Sanyo POA-LMP55 service part no 610 309 2706

The Sanyo POA-LMP55 (service part no 610 309 2706) will give you between 1,000 to 3,000 hours of  lamp life before needing to be replaced.   The exact amount of time will vary depending on how much your projector is used and how regularly the air filters are cleaned. (Clogged air filters cause the projector to heat up and this puts stress on the lamp.)

Watch for warning signs that your Sanyo POA-LMP55 (610 309 2706) needs to be replaced immediately:

1. The Lamp Replace Indicator begins to blink yellow.
2. The picture becomes quite dim.
3. The colors displayed look unnatural or are very dull.

Avoid installing any knock-offs lamp since they have much shorter life spans due to their inferior workmanship and materials. They are also prone to explosions and can harm the sensitive components in your projector. Installing a generic projector lamp also voids the warranty on your projector. Walk away from lamps with a price tag that seems too good to be true. The few dollars you save are not worth. Learn the 7 tips for spotting counterfeits lamps and protect yourself from installing a generic lamp.

Scroll down for links to step-by-step instructions on replacing the Sanyo POA-LMP35 (service part no 610 293 2751) lamp for each of these projectors.

Projectors compatible with the Sanyo POA-LMP55 (610 309 2706) projector lamp:

Sanyo PLC-XL20

Sanyo PLC-XU25

Sanyo PLC-XU47 / PLC-XU48

Sanyo PLC-XU50 / PLC-XU55

Sanyo PLC-XU51

Sanyo PLC-XU58

For step-by-step instructions on replacing your Sanyo POA-LMP55 (service part no 610 309 2706) projector lamp, click on your projector listed below:

Sanyo PLC-XL20 projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP55 (service part no 610 309 2706) projector bulb for the Sanyo PLC-XL20 projector.

Sanyo PLC-XU25 projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP55 (service part no 610 309 2706) projector bulb for the Sanyo PLC-XU25 projector.

Sanyo PLC-XU47 projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP55 (service part no 610 309 2706) projector bulb for the Sanyo PLC-XU47 / PLC-XU48 projector.

Sanyo PLC-XU50 projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP55 (service part no 610 309 2706) projector bulb for the Sanyo PLC-XU50 / PLC-XU55 projector.

Sanyo PLC-XU51 projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP55 (service part no 610 309 2706) projector bulb for the Sanyo PLC-XU51 projector.

Sanyo PLC-XU58 projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP55 (service part no 610 309 2706) projector bulb for the Sanyo PLC-XU58 projector.

The post When to replace the Sanyo POA-LMP55 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Sanyo PLC-XU58 projector

Your Sanyo PLC-XU58 projector has a  Sanyo POA-LMP55 (service part no 610 309 2706) projector lamp that provides the necessary light to transfer the images from the projector to the screen. Your projector can’t work without this lamp so it’s important to know when to replace the  Sanyo POA-LMP55 (service part no 610 309 2706) lamp. There are three indications that the lamp is approaching it’s end of life:

1. The Lamp Replace Indicator located on the top panel begins flashing yellow.
2. The picture begins to dim.
3. The color quality is off and produces strange colors.

Replace the Sanyo POA-LMP55 (service part no 610 309 2706) immediately if you notice any of these tell tale signs.

Protect your projector with originals

Only genuine Sanyo POA-LMP55 (service part no 610 309 2706) lamps should be used in order to keep your projector is good working order. The authentic POA-LMP55 has been manufactured to meet the specifications of the Sanyo PLC-XU58 projector.

Knock-off lamps may seem like a bargain due to their low prices but these counterfeit lamps can damage the sensitive and expensive mechanismsin your Sanyo XU75/PLC-XU78 projector. They are also prone to explosions and actually have a much shorter working life that authentic lamps due to the inferior materials used during their production. Installing a knock-off lamp will also void the guarantee on your Sanyo PLC- XU58 leaving you unprotected should anything happen after installation. Avoid hassles and buy an authentic Sanyo POA-LMP55 (service part no 610 309 2706) projector lamp.

Before installation

Before installation of the Sanyo POA-LMP55 (service part no 610 309 2706) lamp be sure to turn off the projector and unplug the AC cord. The Sanyo PLC-XU58 projector should be cool to the touch before you replace the projector lamp. It usually takes one hour for the projector to fully cool since these projectors operate under high temperatures.

Do not operate the projectors while any of the lamps are removed as this may result in malfunctions,  fire hazard and other accidents.

Installing the Sanyo POA-LMP55 (610 309 2706) lamp

1. The Lamp Cover is located underneath the Sanyo PLC-XU58 projector. Gently turn the projector upside down, protecting the top of the projector. Using a Philips screwdriver loosen the screw holding the cover in place. Put the cover to one side.

2. Remove the two screws on either side of each the Sanyo POA-LMP55 (service part no 610 309 2706) lamp. Grab the handle on the lamp cage and gently pull out the lamp. Place to one side. Be sure to dispose of the used lamp through a local recycling program. Don’t throw this lamp into regular garbage as it contains mercury.

3. Take the new Sanyo POA-LMP55 (610-309-2706) lamp cage by the handle and gently maneuver it into place. Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb when it starts heating up.

4. Once the lamp is in, tighten the screws on the Lamp Assembly.

5. Replace the Lamp Hazard Cover and tighten the screw.

6. Re-connect the power cord and turn on the Sanyo PLC-XU58 projector to reset the Lamp Replace Counter.

NOTE: Your old  Sanyo POA-LMP55 (service part no 610 309 2706) lamp should be properly recycled. These lamps contain mercury and can’t be placed into common garbage.

Resetting the Lamp Replace Counter

NOTE: Reset the Lamp Replace Counter only when the Sanyo POA-LMP55 (service part no 610 309 2706) lamps has been replaced.

• Make sure the Sanyo PLC-XU58 projector on.
• Press the MENU Button to display the MAIN MENU. Press the POINT LEFT/RIGHT button and scroll right to select SETTING.
• Press the SELECT button to display the SETTING DISPLAY menu.
• Press the POINT DOWN button (a red arrow will appear).
• Move the red arrow to the LAMP AGE and then press the SELECT button.
• The message “Lamp replace counter reset?”  appears. Move the arrow down to YES and press the SELECT button.
• Move the arrow to QUIT and press the SELECT button.

3 tips for extending the life of the Sanyo POA-LMP55 projector lamp

Extend the life of your newly installed Sanyo POA-LMP55 (service part no 610 309 2706) by following these helpful tips:

• Wait at least five minutes before turning the Sanyo PLC-XU58 projector off.
• Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
• Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP55 (service part no 610 309 2706) and prevent the Sanyo PLC-XU58 projector from overheating.
• Use the lower brightness option since this reduces the lamp power consumption and extends the lamp life.

The post The easy way to replace your Sanyo PLC-XU58 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Sanyo PLC-XU51 projector

When it’s time to change your projector lamp on either your Sanyo PLC-XU51 projector, you’ll notice a yellow light blinking on the Top Control panel. This is the lamp replacement indicator letting you know it;s to replace your Sanyo POA-LMP55 (service part no 610 309 2706) projector lamp.

It’s important the buy only a genuine POA-LMP55 to replace the old lamp. The price of counterfeit knock-off lamps may be tempting but can cost you more money in the long run. Counterfeit lamps are not manufactured according to Sanyo’s specifications and can damage the sensitive (and expensive) mechanisms in your Sanyo PLC-XU51 projector.

Replacing the Sanyo POA-LMP107 (610 330 4564) lamp

Before installation of the Sanyo POA-LMP55 (service part no 610 309 2706) lamp: Turn off the projector and unplug the AC cord. Allow the Sanyo PLC-XW50/PLC-XW55 projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures.

Caution: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.

1. Underneath the Sanyo PLC-XU51 projector you’ll find the Lamp Hazard cover. Gently turn it upside down protecting the top of the projector. Using a Philips screwdriver loosen the screw holding the cover in place. Put the cover to one side.

2. Remove the two screws on either side of each the Sanyo POA-LMP55 (service part no 610 309 2706) lamp. Grab the handle on the lamp cage and gently pull out the lamp. Place to one side.

3. Take the new Sanyo POA-LMP55 (610-309-2706) lamp cage by the handle and gently maneuver it into place.

4. Avoid touching the glass or the bulb. The lamp should slide in easily – don’t force it. Once the lamp is in, tighten the screws on the Lamp Assembly.

5. Replace the Lamp Hazard Cover and tighten the screw.

6. Re-connect the power cord and turn on the Sanyo PLC-XU51 projector.

Resetting the Lamp Replacement counter on the Sanyo PLC-XU51

Reset the Lamp Replacement Counter only when the Sanyo POA-LMP55 (service part no 610 309 2706) lamps has been replaced.

Do not operate the projectors while any of the lamps are removed as this may result in malfunctions,  fire hazard and other accidents.

• Turn the Sanyo PLC-XU51 projector on.
• Press the Menu option to display the On-Screen Menu.
• Press Point left/right button(s) to move a red frame poster to Setting Menu icon.
• Press Point Down button to move the red frame pointer to Lamp counter reset.
• Press the Select button.
• Another confirmation dialog box appears, select YES.
• The Lamp box will disappear and the Lamp Replace Dialog box appears.
• Select YES to reset Lamp Replace Counter.

NOTE: When you reset the Lamp Replace Counter the Lamp Replace indicator stops lighting.

3 tips for extending the life of the Sanyo POA-LMP55 projector lamp

Extend the life of your newly installed Sanyo POA-LMP55 (service part no 610 309 2706) by following these helpful tips:

• Wait at least five minutes before turning the Sanyo PLC-XU51 projector off.
• Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
• Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP55 (service part no 610 309 2706) and prevent the Sanyo PLC-XU51 projector from overheating.

The post How to replace the Sanyo PLC-XU51 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Follow our quick guide to replace your projector lamp for the Sanyo PLC-XU50 / PLC-XU55 projector.

One of the first indications that your projector lamp is reaching it’s end of life is when the picture looks dim or has unnatural color. Around the same time, the Lamp Replacement Indciator will start flashing yellow. There are three signs that the lamp in your  Order a replacement Sanyo POA-LMP55 (service part no 610 309 2706) immediately.

Be sure to buy a guaranteed authentic lamp from an authorized manufacturer. These genuine lamps are guaranteed to work properly with the sophisticated parts in your projector and keep your warranty intact.

Sanyo PLC-XU50 projector

Beware of inferior lamp knock-offs. If the price of the lamp you’re looking to buy seems like an incredible bargain, it’s properly  a counterfeit been created using inferior parts. Knock-offs are susceptible to explosions and have a shorter life span.

These knock off lamps have not been properly calibrated to work with the sensitive components and can have damage your Sanyo PLC-XU50/ PLC-XU55 projector. Buying a knock-off lamp will also void your warranty and should anything happen to the projector you will not be covered. Be smart and investor an original Sanyo POA-LMP55 (service part no 610 309 2706).

Installing the Sanyo POA-LMP55 lamp

NOTE: Allow the Sanyo PLC-XU50 / PLC-XU55 projector to thoroughly cool before changing the lamp. Turn off the projector, unplug the AC cord and allow 45 to 60 minutes for the projector to cool. These projectors operate under high heat and there is a possibility of being burned, if the projector is not fully cooled before changing the Sanyo POA-LMP55 (service part no 610 309 2706) lamp.

• The lamp cover for the Sanyo PLC-XU50 / PLC-XU55 is found on the bottom of the projector. Gently turn projector over and loosen the screw holding the cover in place. Place the cover to one side.
• Inside you’ll find the Sanyo POA-LMP55 (service part no 610 309 2706) lamp cage. Loosen  both screws  holding the lamp cage in place.
• Grab the lamp handle and gently lift the lamp out of its socket. Place to one side. Be sure to dispose of the used lamp through a local recycling program. Don’t throw this lamp into regular garbage as it contains mercury.
• Place the new  Sanyo POA-LMP55 into the slot using the handle and not touching the actual bulb.
• Once the lamp is in, tighten both screws on the Sanyo POA-LMP55 (6103092706) lamp assembly. Make sure the screws have been tightened properly or the Sanyo PLC-XU50 / PLC-XU55 projector will not turn on.
• Replace the Lamp Cover and tighten the screw. Re-connect the power cord and turn on the Sanyo PLC-XU50 / PLC-XU55 projector. If the Sanyo POA-LMP55 (service part no 610 309 2706) lamp does not turn on after the warm-up period, try re-installing the lamp.
• Reset the Lamp Replace Counter following the instructions below.

NOTE: Your old  Sanyo POA-LMP55 (service part no 610 309 2706) lamp should be properly recycled. These lamps contain mercury and can’t be placed into common garbage.

STEP THREE: Reset the Sanyo PLC-XU50 / PLC-XU55 Lamp Replace Counter

The Lamp Replace Counter for the Sanyo PLC-XU50 / PLC-XU55 will track the correct age of your newly installed lamp and trigger the Lamp Replacement Indicator. Failure to reset the counter may result in the projector not tracking the end of life for the Sanyo POA-LMP55 (610-309-2706) and letting the projector inadvertently use the lamp past its normal life cycle. Your  Sanyo PLC-XU50 / PLC-XU550 may stop working suddenly if the Lamp Replace Counter has not been properly set.

• Press the MENU Button to display the MAIN MENU. Press the POINT LEFT/RIGHT button and scroll right to select SETTING.
• Press the SELECT button to display the SETTING DISPLAY menu.
• Press the POINT DOWN button (a red arrow will appear).
• Move the red arrow to the LAMP AGE and then press the SELECT button.
• The message “Lamp replace counter reset?”  appears. Move the arrow down to YES and press the SELECT button.
• Move the arrow to QUIT and press the SELECT button.

3 tips for extending the life of the Sanyo POA-LMP55 projector lamp

Extend the life of your newly installed Sanyo POA-LMP55 (service part no 610 309 2706) by following these helpful tips:

• Wait at least five minutes before turning the Sanyo PLC-XU50 / PLC-XU55 projector off.
• Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
• Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP55 (service part no 610 309 2706) and prevent the Sanyo PLC-XU50 / PLC-XU55 projector from overheating.

The post How to replace the Sanyo PLC-XU50 / PLC-XU55 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Sanyo PLC-XU47 projector

Follow our easy 3-step guide to a new projector lamp.

STEP ONE: Purchase the correct projector lamp

The lifespan of your Sanyo POA-LMP55 (service part no 610 309 2706) lamp will vary depending on how much the projector is used and if the filters are cleaned regularly. When the Sanyo PLC-XU47 / PLC-XU48 projector lamp is nearing its end of life you’ll notice the Lamp Replacement indicator is blinking yellow.

Other warning sings may include a picture that is dim with unnatural colors or a projector that won’t turn on.

Sanyo PLC-XU48 projector

Save money and protect your  Sanyo PLC-XU47 / PLC-XU48  projector by investing in an original Sanyo POA-LMP55 (610-309-2706) projector lamp. Generic lamps may look like a great bargain since they are generally cheaper, however, these knock-off lamps are created with inferior materials and may actually cost you more in the long run. Knock-offs are susceptible to explosions, have a shorter life span and can damage the precise components in your Sanyo PLC-XU47 / PLC-XU48projector. Installing a knock-off generic lamp also voids your warranty.

Learn more about spotting dangerous projector lamps by reading our article: 7 tips for spotting counterfeits.

STEP TWO: Install the Sanyo POA-LMP55 lamp

NOTE: Allow the Sanyo PLC-XU47 / PLC-XU48 projector to thoroughly cool before changing the lamp. Turn off the projector, unplug the AC cord and allow 45 to 60 minutes for the projector to cool. These projectors operate under high heat and there is a possibility of being burned, if the projector is not fully cooled before changing the Sanyo POA-LMP55 (service part no 610 309 2706) lamp.

• The lamp cover for the Sanyo PLC-XU47 / PLC-XU48 is at the bottom of the projector. Gently turn projector over and loosen the screw holding the cover in place. Place the cover to one side.
• Inside you’ll find the Sanyo POA-LMP55 (service part no 610 309 2706) lamp cage. Loosen both screws holding the lamp cage in place.
• Grab the lamp handle and gently lift the lamp out of its socket. Place to one side. Be sure to dispose of the used lamp through a local recycling program. Don’t throw this lamp into regular garbage as it contains mercury.
• Taking the new Sanyo POA-LMP55 lamp assembly by the handle place it into the slot. Avoid touching the actual bulb as the oil from your fingers can burn a black spot on the lenses or you can accidentally break the bulb. Don’t force the lamp into place — it should slide into the slot easily.
• Once the lamp is in, tighten both screws on the Sanyo POA-LMP55 (6103092706) lamp assembly. Make sure the screws have been tightened properly or the Sanyo PLC-XU47 / PLC-XU48 projector will not turn on.
• Replace the Lamp Cover and tighten the screw. Re-connect the power cord and turn on the Sanyo PLC-XU47 / PLC-XU48 projector. If the Sanyo POA-LMP55 (service part no 610 309 2706) lamp does not turn on after the warm-up period, try re-installing the lamp.
• Reset the Lamp Replacement Counter following the instructions below.

NOTE: Your old  Sanyo POA-LMP55 (service part no 610 309 2706) lamp should be properly recycled. These lamps contain mercury and can’t be placed into common garbage.

STEP THREE: Reset the Sanyo PLC-XU47 / PLC-XU48 Lamp Replace Counter

The Lamp Replace Counter for the  Sanyo PLC-XU47 / PLC-XU48 will track the correct age of your newly installed lamp and trigger the Lamp Replacement Indicator. Failure to reset the counter may result in the projector not tracking the end of life for the Sanyo POA-LMP55 (610-309-2706) and letting the projector inadvertently use the lamp past its normal life cycle. Your  projector may stop working suddenly if the Lamp Replace Counter has not been properly set.

• Press the MENU Button to display the MAIN MENU. Press the POINT LEFT/RIGHT button and scroll right to select SETTING.
• Press the SELECT button to display the SETTING DISPLAY menu.
• Press the POINT DOWN button (a red arrow will appear).
• Move the red arrow to the LAMP AGE and then press the SELECT button.
• The message “Lamp replace counter reset?”  appears. Move the arrow down to YES and press the SELECT button.
• Move the arrow to QUIT and press the SELECT button.

3 tips for extending the life of the Sanyo POA-LMP55 projector lamp

Extend the life of your newly installed Sanyo POA-LMP55 (service part no 610 309 2706) by following these helpful tips:

• Wait at least five minutes before turning the Sanyo PLC-XU47 / PLC-XU48 projector off.
• Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
• Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP55 (service part no 610 309 2706) and prevent the  Sanyo PLC-XU47 / PLC-XU48 projector from overheating.

The post Install a new Sanyo PLC-XU47 / PLC-XU48 projector lamp in 3 easy steps appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Sanyo PLC-XU25 projector

STEP-BY-STEP INSTRUCTIONS FOR PLC-XU25 LAMP REPLACEMENT

If your projector Sanyo PLC-XU25 lamp no longer turns on, it needs to be replaced.  If the picture is dim or looks unnatural the Sanyo POA-LMP55 (service part no 610 309 2706) is reaching its end of life.

If the Replace Lamp Indicator light on the front panel is blinking orange, you must replace the Sanyo POA-LMP55 immediately. Follow our simple step-by-step instructions to replace your lamp in the Sanyo PLC-XU25 projector easily.

Sanyo PLC-XU25 warning light

Replace the Sanyo POA-LMP55 (610 309 2706) immediately with a guaranteed authentic lamp. Be sure to verify that your lamp is authentic and buy from an authorized manufacturer.

If the price of the lamp you’re about to buy seems like an incredible bargain, chances are it’s counterfeit and has been created using inferior parts that  can damage the highly sophsticated componenbts in your Sanyo PLC-XU25 projector since it will not fit properly. Buying a knock-off lamp will also void your warranty and should anything happen to the projector you will not be covered.

Before installation

Allow the Sanyo PLC-XU25 projector to thoroughly cool before changing the lamp. Turn off the projector, unplug the AC cord and allow 45 to 60 minutes for the projector to cool. These projectors operate under high heat and there is a possibility of being burned, if the projector is not fully cooled before changing the Sanyo POA-LMP55 (service part no 610 309 2706) lamp.

Replacing the Sanyo POA-LMP55 (610-309-2706) Lamp Assembly

1. Turn off the Sanyo PLC-XU25 projector.
2. The lamp cover for the Sanyo PLC-XU25 projector is located at the bottom of the projector. Gently turn over the projector onto its side and loosen the screw holding the cover in place. Place the cover to one side.
3. Inside you’ll find the Sanyo POA-LMP55 (service part no 610 309 2706) lamp cage. Loosen both screws holding the lamp cage in place. Grab the lamp handle and gently lift the lamp out of its socket. Place to one side. Be sure to dispose of the lamp properly through a local recycling program.
4. Taking the new Sanyo POA-LMP55 (6103092706) lamp cage by the handle—avoid touching the actual bulb a this can break or damage the lamp. Without forcing the lamp, place it into the slot.
5. Once the lamp is in, tighten both screws on the Sanyo POA-LMP55 Lamp Assembly. Make sure the screws have been tightened properly or the Sanyo PLC-XU25 projector will not turn on.
6. Replace the Lamp Cover and tighten the screw. Re-connect the power cord and turn on the Sanyo PLC-XU25 projector. If the Sanyo POA-LMP55 (610-309-2706) lamp does not turn on after the warm-up period, try re-installing the lamp. Reset the Lamp Counter Screen by following the instructions below.

NOTE: Your old  Sanyo POA-LMP55 (service part no 610 309 2706) lamp should be properly recycled. These lamps contain mercury and can’t be placed into common garbage.

RESETTING THE LAMP REPLACE COUNTER  

In order for the projector to properly track the lamp life of your newly installed Sanyo POA-LMP55 (service part no 610 309 2706)you’ll need to reset the Lamp Replace Counter on the Sanyo PLC-XU25. Failure to do so can result in the Replace Lamp Indicator not tracking the lamp life properly.

• Press SELECT (rear click) to have the SETTING DISPLAY screen appear.
• Press the POINT DOWN button and a red arrow shows up on screen.
• Using the POINT UP/DOWN button, select the LAMP PAGE and then press SELECT.
• You’ll see the message “Lamp replace counter reset?“
• Move the arrow to YES and press SELECT.
• OK is shown for confirmation. Press YES and then the SELECT button.
• Move the arrow QUIT and press SELECT to exit the MENU and return to the screen.
• Your newly installed Sanyo POA-LMP55 (service part no 610 309 2706) should last between 1,000 to 2,000 hours depending on usage and maintenance.

EXTEND THE LIFE OF THE POA-LMP55 LAMP

Make your newly installed Sanyo POA-LMP55 (service part no 610 309 2706) last longer:

• Wait at least five minutes before turning the Sanyo PLC-XU25 projector off.
• Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
• Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP55 (service part no 610 309 2706) and prevent the Sanyo PLC-XU25 from overheating.

.

The post Your easy guide for replacing the Sanyo PLC-XU25 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.