The best investment you can make to keep your Mitsubishi WD-62525 TV working at its best is to buy an authentic TV projector lamp.

Replacing the projector lamp

If you notice the picture is dimming or the color brightness change, it’s time to replace the projector TV lamp. Be sure to buy an authentic lamp from an authorized dealer to keep your TV working. Knock-off counterfeit lamps have a shorter lamp life and have been created with toxic substitutes and are prone to explosions that s often damage the sensitive electronics in your projectors. Invest in authentic.

Find this lamp sold by these authorized dealers on Amazon:

• Lutema 915P020010-E Mitsubishi 915P020010 915P020A10 Replacement DLP/LCD Projection TV Lamp (Economy)
• MITSUBISHI WD-62525 TV Replacement Lamp with Housing
• Mitsubishi WD-62525 TV Assembly with High Quality Original Bulb Inside
  

Changing the projector lamp

Your Mitsubishi WD-62525 TV uses the 915P020010 TV projector lamp. Before replacing the projector lamp, please follow these safety precautions.

• Reduce the risk of electrical shock by disconnecting the power cord on the Mitsubishi WD-62525 TV
• Reduce the risk of severe burns by allowing the TV to cool for at least 45 minutes. It should be cool to the touch.

Replacing the Lamp Cartridge

Tool needed: Phillips screwdriver
1. Turn the television off and unplug the AC cord.
2. Remove the front speaker grill by gently pulling on each side. The grill will snap out.

3. Using a phillips screwdriver, remove the three screws (one on the left and two on the right side)
that hold the recessed plastic cover in place.
4. Remove the plastic cover and set aside with the screws.

5. After removing the cover, you will be able to see the lamp cartridge. With the screwdriver, loosen the three screws of the cartridge. The three screws will not completely remove.
6. Gently grasp the metal handle and pull straight out (towards you).
7. Insert the new lamp cartridge securely into the TV. Do not touch the glass surface of the cartridge.
8. With the screwdriver, tighten the screws on the lamp cartridge.
9. Replace the plastic cover and screws.
10. Snap the speaker grill back into place by pushing it into place on each side with the palm of your hand.

Resetting the Lamp Hour Timer

It’s important to only reset the lamp timer when you replace the Lutema 915P020010 projector lamp.

To reset:

• Press the “System/Reset” button on the TV’s control panel. The green LED on the panel will flash for up to 90 seconds.
• Press the “Power” button to turn the TV on when the green LED stops flashing.

Extending the life of the projector lamp:

• Keep your air filters clean to avoid overheating the projector.
• Learn more with Top tips for extending DLP projector lamp life.

The post Replacement Mitsubishi WD-62525 TV projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Need to install a replacement KDS-55A2000 TV Lamp? Let this guide help.

Don’t settle for anything but the best and be sure to an authentic Sony KDS-55A2000 TV. When buying look for the seal of approval — don’t get caught with a counterfeit lamp. They have shorter lamp and are more toxic due to the substitute materials used by counterfeit manufacturers. These lamps often don’t work properly with the sensitive electronics in your projector and are prone to explosions. Keep your projector working properly and invest in an authentic projector lamp.

Warning signs

Your Sony KDS-55A2000 TV lamp should last up to 8000 hours depending in usagfe and the environment it works in. It’s time to replace the TV lamp when the screen becomes darker, or if brightness starts to diminish gradually and the colors look wrong. A message will also appear on screen asking you to replace the lamp and the LAMP LED on the front of the TV starts blinking.

Find this lamp on Amazon sold by these authorized dealers:

• Aurabeam Economy Replacement Lamp for Sony XL-5200 with housing
• XL-5200 Sony KDS-50A2000 TV Lamp

Replacing the lamp

Before installations preparations:

• Unplug the AC power cord on the KDS-55A2000 TV .
• Your Sony KDS-55A2000 uses the Sony XL-5200 Replacement TV Lamp. Before installing the lamp, let the projector cool for at least 40 minutes. It should be cool to the touch. Don’t rush the cooling as these projectors operate using extremely high temperatures and you run the risk of a serious burn.
• _Take the new Sony XL-5200 lamp out of the box.Do not touch the glass portion of the new lamp. Remove the outside lamp cover.Release the two clamps as shown in the illustration below.

• Remove the lamp door.
• Turn the screw counterclockwise and slide the lever to the left.
• Remove the door.

• Pull out the Sony XL-5200 lamp. Hold the indented grooves on the top corners of the lampand pull the lamp straight out. If the lamp is hard to remove, pull the right side of the lamp for additional traction.
• Do not shake the lamp. Vibration can damage the lamp or shorten its life.
• Avoid touching the front glass of a new lamp.
• NOTE: The Sony XL-5200 TV lamp contains mercury and should not be thrown into regular garbage. Recycle this lamp!

• Put the new Sony XL-5200 lamp into its place.
• Insert the new lamp by pressing the two parts firmly into.
• Make sure the lamp is securely mounted into the compartment. Failure to do so may cause a fire or the screen to go dark.

• The lamp compartment should be properly tilted (see the illustration) in order for the installation to be aligned.
• If the lamp is not securely reattached, the self-diagnostic function may be triggered and the POWER LED blinks three times. Re-insert the lamp if this happens.

• Reattach the lamp door.
• Replace the door by inserting the two tabs in the slot from the left side.
• Slide the lever to the right and then turn the screw clockwise to secure the door.
• Put the outside lamp cover back in its place.
• Replace the cover, inserting it from the left side.
• Press the two tabs on the right side to secure the cover.

You are now ready to reset the TV lamp timer.

Resetting the lamp timer

Turn on the Sony KDS-55A2000 TV and set the Lamp Replacement option in the Setup settings. This setting is necessary to inform you when the next lamp replacement is needed. Until you set the Lamp Replacement option, a message announcing that the lamp is at the end of its life will appear every time you turn on the TV.

• • Press MENU.

• Select Set up. Press enter
• Scroll down to select Clock/Timers
• Reset the lamp timer. Press enter.
• To exit the Settings, press MENU.

The post How to replace the KDS-55A2000 TV Lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Replace the Sony KDS-50A2000 TV Lamp using this guide

Don’t settle for anything but the best and be sure to an authentic Sony KDS-50A2000 TV. When buying look for the seal of approval — don’t get caught with a counterfeit lamp. They have shorter lamp and are more toxic due to the substitute materials used by counterfeit manufacturers. These lamps often don’t work properly with the sensitive electronics in your projector and are prone to explosions. Keep your projector working properly and invest in an authentic projector lamp.

Warning signs

Your Sony KDS-50A2000 TV lamp should last up to 8000 hours depending in usagfe and the environment it works in. It’s time to replace the TV lamp when the screen becomes darker, or if brightness starts to diminish gradually and the colors look wrong. A message will also appear on screen asking you to replace the lamp and the LAMP LED on the front of the TV starts blinking.

Find this lamp on Amazon sold by these authorized dealers:

• Aurabeam Economy Replacement Lamp for Sony XL-5200 with housing
• XL-5200 Sony KDS-50A2000 TV Lamp

Replacing the lamp

Before installations preparations:

• Unplug the AC power cord on the KDS-50A2000 TV .
• Your Sony KDS-50A2000 uses the Sony XL-5200 Replacement TV Lamp. Before installing the lamp, let the projector cool for at least 40 minutes. It should be cool to the touch. Don’t rush the cooling as these projectors operate using extremely high temperatures and you run the risk of a serious burn.
• _Take the new Sony XL-5200 lamp out of the box.Do not touch the glass portion of the new lamp. Remove the outside lamp cover.Release the two clamps as shown in the illustration below.

• Remove the lamp door.
• Turn the screw counterclockwise and slide the lever to the left.
• Remove the door.

• Pull out the Sony XL-5200 lamp. Hold the indented grooves on the top corners of the lampand pull the lamp straight out. If the lamp is hard to remove, pull the right side of the lamp for additional traction.
• Do not shake the lamp. Vibration can damage the lamp or shorten its life.
• Avoid touching the front glass of a new lamp.
• NOTE: The Sony XL-5200 TV lamp contains mercury and should not be thrown into regular garbage. Recycle this lamp!

• Put the new Sony XL-5200 lamp into its place.
• Insert the new lamp by pressing the two parts firmly into.
• Make sure the lamp is securely mounted into the compartment. Failure to do so may cause a fire or the screen to go dark.

• The lamp compartment should be properly tilted (see the illustration) in order for the installation to be aligned.
• If the lamp is not securely reattached, the self-diagnostic function may be triggered and the POWER LED blinks three times. Re-insert the lamp if this happens.

• Reattach the lamp door.
• Replace the door by inserting the two tabs in the slot from the left side.
• Slide the lever to the right and then turn the screw clockwise to secure the door.
• Put the outside lamp cover back in its place.
• Replace the cover, inserting it from the left side.
• Press the two tabs on the right side to secure the cover.

You are now ready to reset the TV lamp timer.

Resetting the lamp timer

Turn on the TV and set the Lamp Replacement option in the Setup settings. This setting is necessary to inform you when the next lamp replacement is needed. Until you set the Lamp Replacement option, a message announcing that the lamp is at the end of its life will appear every time you turn on the TV.

• Press MENU.
• Select Set up. Press enter
• Scroll down to select Clock/Timers
• Reset the lamp timer. Press enter.
• To exit the Settings, press MENU.

The post Replacing the KDS-50A2000 TV Lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Don’t settle for anything but the best and be sure to an authentic  Sony KDS-60A2000 TV. When buying look for the seal of approval — don’t get caught with a counterfeit lamp. They have shorter lamp and are more toxic due to the substitute materials used by counterfeit manufacturers. These lamps often don’t work properly with the sensitive electronics in your projector and are prone to explosions. Keep your projector working properly and invest in an authentic projector lamp.

Warning signs

Your Sony KDS-60A2000 TV lamp should last up to 8000 hours depending in usagfe and the environment it works in. It’s time to replace the TV lamp when the screen becomes darker, or if brightness starts to diminish gradually and the colors look wrong. A message will also appear on screen asking you to replace the lamp and the LAMP LED on the front of the TV starts blinking.

Find this lamp on Amazon sold by these authorized dealers:

• Aurabeam Economy Replacement Lamp for Sony XL-5200 with housing
• Philips Sony KDS-60A3000 KDS60A3000 Lamp with Housing XL5200
• XL-5200 Sony KDS-60A2000 TV Lamp
  

Replacing the lamp

Before installations preparations:

• Unplug the AC power cord on the Sony KDS-60A2000 TV .
• Your Sony KDS-60A2000 uses the Sony XL-5200 Replacement TV Lamp. Before installing the lamp, let the projector cool for at least 40 minutes. It should be cool to the touch. Don’t rush the cooling as these projectors operate using extremely high temperatures and you run the risk of a serious burn.
•  _Take the new Sony XL-5200 lamp out of the box.Do not touch the glass portion of the new lamp. Remove the outside lamp cover.Release the two clamps as shown in the illustration below.

• Remove the lamp door.
• Turn the screw counterclockwise and slide the lever to the left.
• Remove the door.

• Pull out the Sony XL-5200 lamp. Hold the indented grooves on the top corners of the lampand pull the lamp straight out. If the lamp is hard to remove, pull the right side of the lamp for additional traction.
• Do not shake the lamp. Vibration can damage the lamp or shorten its life.
• Avoid touching the front glass of a new lamp.
• NOTE: The Sony XL-5200 TV lamp contains mercury and should not be thrown into regular garbage. Recycle this lamp!

• Put the new Sony XL-5200 lamp into its place.
• Insert the new lamp by pressing the two parts firmly into.
• Make sure the lamp is securely mounted into the compartment. Failure to do so may cause a fire or the screen to go dark.

• The lamp compartment should be properly tilted (see the illustration) in order for the installation to be aligned.
• If the lamp is not securely reattached, the self-diagnostic function may be triggered and the POWER LED blinks three times. Re-insert the lamp if this happens.

• Reattach the lamp door.
• Replace the door by inserting the two tabs in the slot from the left side.
• Slide the lever to the right and then turn the screw clockwise to secure the door.
• Put the outside lamp cover back in its place.
• Replace the cover, inserting it from the left side.
• Press the two tabs on the right side to secure the cover.

You are now ready to reset the TV lamp timer.

Resetting the lamp timer

Turn on the TV and set the Lamp Replacement option in the Setup settings. This setting is necessary to inform you when the next lamp replacement is needed. Until you set the Lamp Replacement option, a message announcing that the lamp is at the end of its life will appear every time you turn on the TV.

• Press MENU.
• Select Set up. Press enter
• Scroll down to select Clock/Timers
• Reset the lamp timer. Press enter.
• To exit the Settings, press MENU.

The post Install a new Sony KDS-60A2000 TV lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

When it’s time to replace the Mitsubishi WD-62827 TV Lamp follow this guide.

The best investment you can make is to invest in an authentic Mitsubishi WD-62827 TV Lamp. Knock-off counterfeit lamps have a shorter lamp life and have been created with toxic substitutes and are prone to explosions that s often damage the sensitive electronics in your projectors. Invest in authentic. The Mitsubishi WD-62827 TV uses the Mitsubishi 915P027010 Replacement TV Lamp.

Buy this lamp on Amazon from the following retailers:

• AuraBeam Economy Replacement Television Lamp for Mitsubishi WD-62827 with Housing
• Mitsubishi WD-62827 150 Watt TV Lamp Replacement by Powerwarehouse
• Lutema 915P027010-PI Mitsubishi 915P027010 915P027A10 Replacement DLP/LCD Projection TV Lamp – Philips Inside
  

Warning

When the Mitsubishi WD-62827 TV Lamp is approaching end if life, the TV displays a warning message for one minute when you power on the TV. The message will reappear the next five times you turn on the TV. Change the Mitsubishi WD-62827 TV Lamp immediately.

Replacing the projector lamp

Before replacing the projector lamp, please follow these safety precautions.

• Reduce the risk of electrical shock by disconnecting the power cord on the Mitsubishi WD-62827 TV
• Reduce the risk of severe burns by allowing the TV to cool for at least 45 minutes. It should be cool to the touch.

After the lamp has cooled, remove the plastic air exhaust grille/cover by removing two screws with a large Phillips screwdriver.

• • With a large flat-blade screwdriver, loosen the three shiny screws securing the Mitsubishi 915P027010 Replacement TV  lamp in place.
  • Open the plastic bag that came with the new lamp.
  • Grasp the wire handle of the lamp cartridge and pull if out straight.
  • CAUTION: Do not tilt or rotate the cartridge, as small glass fragments may fall out. Without tilting or putting down the lamp cartridge, insert it into the opened bag.
  • Close the bag while being careful that no glass particles fall out.Note: The used Mitsubishi 915P027010  lamp contains mercury and should be properly recycled. Don’t throw it into regular garbage. Please recycle this lamp.
    

• Insert the new Mitsubishi 915P027010 Replacement TV  lamp in the same orientation as the old cartridge.
• Do not touch the glass parts of the new lamp cartridge. Push on the cartridge housing until it is fully seated.
• Tighten the three screws. AVOID OVERTIGHTENING!
• Replace the plastic grille/cover and tighten screws.

The post Replace the Mitsubishi WD-62827 TV Lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Follow these instructions when it’s time to replace the Samsung HL-P6163W TV lamp

When the Samsung HL-P6163W TV lamp is reaching end of life you may notice all three LEDs on the front panel — Timer, Lamp, & Temp — are flashing. Colors may appear flattened and the brightness on the screen may be diminished.

Keep it authentic

The Samsung HL-P6163W TV lamp uses the Samsung HL-P6163W TV Replacement TV Lamp. Reduce hassles by always buying authentic. Counterfeits have several chronic problems including:

• shorter lamp life than original lamps
• created with toxic materials and carcinogenic parts including Krypton-85
• prone to explosions
• can damage the sensitive electronics in your projector
• when you buy copy-cat lamps you get no guarantee or refunds
• installing a generic lamp can void your warranty.

Find this lamp sold on Amazon by these authorized dealers:

• • FI Lamps for BP96-00826A Samsung HL-P6163W TV Lamp
  • Samsung HL-P6163W TV Assembly Cage with High Quality Projector bulb

• • Replacing the lamp

    Before replacing the lamp allow the Samsung HL-P6163W TV to cool down for one hour. There is a risk of a serious burn if the TV is not completely cool. Be sure to unplug the TV from the electrical socket. Before replacing the lamp allow the Samsung HL-P6163W TV to cool down for one hour. There is a risk of a serious burn if the TV is not completely cool. Be sure to unplug the TV from the electrical socket.

    

    Step 1: Use a screwdriver to remove the screw holding the TV lamp cover in place.

     

    

    Step 2: Remove the Lamp cover.

     

    

    Step 3: Using a screwdriver loosen the screws securing the HL-P6163W in place

     

    

    Step 4: Separate the Lamp from the engine by holding the handle and pulling it out.

    NOTE: The contains mercury. Please recycle this lamp. Don’t throw it into conventional garbage. 

    Inserting the new lamp

    • • • Insert the new Samsung HL-P6163W TV Replacement TV Lamp
        • Tighten the two screws on the lamp.
        • Replace the lamp cover and tighten the screws. NOTE: Be sure to tighten the lamp cover on the TV after changing the lamp. Note that the TV will not function if the lamp cover is not securely attached. Please tighten the holding screw on the lamp cover after it has been attached to the TV.

    If any there is no picture or a very dark picture or if the TV won’t turn on, repeats the steps again to ensure the lamp has been installed properly and the lamp door has been re-installed correctly. If any there is no picture or a very dark picture or if the TV won’t turn on, repeats the steps again to ensure the lamp has been installed properly and the lamp door has been re-installed correctly.

    Extend the life of the Samsung HL-P6163W TV Replacement TV Lamp by following these tips.

The post Samsung HL-P6163W TV Lamp Replacement appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

When the Toshiba 50HM66 TV lamp is reaching end of life the picture darkens and the colors fade. The LED indicator lamp will also stop lighting. If you hear a a loud noise and the picture goes black, replace the lamp immediately.

Buy authentic and be prepared

It may be confusing trying to find the correct TV lamp for your Toshiba 50HM66 TV lamp. Your key for a successful replacement lamp is to always install an OEM authentic TV lamp. Be sure to buy an authentic Toshiba Y66-LMP model.

Copycat lamps have a number of serious issues that include a shorter life and problems with exploding. Since they have been manufactured with toxic substitutes they are a threat to your health and safety. Counterfeits can also damage your TV optics as well as your eyesight. Installing a generic lamp also voids your warranty. Go with authentic.

Find this lamp sold on Amazon by these authorized dealers:

• TOSHIBA Y66-LMP Replacement Phoenix Lamp w/ Housing 6 Month Warranty
• Toshiba Y66/Y67-LMP Lamp Replacement Genuine Phoenix Lamp with Housing

Installing the T V lamp

Follow these important safety tips before changing the projector lamp:

• Switch off the TV.
• Disconnect the power cord.
• Allow the Toshiba 50HM66 TV to cool down for at least 30 minutes. If should be cool to the touch. The Toshiba 50HM66 TV operates under high temperatures and you can burn yourself badly if you don’t allow it to cool down.

Loosen the two screws holding the Toshiba Y66-LMP projector lamp in place.

Grasp the lamp unit handle and gently pull the lamp unit straight out of the TV. Set the old lamp unit aside to be properly recycled. These lamps contain mercury and can’t be placed into regular garbage.

Get the new  Toshiba Y66-LMP replacement lamp ready. Carefully insert the new lamp unit straight into the TV until it is fully seated. Using a manual phillips screwdriver, tighten the two Toshiba Y66-LMP lamp unit screws. Note: Hand-tighten only. Do not use an electric screwdriver.

Test the lamp

The post Change the Toshiba 50HM66 TV lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

When to replace?

When the RCA HD50LPW166YX12 TV lamp  is reaching end of life, you will see a message on screen and the lamp indicator on the TV will start flashing. Other end of life signs may also include darker images and colors that look off.

Authentic lamps are critical!

Don’t settle for anything but the best for your RCA HD50LPW166YX12 TV Lamp. When buying look for the seal of approval. This TV uses the RCA 270414 TV Lamp.

6 reasons to avoid generic TV projector lamps:

• shorter lamp life than original lamps
• created with toxic materials and carcinogenic parts including Krypton-85
• prone to explosions
• can damage the sensitive electronics in your projector
• when you buy copy-cat lamps you get no guarantee or refunds
• installing a generic lamp voids your projector’s warranty.

Find this lamp on Amazon sold by these authorized dealers:

• 270414 RCA M50WH185 TV Lamp

Installing the new lamp

NOTE: Avoid touching the bulb to avoid getting any dirt or oil on it. The oil residue can burn black marks into the bulb and cause premature failure. Be sure to do a final wipe with a clean, non-abrasive, lint-free cloth before installing your lamp.

We also recommend replacing the entire enclosure if it looks damaged or warped as this may cause your lamp to be misaligned inside the television!

Tools needed

To replace just your lamp, all you need is:

• An RCA DLP lamp made by Philips
• A flat-head screwdriver
• A T-10 & T-15 Torx driver
• A pair of plyiers
• A pair of gloves or a lint-free cloth (to wipe the glass down afterwards)

Step 1: Locate the lamp.

Here is the back of a typical RCA DLP TV… your TV may look slightly different.

The lamp is behind this rectangle door!

You’re going to need your flat-head screwdriver to loosen this screw.

Loosen the screw and then use the two “clips” to open the compartment door.

What we’re looking at it is the RCA 270414 TV Lamp  lamp enclosure. There is one screw on each side that need to be loosened.

Now you can gently pull back the tray and to remove the RCA 270414 TV Lamp.

This is what it should look like pulled straight back…

Step 2: Remove the lamp from the enclosure

With your old RCA 270414 TV Lamp \facing downward visually inspect the area labeled “Clip”  on the top and bottom of the enclosure. Between them, there is about a 3″ gap where you need to push in to be able to pull out the rear lamp cover.

At the other side of the RCA 270414 TV Lamp enclosure while  pushing in on the lamp enclosure, you want to release the side clips.

When disassembled the RCA 270414 TV Lamp bulb should look this wiring.

Unscrew the RCA 270414 TV Lamp connectors with your plyer and torx driver. Once the back of the enclosure is removed. Now you have access to remove the three screws circled above

You should have three parts after taking the RCA 270414 TV Lamp apart.

NOTE: The used RCA 270414 TV Lamp contains mercury and should be properly recycled. Don’t throw it into regular garbage.

Step 3: Installing the new lamp

You are ready to install a new original bulb. Place the bulb into the plastic lamp cage. Tighten the top washer on the RCA 270414 TV Lamp.

Secure the RCA 270414 TV Lamp into the cage by tigthening the side panels.

Place the lamp cover back on the television.

Watch our training video to learn more.

The post Replacing the RCA HD50LPW166YX12 TV Lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

When to replace?

When the Sony KDS-R60XBR2 TV lamp  is reaching end of life, you will see a message on screen and the lamp indicator on the TV will start flashing. Other end of life signs may also include darker images and colors that look off.

The Sony KDS-R60XBR2 TV uses the Original Lamp For SONY KS 70R200A:KDS R70XBR2:KDS R60XBR2:KDS 70R2000 Rear projection TV

Find this lamp on Amazon.

To replace the projector lamp

The Sony KDS-R60XBR2 TV uses the Sony XL-5300 Replacement TV Lamp. Perform there safety steps before installing the new projector lamp:

• Turn off the power on the main unit.
• The cooling fan will continue to operate for two minutes after the power is turned off.
• Wait several minutes before unplugging the power cord.
• Wait an additional 30 minutes to allow the lamp to cool down. The lamp operates under extreme so avoid touching it before changing the lamp.

Remove the outside Sony XL-5300 projector lamp cover. Click the switch open to remove the lamp cover.

Pull out the Sony XL-5300 lamp. Hold the indents on the top and bottom of the lamp, and pull the Sony XL-5300 lamp straight out. Do not touch the inside of the lamp compartment. Never touch the glass portion of the lamp or the surrounding parts.

NOTE: This projector lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!

Put the new Sony XL-5300 lamp into its place and make sure it’s securely mounted into the compartment. Failure to do so may cause a fire or the screen to go dark.

NOTE: The lamp compartment is tilted, as shown in the following illustration. If the Sony XL-5300 lamp is not securely reattached, the self-diagnostic function may be triggered and the POWER LED blinks three times.

Reattach the lamp door. To secure the door, turn the knob to the right while pushing the door in, until the marks on the lid and the and the case line up. Then, turn the screw clockwise to tighten the door.

Reset the Lamp Replacement option

• Press the MENU button on the remote control. Scroll down to the SETUP option.
• Scroll down to the LAMP REPLACEMENT. Press ENTER.
• A prompt appears asking if you want to reset the lamp hours.
• After the lamp is replaced, you must select this option or this message will
  continue to appear when you first turn on the TV.

Authentic lamps are critical!

Don’t settle for anything but the best for your Sony KDS-R60XBR2 TV. When buying look for the seal of approval.

6 reasons to avoid generic LCD projector lamps:

• shorter lamp life than original lamps
• created with toxic materials and carcinogenic parts including Krypton-85
• prone to explosions
• can damage the sensitive electronics in your projector
• when you buy copy-cat lamps you get no guarantee or refunds
• installing a generic lamp voids your projector’s warranty.

Green your Sony XL-5300 TV

If you interested in going green with your KDS-R60XBR2, you can replace only the projector bulb and re-used the plastic casing. This can save your money plus help reduce waste. Watch our training video to learn more.

Find this lamp on Amazon:

The post Replace the Sony KDS-R60XBR2 TV Lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Replace the 4719-001997 DLP chip to fix white dots on your Mitsubishi WD-73642 screen

The white spots on your Mitsubishi WD-73642 are caused by the 4719-001997 DLP chip being worn out. Known as Mitsubishi white death syndrome, this problem can be solved by installing a new Mitsubishi/Toshiba 4719-001997 DLP Chip 1910-6143W.

Note: These instructions can also be used for the following Mitsubishi models: 
WD-57733, WD-57734, WD-57833, WD-60638, WD-60733,WD-60735, WD-60737,WD-60738, WD-60833, WD-60837, WD-60C8,WD-60C9, WD-65638,WD-65731, WD-65733,WD-65734, WD-65735, WD-65736, WD-65737, WD-65738,WD-65833,WD-65835,WD-65837, WD-65838,WD-65C8,WD-65C9, WD-73638, WD-73640, WD-73642, WD-73733, WD-73734, WD-73735, WD-73736,WD-73737, WD-73738, WD-73833, WD-73835,WD-73837,WD-73838, WD-73840, WD-73C11, WD-73C8, WD-73C9, WD-75837, WD-82737, WD-82738, WD-82838, WD-Y657 WD-C657,WD-Y577.

Find this new Mitsubishi/Toshiba 4719-001997 DLP Chip 1910-6143W on Amazon and then follow our step-by-step visual guide.

Equipment needed

• Electric Philips screwdriver
• needle nose pliers or a 5mm nut driver
• antistatic gloves OR plastic gloves used with an antistatic wrist band
• soft cloth or brush

How to replace the 4719-001997 DLP Chip

Step 1

Step 1: Put on the plastic gloves. Loosen all the screws found on the back panel.

Step 2

Step 2: Put the screws to the side. Gently remove the back panel.

Step 3

Step 3: Remove the 3 screws holding the lamp engine in place.

Step 4

Step 4: Disconnect all the connectors. Important: don’t yank any cables.

Step 5

Step 5: Carefully slide the light engine from the cabinet.

Step 6

Step 6: Remove the 3 screws holding the color wheel protective cover in it place. Avoid touching any of the optical components as this can affect the quality of your picture.

Step 7

Step 7: Carefully disconnect the cable between the terminal board and lamp.

Step 8

Step 8: Disconnect the cables connecting the color wheel.

Step 9

Step 9: Loosen the 3 screws holding the cooling unit/fan to the terminal board.

Step 10

Step 10: Remove the cooling unit.

Step 11

Step 11: Loosen the 2 screws holding the terminal cover in place. (Good time to dust this section).

Step 12

Step 12: Loosen the 10 screws holding the terminal in place.

Step 13

Step 13: Carefully pop the terminal out of its holder.

Step 14

Step 14: Unlock the old DLP Chip from the terminal. You may need to loosen the screw on the side or use a flat edged screwdriver to pop it out.

Step 15

Step 15: Place the new DLP chip into place. Handle the DMD DLP CHIP only by the edges because it is very sensitive to antistatic electricity.

Step 16

Step 16: Put the terminal back into its holder.

Step 17

Step 17: Tighten the 10 screws holding the terminal in place.

Step 18

Step 18: Tighten the 2 screws on terminal board’s cover.

Step 19

Step 19: Put the fan unit back on.

Step 20

Step 20: Tighten the 3 screws holding the cooling unit/fan to the terminal board.

Step 21

Step 21: Reconnect the cables connecting the color wheel.

Step 22

Step 22: Reconnect the cable between the terminal board and lamp.

Step 23

Step 23: Replace the color wheel protective cover and tighten the 3 screws.

Step 24

Step 24: Re-connect all the cables running from the terminal board and light engine.

Step 25

Step 25: Carefully place the light engine back inside the unit. Tighten the 3 holding the terminal board and light engine in place.

Step 26

Step 26: Put the back panel back onto the TV.

Step 27

Step 27: Tighten all the screws on the back panel. Enjoy your crisp, clear picture on your Mitsubishi WD-73642 RPTV.

Need to replace the Mitsubishi WD-73642 RPTV lamp? Check out our tutorial. 

Learn more about your Mitsubishi WD-73642 RPTV:

• 7 Tips for extending RPTV lamp life
• RPTV Troubleshooting: TV won’t turn on
• Consumer Alert: The dangers of RPTV generic lamps

The post Fix white dots on your Mitsubishi WD-73642 RPTV with 4719-001997 DLP chip appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.