Sanyo PLC-XL20 projector

Signs you need to replace the Sanyo POA-LMP55 (service parts no 610 309 2706) in the Sanyo PLC-XL20 projector:

When you see these signs, change the Sanyo POA-LMP55 (service parts no 610 309 2706) immediately.

Follow our easy 3-step guide to a new Sanyo PLC-XL20 projector lamp.

STEP ONE: Purchase the correct projector lamp

Sanyo POA-LMP55 service part no 610 309 2706

The lifespan of your Sanyo POA-LMP55 (service parts no 610 309 2706) lamp will vary depending on how much the projector is used and if the filters are cleaned regularly.

The best thing you can do to prolong the life of your Sanyo PLC-XL20  and save money is to invest in an original Sanyo POA-LMP55 (610 309 2706) projector lamp. Generic lamps look like a great bargain since they are generally cheaper, however, these knock-off lamps are created with inferior materials. They are susceptible to explosions, have a shorter life span and can damage the precise components in your Sanyo PLC-XL20 projector. Installing a knock-off generic lamp also voids your warranty.

Learn more about spotting dangerous projector lamps by reading our article: 7 tips for spotting counterfeits.

STEP TWO: Install the Sanyo POA-LMP55 lamp

• NOTE: Allow the Sanyo PLC-XL20 projector to thoroughly cool before changing the lamp. Turn off the projector, unplug the AC cord and allow 45 to 60 minutes for the projector to cool. These projectors operate under high heat and there is a possibility of being burned, if the projector is not fully cooled before changing the lamp.
• The lamp cover for the Sanyo PLC-XL20 is at the bottom of the projector. Gently turn projector over and loosen the screw holding the cover in place. Place the cover to one side.
• Inside you’ll find the Sanyo POA-LMP55 (service parts no 610 309 2706) lamp cage. Loosen all three screws holding the lamp cage in place.
• Grab the lamp handle and gently lift the lamp out of its socket. Place to one side. Be sure to dispose of the used lamp through a local recycling program. Don’t throw this lamp into regular garbage as it contains mercury.
• Taking the new Sanyo POA-LMP55 (service parts no 610 309 2706) lamp assembly by the handle place it into the slot. Avoid touching the actual bulb as the oil from your fingers can burn a black spot on the lenses or you can accidentally break the bulb. Don’t force the lamp into place — it should slide into the slot easily.
• Once the lamp is in, tighten all three screws on the Sanyo POA-LMP55 (610 309 2706) lamp assembly. Make sure the screws have been tightened properly or the Sanyo PLC-XL20 projector will not turn on.
• Replace the Lamp Cover and tighten the screw. Re-connect the power cord and turn on the PLC-XL20 projector. If the Sanyo POA-LMP65 (service parts no 610 307 7925) lamp does not turn on after the warm-up period, try re-installing the lamp.
• Reset the Lamp Replacement Counter following the instructions below.

NOTE: Your old  Sanyo POA-LMP55 (service parts no 610 309 2706) lamp should be properly recycled. These lamps contain mercury and can’t be placed into common garbage.

 Looking for another way to save money? Try replacing only the lamp in the Sanyo POA-LMP115. Find out more in our guide.

STEP THREE: Reset the Sanyo PLC-XL20 Lamp Replace Counter

The Lamp Replacement Counter for the  Sanyo PLC-XL20 will track the correct age of your newly installed lamp and trigger the Lamp Replacement Indicator. Failure to reset the counter may result in the projector not tracking the end of life for the Sanyo POA-LMP65 (service part no 610 307 7925) and letting the projector inadvertently use the lamp past its normal life cycle. Your  Sanyo PLC-XL20 may stop working suddenly if the Lamp Replace Counter has not been properly set.

• Press the MENU Button to display the MAIN MENU. Press the POINT LEFT/RIGHT button and scroll right to select SETTING.
• Press the SELECT button to display the SETTING DISPLAY menu.
• Press the POINT DOWN button (a red arrow will appear).
• Move the red arrow to the LAMP AGE and then press the SELECT button.
• The message “Lamp replace counter reset?”  appears. Move the arrow down to YES and press the SELECT button.
• Move the arrow to QUIT and press the SELECT button.

3 tips for extending the life of the Sanyo POA-LMP55 projector lamp

Extend the life of your newly installed Sanyo POA-LMP55 (service parts no 610 309 2706) by following these helpful tips:

• Wait at least five minutes before turning the PLC-XL20 projector off.
• Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
• Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP55 (service parts no 610 309 2706) and prevent the  PLC-XL20 projector from overheating.

The post Replace your Sanyo PLC-XL20 in 3 easy steps appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Sanyo POA-LMP55 service part no 610 309 2706

The Sanyo POA-LMP55 (service part no 610 309 2706) will give you between 1,000 to 3,000 hours of  lamp life before needing to be replaced.   The exact amount of time will vary depending on how much your projector is used and how regularly the air filters are cleaned. (Clogged air filters cause the projector to heat up and this puts stress on the lamp.)

Watch for warning signs that your Sanyo POA-LMP55 (610 309 2706) needs to be replaced immediately:

1. The Lamp Replace Indicator begins to blink yellow.
2. The picture becomes quite dim.
3. The colors displayed look unnatural or are very dull.

Avoid installing any knock-offs lamp since they have much shorter life spans due to their inferior workmanship and materials. They are also prone to explosions and can harm the sensitive components in your projector. Installing a generic projector lamp also voids the warranty on your projector. Walk away from lamps with a price tag that seems too good to be true. The few dollars you save are not worth. Learn the 7 tips for spotting counterfeits lamps and protect yourself from installing a generic lamp.

Scroll down for links to step-by-step instructions on replacing the Sanyo POA-LMP35 (service part no 610 293 2751) lamp for each of these projectors.

Projectors compatible with the Sanyo POA-LMP55 (610 309 2706) projector lamp:

Sanyo PLC-XL20

Sanyo PLC-XU25

Sanyo PLC-XU47 / PLC-XU48

Sanyo PLC-XU50 / PLC-XU55

Sanyo PLC-XU51

Sanyo PLC-XU58

For step-by-step instructions on replacing your Sanyo POA-LMP55 (service part no 610 309 2706) projector lamp, click on your projector listed below:

Sanyo PLC-XL20 projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP55 (service part no 610 309 2706) projector bulb for the Sanyo PLC-XL20 projector.

Sanyo PLC-XU25 projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP55 (service part no 610 309 2706) projector bulb for the Sanyo PLC-XU25 projector.

Sanyo PLC-XU47 projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP55 (service part no 610 309 2706) projector bulb for the Sanyo PLC-XU47 / PLC-XU48 projector.

Sanyo PLC-XU50 projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP55 (service part no 610 309 2706) projector bulb for the Sanyo PLC-XU50 / PLC-XU55 projector.

Sanyo PLC-XU51 projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP55 (service part no 610 309 2706) projector bulb for the Sanyo PLC-XU51 projector.

Sanyo PLC-XU58 projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP55 (service part no 610 309 2706) projector bulb for the Sanyo PLC-XU58 projector.

The post When to replace the Sanyo POA-LMP55 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Sanyo PLC-XU25 projector

STEP-BY-STEP INSTRUCTIONS FOR PLC-XU25 LAMP REPLACEMENT

If your projector Sanyo PLC-XU25 lamp no longer turns on, it needs to be replaced.  If the picture is dim or looks unnatural the Sanyo POA-LMP55 (service part no 610 309 2706) is reaching its end of life.

If the Replace Lamp Indicator light on the front panel is blinking orange, you must replace the Sanyo POA-LMP55 immediately. Follow our simple step-by-step instructions to replace your lamp in the Sanyo PLC-XU25 projector easily.

Sanyo PLC-XU25 warning light

Replace the Sanyo POA-LMP55 (610 309 2706) immediately with a guaranteed authentic lamp. Be sure to verify that your lamp is authentic and buy from an authorized manufacturer.

If the price of the lamp you’re about to buy seems like an incredible bargain, chances are it’s counterfeit and has been created using inferior parts that  can damage the highly sophsticated componenbts in your Sanyo PLC-XU25 projector since it will not fit properly. Buying a knock-off lamp will also void your warranty and should anything happen to the projector you will not be covered.

Before installation

Allow the Sanyo PLC-XU25 projector to thoroughly cool before changing the lamp. Turn off the projector, unplug the AC cord and allow 45 to 60 minutes for the projector to cool. These projectors operate under high heat and there is a possibility of being burned, if the projector is not fully cooled before changing the Sanyo POA-LMP55 (service part no 610 309 2706) lamp.

Replacing the Sanyo POA-LMP55 (610-309-2706) Lamp Assembly

1. Turn off the Sanyo PLC-XU25 projector.
2. The lamp cover for the Sanyo PLC-XU25 projector is located at the bottom of the projector. Gently turn over the projector onto its side and loosen the screw holding the cover in place. Place the cover to one side.
3. Inside you’ll find the Sanyo POA-LMP55 (service part no 610 309 2706) lamp cage. Loosen both screws holding the lamp cage in place. Grab the lamp handle and gently lift the lamp out of its socket. Place to one side. Be sure to dispose of the lamp properly through a local recycling program.
4. Taking the new Sanyo POA-LMP55 (6103092706) lamp cage by the handle—avoid touching the actual bulb a this can break or damage the lamp. Without forcing the lamp, place it into the slot.
5. Once the lamp is in, tighten both screws on the Sanyo POA-LMP55 Lamp Assembly. Make sure the screws have been tightened properly or the Sanyo PLC-XU25 projector will not turn on.
6. Replace the Lamp Cover and tighten the screw. Re-connect the power cord and turn on the Sanyo PLC-XU25 projector. If the Sanyo POA-LMP55 (610-309-2706) lamp does not turn on after the warm-up period, try re-installing the lamp. Reset the Lamp Counter Screen by following the instructions below.

NOTE: Your old  Sanyo POA-LMP55 (service part no 610 309 2706) lamp should be properly recycled. These lamps contain mercury and can’t be placed into common garbage.

RESETTING THE LAMP REPLACE COUNTER  

In order for the projector to properly track the lamp life of your newly installed Sanyo POA-LMP55 (service part no 610 309 2706)you’ll need to reset the Lamp Replace Counter on the Sanyo PLC-XU25. Failure to do so can result in the Replace Lamp Indicator not tracking the lamp life properly.

• Press SELECT (rear click) to have the SETTING DISPLAY screen appear.
• Press the POINT DOWN button and a red arrow shows up on screen.
• Using the POINT UP/DOWN button, select the LAMP PAGE and then press SELECT.
• You’ll see the message “Lamp replace counter reset?“
• Move the arrow to YES and press SELECT.
• OK is shown for confirmation. Press YES and then the SELECT button.
• Move the arrow QUIT and press SELECT to exit the MENU and return to the screen.
• Your newly installed Sanyo POA-LMP55 (service part no 610 309 2706) should last between 1,000 to 2,000 hours depending on usage and maintenance.

EXTEND THE LIFE OF THE POA-LMP55 LAMP

Make your newly installed Sanyo POA-LMP55 (service part no 610 309 2706) last longer:

• Wait at least five minutes before turning the Sanyo PLC-XU25 projector off.
• Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
• Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP55 (service part no 610 309 2706) and prevent the Sanyo PLC-XU25 from overheating.

.

The post Your easy guide for replacing the Sanyo PLC-XU25 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.