Our guide shows you how easy it is to replace the Sony VPL-HW20 projector lamp!

Buy authentic

Don’t settle for anything but the best. Buy an authentic  for your Sony VPL-HW20 projector lamp. When buying look for the seal of approval — don’t get caught with a counterfeit lamp. They have shorter lamp and are more toxic due to the substitute materials used by counterfeit manufacturers. These lamps often don’t work properly with the sensitive electronics in your projector and are prone to explosions. Keep your projector working properly and invest in an authentic projector lamp.

Don’t settle for anything but the best for your Sony VPL-HW20 projector and install an authentic projector lamp. Don’t get caught with a counterfeit lamp. Keep your projector working properly and invest in an authentic projector lamp.

Buy this lamp on Amazon from the following verified manufacturers:

• SONY LMP-H201 Lamp manufactured by SONY
• Sony VPL-VW85 Projector Assembly with High Quality Original Bulb Inside
• LMP-H201 Sony HW15 Projector Lamp

When to replace?

When the this Sony VPL-HW20 projector lamp is reaching end of life, the Lamp light will flash red in 3 second intervals. The message “Please replace the Lamp/Filter” will also start flashing on screen. If the projector lamp dims change it immediately. Sony recommends replacing the air filter at the same as replacing the lamp.

Replacing the Sony VPL-HW20 Lamp and Air Filter

Before installations preparations:

• Unplug the AC power cord on the Sony VPL-HW20 projector.
• Your Sony VPL-HW20 projector uses the Sony LMP-H201 projector lamp. Before installing the lamp, let the projector cool for at least 40 minutes. It should be cool to the touch. Don’t rush the cooling as these projectors operate using extremely high temperatures and you run the risk of a serious burn.
• The projector lamp cover is on the bottom of the projector so you will need to turn it over. Put down a soft cloth on a flat surface to prevent the projector getting scratched. Turn the projector over gently. Don’t lean on the projector and make sure the surface is flat and stable.
• Using a Philips screwdriver, loosen the screw holding the projector lamp cover in place. Slide the projector lamp cover. Put it to one side.

Loosen the 3 screws on the Sony LMP-H201 lamp using a Phillips screwdriver. Grab the wire handle on the Sony LMP-H201 projector lamp and gently pull the lamp straight out. Take care not to bang the lamp as you can cause the bulb to break.

NOTE: The Sony LMP-H201 projector lamp contains mercury and should not be thrown into regular garbage. Recycle this lamp!

To finish the projector lamp installation:

• Remove the packaging from the new Sony LMP-H201 projector lamp.
• Lift up the handle and slowly lower the Sony LMP-H201 projector lamp into the projector.
• Push it in securely until it reaches the end.
• Tighten the three screws on the lamp.
• Also don’t touch the actual bulb in the new lamp as oily fingerprints can burn a black spot on the lamp when it heats up.
• Slide the lamp cover back onto the Sony VPL-GH10 projector.
• Close the projector lamp cover and tighten the screws.
  Remember to install the lamp cover properly as the projector will not turn on if the cover is loose or not installed correctly.

Replacing the Sony VPL-GH10 air filter

• Remove the filter holder. The air filter will be inside the holder. Don’t touch the fan inside as this can damage the projector.
• Remove the old Sony VPL-GH10 filter and put it to one side. Attach the new air filter so that is fits into the 10 claws properly on the holder.
• Aligning the air filter with the shape of the filter holder will make it easier to install.
• Be sure to put the air filter holder back into the projector aligned up properly. If not, the projector will not turn back on!
• Wipe off any dust from the ventilation intake holes using a soft cloth. Put the projector back in its original position

Resetting the Sony VPL-GH10 projector lamp timer

• To reset the projector lamp timer, plug the AC power cord back into Sony VPL-GH10 projector.
• Using the remote, scroll down to the Setup Menu.
• Press Enter.

• A Lamp Setting message will appear asking you if the projector lamp has been replaced.
• Click on Yes.
• You will see a confirmation message and the Projector Lamp Timer will be automatically reset to zero.
• See the number of hours left on your lamp by going to the Information Menu

You can extend the life of the Sony LMP-H201 projector lamp by always making sure the filter is clean and there is enough airflow around the projector. Learn how to get a longer projector lamp life with top tips for extending DLP projector lamp life.

4 reasons to avoid counterfeit lamps:

• shorter lamp life
• toxic due to the substitute materials used by counterfeit manufacturers.
• won’t work properly with the sensitive electronics in your projector
• prone to explosions

The post Install a new Sony VPL-HW20 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Cleaning the Air Filter and Vents

Clean the projector’s air filter or vents if they get dusty, or if you see a message telling you to clean them.

• • 1. Turn off the projector and unplug the power cord.
    2. Gently remove the dust using a small vacuum designed for computers or a very soft brush (such as a paintbrush).Note: You can remove the air filter so you can clean both sides of it. Do not rinse the air filter in water, or use any detergent or solvent to clean it.Caution:
       Do not use canned air. The gases may leave a flammable residue or push dust and debris into the projector’s optics or other sensitive areas.
    3. If dust is difficult to remove or the air filter is damaged, replace the air filter.

Replacing the Air Filter

• You need to replace the air filter in the following situations:
  • • After cleaning the air filter, you see a message telling you to clean or replace it
    • The air filter is torn or damaged

You can replace the air filter while the projector is mounted to the ceiling or placed on a table.

• 1. Turn off the projector and unplug the power cord.
  2. Carefully open the air filter cover.
     
  3. Pull the air filter out of the projector.
     
     Note: Air filters contain ABS resin and polyurethane foam. Dispose of used air filters according to local regulations.
  4. Place the new air filter in the projector as shown and push gently until it clicks into place.
     
  5. Close the air filter cover.

Need to replace the Epson EX7220 projector lamp? Follow our guide.

The post Replacing the Epson EX7220 air filter appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Start off with authentic

Save yourself unnecessary headaches and purchase an authentic BenQ HT1075 projector lamp. Avoid counterfeit lamps.

You’ll need model BenQ 5J.J9H05.001 replacement lamp.

Find this lamp on Amazon from the following authorized dealers:

• • BenQ 5J.J9H05.001 REPLACEMENT LAMPS HT1075 HT1085ST
  • 5J.J9H05.001 Replacement Lamp for Projectors
    

Why go authentic? Counterfeit “compatible” lamps may appear to be a bargain but in the long run end up costing more due to their shorter lamp life. They are prone to explosions and can put your eyesight at risk. Due to their substitute toxic materials and carcinogenic parts, the few dollars you will save are not worth it. Protect your health and keep your BenQ HT1075 working at optimum levels. Go with an authentic projector lamp.

End of life warning signs

Your BenQ HT1075 projector uses the BenQ 5J.J9H05.001 replacement projector lamp. When it’s time to replace the BenQ HT1075 projector lamp you’ll see a series warnings appear on screen.

First warning: Install a new lamp for optimal performance. If the projector operates normally in Economic mode you may continue operating the
projector until the next hour lamp warning appears.
Press OK to dismiss the message.

Second Warning: Strongly recommend you to replace the lamp at this stage. The BenQ 5J.J9H05.001 lamp brightness
diminishes with use. This is normal lamp behavior. You can
replace the lamp whenever you notice that the brightness
level has significantly diminished.
Press OK to dismiss the message.

Final warning: The lamp MUST be replaced before the projector will operate normally.
Press OK to dismiss the message.

Follow these safety instructions before changing the lamp:

• • • Reduce the risk of electrical shock by disconnecting the power cord on the BenQ HT1075 projector.
    • Reduce the risk of severe burns by allowing the projector to cool for at least 45 minutes. The projector should be cool to the touch.

Replacing the projector lamp

The projector lamp cover is found on the side of the BenQ HT1075 projector.
Loosen the screw holding the projector lamp cover in place

Lift up the projector lamp cover. Put it to one side.

NOTE: The BenQ 5J.J9H05.001 projector lamp contains mercury and should not be thrown into regular garbage. It should be properly recycled. 

Loosen the screws that secures the lamp. Lift the handle so that it stands up.

Use the handle to slowly pull the lamp out of the projector. Pulling it too quickly may cause the lamp to break and scatter  broken glass in the projector.

Insert the new BenQ 5J.J9H05.001 lamp into the projector taking care not to touch the actual bulb.

Tighten the screws on the new lamp Loose screw may cause a bad connection, which could result in malfunction. Do not over tighten the screw.

Replace the lamp cover on the BenQ HT1075 projector. You are know ready to reset the lamp timer.

Resetting the lamp timer

After changing the lamp, you’ll need to rese the lamp timer. Do not reset if the lamp is not new or replaced as this could cause damage.

• After the startup logo displays, resetting the lamp timer via the OSD menu.
  Under the Advanced OSD menu, go to System Setup : Advanced > Reset Lamp Timer/
• Select RESET.
• • Under the Basic OSD menu, if there’s no signal connected to the projector, go to Reset Lamp
  Timer and select Reset
• If there are signals connected, go to Settings > Reset Lamp Timer and select Reset.
• A “Reset Successfully” message displays to notify that the lamp time has been reset to “0”

• Learn more with Top tips for extending DLP projector lamp life.

The post Replacing the BenQ HT1075 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

Replacing the lamp

Follow these important safety instructions before installing the new NEC LT260 projector lamp

• • • turn off the projector.
    • unplug the projector from its power source.
    • unplug the power cable.
    • wait until the projector is cool to the touch to avoid getting burned.

Loosen the lamp cover screw. It is not removeable so you will know it’s fully loose when the screwdriver goes into a freewheeling condition. Remove the lamp cover.

Loosen the two screws keeping the NEC LT60LPK lamp housing secure. These screws are also non-removeable so you will know when they have been loosened when the screwdriver stars freewheeling.

Remove the NEC LT60LPK lamp by pulling out the handle.

The post Install a replacement NEC LT260 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

The best investment you can make is to invest in an authentic Mitsubishi LVP SA51UX projector lamp. Knock-off counterfeit lamps have a shorter lamp life and have been created with toxic substitutes and are prone to explosions that s often damage the sensitive electronics in your projectors. Invest in authentic. This Mitsubishi LVP SA51UX projector uses the  Mitsubishi VLT-PX1LP model.

Buy this lamp on Amazon from the following retailers:

• MITSUBISHI VLT-PX1LP Projector Replacement Lamp with Housing
• SpArc Platinum for Mitsubishi VLT-PX1LP Projector Replacement Lamp with Housing
• Lutema VLT-PX1LP-P01-1 Mitsubishi LCD/DLP Projector Lamp (Philips Inside)

Warning

Replacing the projector lamp

Before replacing the projector lamp, please follow these safety precautions.

• Reduce the risk of electrical shock by disconnecting the power cord on the Mitsubishi LVP SA51UX projector.
• Reduce the risk of severe burns by allowing the projector to cool for at least 45 minutes. It should be cool to the touch.

Remove the lamp cover in the direction of the arrow as indicated. Loosen the two screws on the Mitsubishi VLT-PX1LP  lamps (a). Pull up the handle.

Resetting the Lamp Hour Timer

It’s important to only reset the lamp timer when the Mitsubishi LVP SA51UX lamp has been replaced. Resetting the projector lamp timer without changing the lamp can make it work beyond its recommended hours and cause harm to your projector.

To reset the lamp operation time

• Plug in the power cord
• Reset the lamp operation time by holding down the ARROW key and the POWER button on the control panel at the same time.
• Make sure that the STATUS indicator blinks twice and the lamp operation time is reset successfully.
• IMPORTANT: Unless these three buttons are pressed at the same time, the lamp operation time isn’t reset.

Extending the life of the projector lamp:

• Keep your air filters clean to avoid overheating the projector.
• Learn more with Top tips for extending DLP projector lamp life.

The post Changing the Mitsubishi LVP SA51UX projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

When the Optoma DH1011 projector lamp approaches end of life, a replacement message will flash on screen. You may also notice the picture quality starting to have poor resolution with washed out colors. Change your projector lamp immediately. The projector will not work if the lamp has burnt out or broken.

Buying the right lamp

Your Optoma HD25 projector uses the Optoma BL-FU240A.

• Buy this lamp on Amazon from the following authorized dealers:

  • Optoma BL-FU240A Projector Housing with Genuine Original Osram P-VIP Bulb
  • Optoma BL-FU240A, UHP, 240W Projector Lamp
  • BL-FU240A Optoma Projector Lamp Replacement with cage assembly. Projector Lamp Assembly with High Quality Genuine Original Osram PVIP Bulb Inside.

  If you are buying over the Internet, avoid projector lamps with a low price tag for the following reasons:

• counterfeit lamps have half the life span of original lamps
• created toxic materials that can damage your health
• prone to explosions
• damage the sensitive electronics in your projectors
• when you buy copy-cat lamps you get no guarantee or refunds
• installing a generic lamp voids your projector’s warranty.

Learn 7 ways to spot a counterfeit projector lamp.

Installing the Optoma HD25 lamp

Before replacing the Optoma BL-FU24 follow these important safety tips:

• Switch off the power to the Optoma HD25 projector by pressing the Power/Standby button.
• Disconnect the power cord.
• Allow the projector to cool down for at least 30 minutes. If should be cool to the touch. These projectors run using high temperatures and you can burn yourself badly if you don’t allow the projector to cool down.

1. Use a screwdriver to undo the two screws holding the lamp cover in place. The screws on the lamp cover and the lamp cannot be removed.

2. Remove the lid and place to one side. Don’t lose the lid as the Optoma HD25 projector will not turn back on until the lamp cover has been properly installed.

3. Remove the two screws holding the Optoma BL-FU24 in place.

Note: The used Optoma BL-FU24 lamp contains mercury and should be properly recycled. Don’t throw it into regular garbage. Please recycle this lamp.

4. Lift up the wire handle on the Optoma BL-FU24 lamp and slowly remove it from the projector.

Be careful not to bang the lamp against the projector as this may case the bulb to break. Learn how to clean up a broken lamp.

5. Remove the new Optoma BL-FU24 from its packaging. Taking care not to touch the actual bulb, lift up the handle on the new lamp and insert it gently into the Optoma HD25 projector.

6. Tighten the two screws on the lamp.

7. Replace the lamp cover and tighten its two screws. You are now ready to reset the Lamp Replacement Timer.

Reset the Lamp Replacement Timer

The Optoma HD25 projector has an automatic lamp timer that tracks the numbers of hours left in the lamp. If you don’t reset the lamp replacement timer you run the risk of the lamp being used beyond its recommended life and possibly exploding in the projector.

To reset the Lamp Replacement Timer:

• Turn on the projector.
• Press MENU.
• Select OPTIONS.
• Select Lamp Settings.
• Select Lamp Reset.
• Select Yes.
• Press MENU to exit.

Tips for extending projector lamp life:

• Keep your air filters clean to avoid overheating the projector.
• Every 24 hours, turn off the projector and let it stand for 1 hour
• Make sure there is enough airflow around the Optoma HD25 projector particularly if it’s been permanently mounted.
• Learn more with Top tips for extending DLP projector lamp life

The post Replacing the Optoma HD25 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

When it’s time to replace the Canon LV-WX300 projector lamp you’ll see a lamp replacement icon appear on screen and the LAMP REPLACE indicator will light orange. Replace the lamp immediately. When the projector is in operation, the duration (in hours) of lamp usage is automatically calculated by the built-in timer.

Buy this lamp on Amazon sold by these authorized dealers:

• Canon 0119C001
• Canon LV-LP39
  

Watch for the warning signs on screen:

First warning: The lamp has been in operation for 4500 hours. Install a new lamp

Second warning: The lamp has been in operation for 4950 hours. Get your authentic replacement projector lamp ready .

Install the projector lamp

Your Canon LV-WX300 projector uses the Canon LV-LP39 projector lamp model. Before replacing the lamp follow these safety instructions:

• Unplug the electrical cord on the Canon LV-WX300 so there is no chance the projector could get turned on during the installation.
• The Canon LV-WX300 operates under high temperatures so give it at least one hour to cool down before opening the projector to change the projector lamp.

• Loosen the screw holding the Canon LV-LP39 projector lamp cover in place.

  Lift the lamp cover up. Do not turn the power on with the lamp cover removed.

• Using the handle pull out the Canon LV-LP39 projector lamp assembly. NOTE: The 
• Canon LV-LP39 contains mercury and should be properly recycled. Don’t throw it into regular garbage.

• Replace the lamp assembly with a new Canon LV-LP39 projector lamp. Be careful not to touch the actual bulb as oil from your fingers can leave black marks on the lamp.
• Close the lamp cover

Resetting the lamp timer counter

After replacing the Canon LV-WX300 projector lamp, you’ll need to reset the lamp. To reset:

• Restart the projector.
• Open the On-Screen Display (OSD) menu.
• Go to the SYSTEM SETUP: Advanced>Lamp Settings menu.
• Press OK/IMAGE. The Lamp Settings page is displayed. Press to highlight/ Reset lamp timer and press OK/IMAGE.
• A warning message is displayed asking if you want to reset the lamp timer. Highlight Reset and press OK/IMAGE . The lamp time will be reset to ‘0’.

Learn how to prolong lamp life with Top tips for extending projector lamp life.

The post Replace the Canon LV-WX300 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

End of life warnings

You can expect up to 4000 hours of use with your NEC LT180 projector lamp. When the lamp is reaching end of life you’ll see the following warning signs:

• The projected image gets darker or starts to deteriorate.
• The projector’s lamp light flashes orange or red at half-second intervals.
• The message Replace the lamp appears on the screen when you start projecting.

• NEC LT180 Projector Assembly with High Quality Original Bulb Inside
• NEC LT180 Replacement Projector Lamp 50028199 / LH02LP
  

Invest in authentic lamps

The best type of projector lamp for your NEC LT180 projector is an OEM authentic lamp. You’ll need model NEC LH02LP replacement projector lamp.

While counterfeits appear of be a bargain they often end up costing more in the long run since they are prone to explosions and have a much shorter lamp life. The other concerns are the lack of proper safety guards for your eyesight and damaging the sensitive electronics in your NEC LT180 projector.

Changing the projector lamp

Follow these important safety instructions before installing the new NEC LH02LP projector lamp

• turn off the NEC NP1000 projector.
• unplug the projector from its power source.
• unplug the power cable.
• wait until the projector is cool to the touch to avoid getting burned.

Step 1

Step 2

Step 2:  Loosen the lamp cover screw until the screwdriver goes into a freewheeling condition and remove the lamp cover. The lamp cover screw is not removable.

Step 3

Step 3: Loosen the two screws securing the NEC LH02LP lamp housing until the screwdriver loosens. The two screws are not removable. Remove the lamp housing by holding it by the edges. NOTE: The NEC LH02LP lamp contains mercury and should not be thrown into the garbage. Please recycle this lamp properly.

Step 4

Step 4: Insert a new NEC LH02LP lamp housing until the lamp housing is plugged into the socket. Secure it in place with the two screws. Be sure to tighten the screws. Align the lamp housing with the guide rail. Make sure the lamp housing plug goes to the socket correctly. If both screws are not tightened securely, an image may not be displayed correctly.

Step 5

Step 5: Reattach the lamp cover. Tighten the lamp cover screw. Be sure to tighten the screw. You are now ready to reset the lamp timer.

Reset the lamp timer

Once the NEC LH021LP projector lamp has been replaced you’ll need to reset the timer back to zero so the  NEC LT180 projector can accurately track the lamp life.  To reset:

• Open the menu
• Scroll down to the RESET option. Press ENTER.
• Scroll down to Clear Lamp Hour Meter. Press ENTER.
  
• The lamp timer will be set to zero.

Extend lamp life

• Keep your air filters clean to avoid overheating the projector.
• Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours
• Learn more with Top tips for extending DLP projector lamp life.

The post Installing a replacement NEC LT180 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

SpArc Platinum 3D Perception 400-0003-00 Projector Replacement Lamp with Housing

Go with authentic

Your 3D HMR-15 projector uses the  3D Perception 400-0003-00 lamp. Be sure to purchase an authentic projector lamp and avoid the temptation of generic lamps and their associated problems:

• shorter lamp life
• prone to explosions
• manufactured with toxic and dangerous substitutes
• can’t be properly calibrated
• voids your projector warranty if you install a generic

Save yourself hassle and go with an authentic projector lamp.

Replacing the lamp

Before replacing the projector lamp:

• Wait until the projector is cool to the touch before removing the lamp. These projector work at a high temperatures and you can get badly burned.
• Be sure to unplug the projector before replacing the lamp.

Insert the new 3D Perception 400-0003-00 lamp

into the projector making sure the wiring element has been reconnected and clicked into place. (Step C and D) Fasten the screw on the lamp.

Resetting the lamp timer

 

To reset the timer:

• Turn on the proector.
• Select Projectors on the drop-down menu under Maintenance under the main File menu.
• Scroll over to the LAMP option on the top menu.
• You’ll see the Current lamp time and Total lamp time.  This will be the old lamp information.
• Click on RESET to set the Total lamp time back to zero. Until you do this step, the 3D HMR-15 projector will think the lamp is still old and not turn on.

Extend the 3D HMR-15 lamp life

• Keep your air filters clean to avoid overheating the projector.
• Turn off the projector and let it rest for at least two hours a day.
• Make sure there is enough airflow around the projector particularly if it’s mounted on the ceiling.
• Learn more with Top tips for extending DLP projector lamp life.

Save

Save

Save

Save

Save

The post Replacing the 3D HMR-15 projector lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.

When the Toshiba 42HM66 TV lamp is reaching end of life you may notice that colors appear flattened and the brightness of has diminished. The quartz glass also gets weaker so if you hear a very loud bang, it means the lamp has exploded and needs to be replaced.

Buy this lamp on Amazon from the following authorized dealers:

• Toshiba Replacement Lamp with Housing and Original Bulb for 42HM66; 72620067; D42-LMP
• Toshiba RPTV Lamp Part 72620067 D42-LMP Model Toshiba 42HM66 RPTV 42HM66
• Toshiba 42HM66 DLP Projection TV Brand New High Quality Original Projector Bulb
• Toshiba 42HM66 150 Watt RPTV Replacement Lamp/Bulb

Keep it authentic

Reduce hassles by always buying authentic. Look for the seal of approval — don’t get caught with a copycat generic projector lamp!

6 reasons to avoid generic projection lamps:

• shorter lamp life than original lamps
• created with toxic materials and carcinogenic parts including Krypton-85
• prone to explosions
• can damage the sensitive electronics in your projector
• when you buy copy-cat lamps you get no guarantee or refunds
• installing a generic lamp can void your projector’s warranty.

Your Toshiba 42HM66 uses the Toshiba D42-LMP TV Lamp 

Replacing the lamp

Before replacing the lamp allow the Toshiba 42HM66 TV to cool down for one hour. There is a risk of a serious burn if the TV is not completely cool. Be sure to unplug the TV from the electrical socket.

Step 1

Step 1: The Toshiba 42HM66 TV lamp door is located on the side of the TV.  Loosen the screw and then remove the lamp unit door.

Note: The lamp unit door is provided with an interlock to reduce the risk of electric shock and excessive ultraviolet radiation. Never defeat its purpose or attempt to servicewithout removing the lamp unit door completely. Failure to follow this WARNING may result in death or serious injury.

Step 2

Step 2: Using a slotted screwdriver or a coin, loosen the two screws on the Toshiba D42-LMP lamp.

Step 3

Step 3: Grasp the Toshiba D42-LMP lamp by the handle and gently pull it straight out of the TV. Set the old lamp unit aside.

NOTE: The contains mercury. Please recycle this lamp. Don’t throw it into conventional garbage.

Step 4

Step 4:  Carefully insert the new lamp unit straight into the TV until it is fully seated. Avoid touching the actual bulb as this can affect image quality.

Step 5

Step 5: Hand-tighten the screws on the  Toshiba D42-LMP lamp Do not use an electric screwdriver

Step 6

Step 6: Reattach the lamp unit door, making sure to insert the hooks on the left side of the lamp unit door inside the
opening in the TV cabinet. Replace the door screw and tighten.

Plug in the power cord and turn on the TV. After the initial warmup period (which may take several seconds for full
picture brightness), the TV should operate normally.

If any there is no picture or a very dark picture or if the TV won’t turn on, repeats the steps again to ensure the lamp has been installed properly and the lamp door has been re-installed correctly.

Extend the life of the Toshiba D42-LMP lamp by following these tips.

The post Replacing the Toshiba 42HM66 TV lamp appeared first on DLP Lamp Guide - LCD and DLP Repair Tips - Fix Your DLP - FixYourDLP.com.