When to replace the Sanyo POA-LMP65 projector lamp

Projectors using the Sanyo POA-LMP65 (service parts no 610 307 7925) lamp:

• Sanyo PLC-XU56
• Sanyo PLC-XE20
• Sanyo PLC-SU51
• Sanyo PLC-SU50
• Sanyo PLC-SL20

The Sanyo POA-LMP65 (service parts no 610 307 7925) should last between 2,000 to 3,000 hours before it needs to be replaced. Be sure to purchase an authentic version of this lamp bought from a verified source. When you purchase from a guaranteed supplier you’ll be getting a lamp specifically manufactured to meet the specifications of your projector.

The cheaper counterfeit models may be tempting since they are lower in price but they can end up costing more in the long run, especially when they damage the sensitive mechanisms in your Sanyo projectors.

Looking for a less expensive option? Are you technically saavy?  Watch our step-by-step video on replacing only the Sanyo POA-LMP65 (service parts no 610 307 7925) bulb instead of the entire lamp housing.

Scroll down for links to step-by-step instructions on replacing the Sanyo POA-LMP65 (service parts no 610 307 7925).

When the lamp life is used up and at 0 hour, the Lamp replacement icon will appear on screen, indicating that is it’s urgent to replace the Sanyo POA-LMP65 (service parts no 610 307 7925) lamp.

You must wait for 90 seconds after changing Lamp Mode before you can access this option again.

For step-by-step instructions on replacing your Sanyo POA-LMP65 (service parts no 610 307 7925) lamp, click on your model listed below:

Sanyo PLC-SL56, Sanyo POA-LMP65 service part no 610 307 7925

Click here for step-by-step instructions on how to change the Sanyo POA-LMP65 (service parts no 610 307 7925) for theSanyo PLC-XU56 projector.

Sanyo PLC-XE20 projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP65 (service parts no 610 307 7925) for the Sanyo PLC-XE20 projector.

Sanyo PLC-SU51 projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP65 (service parts no 610 307 7925) for the Sanyo PLC-SU51 projector.

Sanyo PLC-SU50 projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP65 (service parts no 610 307 7925) for the Sanyo PLC-SU50 projector.

Sanyo PLC-SL20 projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP65 (service parts no 610 307 7925) for theSanyo PLC-SL20 projector.

The post When to replace the Sanyo POA-LMP65 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Sanyo PLC-XE20 projector

Follow our easy 3-step guide to a new Sanyo PLC-XE20 projector lamp.

Signs you need to replace the Sanyo POA-LMP65 (service parts no 610 307 7925) in the Sanyo PLC-XE20 projector:

When you see these signs, change the Sanyo POA-LMP65 (service parts no 610 307 7925) immediately.

STEP ONE: Purchase the correct projector lamp

The best thing you can do to prolong the life of your Sanyo PLC-XE20  and save money is to invest in an original Sanyo POA-LMP65 (service parts no 610 307 7925) projector lamp. Generic lamps look like a great bargain since they are generally cheaper, however, these knock-off lamps are created with inferior materials. They are susceptible to explosions, have a shorter life span and can damage the precise components in your Sanyo PLC-XE20 projector. Installing a knock-off generic lamp also voids your warranty.

Learn more about spotting dangerous projector lamps by reading our article: 7 tips for spotting counterfeits.

Looking for a less expensive option? Are you technically saavy?  Watch our step-by-step video on replacing only the Sanyo POA-LMP65 (service parts no 610 307 7925) bulb instead of the entire lamp housing.

STEP TWO: Install the Sanyo POA-LMP65 lamp

• NOTE: Allow the Sanyo PLC-XE20 projector to thoroughly cool before changing the lamp. Turn off the projector, unplug the AC cord and allow 45 to 60 minutes for the projector to cool. These projectors operate under high heat and there is a possibility of being burned, if the projector is not fully cooled before changing the lamp.
• The lamp cover for the Sanyo PLC-XE20 is at the bottom of the projector. Gently turn projector over and loosen the screw holding the cover in place. Place the cover to one side.
• Inside you’ll find the Sanyo POA-LMP65 (service parts no 610 307 7925) lamp cage. Loosen all three screws holding the lamp cage in place.
• Grab the lamp handle and gently lift the lamp out of its socket. Place to one side. Be sure to dispose of the used lamp through a local recycling program. Don’t throw this lamp into regular garbage as it contains mercury.
• Taking the new Sanyo POA-LMP65 (service parts no 610 307 7925) lamp assembly by the handle place it into the slot. Avoid touching the actual bulb as the oil from your fingers can burn a black spot on the lenses or you can accidentally break the bulb. Don’t force the lamp into place — it should slide into the slot easily.
• Once the lamp is in, tighten all three screws on the Sanyo POA-LMP65 (service parts no 610 307 7925) lamp assembly. Make sure the screws have been tightened properly or the Sanyo PLC-XE20 projector will not turn on.
• Replace the Lamp Cover and tighten the screw. Re-connect the power cord and turn on the PLC-XE20 projector. If the Sanyo POA-LMP65 lamp does not turn on after the warm-up period, try re-installing the lamp.
• Reset the Lamp Replace Counter following the instructions below.

NOTE: Your old  Sanyo POA-LMP65 (service parts no 610 307 7925) lamp should be properly recycled. These lamps contain mercury and can’t be placed into common garbage.

STEP THREE: Reset the Sanyo PLC-XE20 Lamp Replace Counter

The Lamp Replace Counter for the  Sanyo PLC-XE20 will track the correct age of your newly installed lamp and trigger the Lamp Replacement Indicator. Failure to reset the counter may result in the projector not tracking the end of life for the Sanyo POA-LMP65 (service parts no 610 307 7925) and letting the projector inadvertently use the lamp past its normal life cycle. Your  Sanyo PLC-XE20 may stop working suddenly if the Lamp Replace Counter has not been properly set.

• Press the MENU Button to display the MAIN MENU. Press the POINT LEFT/RIGHT button and scroll right to select SETTING.
• Press the SELECT button to display the SETTING DISPLAY menu.
• Press the POINT DOWN button (a red arrow will appear).
• Move the red arrow to the LAMP AGE and then press the SELECT button.
• The message “Lamp replace counter Reset?”  appears. Move the arrow down to YES and press the SELECT button.
• Move the arrow to QUIT and press the SELECT button.

3 tips for extending the life of the Sanyo POA-LMP65 projector lamp

Extend the life of your newly installed Sanyo POA-LMP65 by following these helpful tips:

• Wait at least five minutes before turning the PLC-XE20 projector off.
• Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
• Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP65 (service parts no 610 307 7925) and prevent the  PLC-XE20 projector from overheating.

The post 3 Steps to a new Sanyo PLC-XE20 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.