Step 1: Watch the warning signs

When the Epson PowerLite 1715 projector lamp is approaching end of life you’ll notice the lamp light on the projector flashing orange. The image may appear dim and the colours darker than normal. When you see the “Replace the lamp” message flashing on the screen replace the lamp immediately.

Step 2: Buy the right lamp

While there are plenty of cheaper options, you should go with authentic Epson ELPLP38 lamps for a number of reasons. Watch for the seal of approval displayed by authorized dealers so you know you are purchasing an authentic lamp.

Be aware that most lamps advertised as “generic” or “compatible” are usually counterfeit lamps with inferior workmanship and will not last the full 3000 hours. But even worse, because these lamps can’t be calibrated properly, they can damage the sensitive optics in your Epson PowerLite 1715. Most are also a health hazard because of the toxic materials used.

Installing a non-OEM Epson ELPLP38 voids any warranty on your Epson PowerLite 1715. Better to avoid generics posing as authentic lamps.

Buy this lamp on Amazon from the following authorized dealers:

• EPSON ELPLP38 replacement lamp for powerlite 1700c 1705c 1710c 1715c – NEW – Retail – V13H010L38
• EPSON EMP-1705 Replacement Projector Lamp ELPLP38 / V13H010L38

Step 3: Replacing the lamp

Before installation follow these important safety tips:

Turn power button off. Wait for the two beeps that follow and unplug the power cord on the Epson PowerLite 1715.
Wait until the projector is cool to the touch.
DO NOT attempt to change the Epson ELPLP38 if the projector is still hot. You get badly burned if you don’t wait for the projector to cool.

IMPORTANT: Do not operate the projector when the lamp is removed as this may result in malfunctions, fire hazard and other accidents.

• Loosen the screw on the Epson PowerLite 1715 projector cover using the screwdriver provided.

Slide the lamp cover to the side and lift it off the Epson PowerLite 1715 projector.

Loosen the two screws holding the Epson ELPLP38 lamp in place. NOTE: You can only loosen these screws. They don’t come out all the way.

Grab the two tabs on either side of the the Epson ELPLP38 lamp and slowly pull out the lamp out of the Epson PowerLite 1715 projector. Don’t use excessive force or the lamp could break.  What to do if lamp breaks inside the projector.

NOTE: The Epson ELPLP38 should not be thrown into the regular garden and needs to be properly recycled. Contact your authentic manufacturer and they can assist you in getting the lamp to the right recycling facility.

Gently insert the new Epson ELPLP38 lamp into the Epson PowerLite 1715 projector.
Avoid touching the actual lamp since your fingerprints will cause black out spots to appear when the projector starts working.
Push down the corner marked PUSH until the lamp snaps in.
Once the Epson ELPLP38 lamp is fully inserted, tighten the screws.
Slide out the air filters found at the bottom of the projector. Remove the current filter.
Slide in the new air filter until it clicks into place.
You are now ready to reset the lamp timer.

Resetting the Epson PowerLite 1715c Lamp Timer

It’s important to reset the PowerLite 1715 has a lamp timer each time a new lamp is installed so the projector can accurately track the Epson ELPLP38 lamp. Never use the Epson ELPLP38 lamp beyond its recommended usage as this can damage the Epson 1715 projector beyond repair.

Press MENU
Scroll down to RESET. Press ENTER.
Scroll down RESET LAMP HOURS. Press ENTER.
A second prompt screen will appear. Select YES at the prompt screen. Press ENTER.
Press ESC or MENU to exit.

Extending the life of your Epson ELPLP38 lamp

Follow this simple tips to make your Epson ELPLP38 lamp last even longer:

• Keep your air filters clean to avoid overheating the projector and causing the lamp to overheat.
• Turn off the Epson PowerLite 1715 projector for at least one hour ever 24 hours.
• Don’t overuse the lamp. An average use of four to five hours per day will ensure longer lamp life.
• Make sure there is enough airflow around the projector particularly if it’s been permanently mounted so it doesn’t overheat.
• Set the Brightness Mode to low. Prolong the life of the Epson ELPLP38 from 2000 hours to 3000 hours by lowering the Brightness Control to low!
• Learn more with Top tips for extending DLP projector lamp life

The post Replacing the Epson PowerLite 1715 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Wondering which projectors can be paired with the Epson ELPLP38 lamp? Keep reading.

Before you install any Epson ELPLP38 lamp look for the seal of approval and be sure to buy authentic:

• authentic lamps have a longer life than generics
• generic lamps are created with toxic materials and have NO saftey standards
• authentic last the entire 3000 hours and will not explode
• copycat lamps can damage the sensitive electronics in your projectors
• generics don’t come with a guarantee or tech support. Getting a refund can be a hassle.
• your warranty on the Epson will be void if you install a generic lamp.
• Find out how to protect yourself from being tricked into buying counterfeit lamps.

Buy this lamp on Amazon from the following authorized dealers:

• EPSON ELPLP38 replacement lamp for powerlite 1700c 1705c 1710c 1715c – NEW – Retail – V13H010L38
• EPSON EMP-1705 Replacement Projector Lamp ELPLP38 / V13H010L38

Compatible projectors with the Epson ELPLP38 lamp

The Epson ELPLP38 is an authentic projector lamp compatible with the following Epson Projectors:

Epson EMP-1700, Epson EMP-1705, Epson EMP-1707, Epson EMP-1710, Epson EMP-1715, Epson EMP-1717, Epson PowerLite 1505, Epson PowerLite 1700, Epson PowerLite 1700c, Epson PowerLite 1705c, Epson PowerLite 1710, Epson PowerLite 1710c, Epson PowerLite 1715c, Epson PowerLite 1717c.

For step-by-step instructions on replacing your Epson ELPLP38 lamp, click on your projector listed below:

Click here for step-by-step instructions on how to change the Epson ELPLP38 projector lamp for the Epson EMP-1700 projector.

Click here for step-by-step instructions on how to change the Epson ELPLP38 projector lamp for the Epson EMP-1705 projector.

Click here for step-by-step instructions on how to change the Epson ELPLP38 projector lamp for the Epson EMP-1707 projector.

Click here for step-by-step instructions on how to change the Epson ELPLP38 projector lamp for the Epson EMP-1710 projector.

Click here for step-by-step instructions on how to change the Epson ELPLP38 projector lamp for the Epson EMP-1715 projector.

Click here for step-by-step instructions on how to change the Epson ELPLP38 projector lamp for the Epson EMP-1717 projector.

How to extend the life of the Epson ELPLP38 lamp:

Extend the life of the newly installed Epson ELPLP38 with the following tips:

• Keep your air filters clean to avoid overheating the projector.
• Turn off the Epson projectors and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
• Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
• Set the Brightness Mode to low or Econo Mode to extend lamp life.
• Learn more with Top tips for extending DLP projector lamp life.

The post Projectors compatible with the Epson ELPLP38 lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Replacing the Epson Powerlite 1715c projector lamp can be completed in three easy steps.

Step 1: Watch the warning signs

When the Epson ELPLP38 is approaching end of life in the Epson PowerLite 1715c you’ll see the following warning signs:

• lamp light on projector continually flashes orange
• “Replace the lamp” message appears on screen.
• image is gradually dimming or starting to deteriorate.
• Colors appear darker than normal

Prolong the life of the Epson ELPLP38 from 2000 hours to 3000 hours by lowering the Brightness Control to low!

Step 2: Have the correct type of lamp

While there are plenty of cheaper options, you should go with authentic Epson ELPLP38 lamps for a number of reasons. Watch for the seal of approval displayed by authorized dealers so you know you are purchasing an authentic lamp.

Be aware that most lamps advertised as “generic” or “compatible” are usually counterfeit lamps with inferior workmanship and will not last the full 3000 hours. But even worse, because these lamps  can’t be calibrated properly, they can damage the sensitive optics in your Epson PowerLite 1715c. Most are also a health hazard because of the toxic materials used.

Installing a non-OEM Epson ELPLP38 voids any warranty on your Epson PowerLite 1715c. Better to avoid generics posing as authentic lamps.

Buy this lamp on Amazon from the following authorized dealers:

• EPSON ELPLP38 replacement lamp for powerlite 1700c 1705c 1710c 1715c – NEW – Retail – V13H010L38
• EPSON EMP-1705 Replacement Projector Lamp ELPLP38 / V13H010L38

Step 3: Replacing the lamp

Before installation follow these important safety tips:

• Turn power button off. Wait for the two beeps that follow and unplug the power cord on the Epson PowerLite 1715c.
• Wait until the projector is cool to the touch.
• DO NOT attempt to change the Epson ELPLP38 if the projector is still hot. You get badly burned if you don’t wait for the projector to cool.

IMPORTANT: Do not operate the projector when the lamp is removed as this may result in malfunctions, fire hazard and other accidents.

• Loosen the screw on the Epson PowerLite 1715c projector cover using the screwdriver provided.

• Slide the lamp cover to the side and lift it off the Epson PowerLite 1715c projector.

Loosen the two screws holding the Epson ELPLP38 lamp in place. NOTE: You can only loosen these screws. They don’t come out all the way.

• Grab the two tabs on either side of the the Epson ELPLP38 lamp and slowly pull out the lamp out of the Epson PowerLite 1715c projector.
• Don’t use excessive force or the lamp could break.
• What to do if lamp breaks inside the projector.
• NOTE: The Epson ELPLP38 should not be thrown into the regular garden and needs to be properly recycled.

• Gently insert the new Epson ELPLP38 lamp into the Epson PowerLite 1715c projector.
• Avoid touching the actual lamp since your fingerprints will cause black out spots to appear when the projector starts working.
• Push down the corner marked PUSH until the lamp snaps in.
• Once the Epson ELPLP38 lamp is fully inserted, tighten the screws.
• Slide out the air filters found at the bottom of the projector. Remove the current filter.
• Slide in the new air filter until it clicks into place.
• You are now ready to reset the lamp timer.

Resetting the Epson PowerLite 1715c Lamp Timer

It’s important to reset the PowerLite 1715c has a lamp timer each time a new lamp is installed so the projector can accurately track the Epson ELPLP38 lamp. Never use the Epson ELPLP38 lamp beyond its recommended usage as this can damage the Epson 1715c projector beyond repair.

• Press MENU.
• Scroll down to RESET. Press ENTER.
• Scroll down RESET LAMP HOURS. Press ENTER.
• A second prompt screen will appear. Select YES at the prompt screen. Press ENTER.
• Press ESC or MENU to exit.

Extending the life of your Epson ELPLP38 lamp

Follow this simple tips to make your Epson ELPLP38 lamp last even longer:

• Keep your air filters clean to avoid overheating the projector and causing the lamp to overheat.
• Turn off the Epson PowerLite 1715c projector for at least one hour ever 24 hours.
• Don’t overuse the lamp. An average use of four to five hours per day will ensure longer lamp life.
• Make sure there is enough airflow around the projector particularly if it’s been permanently mounted so it doesn’t overheat.
• Set the Brightness Mode to low.
• Learn more with Top tips for extending DLP projector lamp life

The post 3 steps to a new Epson Powerlite 1715c projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Warning message on screen? Image that is gradually becoming dimmer? You need to replace the Epson PowerLite 1505 projector lamp.

Follow this easy step-by-step guide for a do-it-yourself lamp replacement that is easy and hassle free.

Go with authentic lamps

While generic lamps are tempting because of their bargain prices, there are six good reasons you should avoid them:

• inferior workmanship which translates to an inferior product,
• they can’t last the full 3000 hours.
• can’t be calibrated properly so can seriously damage the optics in your Epson PowerLite 1505.
• present a health hazard due to their toxic materials.
• installing a generic lamp will void the warranty on the Epson PowerLite 1505.
• offer no guarantee, technical or customer service even after the lamp has been purchased.

Buy an authentic lamp from a recognized dealer who proudly displays the seal of approval. Read about how generics posing as authentic lamps. 

You can expect between 2000 t0 3000 hours before the Epson ELPLP38 needs to be replaced. The lamp is used up much faster with the Brightness Control is set to High. A low Brightness Control will give you the full 3000 hours.

Buy this lamp on Amazon from the following authorized dealers:

• EPSON ELPLP38 replacement lamp for powerlite 1700c 1705c 1710c 1715c – NEW – Retail – V13H010L38
• EPSON EMP-1705 Replacement Projector Lamp ELPLP38 / V13H010L38

Replacing the Epson ELPLP38 lamp

Before installation follow these important safety tips:

• Turn power button off and after the Epson PowerLite 1505 has beeped twice unplug the power cord.
• The Epson PowerLite 1505 should be cool to the touch.
• DO NOT attempt to change the Epson ELPLP38 if the projector is still hot. You get badly burned if you don’t wait for the projector to cool.

IMPORTANT: Do not operate the projector when the lamp is removed as this may result in malfunctions, fire hazard and other accidents.

• Loosen the screw on the Epson PowerLite 1505 projector cover using the screwdriver provided.

• Slide the lamp cover to the side and lift it off the Epson PowerLite 1505 projector.

Loosen the two screws holding the Epson ELPLP38 lamp in place. Theses screws don’t come out all the way.

• Grab the two tabs on either side of the the Epson ELPLP38 lamp and slowly pull out the lamp out of the Epson PowerLite 1505 projector.
• Don’t use excessive force or the lamp could break.
• Read this article about what to do if lamp breaks inside the projector.

• NOTE: The Epson ELPLP38 should not be thrown into the regular garden and needs to be properly recycled.

FINAL STEPS

• Gently insert the new Epson ELPLP38 lamp into the Epson PowerLite 1505 projector.
• Avoid touching the actual lamp since your fingerprints will cause black out spots to appear when the projector starts working.
• Tighten the screws on the Epson ELPLP38 lamp. Be sure not to tighten too much or the lamp may not work.
• Replace the lamp cover and tighten the screw on the Epson ELPLP38 projector lamp cover.
• You are now ready to reset the lamp timer.

Resetting the Lamp Timer

It’s important to reset the PowerLite 1505 has a lamp timer each time a new lamp is installed so the projector can accurately track the Epson ELPLP38 lamp. Never use the Epson ELPLP38 lamp beyond its recommended usage as this can damage the Epson 1505 projector beyond repair.

• Press MENU.
• Scroll down to RESET. Press ENTER.
• Scroll down RESET LAMP HOURS. Press ENTER.
• A second prompt screen will appear. Select YES at the prompt screen. Press ENTER.
• Press ESC or MENU to exit.

Extending the life of your Epson ELPLP38 lamp

Follow this simple tips to make your Epson ELPLP38 lamp last even longer:

• Keep your air filters clean to avoid overheating the projector.
• Turn off the Epson PowerLite 1505 projector and let it stand for at least one hour ever 24 hours.
• An average use of four to five hours per day will ensure longer lamp life.
• Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
• Set the Brightness Mode to low.
• Learn more with Top tips for extending DLP projector lamp life

The post Replace the Epson PowerLite 1505 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Is your projector image dim or the colours deteoriating? It may be time to replace the Epson EMP-1707 projector lamp. This guide will give you step-by-step instructions for quick and easy replacement.

Buy the right lamp

What’s the difference between an authentic pson EMP-1707 projector lamp and a generic lamp? Quality, price and reliability! Buy an authentic lamp from a recognized dealer who proudly displays the seal of approval.

6 reasons to avoid generic lamps

• they can’t last the full 3000 hours
• inferior workmanship can damage the optics in the Epson EMP-1707
• improperly calibrated so
• present a health hazard due to their toxic materials.
• installing a generic lamp will void the warranty on the Epson EMP 1707.
• offer no guarantee, technical or customer service even after the lamp has been purchased.

Read about how generics pose as authentic lamps.

Buy this lamp on Amazon from the following authorized dealers:

• EPSON ELPLP38 replacement lamp for powerlite 1700c 1705c 1710c 1715c – NEW – Retail – V13H010L38
• EPSON EMP-1705 Replacement Projector Lamp ELPLP38 / V13H010L38

Replacing the Epson ELPLP38 lamp

Before installation follow these important safety tips:

• Turn power button off and after the Epson EMP-1707 has beeped twice unplug the power cord.
• The Epson EMP-1707 should be cool to the touch. DO NOT attempt to change the Epson ELPLP38 if the projector is still hot. You can be badly burned if you don’t wait for the projector to cool.

IMPORTANT: Do not operate the projectors the lamps is removed as this may result in malfunctions, fire hazard and other accidents.

Loosen the screws on the Epson EMP-1707 projector using the screwdriver provided.

Slide the cover towards you until it’s off the runners. Lift and remove the cover on the Epson EMP-1707 projector.

Loosen the two screws holding the Epson ELPLP38 lamp in place

Grab the side indents and gently lift the Epson ELPLP38 lamp out of the Epson EMP-1707 projector. Don’t use excessive force or the lamp could break. Read about what to do if lamp breaks inside the projector.

NOTE: The Epson ELPLP38 lamp contains mercury and needs to be properly recycled. Don’t throw the used lamp into your regular garbage.

Gently insert the new Epson ELPLP38 lamp into the Epson EMP-1707 projector. Avoid touching the actual lamp since your fingerprints will cause black out spots to appear when the projector starts working.

Tighten the screws on the Epson ELPLP38 lamp. Be sure not to tighten too much or the lamp may not work.

Replace the Epson EMP-1707 projector lamp cover and tighten the screw on the lamp cover.

You are now ready to reset the lamp timer.

Resetting the Epson EMP-1707 Lamp Timer

It’s important to reset the Epson EMP-1707 has a lamp timer each time a new lamp is installed so the projector can accurately track the Epson ELPLP38. Never use the Epson ELPLP38 lamp beyond its recommended usage as this can damage the Epson EMP-1707 projector beyond repair.

• Press the MENU button on either the remote control or on the projector’s control panel.
• Scroll down to the RESET option. Press Enter to bring up the reset screen.
• Scroll down to RESET LAMP HOURS.
• A second prompt screen will appear asking for confirmation. Scroll over to the YES option. Press ENTER.
• Press MENU to exit.

Extending the life of your Epson ELPLP38 lamp

Follow this simple tips to make your Epson ELPLP38 lamp last even longer:

• Keep your air filters clean to avoid overheating the projector.
• Turn off the Epson EMP-1707 projector and let it stand for at least one hour ever 24 hours.
• An average use of four to five hours per day will ensure longer lamp life.
• Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
• Set the Brightness Mode to low.
• Learn more with Top tips for extending DLP projector lamp life

The post How to change the Epson EMP-1707 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Follow our  3-step manual to install a new Epson EMP-1717 projector lamp.

STEP 1: Know when to replace

If you have sent the Brightness Control to High (the default setting), you can expect the Epson EMP-1717 projector lamp to last up to 2000 hours. Gain more time or the lamp; when you set Brightness Control is to Low, the lamp will last up to 3000 hours.

You’ll start to see the following warning signs when the Epson EMP-1717 projector lamp is approaching end of life:

• A screen that is gradually dimming or deteriorating.
• Colour in the image appears dark or off colour.
• “Replace the lamp” warning flashing on screen.
• Lamp light flashing a steady orange.

Forcing the lamp to work beyond it’s estimated life can result in the lamp exploding insider your EMP-1717 projector.Your Epson EMP-1717 projector needs model Epson ELPLP38.

STEP 2: Buy the right lamp

The Internet is flooded with companies selling generic lamps at reduced prices. What’s the difference between an authentic Epson ELPLP38 and a generic lamp? Quality, price and reliability! Buy an authentic lamp from a recognized dealer who proudly displays the seal of approval.

Generic lamps have six main problems:

• inferior workmanship which translates to an inferior product,
• they can’t last the full 3000 hours.
• improperly calibrated  so they won’t every work properly and can seriously damage the optics in your Epson EMP 1717
• present a health hazard due to their toxic materials.
• installing a generic lamp will void the warranty on the Epson EMP 1717
• offer no guarantee, technical or customer service even after the lamp has been purchased.

Read about how generics pose as authentic lamps.

Buy this lamp on Amazon from the following authorized dealers:

• EPSON ELPLP38 replacement lamp for powerlite 1700c 1705c 1710c 1715c – NEW – Retail – V13H010L38
• EPSON EMP-1705 Replacement Projector Lamp ELPLP38 / V13H010L38

STEP 3: Replacing the Epson ELPLP38 lamp

Before installation follow these important safety tips:

• Turn power button off and after the Epson EMP-1717 has beeped twice unplug the power cord.
• The Epson EMP-1717 should be cool to the touch. DO NOT attempt to change the Epson ELPLP38 if the projector is still hot. You can be badly burned if you don’t wait for the projector to cool.

IMPORTANT: Do not operate the projectors the lamps is removed as this may result in malfunctions, fire hazard and other accidents.

1. Loosen the screws on the Epson EMP-1717 projector using the screwdriver provided.

2. Slide the cover towards you until it’s off the runners. Lift and remove the cover on the Epson EMP-1717 projector.

3. Loosen the two screws holding the Epson ELPLP38 lamp in place.

4. Grab the side indents and gently lift the Epson ELPLP38 lamp out of the Epson EMP-1717 projector. Don’t use excessive force or the lamp could break. Read about what to do if lamp breaks inside the projector.

NOTE: The Epson ELPLP38 lamp contains mercury and needs to be properly recycled. Don’t throw this used projector lamp into your regular garbage.

5. Gently insert the new Epson ELPLP38 lamp into the Epson EMP-1717 projector. Avoid touching the actual lamp since your fingerprints will cause black out spots to appear when the projector starts working.

6. Tighten the screws on the Epson ELPLP38 lamp. Be sure not to tighten too much or the lamp may not work.

7. Replace the Epson EMP-1707 projector lamp cover and tighten the screw on the lamp cover.

You are now ready to reset the lamp timer.

Resetting the Epson EMP-1717 Lamp Timer

It’s important to reset the Epson EMP-1717 has a lamp timer each time a new lamp is installed so the projector can accurately track the Epson ELPLP38. Never use the Epson ELPLP38 lamp beyond its recommended usage as this can damage the Epson EMP-1707 projector beyond repair.

• Press the MENU button on either the remote control or on the projector’s control panel.
• Scroll down to the RESET option. Press Enter to bring up the reset screen.
• Scroll down to RESET LAMP HOURS.
• A second prompt screen will appear asking for confirmation. Scroll over to the YES option. Press ENTER.
• Press MENU to exit.

Extending the life of your Epson ELPLP38 lamp

Follow this simple tips to make your Epson ELPLP38 lamp last even longer:

• Keep your air filters clean to avoid overheating the projector.
• Turn off the Epson EMP-1717 projector and let it stand for at least one hour ever 24 hours.
• An average use of four to five hours per day will ensure longer lamp life.
• Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
• Set the Brightness Mode to low.
• Learn more with Top tips for extending DLP projector lamp life

The post 3 Steps to a new Epson EMP-1717 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

No need to call the technician. Follow this 3-step manual for help on replacing the Epson EMP-1715 projector

Know when to replace

The life span of the Epson ELPLP38 projector lamp is 2000 hours when Brightness Control is set to High (which is the default) or 3000 hours if the Brightness Control is set to Low.

Know the warning signs

When the Epson ELPLP38 projector lamp is approaching end of life you’ll start to see the following warnings signs:

• A screen that is gradually dimming or deteriorating.
• Colour in the image appears dark or off colour.
• “Replace the lamp” warning flashing on screen.
• Lamp light flashing a steady orange.

Replace the Epson ELPLP38 projector lamp immediately so you don’t run the risk of having the lamp explode in the Epson EMP-1715 projector.

 Why buy authentic

What’s the difference between an authentic Epson ELPLP38 and a generic projector lamp? Quality, price and reliability!

The Internet is flooded with companies selling generic lamps at reduced prices. While these lamps appear to be a bargain due to their lower price tag, they can’t offer the same quality, price and reliability as authentic lamps.

Generic lamps have six main problems:

• inferior product because of inferior workmanship. They are NOT interested in your repeat business.
• generics can’t last the full 3000 hours — they have not been built properly.
• generics can seriously damage the optics in your Epson EMP 1715 projector because they can’t be calibrated properly
• generics have been created with toxic materials and are a health hazard
• installing a generic lamp will void the warranty on the Epson EMP 1715.
• generics offer no guarantee, technical or customer service even after the lamp has been purchased.

Save yourself hassles and go with authentic projector lamp from a recognized dealer who proudly displays the seal of approval. Read about generics posing as authentic lamps and how to avoid them!

Buy this lamp on Amazon from the following authorized dealers:

• EPSON ELPLP38 replacement lamp for powerlite 1700c 1705c 1710c 1715c – NEW – Retail – V13H010L38
• EPSON EMP-1705 Replacement Projector Lamp ELPLP38 / V13H010L38

Replacing the Epson ELPLP38 projector lamp

Before installation of your new projector lamp follow these important safety tips:

• Turn power button off.
• Wait until the Epson EMP-1715 has beeped twice and then unplug the power cord.
• Wait for at least one hour for the Epson EMP-1715 to be cool to the touch. DO NOT attempt to change the Epson ELPLP38 if the projector is still hot. You can be badly burned if you don’t wait for the projector to cool.

IMPORTANT: Do not operate the projectors the lamps is removed as this may result in malfunctions, fire hazard and other accidents.

1. Loosen the screws on the Epson EMP-1715 projector using the screwdriver provided.

2. Slide the cover towards you until it’s off the runners. Lift and remove the cover on the Epson EMP-1715 projector.

3. Loosen the two screws holding the Epson ELPLP38 projector lamp in place.

4. Grab the side indents and gently lift the Epson ELPLP38 projector lamp out of the Epson EMP-1715 projector. Don’t use excessive force or the projector lamp could break. If the lamp breaks inside the projector–here’s what to do.

NOTE: The Epson ELPLP38 projector lamp contains mercury and needs to be properly recycled. Don’t thrown the used lamp into your regular garbage.

5. Gently insert the new Epson ELPLP38projector  lamp into the Epson EMP-1715 projector. Avoid touching the actual projector bulb since your fingerprints will cause black out spots to appear when the projector starts working.

6. Tighten the screws on the Epson ELPLP38 projector lamp. Be sure not to tighten too much or the lamp may not work.

7. Replace the Epson EMP-1715 projector lamp cover and tighten the screw on the lamp cover.

You are now ready to reset the lamp timer.

Resetting the Epson EMP-1715 Lamp Timer

The Epson EMP-1715 has an automatic lamp timer to track the number of hours left in the lamp. Each time a new Epson ELPLP38 projector lamp is installed you need to reset the Epson EMP-1715 lamp timer. Never use the Epson ELPLP38 projector lamp beyond its recommended usage as this can damage the projector beyond repair.

• Press the MENU button on either the remote control or on the projector’s control panel.
• Scroll down to the RESET option. Press Enter to bring up the reset screen.
• Scroll down to RESET LAMP HOURS.
• A second prompt screen will appear asking for confirmation. Scroll over to the YES option. Press ENTER.
• Press MENU to exit.

Extending the life of your Epson ELPLP38 projector lamp

Follow this simple tips to make your Epson ELPLP38 projector lamp last even longer:

• Keep your air filters clean to avoid overheating the projector.
• Turn off the Epson EMP-1715 projector and let it stand for at least one hour ever 24 hours.
• An average use of four to five hours per day will ensure longer lamp life.
• Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
• Set the Brightness Mode to low.
• Learn more with Top tips for extending DLP projector lamp life

The post Replace the lamp in the Epson EMP-1715 projector appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Replacing Epson PowerLite 1717c projector lamp is simple when you follow our guide. Know when to replace the Epson PowerLite 1717c projector lamp and where to find the best lamp.

End of life warnings

When the Epson ELPLP38 is approaching end of life in the Epson PowerLite 1717c you’ll see the following warning signs:

• lamp light on projector continually flashes orange
• “Replace the lamp” message appears on screen.
• image is gradually dimming or starting to deteriorate.
• Colors appear darker than normal

Prolong the life of the Epson ELPLP38 from 2000 hours to 3000 hours by lowering the Brightness Control to low!

The right type of lamp: Buy authentic

While there are plenty of cheaper options when it comes to buying the Epson ELPLP38 lamp over the Internet, you should go with authentic lamps for a variety of reason.  Start off by looking for the seal of approval displayed by authorized dealers. This certificate proves they have access to original OEM lamps that are created with quality parts.

Most lamps being advertised as “generic” or “compatible” are usually counterfeit lamps with inferior workmanship. While they may appear to bargain, these copycat lamps actually won’t last the full 3000 hours. But even worse, these lamps can damage the sensitive optics in your  Epson PowerLite 1717c because they simply can’t be calibrated properly. Probably the most worrisome feature about these copycat lamps is that due to their toxic materials, they are a health hazard.

Installing a non-OEM Epson ELPLP38 will also void any warranty on your Epson PowerLite 1717c. Learn how to avoid generics posing as authentic lamps.

Buy this lamp on Amazon from the following authorized dealers:

• EPSON ELPLP38 replacement lamp for powerlite 1700c 1705c 1710c 1715c – NEW – Retail – V13H010L38
• EPSON EMP-1705 Replacement Projector Lamp ELPLP38 / V13H010L38

Replacing the lamp

Before installation follow these important safety tips:

• Turn power button off. Wait for the two beeps that follow and unplug the power cord on the Epson PowerLite 1717c.
• Wait until the projector is cool to the touch.
• DO NOT attempt to change the Epson ELPLP38 if the projector is still hot. You get badly burned if you don’t wait for the projector to cool.

IMPORTANT: Do not operate the projector when the lamp is removed as this may result in malfunctions, fire hazard and other accidents.

• Loosen the screw on the Epson PowerLite 1717c projector cover using the screwdriver provided.

• Slide the lamp cover to the side and lift it off the Epson PowerLite 1717c projector.

Loosen the two screws holding the Epson ELPLP38 lamp in place. NOTE: You can only loosen these screws. They don’t come out all the way.

• Grab the two tabs on either side of the the Epson ELPLP38 lamp and slowly pull out the lamp out of the Epson PowerLite 1717c projector.
• Don’t use excessive force or the lamp could break.
• What to do if lamp breaks inside the projector.
• NOTE: The Epson ELPLP38 should not be thrown into the regular garden and needs to be properly recycled.

• Gently insert the new Epson ELPLP38 lamp into the Epson PowerLite 1717c projector.
• Avoid touching the actual lamp since your fingerprints will cause black out spots to appear when the projector starts working.
• Push down the corner marked PUSH until the lamp snaps in.
• Once the Epson ELPLP38 lamp is fully inserted, tighten the screws.
• Slide out the air filters found at the bottom of the projector. Remove the current filter.
• Slide in the new air filter until it clicks into place.
• You are now ready to reset the lamp timer.

Resetting the Epson PowerLite 1717c Lamp Timer

It’s important to reset the PowerLite 1717c has a lamp timer each time a new lamp is installed so the projector can accurately track the Epson ELPLP38 lamp. Never use the Epson ELPLP38 lamp beyond its recommended usage as this can damage the Epson 1717c projector beyond repair.

• Press MENU.
• Scroll down to RESET. Press ENTER.
• Scroll down RESET LAMP HOURS. Press ENTER.
• A second prompt screen will appear. Select YES at the prompt screen. Press ENTER.
• Press ESC or MENU to exit.

Extending the life of your Epson ELPLP38 lamp

Follow this simple tips to make your Epson ELPLP38 lamp last even longer:

• Keep your air filters clean to avoid overheating the projector and causing the lamp to overheat.
• Turn off the Epson PowerLite 1717c projector for at least one hour ever 24 hours.
• Don’t overuse the lamp. An average use of four to five hours per day will ensure longer lamp life.
• Make sure there is enough airflow around the projector particularly if it’s been permanently mounted so it doesn’t overheat.
• Set the Brightness Mode to low.
• Learn more with Top tips for extending DLP projector lamp life

The post Changing the Epson PowerLite 1717c projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Know when to replace the Epson EMP-1715c projector lamp and where to find the best lamp.

STEP 1: End of life warnings

When the Epson ELPLP38 is approaching end of life you’ll start to see the lamp flashing orange and a “Replace the lamp” message will appear on screen. You may also notice that the image is gradually dimming or starting to deteriorate. Colors that appear darker than normal are also an indication of end of life for the Epson ELPLP38. Re the Epson ELPLP38 lamp immediately so you don’t run the risk of having the lamp explode in the Epson PowerLite 1715c projector.

Prolong the life of the Epson ELPLP38 projector lamp from 2000 hours to 3000 hours by lowering the Brightness Control to low!

STEP 2: Buy authentic

There are plenty of companies selling the Epson ELPLP38 projector lamp over the Internet. However, you shouldn’t go with the cheapest lamp since these are not the best Epson ELPLP38 for your Epson PowerLite 1715c. Start off by looking for the seal of approval that authorized dealers display. They have access to the original OEM lamps that are the best product for your Epson PowerLite 1715c projector.

Lamps advertised as “generic, compatible” have inferior workmanship which translates to an inferior product — one that doesn’t last the full 3000 hours. These lamps can’t be calibrated properly and they they can seriously damage the optics in your Epson PowerLite 1715c as well as posing a health hazard due to their toxic materials.

Keep the warranty valid on Epson PowerLite 1715c, stay safe and buy authentic? Learn how to avoid generics posing as authentic lamps.

Buy this lamp on Amazon from the following authorized dealers:

• EPSON ELPLP38 replacement lamp for powerlite 1700c 1705c 1710c 1715c – NEW – Retail – V13H010L38
• EPSON EMP-1705 Replacement Projector Lamp ELPLP38 / V13H010L38

STEP 3: Replacing the Epson ELPLP38 lamp

Before installation follow these important safety tips:

• Turn power button off and after the Epson PowerLite 1715c has beeped twice unplug the power cord.
• The Epson PowerLite 1715c should be cool to the touch.
• DO NOT attempt to change the Epson ELPLP38 projector lamp if the projector is still hot. You get badly burned if you don’t wait for the projector to cool.

IMPORTANT: Do not operate the projector when the lamp is removed as this may result in malfunctions, fire hazard and other accidents.

• Loosen the screw on the Epson PowerLite 1715c projector cover using the screwdriver provided

• Slide the lamp cover to the side and lift it off the Epson PowerLite 1715c projector.

Loosen the two screws holding the Epson ELPLP38 projector lamp in place. These screws don’t come out all the way.

• Grab the two tabs on either side of the the Epson ELPLP38 projector lamp and slowly pull out the lamp out of the Epson PowerLite 1715c projector.
• Don’t use excessive force or the lamp could break.
• What to do if lamp breaks inside the projector.
• NOTE: The Epson ELPLP38 projector lamp should not be thrown into the regular garden and needs to be properly recycled.
• Avoid touching the actual lamp since your fingerprints will cause black out spots to appear when the projector starts working.
• Push down the corner marked PUSH until the lamp snaps in.
• Once the Epson ELPLP38 lamp is fully inserted, tighten the screws.
• Slide out the air filters found at the bottom of the projector. Remove the current filter.
• Slide in the new air filter until it clicks into place.
• You are now ready to reset the lamp timer.

Resetting the Epson PowerLite 1715c Lamp Timer

It’s important to reset the PowerLite 1715c has a lamp timer each time a new lamp is installed so the projector can accurately track the Epson ELPLP38 lamp. Never use the Epson ELPLP38 lamp beyond its recommended usage as this can damage the Epson 1715cprojector beyond repair.

• Press MENU.
• Scroll down to RESET. Press ENTER.
• Scroll down RESET LAMP HOURS. Press ENTER.
• A second prompt screen will appear. Select YES at the prompt screen. Press ENTER.
• Press ESC or MENU to exit.

Extending the life of your Epson ELPLP38 lamp

Follow this simple tips to make your Epson ELPLP38 lamp last even longer:

• Keep your air filters clean to avoid overheating the projector.
• Turn off the Epson PowerLite 1715c projector and let it stand for at least one hour ever 24 hours.
• An average use of four to five hours per day will ensure longer lamp life.
• Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
• Set the Brightness Mode to low.
• Learn more with Top tips for extending DLP projector lamp life

The post How to replace the Epson EMP-1715c projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

The Epson PowerLite 1705c projector lamp will last up to 2000 hours when the Brightness Control is set to High. A low Brightness Control will give you the full 3000 hours.

End of life warning signs

When you notice any of the following sign replace the Epson ELPLP38 immediately:

• A image that is gradually dimming or deteriorating.
• Colour that appears darker than normal or off colour.
• “Replace the lamp” warning flashing on the Epson PowerLite 1705c screen.
• Lamp light flashing a steady orange.

Don’t wait to replace the Epson ELPLP38 lamp!

Go with authentic lamps

It can be tempting to simply buy the first Epson ELPLP38 you come across, especially if it has a bargain prices. The chances are those lamps with the low prices are counterfeit generic lamps. These lamps are inferior products that can’t offer the same quality, consistency and reliability as authentic lamps.

Generic lamps have six main problems:

• inferior workmanship which translates to an inferior product
• they can’t last the full 3000 hours
• can’t be calibrated properly so can seriously damage the optics in your Epson PowerLite 1705c.
• present a health hazard due to their toxic materials.
• installing a generic lamp will void the warranty on the Epson PowerLite 1705c.
• offer no guarantee, technical or customer service even after the lamp has been purchased.

Buy an authentic lamp from a recognized dealer who proudly displays the seal of approval. Read about how generics posing as authentic lamps.

Buy this lamp on Amazon from the following authorized dealers:

• EPSON ELPLP38 replacement lamp for powerlite 1700c 1705c 1710c 1715c – NEW – Retail – V13H010L38
• EPSON EMP-1705 Replacement Projector Lamp ELPLP38 / V13H010L38

Replacing the Epson ELPLP38 lamp

Before installation follow these important safety tips:

• Turn the Epson PowerLite 1705c off.
• After the machine has beeped twice, unplug the power cord.
• Wait until the Epson PowerLite 1705c is cool to the touch before attempting to change the Epson ELPLP38.
• DO NOT attempt to change the  if the projector is still hot. You get badly burned if you don’t wait for the projector to cool.

IMPORTANT: Do not operate the projector when the lamp is removed as this may result in malfunctions, fire hazard and other accidents.

• Loosen the screw on the Epson PowerLite 1705c projector cover using the screwdriver provided.

• Slide the lamp cover to the side and lift it off the Epson PowerLite 1705c projector.

Loosen the two screws holding the Epson ELPLP38 lamp in place. These screws don’t come out all the way.

• Grab the two tabs on either side of the the Epson ELPLP38 lamp and slowly pull out the lamp out of the Epson PowerLite 1705c projector.
• Don’t use excessive force or the lamp could break.
• What to do if a lamp breaks inside the projector.

• NOTE: The Epson ELPLP38 should not be thrown into the regular garden and needs to be properly recycled. Contact your authentic manufacturer and they can assist you in getting the lamp to the right recycling facility.

• Gently insert the new Epson ELPLP38 lamp into the Epson PowerLite 1705c projector.
• Avoid touching the actual lamp since your fingerprints will cause black out spots to appear when the projector starts working.
• Push down the corner marked PUSH until the lamp snaps in.
• Once the Epson ELPLP38 lamp is fully inserted, tighten the screws.
• Slide out the air filters found at the bottom of the projector. Remove the current filter.
• Slide in the new air filter until it clicks into place.

Resetting the Epson PowerLite 1705c Lamp Timer

It’s important to reset the PowerLite 1705c has a lamp timer each time a new lamp is installed so the projector can accurately track the Epson ELPLP38 lamp. Never use the Epson ELPLP38 lamp beyond its recommended usage as this can damage the Epson 1705c projector beyond repair.

• Press MENU.
• Scroll down to RESET. Press ENTER.
• Scroll down RESET LAMP HOURS. Press ENTER.
• A second prompt screen will appear. Select YES at the prompt screen. Press ENTER.
• Press ESC or MENU to exit.

Extending the life of your Epson ELPLP38 lamp

Follow this simple tips to make your Epson ELPLP38 lamp last even longer:

• Keep your air filters clean to avoid overheating the projector.
• Turn off the Epson PowerLite 1705c projector and let it stand for at least one hour ever 24 hours.
• An average use of four to five hours per day will ensure longer lamp life.
• Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
• Set the Brightness Mode to low.
• Learn more with Top tips for extending DLP projector lamp life

The post How to install a Epson PowerLite 1705c projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.