do if the lamp has exploded inside the projector.

Note: The used Optoma BL-FP230A lamp contains mercury and should not be thrown out with regular garbage and should always be recycled properly.

Place the new BL-FP230A into the Optoma EP747a projector. Tighten the two screws on the lamp. Replace the lamp cover and tighten its two screws.

You must now reset the Lamp Replacement Timer.

Reset the lamp timing on the Optoma EP747a

• Press the Menu option on either the remote or on the projector.
• Scroll over the Lamp Setting. Press enter.
• Select Reset Lamp Hours. Press Enter
• The Execute/Cancel command line will appear.
• Scroll over to choose Execute. Press Enter.
• The lamp hours will be reset to zero.

Turn on the Eco Mode to lower power consumption and extend the lamp life by 130%.

Why buy authentic lamps?

There are lots of choices out there on the Internet. Since selling online has few regulations, it’s easy to get duped into buying an inferior knock-off lamp posing as an authentic Optoma BL-FP230A.

The tell tale sign is a price that seems too good to be true. These counterfeit manufacturers will advertise their lamp as “compatible.” However, it’s anything but compatible.

Why avoid generics:

• generic lamps have a much shorter life so are actually more expensive in the long run
• Krypton-85 and other toxic chemicals are used to create counterfeit lamps
• compatible lamps are more prone to overheat and explode
• copycat manufacturers don’t know how to properly calibrate their lamps to work with the sensitive electronics in projectors
• copycat manufacturers offer no guarantee or refunds
• the warranty on your Optoma EP747a projector will become void.

Learn how to spot the copycat fake lamps with 7 Ways to Spot a Counterfeit Lamp.

The post How to install a new Optoma EP747a projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

When the Optoma EP747 projector lamp is reaching end of life, you will see the Lamp Replacement message. You have 30 hours or less before the projector shuts down.

If you hear a loud popping sound, the lamp has burnt out and needs to be replaced immediately. The projector will not turn back on until the lamp has been replaced.

FP230A lamp

Learn how to install the Optoma BL-FP230A lamp into your compatible Optoma projector. Before purchasing look for the seal of approval that lets you know you are buying from an authentic manufacturer.

Find this lamp on Amazon from these authorize dealers:

• Optoma BL-FP230A LCD Projector Brand New High Quality Original Projector Bulb
• Optoma BL-FP230A, P-VIP, 230W Projector Lamp (Discontinued by Manufacturer)

To replace the Optoma BL-FP230A lamp

Be sure to buy an authentic an Optoma BL-FP230A lamp for the Optoma EP747 projector. Keep reading to find out why authentic lamps are so important for your projector.

NOTE: The Optoma BL-FP230A projector lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps! If you bought from an authentic manufacturer they will recycle the lamp for you at no extra cost. Generic manufacturers don’t recycle.

Follow these step-by-step instructions to replace the Optoma BL-FP230A projector lamp:

Switch off the power to the projector by pressing the Power/Standby button. Allow the projector to cool down for at least 30 minutes. If should be cool to the touch. These projectors run using high temperatures and you can burn yourself badly if you don’t allow the projector to cool down.

Disconnect the power cord. Using a screwdriver, remove the screws holding the cover in place. Push the cover up to remove.

Use a screwdriver to remove the two screws holding the lamp module in place.

Slowly put out the old lamp by grabbing the edge of the lamp. Be careful not to bang the lamp against the projector as this may case the bulb to break. Learn what to do if the lamp has exploded inside the projector.

Note: The used Optoma BL-FP230A lamp contains mercury and should not be thrown out with regular garbage. It needs to be properly recycled.

Place the new BL-FP230A (SP.83R01G001) lamp into the Optoma EP747 projector. Tighten the two screws on the lamp. Replace the lamp cover and tighten its two screws.

You must now reset the Lamp Replacement Timer.

Reset the lamp timing on the Optoma EP747

• Press the Menu option on either the remote or on the projector.
• Scroll over the Lamp Setting. Press enter.
• Select Reset Lamp Hours. Press Enter
• The Execute/Cancel command line will appear.
• Scroll over to choose Execute. Press Enter.
• The lamp hours will be reset to zero.

Turn on the Eco Mode to lower power consumption and extend the lamp life by 130%.

Why buy authentic?

There are lots of choices out there on the Internet. Since selling online has few regulations, it’s easy to get duped into buying an inferior knock-off lamp posing as an authentic Optoma BL-FP230A (SP.83R01G001) lamp.

The tell tale sign is a price that seems too good to be true. These counterfeit manufacturers will advertise their lamp as “compatible.” However, it’s anything but compatible.

Why avoid generics:

• generic lamps have a much shorter life so are actually more expensive in the long run
• Krypton-85 and other toxic chemicals are used to create counterfeit lamps
• compatible lamps are more prone to overheat and explode
• copycat manufacturers don’t know how to properly calibrate their lamps to work with the  sensitive electronics in projectors
• copycat manufacturers offer no guarantee or refunds
• the warranty on your Optoma EP747 projector will become void.

Learn how to spot the copycat fake lamps with 7 Ways to Spot a Counterfeit Lamp.

The post Installing a new Optoma EP747 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.